Annealing effects on strain and stress sensitivity of polymer optical fibre based sensors

The annealing effects on strain and stress sensitivity of polymer optical fibre Bragg grating sensors after their photo-inscription are investigated. PMMA optical fibre based Bragg grating sensors are first photo-inscribed and then they were placed into hot water for annealing. Strain, stress and force sensitivity measurements are taken before and after annealing. Parameters such as annealing time and annealing temperature are investigated. The change of the fibre diameter due to water absorption and the annealing process is also considered. The results show that annealing the polymer optical fibre tends to increase the strain, stress and force sensitivity of the photo-inscribed sensor.

Humidity sensitivity of topas optical fibre bragg grating

Fibre Bragg gratings at 1568nm have been inscribed in single mode TOPAS microstructured polymer optical fibre to characterise thermal and humidity sensitivity of the fibres in the 1550nm spectral region. Results demonstrate a temperature sensitivity of approximately -36 pm/°C and a humidity sensitivity of no more than - 0.59 pm/%RH. The fibre material appears to be very attractive for long term monitoring of high strains because of its insensitivity to humidity.

Sensitivity enhancement using annealed polymer optical fibre based sensors for pressure sensing applications

Thermal annealing can be used to induce a permanent negative Bragg wavelength shift for polymer fibre grating sensors and it was originally used for multiplexing purposes. Recently, researchers showed that annealing can also provide additional benefits, such as strain and humidity sensitivity enhancement and augmented temperature operational range. The annealing process can change both the optical and mechanical properties of the fibre. In this paper, the annealing effects on the stress and force sensitivities of PMMA fibre Bragg grating sensors are investigated. The incentive for that investigation was an unexpected behaviour observed in an array of sensors which were used for liquid level monitoring. One sensor exhibited much lower pressure sensitivity and that was the only one that was not annealed. To further investigate the phenomenon, additional sensors were photo-inscribed and characterised with regard their stress and force sensitivities. Then, the fibres were annealed by placing them in hot water, controlling with that way the humidity factor. After annealing, stress and force sensitivities were measured again. The results show that the annealing can improve the stress and force sensitivity of the devices. This can provide better performing sensors for use in stress, force and pressure sensing applications.

3D printed sensing patches with embedded polymer optical fibre Bragg gratings

The first demonstration of a polymer optical fibre Bragg grating (POFBG) embedded in a 3-D printed structure is reported. Its cyclic strain performance and temperature characteristics are examined and discussed. The sensing patch has a repeatable strain sensitivity of 0.38 pm/μepsilon. Its temperature behaviour is unstable, with temperature sensitivity values varying between 30-40 pm/°C.

Aviation fuel gauging sensor utilizing multiple diaphragm sensors incorporating polymer optical fiber Bragg gratings

A high-performance fuel gauging sensor is described that uses five diaphragm-based pressure sensors, which are monitored using a linear array of polymer optical fiber Bragg gratings. The sensors were initially characterized using water, revealing a sensitivity of 98 pm/cm for four of the sensors and 86 pm/cm for the fifth. The discrepancy in the sensitivity of the fifth sensor has been explained as being a result of the annealing of the other four sensors. Initial testing in JET A-1 aviation fuel revealed the unsuitability of silicone rubber diaphragms for prolonged usage in fuel. A second set of sensors manufactured with a polyurethane-based diaphragm showed no measurable deterioration over a three month period immersed in fuel. These sensors exhibited a sensitivity of 39 pm/cm, which is less than the silicone rubber devices due to the stiffer nature of the polyurethane material used.

Formazione delle galassie e cenni sulla loro evoluzione

In questa tesi si vuole fornire una panoramica generale dei processi di formazione delle galassie, con l'aggiunta di alcuni cenni sulla loro evoluzione. Nel primo capitolo si danno alcune informazioni sulla natura di questi oggetti e su come è stata scoperta la loro esistenza. Poi, utilizzando le premesse di cui al capitolo 2, nel capitolo 3 si passa alla spiegazione della loro formazione a partire dagli eventi successivi al Big Bang, di cui si fornisce una breve cronologia. Nel capitolo 4 si dà una panoramica della formazione degli ammassi di galassie e si discute di alcune osservazioni compiute su di essi, per concludere con considerazioni sul loro futuro. Infine, nell'ultimo capitolo ci si concentra sull'evoluzione delle galassie, in particolare sui processi di merging e sulle collisioni.

Indicators on community art practices: some reflections

From the Divercity project, the article reflects on methodology, good practices and indicators useful for community art practices. At first term, social exclusión is defined as well as community art, and which features it presents. Subsequently, the article reviews the indicators that are being used to measure the success or achievement of community arts practice, raising criticism from equality and including indicators that measure the well-being of women.

Sternoclavicular Septic Arthritis Caused by Acupuncture over the Posterior Neck

Acupuncture has been used therapeutically for thousands of years and is considered a relatively safe procedure. Sternoclavicular joint (SCJ) arthritis is a rare joint infection and has never been reported as an adverse event of acupuncture. We report the case of a 50-year-old woman who presented with progressive left neck, shoulder and upper chest pain after acupuncture. A computerized tomography (CT) scan revealed septic arthritis over the left sternoclavicular joint (SCJ) and methicillin-sensitive Staphylococcus aureus bacteraemia was noted. The patient was discharged uneventfully after intravenous antibiotic treatment. SCJ septic arthritis should be considered if unilateral neck and upper chest pain occurs after acupuncture.

Cosmologia e astrofísica no ensino secundário

Dissertação de mest. em Física - área de especialização em Física para Ensino, Faculdade de Ciências e Tecnologia, Univ. do Algarve, 2003

Fuel level sensor based on polymer optical fiber Bragg gratings for aircraft applications

Safety in civil aviation is increasingly important due to the increase in flight routes and their more challenging nature. Like other important systems in aircraft, fuel level monitoring is always a technical challenge. The most frequently used level sensors in aircraft fuel systems are based on capacitive, ultrasonic and electric techniques, however they suffer from intrinsic safety concerns in explosive environments combined with issues relating to reliability and maintainability. In the last few years, optical fiber liquid level sensors (OFLLSs) have been reported to be safe and reliable and present many advantages for aircraft fuel measurement. Different OFLLSs have been developed, such as the pressure type, float type, optical radar type, TIR type and side-leaking type. Amongst these, many types of OFLLSs based on fiber gratings have been demonstrated. However, these sensors have not been commercialized because they exhibit some drawbacks: low sensitivity, limited range, long-term instability, or limited resolution. In addition, any sensors that involve direct interaction of the optical field with the fuel (either by launching light into the fuel tank or via the evanescent field of a fiber-guided mode) must be able to cope with the potential build up of contamination-often bacterial-on the optical surface. In this paper, a fuel level sensor based on microstructured polymer optical fiber Bragg gratings (mPOFBGs), including poly (methyl methacrylate) (PMMA) and TOPAS fibers, embedded in diaphragms is investigated in detail. The mPOFBGs are embedded in two different types of diaphragms and their performance is investigated with aviation fuel for the first time, in contrast to our previous works, where water was used. Our new system exhibits a high performance when compared with other previously published in the literature, making it a potentially useful tool for aircraft fuel monitoring.

Embedding silica and polymer fibre Bragg gratings (FBG) in plastic 3D-printed sensing patches

This paper reports the first demonstration of a silica fibre Bragg grating (SOFBG) embedded in an FDM 3-D printed housing to yield a dual grating temperature-compensated strain sensor. We also report the first ever integration of polymer fibre Bragg grating (POFBG) within a 3-D printed sensing patch for strain or temperature sensing. The cyclic strain performance and temperature characteristics of both devices are examined and discussed. The strain sensitivities of the sensing patches were 0.40 and 0.95 pm/μϵ for SOFBG embedded in ABS, 0.38 pm/μμ for POFBG in PLA, and 0.15 pm/μμ for POFBG in ABS. The strain response was linear above a threshold and repeatable. The temperature sensitivity of the SOFBG sensing patch was found to be up to 169 pm/°C, which was up to 17 times higher than for an unembedded silica grating. Unstable temperature response POFBG embedded in PLA was reported, with temperature sensitivity values varying between 30 and 40 pm/°C.

Cáncer gástrico en pacientes de Méderi – Hospital Universitario Mayor entre los años 2011 - 2014

Introducción: El cáncer gástrico es uno de los más frecuentes a nivel mundial y Colombia se sitúa entre los países de mayor incidencia en este tipo de patología. Objetivo: Describir las características epidemiológicas, clínicas, el tratamiento administrado y los desenlaces inmediatos de los pacientes con diagnóstico de cáncer gástrico atendidos en el Hospital Universitario Mayor de Bogotá entre los años 2011 y 2014. Metodología: Se realizó un estudio observacional descriptivo con diagnóstico de cáncer gástrico. Se realizaron análisis univariados por medio de proporciones para las variables cualitativas y medidas de tendencia central para las variables cuantitativas según la distribución. Resultados: Un total de 189 pacientes fueron analizados. El dolor fue el síntoma más frecuente en los pacientes (30.7%) y el principal signo encontrado fue una masa palpable en abdomen (9,5%). Los pacientes fueron sometidos a diferentes abordajes terapéuticos, la mayoría recibieron manejo paliativo no quirúrgico (52.9%) y la opción quirúrgica más usada en los pacientes fue la gastrectomía total (20.6%), y la subtotal (16,4) seguidas de quimioterapia y/o radiación perioperatoria. Los pacientes que sobrevivieron a los 2 años fueron 7,4% del total. Conclusiones: El registro de los pacientes con cáncer gástrico es bueno en el Méderi-Hospital Universitario Mayor es bueno y permite caracterizar los pacientes, la presentación de la patología y los resultados del tratamiento que concuerdan con los presentados en contextos similares en la literatura.

Revisión sistemática de la literatura de las intervenciones diseñadas para el comportamiento de automedicación no responsable

La automedicación no responsable se ha convertido en un problema de salud pública global en las últimas décadas, por sus consecuencias individuales (por ejemplo, la intoxicación) y colectivas (por ejemplo, la resistencia microbiana a los antibióticos). Las intervenciones orientadas a este comportamiento han sido aisladas y muy diferentes. Aunque se tiene evidencia de que su aplicación puede traer beneficios en diferentes poblaciones, no se halló en la literatura una compilación sistemática de dichas intervenciones. El objetivo de la presente revisión es sistematizar la literatura científica sobre las diferentes alternativas de intervención del comportamiento individual de automedicación no responsable. En cuanto al método, la revisión de literatura involucró la búsqueda sistemática de “automedicación” e “intervención” en las bases de datos académicas internacionales con contenidos de psicología, suscritas por la Biblioteca de la Universidad del Rosario. Como resultado se encontró que las intervenciones orientadas al comportamiento de automedicación no responsable se pueden clasificar en dos grandes grupos: (a) intervenciones regulatorias, con dirección “arriba hacia abajo”, que suponen una acción de los Estados nacionales por medio de sus legislaciones o de entidades internacionales (por ejemplo, Organización Mundial de la Salud); y (b) intervenciones educativas, con dirección “abajo hacia arriba”, que suponen acciones con individuos y comunidades con el fin de enseñar acerca del uso adecuado de los medicamentos. Se concluye acerca de la necesidad de complementar ambos tipos de intervención, los cuales, si bien demuestran resultados positivos, aisladamente son insuficientes para contrarrestar integralmente este fenómeno creciente y complejo.

A pointwise constrained version of the Liapunov convexity theorem for vectorial linear first-order control systems

We generalize the Liapunov convexity theorem's version for vectorial control systems driven by linear ODEs of first-order p = 1 , in any dimension d ∈ N , by including a pointwise state-constraint. More precisely, given a x ‾ ( ⋅ ) ∈ W p , 1 ( [ a , b ] , R d ) solving the convexified p-th order differential inclusion L p x ‾ ( t ) ∈ co { u 0 ( t ) , u 1 ( t ) , … , u m ( t ) } a.e., consider the general problem consisting in finding bang-bang solutions (i.e. L p x ˆ ( t ) ∈ { u 0 ( t ) , u 1 ( t ) , … , u m ( t ) } a.e.) under the same boundary-data, x ˆ ( k ) ( a ) = x ‾ ( k ) ( a ) & x ˆ ( k ) ( b ) = x ‾ ( k ) ( b ) ( k = 0 , 1 , … , p − 1 ); but restricted, moreover, by a pointwise state constraint of the type 〈 x ˆ ( t ) , ω 〉 ≤ 〈 x ‾ ( t ) , ω 〉 ∀ t ∈ [ a , b ] (e.g. ω = ( 1 , 0 , … , 0 ) yielding x ˆ 1 ( t ) ≤ x ‾ 1 ( t ) ). Previous results in the scalar d = 1 case were the pioneering Amar & Cellina paper (dealing with L p x ( ⋅ ) = x ′ ( ⋅ ) ), followed by Cerf & Mariconda results, who solved the general case of linear differential operators L p of order p ≥ 2 with C 0 ( [ a , b ] ) -coefficients. This paper is dedicated to: focus on the missing case p = 1 , i.e. using L p x ( ⋅ ) = x ′ ( ⋅ ) + A ( ⋅ ) x ( ⋅ ) ; generalize the dimension of x ( ⋅ ) , from the scalar case d = 1 to the vectorial d ∈ N case; weaken the coefficients, from continuous to integrable, so that A ( ⋅ ) now becomes a d × d -integrable matrix; and allow the directional vector ω to become a moving AC function ω ( ⋅ ) . Previous vectorial results had constant ω, no matrix (i.e. A ( ⋅ ) ≡ 0 ) and considered: constant control-vertices (Amar & Mariconda) and, more recently, integrable control-vertices (ourselves).