Amorphous boron-silicon-hydrogen alloys for thin films heterojunction solar-cell : quarterly technical progress report no. 1 for June 1 - August 31, 1970 /

"Work Performed Under Contract No. AC02-77CH00178."

Nuclear safety measurements on systems containing boron and enriched uranium /

"U.S. Atomic Energy Commission Contract AT(29-1)-1106."

Corrosion studies on 304 stainless steel containing one percent boron-10 /

"U.S. Atomic Energy Commission Contract AT(29-1)-1106."

Boron /

Work done by the National Bureau of Standards, Washington, D.C.

Boron in agriculture.

Includes bibliographical references.

Nuclear safety experiments on plutonium and enriched uranium hydrogen moderated assemblies containing boron /

"Date Distributed: October 13, 1960."

Plasma torch production of elemental boron

On cover: AEC research and development report.

Boron trifluoride and its derivatives /

References: p. 256-290.

(Table 3) Boron and chlorine in atmospheric moisture and rain water collected on the shore of the Golubaya Bay in 1970

Boron and chlorine were determined in rain water and in atmospheric moisture condensed in a "Saratov" refrigerator. Ocean is the main source of boron on the earth surface. Boron evaporates from the ocean and enriches atmospheric precipitation: B/Cl ratio of ocean water (0.00024) increases by factor of 10-15. Assuming that the average Cl content in global river runoff is 7.8 mg/l and boron content 0.013 mgl, B/Cl ratio in this runoff is 0.0017. The average B/Cl ratio in rain water of the Golubaya (Blue) Bay (Gelendzhik, Black Sea region) is 0.0026 and in condensates of atmospheric moisture during onshore and offshore winds in the same region it averages from 0.0029 to 0.0033. The maximum boron content in the condensates of this region during onshore winds was 0.032 mg/l and the minimum during offshore winds, 0.004 mg/l. /Cl ratio in sea water over the Atlantic Ocean and in the Gelendzhik area of the Black Sea varied within narrow range, mostly from 0.0025 to 0.0035. Similar B/Cl ratio (0.0024) was found for atmospheric precipitation on the slope of the Terskei Ala-Tau near the Issyk-Kul Lake in 1969. Thus, although chemistries of boron and chlorine (in chlorides) are very different, the B/Cl ratio in the atmosphere is fairly constant. This can be taken as a confirmation of an assumption that salt composition of sea water passes into the atmosphere in molecularly dispersed state. Supposing that the ocean-atmosphere system is in equilibrium as regards to the boron budget, it can be assumed that the same amount of boron passes from the ocean into bottom sediments and from lithosphere rocks and soils into the hydrosphere.

Effects of boron foliar applications on vegetative and reproductive growth of sunflower

Foliar application may be used to supply boron (B) to a crop when B demands are higher than can be supplied via the soil. While B foliar sprays have been used to correct B deficiency in sunflower (Helianthus annuus L.) in the field, no studies have determined the amount of B taken up by sunflower plant parts via foliar application. A study was conducted in which sunflower plants were grown at constant B concentration in nutrient solution with adequate B (46 mum) or with limited B supply (0.24, 0.40 and 1.72 mum) using Amberlite IRA-743 resin to control B supply. At the late vegetative stage of growth (25 and 35 d after transplanting), two foliar sprays were applied of soluble sodium tetraborate (20.8 % B) each at 0, 28, 65, 120 and 1200 mm (each spray equivalent to 0, 0.03, 0.07, 0.13 and 1.3 kg B ha(-1) in 100 L water ha(-1)). The highest rate of B foliar fertilization resulted in leaf burn but had no other evident detrimental effect on plant growth. Under B-deficient conditions, B foliar application increased the vegetative and reproductive dry mass of plants. Foliar application of 28-1200 mm B increased the total dry mass of the most B-deficient plants by more than three-fold and that of plants grown initially with 1.72 mum B in solution by 37-49 %. In this latter treatment, the dry mass of the capitulum was similar to that achieved under control conditions, but in no instance was total plant dry mass similar to that of the control. All B foliar spray rates increased the B concentration in various parts of the plant tops, including those that developed after the sprays were applied, but the B concentration in the roots was not increased by B foliar application. The B concentration in the capitulum of the plants sprayed at the highest rate was between 37 and 93 % of that in the control plants. This study showed that B foliar application was of benefit to B-deficient sunflower plants, increasing the B status of plant tops, including that of the capitulum which developed after the B sprays were applied. (C) 2003 Annals of Botany Company.

Effects of boron-strontium interactions on eutectic modification in Al-10 mass%Si alloys

The effects of boron and strontium interactions on the eutectic silicon in hypoeutectic Al-Si alloys have been studied. Samples were prepared from an AI-I 0 mass%Si base alloy with different Al-B additions, alone and in combination with strontium. In alloys containing no strontium, boron additions do not cause modification of the eutectic silicon, while in strontium containing alloys, boron additions reduce the level of modification of the eutectic silicon. Thermal analysis parameters and eutectic silicon microstructures were investigated with respect to the Sr to B ratio. In order to modify the eutectic silicon, a Sr/B ratio exceeding 0.4 is required.

Effects of boron on eutectic modification of hypoeutectic Al-Si alloys

The effects of boron on the eutectic modification and solidification mode of hypoeutectic Al-Si alloys have been studied adding different boride phases. The results show that boron does not cause modification of the eutectic silicon. Boron-containing samples display eutectic nucleation and growth characteristics similar to that of unmodified alloys. (C) 2002 Acta Materialia Inc. Published by Elsevier Science Ltd. All rights reserved.

Boron solubility in Fe-Cr-B cast irons

Boron solubility in the as-cast and solution treated martensite of Fe-Cr-B cast irons, containing approximately 1.35 wt.% of boron, 12 wt.% of chromium, as well as other alloying elements, has been investigated using conventional microanalysis. The significant microstructural variations after tempering at 750 degreesC for 0.5-4 h, compared with the original as-cast and solution treated microstructures, indicated that the matrix consisted of boron and carbon supersaturated solid solutions. The boron solubility detected by electron microprobe was between 0.185-0.515 wt.% for the as-cast martensite and 0.015-0.0589 wt.% for the solution treated martensite, much higher than the accepted value of 0.005 wt.% in pure iron. These remarkable increases are thought to be associated with some metallic alloying element addition, such as chromium, vanadium and molybdenum, which have atomic diameters larger than iron, and expand the iron lattice to sufficiently allow boron atoms to occupy the interstitial sites in iron lattice. (C) 2002 Elsevier Science B.V. All rights reserved.

Sintering of freeformed maraging steel with boron additions

This paper describes the sintering of an 18Ni(350) maraging steel with additions of boron, with the aim of producing high hardness rapid tooling. Reaction of the boron with the alloying elements in the maraging steel resulted in the formation of a Mo- and Ti-rich borides. The former melted at similar to1220degreesC, providing a liquid phase for enhanced sintering. Although densification could occur regardless of the boron content, especially at high temperature, 0.4% B was required to produce a near full density component. The formation of the various borides depleted the matrix of critical age hardening elements. However, by altering the starting powder composition to compensate for this, hardness close to the wrought alloy has been achieved. This hardness was comparable to a common die casting tool steel. Examples of dies produced using selective laser sintering (SLS) are also shown. (C) 2003 Elsevier B.V. All rights reserved.

Crystallography of zirconium hydrides in recrystallized Zircaloy-2 fuel cladding lay electron backscatter diffraction

Precipitation morphology and habit planes of the delta-phase Zr hydrides, which were precipitated within the a-phase matrix grains and along the grain boundaries of recrystallized Zircaloy-2 cladding tube, have been examined by electron backscatter diffraction (EBSD). Radially-oriented hydrides, induced by residual tensile stress, precipitated in the outside region of the cladding, and circumferentially-oriented hydrides in the stress-free middle region of the cladding. The most common crystallographic relationship for both types of the hydrides precipitated at the inter- and intra-granular sites was identical at (0001)(alpha) // {111}(delta), with {1017}(alpha) // {111}(delta) being the occasional exception only for the inter-granular radial hydrides. When tensile stress was loaded, the intra-granular hydrides tended to preferentially precipitate in the grains with circumferential basal pole textures. The inter-granular hydrides tended to preferentially precipitate on the grain faces opposite to tensile axis. The change of prioritization in the precipitation sites for the hydrides due to tensile stress could be explained in terms of the relaxation effect of constrained elastic energy on the terminal solid solubility of hydrogen at hydride precipitation.