994 resultados para Dry products


Relevância:

20.00% 20.00%

Publicador:

Resumo:

Controversy exists in the published literature as to the effect of silicon content and pressure on the dry sliding wear of Al---Si alloys. The present paper attempts to clarify the question by reporting a statistical analysis of data obtained from factorially designed experiments conducted on a pinon-disc machine in the pressure range 0.105–1.733 MPa and speed range 0.19–0.94 m s−1. Under these conditions it was found that, in the range 4–24 wt.% Si, wear of binary unmodified alloys does not significantly differ between the alloys. However, it is significantly less than that corresponding to an alloy containing no silicon. The effect of pressure on wear rate was found to be linear and monotonie and, over the narrow range of speeds used, the wear rate was found to be unaffected by speed. The coefficient of friction was found to be insensitive to variations in silicon content, pressure and speed.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Formative time lags in nitrogen, oxygen, and dry air are measured with and without a magnetic field over a range of gas pressures (0.05 ' p ' 20.2 torr 5 kPa to 2 MPa, electric field strengths (1.8xO14 EEs 60xlO V m l) and magnetic field strengths (85xl0-4 < B ' 16x10-2 Tesla). For experiments below the Paschen minimum, the electrodes are designed to ensure that breakdown occurs over longer gaps and for experiments above the Paschen minimum, a coaxial cylindrical system is employed. The experimental technique consists of applying pulse voltages to the gap at various constant values of E/p and B/p and measuring the time lags from which the formative time lags are separated. In the gases studed, formative time lags decrease on application of a magnetic field at a given pressure for conditions below the Paschen minimum. The voltages at which the formative time lags remain the same without and with magnetic fields are determined, and electron molecule collision frequencies (v/p) are determined using the Effective Reduced Electric Field [EREF] concept. With increasing ratio of E/p in crossed fields, v/p decreases in all the three gases. Measurements above the Paschen minimum yield formative time lags which increase on application of a magnetic field. Formative time lags in nitrogen in ExB fields are calculated assuming an average collision frequency of 8.5x109 sec-1 torr 1. It is concluded that the EREF concept can be applied to explain formative time lags in ExB fields.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

The products of corrosion reaction of electrolytic iron in 45% ammonium nitrate solution formed under various conditions of time, temperature and pH have been analysed mainly by Mössbauer spectroscopy, in combination with X-ray diffraction, infrared absorption and electron microscopy techniques. γ-Fe00H is found to be the major product of hydrolytic precipitation at pH > 5.6 while only α-FeOOH is formed at pH < 3.0. In the pH range 3.0 < pH < 5.0, α-Fe00H and ferrihydrite are both formed. However, once the nuclei of α-Fe00H are formed under low pH conditions, their growth is favoured even in the otherwise unfavourable slightly acidic medium, resulting in a hydrous α-Fe00H which has two distinct hyperfine fields at the 57Fe nucleus. Magnetite is always formed in the vicinity of the metal and its rate of formation on the surface increases with temperature. α-Fe203 is the major product of hydrolytic precipitation at temperatures >80C. The possible mechanisms for the formation of each of the corrosion products are discussed.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

In the seasonally dry tropics of northern Australia, breeder cows may lose up to 30% liveweight during the dry season when pasture is of low nutritive value. This is a major cause of low reproductive rates and high mortality. Weaning early in the dry season is effective to reduce this liveweight loss of the breeder (Holroyd et al. 1988). An experiment examined the dry season liveweight loss of breeders for a range of weaning times and levels of nutrition. From April to October through the dry season, 209 Bos indicus x Shorthorn cross cows 4-6 years of age grazed speargrass pastures in north Queensland. The cows had been joined with bulls from late January until April. Twenty-nine breeders had not suckled a calf during the previous wet season (DRY cows). In addition 180 cows lactating in April were weaned in late April, mid July or early September. The cows were allocated by stratified randomisation based on lactational status, stage of pregnancy and body condition to 15 x 40 ha paddocks. Five paddocks with low fertility soils provided LOW nutrition, while 10 paddocks with medium fertility soils and no supplementation or with supplementation provided MEDIUM and HIGH nutrition, respectively. The supplement consisted of molasses containing 14% urea offered ad libitum. Liveweight was measured at intervals and conceptus-free liveweight (CF-LW) calculated. Data were analyses by AOV within groups of paddocks. Animal production for a consuming world : proceedings of 9th Congress of the Asian-Australasian Association of Animal Production Societies [AAAP] and 23rd Biennial Conference of the Australian Society of Animal Production [ASAP] and 17th Annual Symposium of the University of Sydney, Dairy Research Foundation, [DRF]. 2-7 July 2000, Sydney, Australia.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Supplements containing urea or biuret were fed in the dry season to yearling and two year old pregnant heifers grazing native spear grass pastures in north Queensland. Liveweight change and survival during the dry season and fertility in the following year were measured. In the first experiment during a relatively favourable dry season, supplementation significantly (P<0.01) reduced liveweight loss in yearling heifers (5 vs. 32 kg). In the following year during a drought, supplement significantly (P<.01) reduced liveweight loss in yearling heifers (32 vs. 41 kg) and significantly (P <0.01) reduced mortalities (23.5% vs. 5.2%) in pregnant and lactating heifers. The supplement had no significant effect on subsequent fertility in either experiment. 14th Biennial Conference.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Nematospora (Eremothecium) coryli was isolated from Citrus and identified for the first time in Australia. This insect-transmitted yeast was associated with dry rot in cultivated and native Citrus fruits. Although N. coryli is known as a serious seed pathogen of many tropical and sub-tropical plants, evidence is presented that it has been present and undetected in Queensland for at least ninety years.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Aseptic processing involves sterilising the product (most meat products being low-acid foods containing particulates) and package separately, and filling under sterile conditions. Advantages include better product quality compared with canned products, lower transport and storage costs compared with frozen products, and virtually no restriction on package size. Problems include ensuring adequate heat penetration into the particles to ensure sterility, preventing separation of particles from the carrier liquid, and retention of particle structure and shape. Particulate foods can be sterilised in scraped-surface heat exchangers. Other methods involve heating the particles separately, and combining them during filling. The effects of aseptic processing on meat product quality (colour, flavour, texture, and mutrition) are outlined in this paper.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Quantifying the local crop response to irrigation is important for establishing adequate irrigation management strategies. This study evaluated the effect of irrigation applied with subsurface drip irrigation on field corn (Zea mays L.) evapotranspiration (ETc), yield, water use efficiencies (WUE = yield/ETc, and IWUE = yield/irrigation), and dry matter production in the semiarid climate of west central Nebraska. Eight treatments were imposed with irrigation amounts ranging from 53 to 356 mm in 2005 and from 22 to 226 mm in 2006. A soil water balance approach (based on FAO-56) was used to estimate daily soil water and ETc. Treatments resulted in seasonal ETc of 580-663 mm and 466-656 mm in 2005 and 2006, respectively. Yields among treatments differed by as much as 22% in 2005 and 52% in 2006. In both seasons, irrigation significantly affected yields, which increased with irrigation up to a point where irrigation became excessive. Distinct relationships were obtained each season. Yields increased linearly with seasonal ETc (R 2 = 0.89) and ETc/ETp (R 2 = 0.87) (ETp = ETc with no water stress). The yield response factor (ky), which indicates the relative reduction in yield to relative reduction in ETc, averaged 1.58 over the two seasons. WUE increased non-linearly with seasonal ETc and with yield. WUE was more sensitive to irrigation during the drier 2006 season, compared with 2005. Both seasons, IWUE decreased sharply with irrigation. Irrigation significantly affected dry matter production and partitioning into the different plant components (grain, cob, and stover). On average, the grain accounted for the majority of the above-ground plant dry mass (≈59%), followed by the stover (≈33%) and the cob (≈8%). The dry mass of the plant and that of each plant component tended to increase with seasonal ETc. The good relationships obtained in the study between crop performance indicators and seasonal ETc demonstrate that accurate estimates of ETc on a daily and seasonal basis can be valuable for making tactical in-season irrigation management decisions and for strategic irrigation planning and management.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Whether or not termites initiate damage to timber via the end grain may determine the need for spot-treating the exposed untreated cut ends of envelope-treated softwood framing material. Australian Coptotermes acinaciformis (Froggatt) were field-tested for their ability to initiate feeding via the end grain of timber (35 × 90 mm) treated with a repellent Tanalith® T envelope. Specimens of commercial radiata pine Pinus radiata D.Don framing timber (untreated) and slash pine Pinus elliottii Englem. (untreated and envelope-treated) were partially clad in fine stainless steel mesh. Clad and unclad specimens were exposed to C. acinaciformis near Townsville, North Queensland, Australia, for four months. Results showed that this species of termite can indeed damage timber via the end grain, including exposed untreated cut ends of envelope-treated material as demonstrated earlier for different populations of C. acinaciformis. Differences between the test conditions in field trials carried out at different times (where C. acinaciformis either did or did not damage timber via the end grain) are discussed. Clearly, outcomes from field studies with preservative-treated materials are dependent upon experimental conditions. Notably, the amount of bait wood (highly termite-susceptible timber substrate) offered in a given method can strongly influence the termite response. Further investigation is required to standardise this aspect of conditions in protocols for the assessment of wood preservatives.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Keeping in view the prospects of biodegradable polymers, a polymer was synthesized by the condensation of carboxy-terminated polybutadiene (CTPB) of Mnsim-5000 with glycerol and tested for its microbial susceptibility. The results of end group estimations and viscosity measurements indicated a quantitative reaction between the two reactants under experimental conditions. The clear-zone method was employed in this investigation to test biodegradability. Two strains of Serratia and three strains of Staphylococcus did show a clear zone surrounding the colony. However, the microbial growth was found to diminish after 4 or 5 days.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Timely access to effective technical information is a key ingredient of profitable strawberry production. Through the Better Berries Program, a joint RD&E initiative of government and industry, a number of information products and services have been provided in recent years to Australia's subtropical strawberry industry, centred in southern Queensland. However, there is a lack of knowledge of how well these are meeting the information needs of growers, both in content and delivery. To better understand grower information use and needs, a stratified sample of 25 growers was interviewed on-farm during the 2004 season. Growers were asked about how they currently accessed information, what they thought of a range of information products and ideas on show, and what advice they would provide for information development in the future. Results indicated that information sought by growers and the style in which it is best presented, varied considerably with grower experience, but little with farm size. New growers had a wide range of needs while the needs of experienced growers were focused mainly on problem identification and new production development. Interestingly, the overwhelming majority across all sectors still preferred paper-based information products despite their extensive use of computers for business purposes. The findings were used to develop a strategy for an improved range of technical information products and services that are more accessible, easier to use, more timely, and more relevant to the needs of growers.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Many arthropod predators and parasitoids exhibit either stage-specific or lifetime omnivory, in that they include extra-floral nectar, floral nectar, honeydew or pollen in their immature and/or adult diet. Access to these plant-derived foods can enhance pest suppression by increasing both the individual fitness and local density of natural enemies. Commercial products such as Amino-Feed®, Envirofeast®, and Pred-Feed® can be applied to crops to act as artificial-plant-derived foods. In laboratory and glasshouse experiments we examined the influence of carbohydrate and protein rich Amino-Feed UV® or Amino-Feed, respectively, on the fitness of a predatory nabid bug Nabis kinbergii Reuter (Hemiptera: Nabidae) and bollworm pupal parasitoid Ichneumon promissorius (Erichson) (Hymenoptera: Ichneumonidae). Under the chosen conditions, the provision of either wet or dry residues of Amino-Feed UV had no discernable effect on immediate or longer-term survival and immature development times of N. kinbergii. In contrast, the provision of honey, Amino-Feed plus extrafloral nectar, and extrafloral nectar alone had a marked effect on the longevity of I. promissorius, indicating that they were limited by at least carbohydrates as an energy source, but probably not protein. Compared with a water only diet, the provision of Amino-Feed plus extrafloral nectar increased the longevity of males and females of I. promissorius by 3.0- and 2.4-fold, respectively. Not only did female parasitoids live longer when provided food, but the total number of eggs laid and timing of deposition was affected by diet under the chosen conditions. Notably, females in the water and honey treatments deposited greater numbers of eggs earlier in the trial, but this trend was unable to be sustained over their lifetime. Egg numbers in these treatments subsequently fell below the levels achieved by females in the Amino-Feed plus extrafloral nectar and cotton extrafloral nectar only treatments. Furthermore, there were times when the inclusion of the Amino-Feed was beneficial compared with cotton extrafloral nectar only. Artificial food supplements and plant-derived foods are worthy of further investigation because they have potential to improve the ecosystem service of biological pest control in targeted agroecosystems by providing natural enemies with an alternative source of nutrition, particularly during periods of prey/host scarcity.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Milk obtained from cows on 2 subtropical dairy feeding systems were compared for their suitability for Cheddar cheese manufacture. Cheeses were made in a small-scale cheesemaking plant capable of making 2 blocks ( about 2 kg each) of Cheddar cheese concurrently. Its repeatability was tested over 10 separate cheesemaking days with no significant differences being found between the 2 vats in cheesemaking parameters or cheese characteristics. In the feeding trial, 16 pairs of Holstein - Friesian cows were used in 2 feeding systems (M1, rain-grown tropical grass pastures and oats; and M5, a feedlot, based on maize/barley silage and lucerne hay) over 2 seasons ( spring and autumn corresponding to early and late lactation, respectively). Total dry matter, crude protein (kg/cow. day) and metabolisable energy (MJ/cow.day) intakes were 17, 2.7, and 187 for M1 and 24, 4, 260 for M5, respectively. M5 cows produced higher milk yields and milk with higher protein and casein levels than the M1 cows, but the total solids and fat levels were similar (P > 0.05) for both M1 and M5 cows. The yield and yield efficiency of cheese produced from the 2 feeding systems were also not significantly different. The results suggest that intensive tropical pasture systems can produce milk suitable for Cheddar cheese manufacture when cows are supplemented with a high energy concentrate. Season and stage of lactation had a much greater effect than feeding system on milk and cheesemaking characteristics with autumn ( late lactation) milk having higher protein and fat contents and producing higher cheese yields.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

In the present investigation, the wear behaviour of a creep-resistant AE42 magnesium alloy and its composites reinforced with Saffil short fibres and SiC particles in various combinations is examined in the longitudinal direction i.e., the plane containing random fibre orientation is perpendicular to the steel counter-face. Wear tests are conducted on a pin-on-disc set-up under dry sliding condition having a constant sliding velocity of 0.837 m/s for a constant sliding distance of 2.5 km in the load range of 10-40 N. It is observed that the wear rate increases with increase in load for the alloy and the composites, as expected. Wear rate of the composites is lower than the alloy and the hybrid composites exhibit a lower wear rate than the Saffil short fibres reinforced composite at all the loads. Therefore, the partial replacement of Saffil short fibres by an equal volume fraction of SiC particles not only reduces the cost but also improves the wear resistance of the composite. Microstructural investigation of the surface and subsurface of the worn pin and wear debris is carried out to explain the observed results and to understand the wear mechanisms. It is concluded that the presence of SiC particles in the hybrid composites improves the wear resistance because these particles remain intact and retain their load bearing capacity even at the highest load employed, they promote the formation of iron-rich transfer layer and they also delay the fracture of Saffil short fibres to higher loads. Under the experimental conditions used in the present investigation, the dominant wear mechanism is found to be abrasion for the AE42 alloy and its composites. It is accompanied by severe plastic deformation of surface layers in case of alloy and by the fracture of Saffil short fibres as well as the formation of iron-rich transfer layer in case of composites.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

The potential of beef producers to profitably produce 500-kg steers at 2.5 years of age in northern Australia's dry tropics to meet specifications of high-value markets, using a high-input management (HIM) system was examined. HIM included targeted high levels of fortified molasses supplementation, short seasonal mating and the use of growth promotants. Using herds of 300-400 females plus steer progeny at three sites, HIM was compared at a business level to prevailing best-practice, strategic low-input management (SLIM) in which there is a relatively low usage of energy concentrates to supplement pasture intake. The data presented for each breeding-age cohort within management system at each site includes: annual pregnancy rates (range: 14-99%), time of conception, mortalities (range: 0-10%), progeny losses between confirmed pregnancy and weaning (range: 0-29%), and weaning rates (range: 14-92%) over the 2-year observation. Annual changes in weight and relative net worth were calculated for all breeding and non-breeding cohorts. Reasons for outcomes are discussed. Compared with SLIM herds, both weaning weights and annual growth were >= 30 kg higher, enabling 86-100% of HIM steers to exceed 500 kg at 2.5 years of age. Very few contemporary SLIM steers reached this target. HIM was most profitably applied to steers. Where HIM was able to achieve high pregnancy rates in yearlings, its application was recommended in females. Well managed, appropriate HIM systems increased profits by around $15/adult equivalent at prevailing beef and supplement prices. However, a 20% supplement price rise without a commensurate increase in values for young slaughter steers would generally eliminate this advantage. This study demonstrated the complexity of pro. table application of research outcomes to commercial business, even when component research suggests that specific strategies may increase growth and reproductive efficiency and/or be more pro. table. Because of the higher level of management required, higher costs and returns, and higher susceptibility to market changes and disease, HIM systems should only be applied after SLIM systems are well developed. To increase profitability, any strategy must ultimately either increase steer growth and sale values and/or enable a shift to high pregnancy rates in yearling heifers.