The effect of manganese on the grain size of commercial AZ31 alloy

The effect of manganese on gain refinement of a commercial AZ31 alloy has been investigated using an Al-60%Mn master alloy splatter as an alloying additive at 730 degrees C in aluminium titanite crucibles. It is shown that grain refinement by manganese is readily achievable in AZ31. Electron microprobe analyses reveal that prior to the addition of extra manganese the majority of the intermetallic particles found in AZ31 are of the AL(8)Mn(5) type. However, after the addition of extra manganese in the range from 0.1% to 0.8%, the predominant group of intermetallic particles changes to the metastable AlMn type. This leads to a hypothesis that the metastable AlMn intermetallic particles are more effective than Al8Mn5 as nucleation sites for magnesium grains. The hypothesis is supported by the observation that a long period of holding at 730 degrees C leads to an increase in grain size, due probably to the transformation of the metastable AlMn to the stable Al8Mn5. The hypothesis has also been used to understand the mechanism of grain refinement by superheating.

The effect of selected water-soluble excipients on the dissolution of paracetamol and ibuprofen

The purpose of this investigation was to study the dissolution behavior of paracetamol and ibuprofen in the presence of a range of selected potential excipients. First, a pH-solubility profile was generated for both drugs, and the effect of changing hydrodynamic conditions on the intrinsic dissolution rate was investigated. It was established that both drugs dissolved according to the diffusion-layer model. Paracetamol solubility (approximately 20.3 mg mL -1) did not vary from pH 1.2-8.0, corresponding to the in vivo range in the gastrointestinal tract. Ibuprofen had an intrinsic solubility of approximately 0.06 mg mL-1, and pKa was calculated as 4.4. Second, the effects of selected potential excipients (lactose, potassium bicarbonate, sodium bicarbonate, sodium chloride, and tartaric acid) were evaluated by measuring the effect of the inclusion of each additive in the dissolution medium on drug solubility, drug intrinsic dissolution rate, and solution viscosity. The results were evaluated using the diffusion-layer model, and it was determined that for paracetamol, the collected data fitted the model for all the excipients studied. For ibuprofen, it was found that there were differences between the excipients that raised the solution pH above the pK a to those that did not. For the excipients raising the pH above the pKa, the effect on intrinsic dissolution rate was not as high as that expected from the change in drug solubility. It was postulated that this might be due to lack of penetration of the excipient into the drug boundary layer microenvironment. Formulators may calculate the effect of adding an excipient based on solubility increases but may not find the dissolution rate improvement expected. Copyright © 2005 Taylor & Francis Inc.

Contrast discrimination and pattern masking: contrast gain control with fixed additive noise

We studied the visual mechanisms that serve to encode spatial contrast at threshold and supra-threshold levels. In a 2AFC contrast-discrimination task, observers had to detect the presence of a vertical 1 cycle deg-1 test grating (of contrast dc) that was superimposed on a similar vertical 1 cycle deg-1 pedestal grating, whereas in pattern masking the test grating was accompanied by a very different masking grating (horizontal 1 cycle deg-1, or oblique 3 cycles deg-1). When expressed as threshold contrast (dc at 75% correct) versus mask contrast (c) our results confirm previous ones in showing a characteristic 'dipper function' for contrast discrimination but a smoothly increasing threshold for pattern masking. However, fresh insight is gained by analysing and modelling performance (p; percent correct) as a joint function of (c, dc) - the performance surface. In contrast discrimination, psychometric functions (p versus logdc) are markedly less steep when c is above threshold, but in pattern masking this reduction of slope did not occur. We explored a standard gain-control model with six free parameters. Three parameters control the contrast response of the detection mechanism and one parameter weights the mask contrast in the cross-channel suppression effect. We assume that signal-detection performance (d') is limited by additive noise of constant variance. Noise level and lapse rate are also fitted parameters of the model. We show that this model accounts very accurately for the whole performance surface in both types of masking, and thus explains the threshold functions and the pattern of variation in psychometric slopes. The cross-channel weight is about 0.20. The model shows that the mechanism response to contrast increment (dc) is linearised by the presence of pedestal contrasts but remains nonlinear in pattern masking.

Effect of a tumour-produced lipid-mobilizing factor on protein synthesis and degradation

Treatment of murine myoblasts, myotubes and tumour cells with a tumour-produced lipid mobilizing factor (LMF), caused a concentration-dependent stimulation of protein synthesis, within a 24 h period. There was no effect on cell number or [3H] thymidine incorporation, but a similar concentration-dependent stimulation of 2-deoxyglucose uptake. LMF produced an increase in intracellular cyclic AMP levels, which was linearly (r2 = 0.973) related to the increase in protein synthesis. The effect of LMF was attenuated by the adenylate cyclase inhibitor MDL12330A, and was additive with the stimulation produced by forskolin. Both propranolol (10 μM) and the specific β3-adrenergic receptor antagonist SR 59230A (10-5M), significantly reduced the stimulation of protein synthesis induced by LMF. Protein synthesis was also increased by 69% (P = 0.006) in soleus muscles of mice administered LMF, while there was a 26% decrease in protein degradation (P = 0.03). While LMF had no effect on the lysosomal enzymes, cathepsins B and L, there was a decrease in proteasome activity, as determined both by the 'chymotrypsin-like' enzyme activity, as well as expression of proteasome α-type subunits, determined by Western blotting. These results show that in addition to its lipid-mobilizing activity LMF also increases protein accumulation in skeletal muscle both by an increase in protein synthesis and a decrease in protein catabolism. © 2001 Cancer Research Campaign.

The effect of complexes on combustion

The twin goals of low and efficient fuel use and minimum emissions are increasingly being addressed by research in both the motor and the catalyst industries of the world. This study was designed to attempt to investigate these goals. For diesel engine vehicles, this can be achieved by improving the efficiency of the fuel combustion in the combustion chamber. By having a suitable oxidation catalyst in the fuel one would expect the efficiency of the fuel combustion to be increased and fewer partial oxidation products to be formed. Also by placing a catalyst converter in the exhaust system partial oxidation products may be converted to more desirable final products. Finally, in this research the net catalytic effect of using an additive treated fuel and a blank ceramic monolith to trap the metal in the exhaust gases for potential use as catalytic converter was investigated. Suitable metal additives must yield a stable solution in the fuel tank. That is, they should not react with the air, water and rust that are always present. The research was targeted on the synthesis of hydrocarbon-soluble complexes that might exhibit unusually slow rates of ligand substitution. For materials containing metal ions, these properties are best met by using multi-dentate ligands that form neutral complexes. Metal complexes have been synthesised using acetylacetone derivatives, schiff base ligands and macrocyclic polyamine ligands, as potential pro-oxidant additives. Their thermal stabilities were also investigated using a differential thermal analysis instrument. The complexes were then investigated as potential additives for use in diesel fuel. The tests were conducted under controlled conditions using a diesel combustion bomb simulating the combustion process in the D.I. diesel engine, a test bed engine, and a vehicle engine.

Is socioeconomic position early in life associated with physical activity during adulthood following the accumulation of risk model with additive effects?

L'activité physique améliore la santé, mais seulement 4.8% des Canadiens atteignent le niveau recommandé. La position socio-économique est un des déterminants de l'activité physique les plus importants. Elle est associée à l’activité physique de manière transversale à l’adolescence et à l’âge adulte. Cette thèse a tenté de déterminer s'il y a une association à long terme entre la position socio-économique au début du parcours de vie et l’activité physique à l’âge adulte. S'il y en avait une, un deuxième objectif était de déterminer quel modèle théorique en épidémiologie des parcours de vie décrivait le mieux sa forme. Cette thèse comprend trois articles: une recension systématique et deux recherches originales. Dans la recension systématique, des recherches ont été faites dans Medline et EMBASE pour trouver les études ayant mesuré la position socio-économique avant l'âge de 18 ans et l'activité physique à ≥18 ans. Dans les deux recherches originales, la modélisation par équations structurelles a été utilisée pour comparer trois modèles alternatifs en épidémiologie des parcours de vie: le modèle d’accumulation de risque avec effets additifs, le modèle d’accumulation de risque avec effet déclenché et le modèle de période critique. Ces modèles ont été comparés dans deux cohortes prospectives représentatives à l'échelle nationale: la 1970 British birth cohort (n=16,571; première recherche) et l’Enquête longitudinale nationale sur les enfants et les jeunes (n=16,903; deuxième recherche). Dans la recension systématique, 10 619 articles ont été passés en revue par deux chercheurs indépendants et 42 ont été retenus. Pour le résultat «activité physique» (tous types et mesures confondus), une association significative avec la position socio-économique durant l’enfance fut trouvée dans 26/42 études (61,9%). Quand seulement l’activité physique durant les loisirs a été considérée, une association significative fut trouvée dans 21/31 études (67,7%). Dans un sous-échantillon de 21 études ayant une méthodologie plus forte, les proportions d’études ayant trouvé une association furent plus hautes : 15/21 (71,4%) pour tous les types et toutes les mesures d’activité physique et 12/15 (80%) pour l’activité physique de loisir seulement. Dans notre première recherche originale sur les données de la British birth cohort, pour la classe sociale, nous avons trouvé que le modèle d’accumulation de risque avec effets additifs s’est ajusté le mieux chez les hommes et les femmes pour l’activité physique de loisir, au travail et durant les transports. Dans notre deuxième recherche originale sur les données canadiennes sur l'activité physique de loisir, nous avons trouvé que chez les hommes, le modèle de période critique s’est ajusté le mieux aux données pour le niveau d’éducation et le revenu, alors que chez les femmes, le modèle d’accumulation de risque avec effets additifs s’est ajusté le mieux pour le revenu, tandis que le niveau d’éducation ne s’est ajusté à aucun des modèles testés. En conclusion, notre recension systématique indique que la position socio-économique au début du parcours de vie est associée à la pratique d'activité physique à l'âge adulte. Les résultats de nos deux recherches originales suggèrent un patron d’associations le mieux représenté par le modèle d’accumulation de risque avec effets additifs.

Transferability of Regional Permafrost Disturbance Susceptibility Modelling Using Generalized Linear and Generalized Additive Models

To effectively assess and mitigate risk of permafrost disturbance, disturbance-p rone areas can be predicted through the application of susceptibility models. In this study we developed regional susceptibility models for permafrost disturbances using a field disturbance inventory to test the transferability of the model to a broader region in the Canadian High Arctic. Resulting maps of susceptibility were then used to explore the effect of terrain variables on the occurrence of disturbances within this region. To account for a large range of landscape charac- teristics, the model was calibrated using two locations: Sabine Peninsula, Melville Island, NU, and Fosheim Pen- insula, Ellesmere Island, NU. Spatial patterns of disturbance were predicted with a generalized linear model (GLM) and generalized additive model (GAM), each calibrated using disturbed and randomized undisturbed lo- cations from both locations and GIS-derived terrain predictor variables including slope, potential incoming solar radiation, wetness index, topographic position index, elevation, and distance to water. Each model was validated for the Sabine and Fosheim Peninsulas using independent data sets while the transferability of the model to an independent site was assessed at Cape Bounty, Melville Island, NU. The regional GLM and GAM validated well for both calibration sites (Sabine and Fosheim) with the area under the receiver operating curves (AUROC) N 0.79. Both models were applied directly to Cape Bounty without calibration and validated equally with AUROC's of 0.76; however, each model predicted disturbed and undisturbed samples differently. Addition- ally, the sensitivity of the transferred model was assessed using data sets with different sample sizes. Results in- dicated that models based on larger sample sizes transferred more consistently and captured the variability within the terrain attributes in the respective study areas. Terrain attributes associated with the initiation of dis- turbances were similar regardless of the location. Disturbances commonly occurred on slopes between 4 and 15°, below Holocene marine limit, and in areas with low potential incoming solar radiation

Expanding the Design Space: Forging the Transition from 3D Printing to Additive Manufacturing

Thesis (Master's)--University of Washington, 2016-08

Development of combined acidification and separation of slurry: effect on slurry fractions composition and gaseous emission

Doutoramento em Engenharia do Ambiente - Instituto Superior de Agronomia - UL

Buy three but get only two: The smallest effect in a 2 × 2 ANOVA is always uninterpretable

Loftus (Memory & Cognition 6:312-319, 1978) distinguished between interpretable and uninterpretable interactions. Uninterpretable interactions are ambiguous, because they may be due to two additive main effects (no interaction) and a nonlinear relationship between the (latent) outcome variable and its indicator. Interpretable interactions can only be due to the presence of a true interactive effect in the outcome variable, regardless of the relationship that it establishes with its indicator. In the present article, we first show that same problem can arise when an unmeasured mediator has a nonlinear effect on the measured outcome variable. Then we integrate Loftus's arguments with a seemingly contradictory approach to interactions suggested by Rosnow and Rosenthal (Psychological Bulletin 105:143-146, 1989). We show that entire data patterns, not just interaction effects alone, produce interpretable or noninterpretable interactions. Next, we show that the same problem of interpretability can apply to main effects. Lastly, we give concrete advice on what researchers can do to generate data patterns that provide unambiguous evidence for hypothesized interactions.

Optimization of an innovative T6 heat treatment for the AlSi10Mg alloy processed by Laser-based Powder Bed Fusion: effect on microstructure, mechanical properties, and tribological behavior

Laser-based Powder Bed Fusion (L-PBF) technology is one of the most commonly used metal Additive Manufacturing (AM) techniques to produce highly customized and value-added parts. The AlSi10Mg alloy has received more attention in the L-PBF process due to its good printability, high strength/weight ratio, corrosion resistance, and relatively low cost. However, a deep understanding of the effect of heat treatments on this alloy's metastable microstructure is still required for developing tailored heat treatments for the L-PBF AlSi10Mg alloy to overcome the limits of the as-built condition. Several authors have already investigated the effects of conventional heat treatment on the microstructure and mechanical behavior of the L-PBF AlSi10Mg alloy but often overlooked the peculiarities of the starting supersatured and ultrafine microstructure induced by rapid solidification. For this reason, the effects of innovative T6 heat treatment (T6R) on the microstructure and mechanical behavior of the L-PBF AlSi10Mg alloy were assessed. The short solution soaking time (10 min) and the relatively low temperature (510 °C) reduced the typical porosity growth at high temperatures and led to a homogeneous distribution of fine globular Si particles in the Al matrix. In addition, it increased the amount of Mg and Si in the solid solution available for precipitation hardening during the aging step. The mechanical (at room temperature and 200 °C) and tribological properties of the T6R alloy were evaluated and compared with other solutions, especially with an optimized direct-aged alloy (T5 alloy). Results showed that the innovative T6R alloy exhibits the best mechanical trade-off between strength and ductility, the highest fatigue strength among the analyzed conditions, and interesting tribological behavior. Furthermore, the high-temperature mechanical performances of the heat-treated L-PBF AlSi10Mg alloy make it suitable for structural components operating in mild service conditions at 200 °C.

Cure Induced Residual Stresses on Thick Composite Components Manufactured by Additive Process

This study investigates the effect of an additive process in manufacturing of thick composites. Airstone 780 E epoxy resin and 785H Hardener system is used in the analysis since it is widely used wind turbine blade, namely thick components. As a fiber, fabric by SAERTEX (812 g/m2) with a 0-90 degrees layup direction is used. Temperature overshoot is a major issue during the manufacturing of thick composites. A high temperature overshoot leads to an increase in residual stresses. These residual stresses are causing warping, delamination, dimensional instability, and undesired distortion of composite structures. A coupled thermo-mechanical model capable of predicting cure induced residual stresses have been built using the commercial FE software Abaqus®. The possibility of building thick composite components by means of adding a finite number of sub-laminates has been investigated. The results have been compared against components manufactured following a standard route. The influence of pre-curing of the sub-laminates has also been addressed and results compared with standard practice. As a result of the study, it is found that introducing additive process can prevent temperature overshoot to occur and benefits the residual stresses generation during the curing process. However, the process time required increases by 50%, therefore increasing the manufacturing costs. An optimized cure cycle is required to minimize process time and cure induced defects simultaneously.

Obesity And Inflammation And The Effect On The Hematopoietic System.

Bone marrow is organized in specialized microenvironments known as 'marrow niches'. These are important for the maintenance of stem cells and their hematopoietic progenitors whose homeostasis also depends on other cell types present in the tissue. Extrinsic factors, such as infection and inflammatory states, may affect this system by causing cytokine dysregulation (imbalance in cytokine production) and changes in cell proliferation and self-renewal rates, and may also induce changes in the metabolism and cell cycle. Known to relate to chronic inflammation, obesity is responsible for systemic changes that are best studied in the cardiovascular system. Little is known regarding the changes in the hematopoietic system induced by the inflammatory state carried by obesity or the cell and molecular mechanisms involved. The understanding of the biological behavior of hematopoietic stem cells under obesity-induced chronic inflammation could help elucidate the pathophysiological mechanisms involved in other inflammatory processes, such as neoplastic diseases and bone marrow failure syndromes.

Effect Of Platform Connection And Abutment Material On Stress Distribution In Single Anterior Implant-supported Restorations: A Nonlinear 3-dimensional Finite Element Analysis.

Although various abutment connections and materials have recently been introduced, insufficient data exist regarding the effect of stress distribution on their mechanical performance. The purpose of this study was to investigate the effect of different abutment materials and platform connections on stress distribution in single anterior implant-supported restorations with the finite element method. Nine experimental groups were modeled from the combination of 3 platform connections (external hexagon, internal hexagon, and Morse tapered) and 3 abutment materials (titanium, zirconia, and hybrid) as follows: external hexagon-titanium, external hexagon-zirconia, external hexagon-hybrid, internal hexagon-titanium, internal hexagon-zirconia, internal hexagon-hybrid, Morse tapered-titanium, Morse tapered-zirconia, and Morse tapered-hybrid. Finite element models consisted of a 4×13-mm implant, anatomic abutment, and lithium disilicate central incisor crown cemented over the abutment. The 49 N occlusal loading was applied in 6 steps to simulate the incisal guidance. Equivalent von Mises stress (σvM) was used for both the qualitative and quantitative evaluation of the implant and abutment in all the groups and the maximum (σmax) and minimum (σmin) principal stresses for the numerical comparison of the zirconia parts. The highest abutment σvM occurred in the Morse-tapered groups and the lowest in the external hexagon-hybrid, internal hexagon-titanium, and internal hexagon-hybrid groups. The σmax and σmin values were lower in the hybrid groups than in the zirconia groups. The stress distribution concentrated in the abutment-implant interface in all the groups, regardless of the platform connection or abutment material. The platform connection influenced the stress on abutments more than the abutment material. The stress values for implants were similar among different platform connections, but greater stress concentrations were observed in internal connections.

The Effect Of Pelvic Floor Muscle Training Alone Or In Combination With Electrostimulation In The Treatment Of Sexual Dysfunction In Women With Multiple Sclerosis.

Sexual dysfunction (SD) affects up to 80% of multiple sclerosis (MS) patients and pelvic floor muscles (PFMs) play an important role in the sexual function of these patients. The objective of this paper is to evaluate the impact of a rehabilitation program to treat lower urinary tract symptoms on SD of women with MS. Thirty MS women were randomly allocated to one of three groups: pelvic floor muscle training (PFMT) with electromyographic (EMG) biofeedback and sham neuromuscular electrostimulation (NMES) (Group I), PFMT with EMG biofeedback and intravaginal NMES (Group II), and PFMT with EMG biofeedback and transcutaneous tibial nerve stimulation (TTNS) (Group III). Assessments, before and after the treatment, included: PFM function, PFM tone, flexibility of the vaginal opening and ability to relax the PFMs, and the Female Sexual Function Index (FSFI) questionnaire. After treatment, all groups showed improvements in all domains of the PERFECT scheme. PFM tone and flexibility of the vaginal opening was lower after the intervention only for Group II. All groups improved in arousal, lubrication, satisfaction and total score domains of the FSFI questionnaire. This study indicates that PFMT alone or in combination with intravaginal NMES or TTNS contributes to the improvement of SD.