Biological productivity and fishery potential in the coastal waters off Bombay

Fishery potential of the nearshore waters of Bombay is estimated from the observed values of biological productivity at different trophic levels. The rate of primary and secondary production is relatively higher in the polluted coastal waters of Versova, Mahim and Thana. Observed mean benthic standing stock in the polluted creek waters is far less than the relatively unpolluted coastal regions off Bombay. Results suggest that the higher productivity at the lower trophic levels due to pollution, may not end up with high tertiary production. Therefore, such polluted regions are to be classified as special ecosystems where the transfer coefficient may be far less than the assumed 10% conversion factor.

Wake, shock and potential field interactions in a 1.5 stage turbine: Part I: Vane-rotor and rotor-vane interaction

The composition of the time-resolved surface pressure field around a high-pressure rotor blade caused by the presence of neighboring blade rows was studied, with the individual effects of wake, shock and potential field interaction being determined. Two test geometries were considered: first, a high-pressure turbine stage coupled with a swan-necked diffuser exit duct; secondly, the same high-pressure stage but with a vane located in the downstream duct. Both tests were carried out at engine-representative Mach and Reynolds numbers. By comparing the results to time-resolved computational predictions of the flowfield, the accuracy with which the computation predicts blade interaction was determined. It was found that in addition to upstream vane-rotor and rotor-downstream vane interactions, a new interaction mechanism was found resulting from the interaction between the downstream vane's potential field and the upstream vane's trailing edge potential field and shock.

Wake, shock and potential field interactions in a 1.5 stage turbine: Part II: Vane-vane interaction and discussion of results

The composition of the time-resolved surface pressure field around a high-pressure rotor blade caused by the presence of neighboring blade rows was studied, with the individual effects of wake, shock and potential field interaction being determined. Two test geometries were considered: first, a high-pressure turbine stage coupled with a swan-necked diffuser exit duct; secondly, the same high-pressure stage but with a vane located in the downstream duct. Both tests were carried out at engine-representative Mach and Reynolds numbers. By comparing the results to time-resolved computational predictions of the flowfield, the accuracy with which the computation predicts blade interaction was determined. Evidence was obtained that for a large downstream vane, the flow conditions in the rotor passage, at any instant in time, are close to being steady state.

Cloning of bradykinin precursor cDNAs from skin of Bombina maxima reveals novel bombinakinin M antagonists and a bradykinin potential peptide

Bombinakinin M (DLPKINRKGP-bradykinin) is a bradykinin-related peptide purified from skin secretions of the frog Bombina maxima. As previously reported, its biosynthesis is characterized by a tandem repeats with various copy numbers of the peptide and sometimes co-expressed with other structure-function distinguishable peptides. At present study, two novel cDNAs encoding bombinakinin M and its variants were cloned from a cDNA library from the skin of the frog. The encoded two precursor proteins are common in that each contains three repeats of a novel 16-amino acid peptide unit and one copy of kinestatin at their N- and C-terminal parts, respectively. They differ in that the first precursor contains two copies of bombinakinin M and the second one contains one copy of a novel bombinakinin M variant. Bombinakinin M was found to elicit concentration-dependent contractile effects on guinea pig ileum, with an EC50 value of 4 nM that is four times higher than that of bradykinin (1 nM). Interestingly, the synthetic peptide (DYTIRTRLH-amide), as deduced from the 16-amino acid peptide repeats in the newly cloned cDNAs, possessed weak inhibitory activity on the contractile effects of bombinakinin M, but not on that of bradykinin. Furthermore, the newly identified bombinakinin M variant (DLSKMSFLHG-Ile(1)-bradykinin), did not show contractile activity on guinea pig ileum, but showed potentiation effect on the myotropic activity of bradykinin. In a molar raito of 1:58, it augmented the activity of bradykinin up to two-fold. (C) 2004 Elsevier B.V. All rights reserved.

Assessing the potential of yield improvements, through process scrap reduction, for energy and CO2 abatement in the steel and aluminium sectors

Targets to cut 2050 CO2 emissions in the steel and aluminium sectors by 50%, whilst demand is expected to double, cannot be met by energy efficiency measures alone, so options that reduce total demand for liquid metal production must also be considered. Such reductions could occur through reduced demand for final goods (for instance by life extension), reduced demand for material use in each product (for instance by lightweight design) or reduced demand for material to make existing products. The last option, improving the yield of manufacturing processes from liquid metal to final product, is attractive in being invisible to the final customer, but has had little attention to date. Accordingly this paper aims to provide an estimate of the potential to make existing products with less liquid metal production. Yield ratios have been measured for five case study products, through a series of detailed factory visits, along each supply chain. The results of these studies, presented on graphs of cumulative energy against yield, demonstrate how the embodied energy in final products may be up to 15 times greater than the energy required to make liquid metal, due to yield losses. A top-down evaluation of the global flows of steel and aluminium showed that 26% of liquid steel and 41% of liquid aluminium produced does not make it into final products, but is diverted as process scrap and recycled. Reducing scrap substitutes production by recycling and could reduce total energy use by 17% and 6% and total CO 2 emissions by 16% and 7% for the steel and aluminium industries respectively, using forming and fabrication energy values from the case studies. The abatement potential of process scrap elimination is similar in magnitude to worldwide implementation of best available standards of energy efficiency and demonstrates how decreasing the recycled content may sometimes result in emission reductions. Evidence from the case studies suggests that whilst most companies are aware of their own yield ratios, few, if any, are fully aware of cumulative losses along their whole supply chain. Addressing yield losses requires this awareness to motivate collaborative approaches to improvement. © 2011 Elsevier B.V. All rights reserved.

The technical potential for reducing metal requirements through lightweight product design

Metal production consumes around 10% of all global energy, so is a significant driver of climate change and other concerns about sustainability. Demand for metal is rising and forecast to double by 2050 through a combination of growing total demand from developing countries, and ongoing replacement demand in developed economies. Metal production is already extremely efficient, so the major opportunities for emissions abatement in the sector are likely to arise from material efficiency - using less new metal to meet demand for services. Therefore this paper examines the opportunity to reduce requirements for steel and aluminium by lightweight design. A set of general principles for lightweight design are proposed by way of a simple analytical example, and are then applied to five case study products which cumulatively account for 30% of global steel product output. It is shown that exploiting lightweight design opportunities for these five products alone could reduce global steel requirements by 5%, and similar savings in aluminium products could reduce global aluminium requirements by 7%. If similar savings to those in the design case studies were possible in all steel and aluminium products, total material requirements could be reduced by 25-30%. However, many of these light-weighting measures are, at present, economically unattractive, and may take many years to implement. © 2011 Elsevier B.V. All rights reserved.

The potential for further proliferation of water hyacinth in Lakes Victoria, Kyoga and Kwania and some urgent aspects for research

Shore environments of Lakes Victoria and Kyoga with potential for the establishment and proliferation of water hyacinth were identified. They are characterised by: (i) shelter from violent off-shore and along-the-shore wind and wave action (ii) flat or gentle slope under relatively shallow water, and (iii) a muddy bottom rich in organic matter. Such environments are strongly associated with emergent macrophytes of papyrus, Vossia sp and, at times Typha sp where Pistia stratiotes, species of ceratophyllum, myriophylum and nymphaea also occur. In Lake Kyoga association with Vossia sp facilitated establishment of water hyacinth even along wind-swept shores and promoted extension of mats of the two machrophytes into the open lake. Urgent research on water hyacinth is proposed in the areas of nutrient relations, weed biology and on its impact on the biodiversity resource, with particular emphasis on the fishery component. Findings from the research could facilitate formulation of weed control options and alternative resource management strategies. A regional approach to address the water hyacinth menace is highly recommended.

The potential of Nakivubo swamp (papyrus wetland) in maintaining water quality of inner Murchison bay - Lake Victoria

Nakivubo swamp (papyrus wetland) is located in the south east of the city of Kampala, Uganda. This swamp has been receiving waste water from Nakivubo channel for more than two decades. This investigation was aimed at monitoring the level of pollutants (nutrients and faecal coliforms) as the waste water filtrates through the swamp and the flow patterns of waste water through the swamp. From this preliminary investigation it was found out that the waste water is not evenly distributed over the swamp. Also high levels of pollutants seem to filtrate through the swamp and enter Inner Murchison Bay - Lake Victoria. Further research is under way to investigate in more detail the capacity of Nakivubo swamp to remove nutrients/pollutants from waste water flowing through it and the dominant mechanisms/processes involved.

A global assessment of manufacturing: Economic development, energy use, carbon emissions, and the potential for energy efficiency and materials recycling

We present in two parts an assessment of global manufacturing. In the first part, we review economic development, pollution, and carbon emissions from a country perspective, tracking the rise of China and other developing countries. The results show not only a rise in the economic fortunes of the newly industrializing nations, but also a significant rise in global pollution, particularly air pollution and CO2 emissions largely from coal use, which alter and even reverse previous global trends. In the second part, we change perspective and quantitatively evaluate two important technical strategies to reduce pollution and carbon emissions: energy efficiency and materials recycling. We subdivide the manufacturing sector on the basis of the five major subsectors that dominate energy use and carbon emissions: (a) iron and steel, (b) cement, (c) plastics, (d) paper, and (e) aluminum. The analysis identifies technical constraints on these strategies, but by combined and aggressive action, industry should be able to balance increases in demand with these technical improvements. The result would be high but relatively flat energy use and carbon emissions. The review closes by demonstrating the consequences of extrapolating trends in production and carbon emissions and suggesting two options for further environmental improvements, materials efficiency, and demand reduction. © 2013 by Annual Reviews. All rights reserved.

Thermo-optical characterization of fluorescent rhodamine B based temperature-sensitive nanosensors using a CMOS MEMS micro-hotplate

A custom designed microelectromechanical systems (MEMS) micro-hotplate, capable of operating at high temperatures (up to 700 C), was used to thermo-optically characterize fluorescent temperature-sensitive nanosensors. The nanosensors, 550 nm in diameter, are composed of temperature-sensitive rhodamine B (RhB) fluorophore which was conjugated to an inert silica sol-gel matrix. Temperature-sensitive nanosensors were dispersed and dried across the surface of the MEMS micro-hotplate, which was mounted in the slide holder of a fluorescence confocal microscope. Through electrical control of the MEMS micro-hotplate, temperature induced changes in fluorescence intensity of the nanosensors was measured over a wide temperature range. The fluorescence response of all nanosensors dispersed across the surface of the MEMS device was found to decrease in an exponential manner by 94%, when the temperature was increased from 25 C to 145 C. The fluorescence response of all dispersed nanosensors across the whole surface of the MEMS device and individual nanosensors, using line profile analysis, were not statistically different (p < 0.05). The MEMS device used for this study could prove to be a reliable, low cost, low power and high temperature micro-hotplate for the thermo-optical characterisation of sub-micron sized particles. The temperature-sensitive nanosensors could find potential application in the measurement of temperature in biological and micro-electrical systems. The Authors. © 2013 Published by Elsevier B.V. All rights reserved.

Transfer, distribution and bioaccumulation of microcystins in the aquatic food web in Lake Taihu, China, with potential risks to human health

In this paper, accumulation and distribution of microcystins (MCs) was examined monthly in six species of fish with different trophic levels in Meiliang Bay, Lake Taihu, China, from June to November 2005, Microcystins were analyzed by liquid chromatography electrospray ionization mass spectrometry (LC-ESI-MS). Average recoveries of spiked fish samples were 67.7% for MC-RR, 85.3% for MC-YR, and 88.6% for MC-LR. The MCs (MC-RR+MC-YR+MC-LR) concentration in liver and gut content was highest in phytoplanktivorous fish, followed by omnivorous fish, and was lowest in carnivorous fish; while MCs concentration in muscle was highest in omnivorous fish, followed by phytoplanktivorous fish, and was lowest in carnivorous fish. This is the first study reporting MCs accumulation in the gonad of fish in field. The main uptake of MC-YR in fish seems to be through the gills from the dissolved MCs. The WHO limit for tolerable daily intake was exceeded only in common carp muscle. (C) 2008 Elsevier B.V. All rights reserved.

Molecular characterization and expression pattern of fetuin-B in gibel carp (Carassius auratus gibelio)

Fetuin-B has recently been cloned and identified from rats, mice, and humans; their expression patterns, however, have not been elucidated yet. In this study, Cagfetuin-B has been cloned in gibel carp. RT-PCR and Western blot detection revealed that Cagfetuin-B is first transcribed from the blastula stage and at a relatively stable level afterward during embryogenesis and the larval stage. Cagfetuin-B transcripts are predominantly distributed over the yolk syncytial layer in the early embryos and later restricted to the cells of liver and brain in newly hatched larvae. Moreover, a dynamic distribution of Cagfetuin-B protein was observed in brain, kidney, liver, and skin during morphogenesis. In adult fish, Cagfetuin-B transcripts are restricted in liver and ovary. Our work, for the first time, revealed the extra-hepatic transcription and a dynamic distribution of fetuin-B during embryogenesis and in adults, which indicates the potential roles of fetuin-B in fish organogenesis.