Development and mechanical characterization of solvent-cast polymeric films as potential drug delivery systems to mucosal surfaces

Solvent-cast films from three polymers, carboxymethylcellulose (CMC), sodium alginate (SA), and xanthan gum, were prepared by drying the polymeric gels in air. Three methods, (a) passive hydration, (b) vortex hydration with heating, and (c) cold hydration, were investigated to determine the most effective means of preparing gels for each of the three polymers. Different drying conditions [relative humidity - RH (6-52%) and temperature (3-45 degrees C)] were investigated to determine the effect of drying rate on the films prepared by drying the polymeric gels. The tensile properties of the CMC films were determined by stretching dumbbell-shaped films to breaking point, using a Texture Analyser. Glycerol was used as a plasticizer, and its effects on the drying rate, physical appearance, and tensile properties of the resulting films were investigated. Vortex hydration with heating was the method of choice for preparing gels of SA and CMC, and cold hydration for xanthan gels. Drying rates increased with low glycerol content, high temperature, and low relative humidity. The residual water content of the films increased with increasing glycerol content and high relative humidity and decreased at higher temperatures. Generally, temperature affected the drying rate to a greater extent than relative humidity. Glycerol significantly affected the toughness (increased) and rigidity (decreased) of CMC films. CMC films prepared at 45 degrees C and 6% RH produced suitable films at the fastest rate while films containing equal quantities of glycerol and CMC possessed an ideal balance between flexibility and rigidity.

AN INVESTIGATION OF THE EFFECTS OF SOME PROCESS VARIABLES ON THE MICROENCAPSULATION OF PROPRANOLOL HYDROCHLORIDE BY THE SOLVENT EVAPORATION METHOD

The effects of four process factors: pH, emulsifier (gelatin) concentration, mixing and batch, on the % w/w entrapment of propranolol hydrochloride in ethylcellulose microcapsules prepared by the solvent evaporation process were examined using a factorial design. In this design the minimum % w/w entrapments of propranolol hydrochloride were observed whenever the external aqueous phase contained 1.5% w/v gelatin at pH 6.0 (0.71-0.91% w/w) whereas maximum entrapments occurred whenever the external aqueous phase was composed of 0.5% w/v gelatin at pH 9.0,(8.9-9.1% w/w). The theoretical maximum loading was 50% w/w. Statistical evaluation of the results by analysis of variance showed that emulsifer (gelatin) concentration and pH, but not mixing and batch significantly affected entrapment. An interaction between pH and gelatin concentration was observed in the factorial design which was accredited to the greater effect of gelatin concentration on % w/w entrapment at pH 9.0 than at pH 6.0. Maximum theoretical entrapment was achieved by increasing the pH of the external phase to 12.0. Marked increases in drug entrapment were observed whenever the pH of the external phase exceeded the pK(2) of propranolol hydrochloride. It was concluded that pH, and hence ionisation, was the greatest determinant of entrapment of propranolol hydrochloride into microcapsules prepared by the solvent evaporation process.

The effect of polymer coatings on physicochemical properties of spray-dried liposomes for nasal delivery of BSA

This work describes the development of spray dried polymer coated liposomes composed of soy phosphatidylcholine (SPC) and phospholipid dimyristoyl phosphatidylglycerol (DMPG) coated with alginate, chitosan or trimethyl chitosan (TMC), that are able to penetrate through the nasal mucosa and offer enhanced penetration over uncoated liposomes when delivered as a dry powder. All the liposome formulations, loaded with BSA as model antigen, were spray-dried to obtain powder size and liposome size in a suitable range for nasal delivery. Although coating resulted in some reduction in encapsulation efficiency, levels were still maintained between 60% and 69% and the structural integrity of the entrapped protein and its release characteristics were maintained. Coating with TMC gave the best product characteristics in terms of entrapment efficiency, glass transition (Tg) and mucoadhesive strength, while penetration of nasal mucosal tissue was very encouraging when these liposomes were administered as dispersions although improved results were observed for the dry powders

Production and Processing of Spider Silk Proteins

Natural spider silk fibers have impressive mechanical properties (outperforming many man-made fibers) and are, moreover, biocompatible, biodegradable, and produced under benign conditions (using water as a solvent at ambient temperature). The problems associated with harvesting natural spider silks inspired us to devise a method to produce spider silk-like proteins biotechnologically (the first subject tackled in this highlight); we subsequently discuss their processing into various materials morphologies, and some potential technical and biomedical applications.

Gastroretentive Extended-Release Floating Granules Prepared Using a Novel Fluidized Hot Melt Granulation (FHMG) Technique

The objective of this work was to investigate the feasibility of using a novel granulation technique, namely, fluidized hot melt granulation (FHMG), to prepare gastroretentive extended-release floating granules. In this study we have utilized FHMG, a solvent free process in which granulation is achieved with the aid of low melting point materials, using Compritol 888 ATO and Gelucire 50/13 as meltable binders, in place of conventional liquid binders. The physicochemical properties, morphology, floating properties, and drug release of the manufactured granules were investigated. Granules prepared by this method were spherical in shape and showed good flowability. The floating granules exhibited sustained release exceeding 10 h. Granule buoyancy (floating time and strength) and drug release properties were significantly influenced by formulation variables such as excipient type and concentration, and the physical characteristics (particle size, hydrophilicity) of the excipients. Drug release rate was increased by increasing the concentration of hydroxypropyl cellulose (HPC) and Gelucire 50/13, or by decreasing the particle size of HPC. Floating strength was improved through the incorporation of sodium bicarbonate and citric acid. Furthermore, floating strength was influenced by the concentration of HPC within the formulation. Granules prepared in this way show good physical characteristics, floating ability, and drug release properties when placed in simulated gastric fluid. Moreover, the drug release and floating properties can be controlled by modification of the ratio or physical characteristics of the excipients used in the formulation.

Antimicrobial efficacy of tobramycin polymeric nanoparticles for Pseudomonas aeruginosa infections in cystic fibrosis: formulation, characterisation and functionalisation with dornase alfa (DNase).

Inhaled antibiotics, such as tobramycin, for the treatment of Pseudomonas aeruginosa pulmonary infections are associated with the increase in life expectancy seen in cystic fibrosis (CF) patients over recent years. However, the effectiveness of this aminoglycoside is still limited by its inability to penetrate the thick DNA-rich mucus in the lungs of these patients, leading to low antibiotic exposure to resident bacteria. In this study, we created novel polymeric nanoparticle (NP) delivery vehicles for tobramycin. Using isothermal titration calorimetry, we showed that tobramycin binds with alginate polymer and, by exploiting this interaction, optimised the production of tobramycin alginate/chitosan NPs. It was established that NP antimicrobial activity against P. aeruginosa PA01 was equivalent to unencapsulated tobramycin (minimum inhibitory concentration 0.625 mg/L). Galleria mellonella was employed as an in vivo model for P. aeruginosa infection. Survival rates of 90% were observed following injection of NPs, inferring low NP toxicity. After infection with P. aeruginosa, we showed that a lethal inoculum was effectively cleared by tobramycin NPs in a dose dependent manner. Crucially, a treatment with NPs prior to infection provided a longer window of antibiotic protection, doubling survival rates from 40% with free tobramycin to 80% with NP treatment. Tobramycin NPs were then functionalised with dornase alfa (recombinant human deoxyribonuclease I, DNase), demonstrating DNA degradation and improved NP penetration of CF sputum. Following incubation with CF sputum, tobramycin NPs both with and without DNase functionalisation, exhibited anti-pseudomonal effects. Overall, this work demonstrates the production of effective antimicrobial NPs, which may have clinical utility as mucus-penetrating tobramycin delivery vehicles, combining two widely used CF therapeutics into a single NP formulation. This nano-antibiotic represents a strategy to overcome the mucus barrier, increase local drug concentrations, avoid systemic adverse effects and improve outcomes for pulmonary infections in CF.

Three-dimensional modeling of the human fallopian tube fimbriae

OBJECTIVE: Ovarian cancer is the most lethal gynecological malignancy that affects women. Recent data suggests that the disease may originate in the fallopian fimbriae; however, the anatomical origin of ovarian carcinogenesis remains unclear. This is largely driven by our lack of knowledge regarding the structure and function of normal fimbriae and the relative paucity of models that accurately recapitulate the in vivo fallopian tube. Therefore, a human three-dimensional (3D) culture system was developed to examine the role of the fallopian fimbriae in serous tumorigenesis.

METHODS: Alginate matrix was utilized to support human fallopian fimbriae ex vivo. Fimbriae were cultured with factors hypothesized to contribute to carcinogenesis, namely; H2O2 (1mM) a mimetic of oxidative stress, insulin (5μg/ml) to stimulate glycolysis, and estradiol (E2, 10nM) which peaks before ovulation. Cultures were evaluated for changes in proliferation and p53 expression, criteria utilized to identify potential precursor lesions. Further, secretory factors were assessed after treatment with E2 to identify if steroid signaling induces a pro-tumorigenic microenvironment.

RESULTS: 3D fimbriae cultures maintained normal tissue architecture up to 7days, retaining both epithelial subtypes. Treatment of cultures with H2O2 or insulin significantly induced proliferation. However, p53 stabilization was unaffected by any particular treatment, although it was induced by ex vivo culturing. Moreover, E2-alone treatment significantly induced its canonical target PR and expression of IL8, a factor linked to poor outcome.

CONCLUSIONS: 3D alginate cultures of human fallopian fimbriae provide an important microphysiological model, which can be further utilized to investigate serous tumorigenesis originating from the fallopian tube.

Insulin and insulin-like growth factor signaling increases proliferation and hyperplasia of the ovarian surface epithelium and decreases follicular integrity through upregulation of the PI3-kinase pathway

BACKGROUND: The ovarian surface epithelium responds to cytokines and hormonal cues to initiate proliferation and migration following ovulation. Although insulin and IGF are potent proliferative factors for the ovarian surface epithelium and IGF is required for follicle development, increased insulin and IGF activity are correlated with at least two gynecologic conditions: polycystic ovary syndrome and epithelial ovarian cancer. Although insulin and IGF are often components of in vitro culture media, little is known about the effects that these growth factors may have on the ovarian surface epithelium morphology or how signaling in the ovarian surface may affect follicular health and development.

METHODS: Ovaries from CD1 mice were cultured in alginate hydrogels in the presence or absence of 5 μg/ml insulin or IGF-I, as well as small molecule inhibitors of IR/IGF1R, PI 3-kinase signaling, or MAPK signaling. Tissues were analyzed by immunohistochemistry for expression of cytokeratin 8 to mark the ovarian surface epithelium, Müllerian inhibiting substance to mark secondary follicles, and BrdU incorporation to assess proliferation. Changes in gene expression in the ovarian surface epithelium in response to insulin or IGF-I were analyzed by transcription array. Extracellular matrix organization was evaluated by expression and localization of collagen IV.

RESULTS: Culture of ovarian organoids with insulin or IGF-I resulted in formation of hyperplastic OSE approximately 4-6 cell layers thick with a high rate of proliferation, as well as decreased MIS expression in secondary follicles. Inhibition of the MAPK pathway restored MIS expression reduced by insulin but only partially restored normal OSE growth and morphology. Inhibition of the PI 3-kinase pathway restored MIS expression reduced by IGF-I and restored OSE growth to a single cell layer. Insulin and IGF-I altered organization of collagen IV, which was restored by inhibition of PI 3-kinase signaling.

CONCLUSIONS: While insulin and IGF are often required for propagation of primary cells, these cytokines may act as potent mitogens to disrupt cell growth, resulting in formation of hyperplastic OSE and decreased follicular integrity as measured by MIS expression and collagen deposition. This may be due partly to altered collagen IV deposition and organization in the ovary in response to insulin and IGF signaling mediated by PI 3-kinase.

Phenotypic characterization of an international Pseudomonas aeruginosa reference panel: strains of cystic fibrosis (CF) origin show less in vivo virulence than non-CF strains

Pseudomonas aeruginosa causes chronic lung infections in people with cystic fibrosis (CF) and acute opportunistic infections in people without CF. Forty two P. aeruginosa strains from a range of clinical and environmental sources were collated into a single reference strain panel to harmonise research on this diverse opportunistic pathogen. To facilitate further harmonized and comparable research on P. aeruginosa, we characterised the panel strains for growth rates, motility, virulence in the Galleria mellonella infection model, pyocyanin and alginate production, mucoid phenotype, lipopolysaccharide (LPS) pattern, biofilm formation, urease activity, antimicrobial and phage susceptibilities. Phenotypic diversity across the P. aeruginosa panel was apparent for all phenotypes examined agreeing with the marked variability seen in this species. However, except for growth rate, the phenotypic diversity among strains from CF versus non-CF sources was comparable. CF strains were less virulent in the G. mellonella model than non-CF strains (p=0.037). Transmissible CF strains generally lacked O antigen, produced less pyocyanin, and had low virulence in G. mellonella. Further, in the three sets of sequential CF strains, virulence, O-antigen expression and pyocyanin production were higher in the earlier isolate compared to the isolate obtained later in infection. Overall, full phenotypic characterization of the defined panel of P. aeruginosa strains increases our understanding of the virulence and pathogenesis of P. aeruginosa and may provide a valuable resource for the testing of novel therapies against this problematic pathogen.

Avaliação ecológica do efeito combinado de contaminantes ambientais

The assessment of ecological status of lotic freshwater bodies, based on stringent criteria of classification, has been defined by the Water Framework Directive (WFD), as a result of the implementation and optimization of methodologies that integrate physico-chemical, biological, and hydromorphological parameters. It is recognized that the application of this methodology is not easy, because it requires deep technical and scientific knowledge; it is time consuming in its application involving high financial costs. Thus, the main objective of this study was the development of cheaper and faster complementary methodologies that may contribute to the technical application of the classification criteria defined by the WFD, achieving the same final results of evaluation. In order to achieve this main goal, the river Mau, a small mountain river subjected to different stressors (eg, metals, pesticides), was established as the main sampling area. This thesis reviewed the historical development of various biotic indexes and its application in assessing water quality, especially highlighting the new paradigm defined by the WFD, and the corresponding actions developed for optimization and intercalibration of methodologies, evaluating the final state of water bodies. The ecological spatiotemporal characterization of the river Mau focused on the application of the WFD methodology, using at this stage only macroinvertebrates collected during four seasons. Results were compared with historical data of the last three years and they demonstrated that the river is in good condition. However, the ecological quality decreased at certain locations indicating that organisms were subjected to some type of disturbance. As the ecological quality can be conditioned by pulses of contamination from the sediments, in environmental adverse conditions, assays were performed with elutriates, obtained from sediments collected near the mining complex Braçal-Palhal. Results showed that this method was effective achieving the state of contamination, which may be important in prioritizing/scoring of critical areas within river ecosystems potentially impacted, using the WFD methodology. However, this methodology requires the collection of sediment which can promote the modification and / or loss of contaminants. To solve this potential problem, we developed a new methodology to obtain similar results. For this, we used a benthic microalga, belonging to the Portuguese flora, sensitive to organic pollution and metals. This methodology was optimized for application in situ, by immobilization of diatom in calcium alginate beads. The results showedthat their sensitivity and normal growth rate are similar to data obtained when used free cells of diatom. This new methodology allowed the achievement of a very quick response on the degree of contamination of a site, providing a complementary methodology to WFD.

Micro/nanoreservoirs for controlled release of active species in smart functional coatings

This work reports one possible way to develop new functional coatings used to increase the life time of metallic structures. The functionalities selected and attributed to model coatings in the frame of this work were corrosion protection, self-sensing and prevention of fouling (antifouling). The way used to confer those functionalities to coatings was based on the encapsulation of active compounds (corrosion inhibitors, pH indicators and biocides) in micro and nanocontainers followed by their incorporation into the coating matrices. To confer active corrosion protection, one corrosion inhibitor (2-mercaptobenzothiazole, MBT) was encapsulated in two different containers, firstly in silica nanocapsules (SiNC) and in polyurea microcapsules (PU-MC). The incorporation of both containers in different models coatings shows a significant improvement in the corrosion protection of aluminum alloy 2024 (AA2024). Following the same approach, SiNC and PU-MC were also used for the encapsulation of phenolphthalein (one well known pH indicator) to introduce sensing properties in polymeric coatings. SiNC and PU-MC containing phenolphthalein acted as corrosion sensor, showing a pink coloration due to the beginning of cathodic reaction, resulting in a pH increase identified by those capsules. Their sensing performance was proved in suspension and when integrated in coatings for aluminium alloy 2024 and magnesium alloy AZ31. In a similar way, the biocide activity (antifouling) was assigned to two polymeric matrices using SiNC for encapsulation of one biocide (Dichloro-2-octyl-2H-isothiazol-3-one, DCOIT) and also SiNC-MBT was tested as biocide. The antifouling activity of those two encapsulated compounds was assessed through inhibition and consequent decrease in the bioluminescence of modified E. coli. That effect was verified in suspension and when incorporated in coatings for AISI 1008 carbon steel. The developed micro and nanocontainers presented the desired performance, allowing the introduction of new functionalities to model coatings, showing potential to be used as functional additives in the next generation of multifunctional coatings.

Innovative edible films to improve storage ability of fresh-cut apple cv. Bravo de Esmolfe

Dissertação de mestrado, Hortofruticultura, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2015

Développement d’une matrice prébiotique pour l’encapsulation des probiotiques bactériocinogènes, destinée à l’alimentation animale - de la physicochimie à la biopharmacie

L’antibiorésistance est un problème de santé publique majeur, causé principalement par l’usage abusif d’antibiotiques dans les élevages. Les probiotiques sont une alternative potentielle aux antibiotiques. Cependant, acheminer ces microorganismes vivants et fonctionnels jusqu’au côlon est un grand défi, à cause du pH et des sels biliaires à affronter lors du passage gastro-intestinal. L’objectif de ce travail était de développer une matrice prébiotique capable de maintenir la survie et l’activité des probiotiques pendant le transit gastro-intestinal et de permettre leur libération dans le côlon. Pour atteindre cet objectif, cinq types de matrices sphériques (A, AI5, AI10, AI15, AI20) à base d’inuline (0 %, 5 %, 10 %, 15 % et 20 %) et d’alginate (2 %) ont été préparés par la méthode d’extrusion/gélification ionotropique. Trois souches probiotiques ont été utilisées au cours du développement des billes : Pediococcus acidilactici UL5 (UL5), Lactobacillus reuteri (LR) et Lactobacillus salivarius (LS). Dans un premier temps, toutes les formulations ont été caractérisées d’un point de vue physicochimique et microbiologique. Ces analyses ont permis de révéler une distribution homogène de l’inuline et de l’alginate au sein des matrices et ont démontré que la viabilité et la capacité antimicrobienne des souches utilisées n’étaient pas affectées par l’encapsulation. À la lumière de ces résultats, trois formulations A, AI5 et AI20 ont été sélectionnées pour la suite de l’étude. Dans un deuxième temps, la mucoadhésion et le comportement des billes A, AI5 et AI20 ont été étudiés dans les parties supérieures du tractus gastro-intestinal. Ces études ont démontré que la présence de l’inuline améliore les propriétés mucoadhésives des billes. Elles ont également établi que seule la formulation AI5 résiste jusqu’à la fin de la digestion. Ce comportement est expliqué en partie par l’interaction alginate-inuline décelée par spectroscopie infrarouge à transformée de Fourier (FTIR). Cette interaction était stable pour les billes AI5 au pH 6,8 mais instable pour la formulation AI20. Enfin, le comportement et la dynamique bactérienne de la formulation AI5 dans les milieux coliques fermenté et non fermenté ont été étudiés. Cette étude a révélé que les billes AI5 se dégradent et libèrent la totalité des bactéries après environ 4 heures d’incubation dans le milieu fermenté. Cette dégradation est due aux enzymes très abondantes dans ce milieu. En conclusion, la formulation AI5 s’est avérée être un très bon véhicule pour protéger les bactéries dans les parties supérieures du tube digestif et favoriser leur libération dans le côlon. Elle pourrait donc, être utilisée pour une application en alimentation animale.

Contribution of direct electron transfer mechanisms to overall electron transfer in microbial fuel cells utilising Shewanella oneidensis as biocatalyst

Objectives To investigate the contribution of direct electron transfer mechanisms to electricity production in microbial fuel cells by physically retaining Shewanella oneidensis cells close to or away from the anode electrode. Results A maximum power output of 114 ± 6 mWm−2 was obtained when cells were retained close to the anode using a dialysis membrane. This was 3.5 times more than when the cells were separated away from the anode. Without the membrane the maximum power output was 129 ± 6 mWm−2. The direct mechanisms of electron transfer contributed significantly to overall electron transfer from S. oneidensis to electrodes, a result that was corroborated by another experiment where S. oneidensis cells were entrapped in alginate gels. Conclusion S. oneidensis transfers electrons primarily by direct electron transfer as opposed to mediated electron transfer.

Materiais de mudança de fase em revestimentos

Dissertação para obtenção do grau de Mestre em Engenharia Civil na Área de especialização em Edificações