Organic additive-copper(II) complexes as plating precursors

Cu(II) ions previously coordinated with typical electroplating organic additives were investigated as an alternative source of metal for plating bath. The coordination complexes were isolated from reaction between CuSO(4) and organic additives as ligands (oxalate ion, ethylenediamine or imidazole). Deposits over 1010 steel were successfully obtained from electroplated baths using the complexes without any addition of free additives, at pH = 4.5 (H(2)SO(4)/Na(2)SO(4)). These deposits showed better morphologies than deposits obtained from CuSO(4) solution either in the absence or presence of oxalate ion as additive (40 mmol L(-1)), at pH = 4.5 (H(2)SO(4)/Na(2)SO(4))It is suggestive that the starting metal plating coordinated with additives influences the electrode position processes, providing deposits with corrosion potentials shifted over + 200 mV in 0.5 mol L(-1) NaCl (1 mV s(-1)). The resistance against corrosion is sensitive to the type of additive-complex used as precursor. The complex with ethylenediamine presented the best deposit results with the lowest pitting potential (-0.27 V vs 3.0 mol L(-1) CE). It was concluded that the addition of free additives to the electrodeposition baths is not necessary when working with previously coordinated additives. Thus, the complexes generated in ex-situ are good alternatives as plating precursors for electrodeposition bath. (C) 2009 Elsevier B.V. All rights reserved.

Slip during tension testing of Mg-3A1-1Zn sheet

The activation of slip and twinning deformation modes in Mg-3Al-1Zn alloy was investigated by means of both in-situ and ex-situ methods at ambient temperature using electron back scattering diffraction (EBSD). The results confirm the importance of non-basal slip and c-axis compression double twinning. During tensile deformation of rolled sheet, 63% of the observed slip traces were ascribed to prismatic slip, 33% to basal slip and 4% to <c+a> slip. Prismatic slip was frequently observed in grain interiors. The density of twinning was quantified in samples tested along transverse, extrusion and rolling directions at failure. The values in the range of 0.02-0.18 twins per square micron were found depending on sample orientation. The results show the effect of twinning on failure.

Self-assembly and film stability of a micelle of a single-chain quaternary ammonium amphiphile containing azobenzene on mica

The self-assembling behavior of a single-chain quaternary ammonium amphiphile bearing azobenzene (C₁₂AzoC₆N⁺) on freshly cleaved mica sheet has been investigated by atomic force microscopy (AFM) method. Confocal microscopic Raman spectra confirm the adsorption of the self-assembled monolayer structure. Ex-situ AFM reveals that C₁₂AzoC₆N⁺ forms branch-like stripes indicating the fusion and reorganization of the micelles during drying in air as the in-situ AFM has revealed that surfactant forms spherical micelles on the mica surface. The nano-sized surface structure is strongly dependent on the change of molecular structure, which resulted from photo-induced isomerization. The nano-sized stripe is quite stable even being annealed at 90 °C for 4 h.

The miscibility of poly(d,l-lactide-co-glycolide) with amphiphilic molecules and the interaction of their mixtures with DNA at air/water interface

The miscibility of poly(d,l-lactide-co-glycolide) (PLG) with three amphiphilic molecules and the interaction of the PLG/surfactant mixtures with DNA at air/water interface are investigated by π-A isotherms, Brewster angle microscopy (BAM) and atomic force microscopy (AFM) techniques. The π-A isotherms of the PLG mixtures with cationic C12AzoC6PyBr, and C12AzoC6N(CH3)3Br, are quite different from the π-A isotherm of pure PLG on water subphase. In contrast to the case, the π-A isotherm of PLG mixed with nonionic C12AzoC6OPy is almost identical to the pure PLG except some increasing of molecular area. Similar phenomena are observed on DNA subphase. The in situ BAM and ex situ AFM observations demonstrate that the dispersion of PLG at air/water interface becomes good when it mixes with the two cationic surfactants, whereas quite poor due to the phase separation when it mixes with the nonionic amphiphilic molecule. Based on these results we conclude that the cationic surfactants can affect the conformation change of PLG at air/water interface and figure a well miscibility with polymer whereas the nonionic amphiphilic molecule presents poor miscibility. In addition, the even mixing of the PLG and the cationic surfactants is favorable for the adsorption to DNA more effectively.

Monolayer behavior of a pyridyl head-group-containing amphiphile and its miscibility with poly(D,L-lactide-co-glycolide) on different pH subphase

In this paper, we investigated the Langmuir film and Langmuir–Blodgett (LB) monolayer film of a nonionic amphiphilic molecule, 4-(6-p-pyridyloxyl)hexyloxyl-4′-dodecyloxylazobenzene (C12AzoC6Py) and its mixture with poly(d,l-lactide-co-glycolide) (PLG) at different subphase pH values (2.0, 2.6, 3.3, 4.4, and 6.5, respectively) by surface pressure–area (π–A) isotherms, in situ interface Brewster angle microscopy (BAM), and ex situ atomic force microscopy (AFM). For pure C12AzoC6Py, its π–A isotherms display a plateau when the subphase pH value is lower than 3.0. The pressure of the plateau increases with the decrease of pH until 2.0. Over the plateau, the π–A isotherms become almost identical to the one under neutral conditions. The appearance of such a plateau can be explained as the coexistence of protonation and unprotonation of pyridyl head groups of the employed amphiphile. In contrast to the homogeneous surface morphology of pure C12AzoC6Py near the plateau by BAM observation, the surface in the case of its mixing with PLG exhibits a dendritic crystalline state under low surface pressure at subphase pH lower than 3.0. The crystalline state becomes soft and gradually melts into homogeneous aggregates with surface pressure increasing to a higher value than that of the plateau. Meanwhile, the hydrolysis of PLG in the mixture system at the interface has been affirmed to be restrained to a very large extent. And the PLG was believed to be compelled to the up layer of the LB film due to the phase separation, which is examined by AFM. Based on the experimental results, the corresponding discussion was also performed.

Chemisorbed and physisorbed Structures for 1,10-Phenanthroline and Dipyrido[3,2-a:2',3'-c]phenazine on Au(111)

Scanning tunneling microscopy (STM) images of 1,10-phenanthroline (PHEN) and dipyrido[3,2-a:2‘,3‘-c]phenazine (DPPZ) on Au(111) are recorded using both in situ and ex situ techniques. The images of PHEN depict regimes of physisorption and chemisorption, whereas DPPZ is only physisorbed. All physisorbed structures are not pitted and fluctuate dynamically, involving aligned (4 × 4) surface domains with short-range (ca. 20 molecules) order for PHEN but unaligned chains with medium-range (ca. 100 molecules) order for DPPZ. In contrast, the chemisorbed PHEN monolayers remain stable for days, are associated with surface pitting, and form a (4 × √13)R46° lattice with long-range order. The density of pitted atoms on large gold terraces is shown to match the density of chemisorbed molecules, suggesting that gold adatoms link PHEN to the surface. For PHEN, chemisorbed and physisorbed adsorbate structures are optimized using plane-wave density-functional theory (DFT) calculations for the surface structure. Realistic binding energies are then obtained adding dispersive corrections determined using complete-active-space self-consistent field calculations using second-order perturbation theory (CASPT2) applied to cluster-interaction models. A fine balance between the large adsorbate−adsorbate dispersive forces, adsorbate−surface dispersive forces, gold ligation energy, and surface mining energy is shown to dictate the observed phenomena, leading to high surface mobility and substrate/surface lattice incommensurability. Increasing the magnitude of the dispersive forces through use of DPPZ, rather than PHEN, to disturb this balance produced physisorbed monolayers without pits and/or surface registration but with much longer-range order. Analogies are drawn with similar but poorly understood processes involved in the binding of thiols to Au(111).

The influence of unburnt patches and distance from refuges on post-fire bird communities

Predicting the response of faunal communities to fire presents a challenge for land managers worldwide because the post-fire responses of species may vary between locations and fire events. Post-fire recovery can occur via nucleated recovery from in situ surviving populations or by colonization from ex situ populations. Fine-scale spatial patterns in the patchiness of fires and the proximity of burnt sites to source populations may contribute to both the variability in post-fire responses and the processes by which populations recover. We examined the avifauna at recently burnt sites within extensive semi-arid shrublands of south-eastern Australia, including 72 sites < 5 years since fire and 26 sites 10 years since fire. Study sites represented a gradient of increasing distance from ‘unburnt’ vegetation (i.e. > 27 years since fire) and varied in the presence or absence of small (25–900 m2) unburnt patches of vegetation. For sites < 5 years since fire, species richness was higher at sites closer to unburnt vegetation and at sites containing unburnt patches. These patterns were no longer evident at sites of 10 years since fire. The probability of occurrence of three of seven bird species modelled decreased with increasing distance to unburnt vegetation, but this pattern was evident only at sites burnt uniformly. One species was found almost exclusively at patchily burnt sites. These results are consistent with the hypothesis that proximity to unburnt vegetation enhances post-fire occupancy, and that colonization from ex situ populations is an important process for post-fire recovery of avifauna. Additionally, small unburnt patches enhance the rapid recovery of assemblages post-fire. These patterns are important for understanding the dynamics of post-fire population recovery. We recommend that management of fire for ecological purposes should explicitly consider the role that the spatial attributes of fires play in determining the post-fire community.

Phosphorus-carbon nanocomposite anodes for lithium-ion and sodium-ion batteries

With the expected theoretical capacity of 2596 mA h g-1, phosphorus is considered to be the highest capacity anode material for sodium-ion batteries and one of the most attractive anode materials for lithium-ion systems. This work presents a comprehensive study of phosphorus-carbon nanocomposite anodes for both lithium-ion and sodium-ion batteries. The composite electrodes are able to display high initial capacities of approximately 1700 and 1300 mA h g-1 in lithium and sodium half-cells, respectively, when the cells are tested within a larger potential windows of 2.0-0.01 V vs. Li/Li+ and Na/Na+. The level of demonstrated capacity is underpinned by the storage mechanism, based on the transformation of phosphorus to Li3P phase for lithium cells and an incomplete transformation to Na3P phase for sodium cells. The capacity deteriorates upon cycling, which is shown to originate from disintegration of electrodes and their delamination from current collectors by post-cycling ex situ electron microscopy. Stable cyclic performance at the level of ∼700 and ∼350-400 mA h g-1 can be achieved if the potential windows are restricted to 2.0-0.67 V vs. Li/Li+ for lithium and 2-0.33 vs. Na/Na+ for sodium half-cells. The results are critically discussed in light of existing literature reports

Understanding structure-function relationship in hybrid Co3O4-Fe2O3/C lithium-ion battery electrodes

A range of high-capacity Li-ion anode materials (conversion reactions with lithium) suffer from poor cycling stability and limited high-rate performance. These issues can be addressed through hybridization of multiple nanostructured components in an electrode. Using a Co3O4-Fe2O3/C system as an example, we demonstrate that the cycling stability and rate performance are improved in a hybrid electrode. The hybrid Co3O4-Fe2O3/C electrode exhibits long-term cycling stability (300 cycles) at a moderate current rate with a retained capacity of approximately 700 mAh g(-1). The reversible capacity of the Co3O4-Fe2O3/C electrode is still about 400 mAh g(-1) (above the theoretical capacity of graphite) at a high current rate of ca. 3 A g(-1), whereas Co3O4-Fe2O3, Fe2O3/C, and Co3O4/C electrodes (used as controls) are unable to operate as effectively under identical testing conditions. To understand the structure-function relationship in the hybrid electrode and the reasons for the enhanced cycling stability, we employed a combination of ex situ and in situ techniques. Our results indicate that the improvements in the hybrid electrode originate from the combination of sequential electrochemical activity of the transition metal oxides with an enhanced electronic conductivity provided by percolating carbon chains.

Electrochemical impedance spectroscopy as a tool to measure cathodic disbondment on coated steel surfaces: capabilities and limitations

The disbondment of protective organic coatings under excessive cathodic protection potentials is a widely reported coating failure mechanism. Traditional methods of evaluating cathodic disbondment are based on ex situ visual inspection of coated metal surfaces after being exposed to standard cathodic disbondment testing conditions for a long period of time. Although electrochemical impedance spectroscopy (EIS) has been employed as an effective means of evaluating various anti-corrosion properties of organic coatings; its application for assessing the cathodic disbondment resistance of coatings has not been sufficiently exploited. This paper reports an experimental study aimed at developing EIS into a tool for in situ measurement and monitoring of cathodic disbondment of coatings. A clear correlation between EIS parameters and the disbonded coating areas has been confirmed upon short term exposure of epoxy-coated steel electrodes to cathodic disbondment conditions; however the degree of this correlation was found to decrease with the extension of exposure duration. This observation suggests that EIS loses its sensitivity with the propagation of coating disbondment, and that in order to achieve quantitative determination of the coating cathodic disbondment localized EIS measurements are required to measure the parameters related to local disbonded areas.

Ensaio clínico randomizado da preservação de enxertos hepáticos com solução de perfusão de UW e HTK no transplante ortotópico de fígado

Introdução: A solução de UW (University of Wisconsin) tem sido utilizada como padrão para preservação de enxertos hepáticos para transplante ortotópico de fígado (TOF) desde 1990. Seu custo é alto, e não existem, em nosso meio, estudos clínicos que comparem a sua efetividade com a de outras soluções. A solução de HTK (histidina-triptofano-cetoglutarato) foi desenvolvida inicialmente para cardioplegia, porém estudos experimentais e alguns estudos clínicos retrospectivos demonstraram sua eficácia na preservação hepática, mesmo com tempos de isquemia prolongados. Objetivos: Comparar a efetividade das soluções de preservação de órgãos HTK e UW com relação as variáveis: disfunção primária do enxerto (DPE), tempo de isquemia fria (TIF), complicações de via biliar (CVB), alterações de provas funcionais hepáticas (PFH) e sobrevida do enxerto e dos pacientes. Método: Foram estudados os fígados de doadores de múltiplos órgãos, implantados nos receptores pela técnica de piggyback, segundo ordem cronológica de ingresso em lista de espera no RS no período janeiro de 2003 a agosto de 2004. As soluções de preservação HTK e UW foram utilizadas de forma randomizada em blocos. A perfusão na aorta foi feita com 4 litros de HTK ou 2 litros de UW e a perfusão venosa portal com 1 litro de ambas as soluções, utilizando-se 500 ml para perfusão venosa e arterial adicional ex-situ e armazenagem do enxerto. Realizou-se biópsia hepática em cunha do lobo esquerdo quando a esteatose macroscópica estava presente. A análise bioquímica sérica foi diária na primeira semana e, em 15 e 30 dias pós-operatórios. Resultados: Foram estudados 102 pacientes submetidos ao TOF, sendo 65 no grupo UW (63,7%) e 37 no grupo HTK (36,3%). As frequências de sexo, raça, estado hemodinâmico, o uso de vasopressores e a presença de esteatose nos doadores foram igual nos dois grupos (pα>,05). A idade média dos doadores foi de 38,1 anos (DP +-14,4) no grupo UW e de 44,6 anos (DP +-14,2) no HTK (pα=,036). A distribuição de sexo, raça, idade, etiologia da cirrose, re-transplante, hepatite fulminante, trombose portal e escore de Child-Pugh dos receptores foi igual nos dois grupos (pα>,05). O grupo HTK teve 8 casos (25,8%) de CVB (4 estenose, 2 fístulas e 2 lesões do tipo isquêmica) contra 5 casos (8,6%) do grupo UW (pα=,033) em 89 pacientes que completaram 4 meses de seguimento (OR=2,0; IC 95%=1,2 a 3,5). A média do TIF nos dois grupos foi semelhante (UW= 579,2 min.; HTK= 527,9 min. pα>,05) e não houve diferenças nas incidências de CVB, DPE e óbito com relação a TIF estratificados entre os grupos. Não houve variação nas medianas das PFH (pα>,05 para BT, AST, ALT, FA, GGT, LDH, Fator 5 e TP). A incidência de óbito foi similar em ambos os grupos: UW= 6 (9,4%) e HTK= 4 (11,1%). A incidências de DPE foi de 2,8% no grupo HTK (1 caso) e 9,4% no grupo UW (6 casos) (pα=0,15), dos quais 5 (71,4%) evoluíram para o óbito por não funcionamento primário do enxerto, com ou sem outras morbidades. Conclusão: As soluções de UW e HTK foram igualmente efetivas na preservação dos enxertos hepáticos de doadores cadavéricos na amostra analisada, considerando-se aspectos clínicos, laboratoriais e sobrevida dos pacientes e dos enxertos. A utilização rotineira da solução de HTK poderá diminuir os custos do TOF. A média de idade maior dos doadores e a utilização de um volume reduzido de solução podem ter contribuído para uma incidência maior de CVB no grupo HTK.

Avaliação de dois métodos para condicionamento e coleta de sêmen em quatro espécies do gênero Mazama

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Mating system parameters at hierarchical levels of fruits, individuals and populations in the Brazilian insect-pollinated tropical tree, Tabebuia roseo-alba (Bignoniaceae)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Development and characterization of 14 microsatellite loci from an enriched genomic library of Eucalyptus camaldulensis Dehnh

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Diretrizes para conservação da espécie Mimosa Caesalpiniifolia Benth., Macaíba-RN

About 40% of the earth is occupied by tropical and subtropical forests, including 42% of dry forests, where there is Caatinga Bioma, contemplating tree forests and shrubs, with xerophytic characteristics. Study and conservations of Caatinga biologic diversity is one of the greatest challenges of Brazilian science because those are, proportionally, the less studied among natural areas, with most of the scientific effort centered in very few points around the main cities in the area and also because it is the less protected natural Brazilian area. The environmental degradation is constantly increasing and has its rhythm accelerated by the men appropriation to meet or not their own needs. Therefore, species conservation should be based in three principles: the use of natural resources by present generation, waste prevention and use of the natural resources to benefit the majority of the citizens. Among the strategies to species conservation, we can mention the ex situ conservation , in which the conservation of genetic resources may be realized outside of the natural environment in which the species occur, and in situ conservation , or, in other words, in the places where the species occur. In ex situ conservation, the germplasm collections are maintained in the field and/or in laboratories (conservation chambers), and this mainly conserves intraspecific diversity (genetic variance), the ex situ collections are continuously enriched by collection activities, introduction and germplasm interchange; the in situ conservation preserving ecosystems and habitats, maintaining and recovering native population of species of interest. So, the objective of this paper is the search for strategies to the conservation of Mimosa caesalpiniifolia B. (sabiá) using instruments of environmental perception and plant biotechnology, as mechanisms of in situ and ex situ conservation. To environmental perception, were realized open, semi-structured and qualitative interviews. The questions included socioeconomic data and knowledge of Sabiá specie. To plant biotechnology, Sabiá seed collection were realized in different location to formation of a germplasm bank. The specie micropropagation was made from nodal segment of plants from the matrizeiro. About the knowledge of rural populations and the use of Sabiá plant, some preferences occurred from speeches that the plant possesses a firm wood, not attacked by termites, legalized for exploration by the Brazilian environmental organ (IBAMA), and is a native specie. This research found the rural population has knowledge about Sabiá specie and the natural resources are exhausting. The proposal that the rural community brought was the donation of the Sabiá specie seeding initiating on the rain season, in which the seeding would be plated between the lots, in individual plantations. To the formation of a matrix bank, plant biothecnology brought answers favorable to Sabiá specie seeding, with the formation of multiple shoots