Halting the fuse discharge propagation Using optical fiber microwires

We report and analyze the halting of the fuse effect propagation in optical fiber microwires. The increase of the mode field diameter in the tapered region decreases the optical intensity resulting in the extinction of the fuse effect. This fiber element presents a low insertion loss and can be introduced in the optical network in order to protect the active equipment from the damage caused by the fuse effect. (C) 2012 Optical Society of America

Mode III interlaminar fracture of carbon/epoxy laminates using the edge crack torsion (ECT) test

The mode III interlaminar fracture of carbon/epoxy laminates was evaluated with the edge crack torsion (ECT) test. Three-dimensional finite element analyses were performed in order to select two specimen geometries and an experimental data reduction scheme. Test results showed considerable non-linearity before the maximum load point and a significant R-curve effect. These features prevented an accurate definition of the initiation point. Nevertheless, analyses of non-linearity zones showed two likely initiation points corresponding to GIIIc values between 850 and 1100 J/m2 for both specimen geometries. Although any of these values is realistic, the range is too broad, thus showing the limitations of the ECT test and the need for further research.

Fractional Dynamics of Computer Virus Propagation

We propose a fractional model for computer virus propagation. The model includes the interaction between computers and removable devices. We simulate numerically the model for distinct values of the order of the fractional derivative and for two sets of initial conditions adopted in the literature. We conclude that fractional order systems reveal richer dynamics than the classical integer order counterpart. Therefore, fractional dynamics leads to time responses with super-fast transients and super-slow evolutions towards the steady-state, effects not easily captured by the integer order models.

Propagation of waves generated by a pressure disturbance moving in a channel

This paper studies the effect of ship speed and water depth on the propagation of ship generated waves. The ship is represented by a moving pressure distribution function at the free surface that is able to reproduce most of the phenomena involved in wave propagation. Results are obtained for a ship sailing along a coastal stretch made of a sloping bottom and a constant depth region. The results show that in the sloping bottom the crests of waves are bent along the slope and in the constant depth the standard Kelvin wave patterns can be found for the subcritical regime. In the critical regime the wave system is characterized by significant diverging waves and for a supercritical regime, the transverse waves disappear. © 2015 Taylor & Francis Group, London.

Automated image tagging through tag propagation

Trabalho apresentado no âmbito do Mestrado em Engenharia Informática, como requisito parcial Para obtenção do grau de Mestre em Engenharia Informática

Fractional Dynamics of Computer Virus Propagation

We propose a fractional model for computer virus propagation. The model includes the interaction between computers and removable devices. We simulate numerically the model for distinct values of the order of the fractional derivative and for two sets of initial conditions adopted in the literature. We conclude that fractional order systems reveal richer dynamics than the classical integer order counterpart. Therefore, fractional dynamics leads to time responses with super-fast transients and super-slow evolutions towards the steady-state, effects not easily captured by the integer order models.

ASSOCIATION BETWEEN SMOKING, CRACK COCAINE ABUSE AND THE DISCONTINUATION OF COMBINATION ANTIRETROVIRAL THERAPY IN RECIFE, PERNAMBUCO, BRAZIL

Despite the effectiveness of combination antiretroviral therapy in the treatment of people living with HIV/AIDS (PLWHA), nonadherence to medication has become a major threat to its effectiveness. This study aimed to estimate the prevalence of self-reported irregular use of antiretroviral therapy and the factors associated with such an irregularity in PLWHA. A cross-sectional study of PLWHA who attended two referral centers in the city of Recife, in Northeastern Brazil, between June 2007 and October 2009 was carried out. The study analyzed socioeconomic factors, social service support and personal habits associated with nonadherence to antiretroviral therapy, adjusted by multivariable logistic regression analysis. The prevalence of PLWHA who reported irregular use of combination antiretroviral therapy (cART) was 25.7%. In the final multivariate model, the irregular use of cART was associated with the following variables: being aged less than 40 years (OR = 1.66, 95%-CI: 1.29-2.13), current smokers (OR = 1.76, 95%-CI: 1.31-2.37) or former smokers (OR = 1.43, 95%-CI: 1.05-1.95), and crack cocaine users (OR = 2.79, 95%-CI: 1.24-6.32). Special measures should be directed towards each of the following groups: individuals aged less than 40 years, smokers, former smokers and crack cocaine users. Measures for giving up smoking and crack cocaine should be incorporated into HIV-control programs in order to promote greater adherence to antiretroviral drugs and thus improve the quality of life and prolong life expectancy.

Estudo numérico da adequação de diferentes tipos de leis coesivas na previsão da resistência de juntas adesivas por Modelos de Dano Coesivo

O uso de ligações adesivas aumentou significativamente nos últimos anos e é hoje em dia uma técnica de ligação dominante na indústria aeronáutica e automóvel. As ligações adesivas visam substituir os métodos tradicionais de fixação mecânicos na união de estruturas. A melhoria ao longo dos anos de vários modelos de previsão de dano, nomeadamente através do Método de Elementos Finitos (MEF), tem ajudado ao desenvolvimento desta técnica de ligação. Os Modelos de Dano coesivo (MDC), usados em conjunto com MEF, são uma ferramenta viável para a previsão de resistência de juntas adesivas. Os MDC combinam critérios da resistência dos materiais para a iniciação do dano e conceitos da mecânica da fratura para a propagação da fenda. Existem diversas formas de leis coesivas possíveis de aplicar em simulações por MDC, em função do comportamento expectável dos materiais que estão a ser simulados. Neste trabalho, estudou-se numericamente o efeito de diversas formas de leis coesivas na previsão no comportamento de juntas adesivas, nomeadamente nas curvas forçadeslocamento (P-) de ensaios Double-Cantilever Beam para caracterização à tração e ensaios End-Notched Flexure para caraterização ao corte. Também se estudou a influência dos parâmetros coesivos à tração e corte nas curvas P- dos referidos ensaios. Para o Araldite®AV138 à tração e ao corte, a lei triangular é a que melhor prevê o comportamento do adesivo. Para a previsão da resistência de ambos os adesivos Araldite® 2015 e SikaForce® 7752, a lei trapezoidal é a que melhor se adequa, confirmando assim que esta lei é a que melhor caracteriza o comportamento de dano de adesivos tipicamente dúcteis. O estudo dos parâmetros revelou influência distinta na previsão do comportamento das juntas, embora com bastantes semelhanças entre os diferentes tipos de adesivos.

Damage propagation in composite Materials meso-mechanical models

Composite materials have a complex behavior, which is difficult to predict under different types of loads. In the course of this dissertation a methodology was developed to predict failure and damage propagation of composite material specimens. This methodology uses finite element numerical models created with Ansys and Matlab softwares. The methodology is able to perform an incremental-iterative analysis, which increases, gradually, the load applied to the specimen. Several structural failure phenomena are considered, such as fiber and/or matrix failure, delamination or shear plasticity. Failure criteria based on element stresses were implemented and a procedure to reduce the stiffness of the failed elements was prepared. The material used in this dissertation consist of a spread tow carbon fabric with a 0°/90° arrangement and the main numerical model analyzed is a 26-plies specimen under compression loads. Numerical results were compared with the results of specimens tested experimentally, whose mechanical properties are unknown, knowing only the geometry of the specimen. The material properties of the numerical model were adjusted in the course of this dissertation, in order to find the lowest difference between the numerical and experimental results with an error lower than 5% (it was performed the numerical model identification based on the experimental results).

The influence of fibre orientation on the post-cracking tensile behaviour of steel fibre reinforced self-compacting concrete

Adding fibres to concrete provides several advantages, especially in terms of controlling the crack opening width and propagation after the cracking onset. However, distribution and orientation of the fibres toward the active crack plane are significantly important in order to maximize its benefits. Therefore, in this study, the effect of the fibre distribution and orientation on the post-cracking tensile behaviour of the steel fibre reinforced self-compacting concrete (SFRSCC) specimens is investigated. For this purpose, several cores were extracted from distinct locations of a panel and were subjected to indirect (splitting) and direct tensile tests. The local stress-crack opening relationship (σ-w) was obtained by modelling the splitting tensile test under the finite element framework and by performing an Inverse Analysis (IA) procedure. Afterwards the σ-w law obtained from IA is then compared with the one ascertained directly from the uniaxial tensile tests. Finally, the fibre distribution/orientation parameters were determined adopting an image analysis technique.

A model to simulate the moment-rotation and crack width of FRC members reinforced with longitudinal bars

The present work describes a model for the determination of the moment–rotation relationship of a cross section of fiber reinforced concrete (FRC) elements that also include longitudinal bars for the flexural reinforcement (R/FRC). Since a stress–crack width relationship (σ–w)(σ–w) is used to model the post-cracking behavior of a FRC, the σ–w directly obtained from tensile tests, or derived from inverse analysis applied to the results obtained in three-point notched beam bending tests, can be adopted in this approach. For a more realistic assessment of the crack opening, a bond stress versus slip relationship is assumed to simulate the bond between longitudinal bars and surrounding FRC. To simulate the compression behavior of the FRC, a shear friction model is adopted based on the physical interpretation of the post-peak compression softening behavior registered in experimental tests. By allowing the formation of a compressive FRC wedge delimited by shear band zones, the concept of concrete crushing failure mode in beams failing in bending is reinterpreted. By using the moment–rotation relationship, an algorithm was developed to determine the force–deflection response of statically determinate R/FRC elements. The model is described in detail and its good predictive performance is demonstrated by using available experimental data. Parametric studies were executed to evidence the influence of relevant parameters of the model on the serviceability and ultimate design conditions of R/FRC elements failing in bending.

Estratégias desenvolvidas por usuários de crack para lidar com os riscos decorrentes do consumo da droga

OBJETIVOS: O objetivo deste estudo foi identificar, sob a ótica de usuários de crack, quais são as estratégias que eles utilizam para minimizar ou evitar os riscos decorrentes do consumo de crack. MÉTODO: Utilizou-se método qualitativo de pesquisa, desenvolvido mediante entrevistas semiestruturadas em profundidade. Foi entrevistada uma amostra intencional por critérios, composta por 30 usuários de crack, selecionados por meio de informantes-chave e distribuídos em oito diferentes cadeias. As entrevistas foram transcritas literalmente, inseridas e analisadas no software NVivo 8, com exploração dos dados mediante a técnica de análise de conteúdo. RESULTADOS: Os entrevistados acreditam que os maiores riscos decorrentes da dependência do crack sejam os relacionados aos efeitos psíquicos da droga, como fissura, sintomas paranoides transitórios e sintomas depressivos, assim como os decorrentes da ilegalidade dela, como a polícia e as questões referentes ao tráfico. Entretanto, os riscos de complicações físicas do consumo quase não foram apontados. As estratégias se concentraram no controle dos efeitos psíquicos, principalmente pelo consumo de álcool e maconha. Para lidar com as consequências da ilegalidade da droga, mostraram se preocupar com a postura que adotam perante o traficante e a polícia. CONCLUSÕES: As estratégias desenvolvidas pelos usuários focam na tentativa de se autoprotegerem principalmente dos episódios de violência e no alívio de sintomas desagradáveis causados pela droga - principalmente fissura e sintomas paranoides transitórios. Essas estratégias podem parecer efetivas a curto prazo, porém apresentaram riscos de longo prazo, tais como dependência de álcool e maconha.

Relação entre o craving por tabaco e o craving por crack em pacientes internados para desintoxicação

OBJETIVO: Verificar se há relação entre aumento do craving por crack e aumento do craving por tabaco em pacientes internados para desintoxicação. MÉTODO: Ensaio clínico tipo quase-experimental de análise quantitativa. Amostra composta por 32 homens dependentes de cocaína (crack) e tabaco, em duas a três semanas de abstinência. Realizou-se intervenção em grupo, no qual, inicialmente, foram aplicados: CCQB (Cocaine Craving Questionnaire-Brief ), QSUB (Questionnaire of Smoking Urges-Brief ) e BAI (Inventário Beck de Ansiedade). Em seguida, foram aplicadas imagens relacionadas ao crack e reaplicados CCQB, QSUB e BAI. Após, foi realizada entrevista individual em que se aplicaram FSD (Ficha com Dados Sociodemográficos) e FTND (Fagerström Test for Nicotine Dependence). RESULTADOS: A partir da exposição de imagens relativas ao crack, houve aumento significativo do craving por crack, do craving por tabaco e dos sintomas de ansiedade, estando essas medidas correlacionadas positivamente entre si. CONCLUSÃO: Os resultados indicam uma associação significativa entre craving por crack e craving por tabaco, sugerindo que a abstinência de tabaco pode ajudar na eficácia do tratamento para dependência de crack.

Associação entre fissura e perfil antropométrico em dependentes de crack

OBJETIVO: Verificar a variação da fissura de dependentes de crack no decorrer da internação e a associação com perfil antropométrico. MÉTODOS: Trata-se de uma pesquisa quantitativa com delineamento transversal (n = 30). Avaliaram-se o perfil de consumo de substâncias psicoativas; dados sociodemográficos; variáveis antropométricas (peso, estatura, índice de massa corporal, relação cintura-quadril, perímetros, dobras cutâneas e diâmetro ósseo); e fissura avaliada por meio do Cocaine Craving Questionnaire Brief. As coletas de dados ocorreram nas 24 horas iniciais e finais do tratamento. RESULTADOS: Observou-se aumento significativo do percentual de gordura e diminuição significativa da fissura. Não se evidenciou associação entre variáveis antropométricas e fissura, tanto no início como ao final da internação. CONCLUSÃO: Houve significativa diminuição na fissura e modificação na composição corporal, entretanto não houve correlação entre essas variáveis.