The spectroscopic characterization of the sulphate mineral ettringite from Kuruman manganese deposits, South Africa

The mineral ettringite has been studied using a number of techniques, including XRD, SEM with EDX, thermogravimetry and vibrational spectroscopy. The mineral proved to be composed of 53% of ettringite and 47% of thaumasite in a solid solution. Thermogravimetry shows a mass loss of 46.2% up to 1000 °C. Raman spectroscopy identifies multiple sulphate symmetric stretching modes in line with the three sulphate crystallographically different sites. Raman spectroscopy also identifies a band at 1072 cm−1 attributed to a carbonate symmetric stretching mode, confirming the presence of thaumasite. The observation of multiple bands in the ν4 spectral region between 700 and 550 cm−1 offers evidence for the reduction in symmetry of the sulphate anion from Td to C2v or even lower symmetry. The Raman band at 3629 cm−1 is assigned to the OH unit stretching vibration and the broad feature at around 3487 cm−1 to water stretching bands. Vibrational spectroscopy enables an assessment of the molecular structure of natural ettringite to be made.

An analysis of Australia's legal regime for imposing liability on manufacturers of pharmaceutical drugs

Following a trial in June 2009 where the Federal Court heard submissions regarding whether Merck Sharpe and Dohme Australia should be held liable for an increased risk of cardiovascular conditions noted in patients who had taken the anti-inflammatory drug Vioxx, a judgment was handed down against MSDA in March 2010. MSDA appealed to the Full Federal Court, where they were successful. Special leave to appeal to the High Court of Australia was rejected in May 2012. This article will examine the themes raised in the trial judgment and the appropriateness of Australia’s statutory consumer protection regime through the lens of pharmaceutical drug injuries and side effects.

Changes of mortality and causes of death from 1970 to 2005 and decomposition analysis in Shandong province [山东省1970-2005年人群死亡率极死因变化与差别分解分析]

Objective To describe the trend of overall mortality and major causes of death in Shandong population from 1970 to 2005,and to quantitatively estimate the influential factors. Methods Trends of overall mortality and major causes of death were described using indicators such as mortality rates and age-adjusted death rates by comparing three large-scale mortality surveys in Shandong province. Difference decomposing method was applied to estimate the contribution of demographic and non-demographic factors for the change of mortality. Results The total mortality had had a slight change since 1970s,but had increased since 1990s.However,both the mortality rates of age-adjusted and age-specific decreased significantly. The mortality of Group Ⅰ diseases including infectious diseases as well maternal and perinatal diseases decreased drastically. By contrast, the mortality of non-communicable chronic diseases (NCDs)including cardiovascular diseases(CVDs),cancer and injuries increased. The sustentation of recent overall mortality was caused by the interaction of demographic and non-demographic factors which worked oppositely. Non-demographic factors were responsible for the decrease of Group Ⅰ disease and the increase of injuries. With respect to the increase of NCDs as a whole. Demographic factors might take the full responsibility and the non-demographic factors were the opposite force to reduce the mortality. Nevertheless, for the increase of some leading NCD diseases as CVDs and cancer, the increase was mainly due to non-demographic rather than demographic factors. Conclusion Through the interaction of the aggravation of ageing population and the enhancement of non-demographic effect, the overall mortality in Shandong would maintain a balance or slightly rise in the coming years. Group Ⅰ diseases in Shandong had been effectively under control. Strategies focusing on disease control and prevention should be transferred to chronic diseases, especially leading NCDs, such as CVDs and cancer.

Patron-driven acquisition of online video

Letting the patron choose ebooks has been a successful experience. Why not apply the same purchase model to other formats? This showcase outlines Queensland University of Technology’s experience with a trial of patron driven acquisition (PDA) for online video. The trial commencing in August 2012 provided access to over 700 online videos licensed from Kanopy across a number of discipline areas. As online video publishing is still in the early stages of development, and as the trial is only in the very early stages, it is too early to draw any firm conclusions about the likely suitability of this model for online video selection and acquisition. However, the trial provides some interesting initial comparisons with ebook PDA and existing online video purchase models and prompts further consideration of PDA as a method for online video selection and licensing.

Differential Regulation of Clusterin Isoforms by the Androgen Receptor

Clusterin (CLU) was initially reported as an androgen-repressed gene which is now shown to be an androgen-regulated ATP-independent cytoprotective molecular chaperone. CLU binds to a wide variety of client proteins to potently inhibit stress-induced protein aggregation and chaperone or stabilise conformations of proteins at times of cell stress. CLU is an enigmatic protein, being ascribed both pro- and anti-apoptotic roles. Recent evidence has shown that both secreted (sCLU) and nuclear (nCLU) isoforms can be produced, and that protein function is dependent on the sub-cellular localisation. We and others have shown that sCLU is cytoprotective, while nCLU is pro-apoptotic. It now seems likely that the apparently dichotomous functions of CLU result from the expression of different but related CLU isoforms and splice variants, and that cell survival depends in part on the relative expression of pro- versus anti-apoptotic CLU proteins. In cancer cells, increased sCLU expression is associated with increased resistance to apoptotic triggers and treatment resistance. CLU is a stress-induced protein upregulated after apoptotic triggers like androgen ablation and chemotherapy. Treatment strategies targeting stress-associated increases in sCLU expression enhance treatment-induced apoptosis and delay the emergence of androgen independence. Differential regulation of CLU isoforms and splice variants by androgens may be a pathway whereby cancer cells develop treatment resistance and evade apoptosis.

An evidence-based brochure to educate contact lens wearers about safe contact lens wear

Contact lenses are a successful and popular means to correct refractive error and are worn by just under 700,000 Australians1 and approximately 125 million people worldwide. The most serious complication of contact lens wear is microbial keratitis, a potentially sight-threatening corneal infection most often caused by bacteria. Gram-negative bacteria, in particular pseudomonas species, account for the majority of severe bacterial infections. Pathogens such as fungi or amoebae, which feature less often, are associated with significant morbidity. These unusual pathogens have come into the spotlight in recent times with an apparent association with specific lens cleaning solutions...

The association of early life supplemental nutrition with lean body mass and grip strength in adulthood : evidence from APCAPS

In the present study, we examined the associations of early nutrition with adult lean body mass (LBM) and muscle strength in a birth cohort that was established to assess the long-term impact of a nutrition program. Participants (n = 1,446, 32% female) were born near Hyderabad, India, in 29 villages from 1987 to 1990, during which time only intervention villages (n = 15) had a government program that offered balanced protein-calorie supplementation to pregnant women and children. Participants’ LBM and appendicular skeletal muscle mass were measured using dual energy x-ray absorptiometry; grip strength and information on lifestyle indicators, including diet and physical activity level, were also obtained. Ages (mean = 20.3 years) and body mass indexes (weight (kg)/height (m)2; mean = 19.5) of participants in 2 groups were similar. Current dietary energy intake was higher in the intervention group. Unadjusted LBM and grip strength were similar in 2 groups. After adjustment for potential confounders, the intervention group had lower LBM (β = −0.75; P = 0.03), appendicular skeletal muscle mass, and grip strength than did controls, but these differences were small in magnitude (<0.1 standard deviation). Multivariable regression analyses showed that current socioeconomic position, energy intake, and physical activity level had a positive association with adult LBM and muscle strength. This study could not detect a “programming” effect of early nutrition supplementation on adult LBM and muscle strength.

Modeling perceived influences on journalism : evidence from a cross-national survey of journalists

Surveying 1,700 journalists from seventeen countries, this study investigates perceived influences on news work. Analysis reveals a dimensional structure of six distinct domains—political, economic, organizational, professional, and procedural influences, as well as reference groups. Across countries, these six dimensions build up a hierarchical structure where organizational, professional, and procedural influences are perceived as more powerful limits to journalists' work than political and economic influences.

Validation of a parent-proxy quality of life questionnaire for paediatric chronic cough (PC-QOL)

Background Quality of life (QOL) measures are an important patient-relevant outcome measure for clinical studies. Currently there is no fully validated cough-specific QOL measure for paediatrics. The objective of this study was to validate a cough-specific QOL questionnaire for paediatric use. Method 43 children (28 males, 15 females; median age 29 months, IQR 20–41 months) newly referred for chronic cough participated. One parent of each child completed the 27-item Parent Cough-Specific QOL questionnaire (PC-QOL), and the generic child (Pediatric QOL Inventory 4.0 (PedsQL)) and parent QOL questionnaires (SF-12) and two cough-related measures (visual analogue score and verbal category descriptive score) on two occasions separated by 2–3 weeks. Cough counts were also objectively measured on both occasions. Results Internal consistency for both the domains and total PC-QOL at both test times was excellent (Cronbach alpha range 0.70–0.97). Evidence for repeatability and criterion validity was established, with significant correlations over time and significant relationships with the cough measures. The PC-QOL was sensitive to change across the test times and these changes were significantly related to changes in cough measures (PC-QOL with: verbal category descriptive score, rs=−0.37, p=0.016; visual analogue score, rs=−0.47, p=0.003). Significant correlations of the difference scores for the social domain of the PC-QOL and the domain and total scores of the PedsQL were also noted (rs=0.46, p=0.034). Conclusion The PC-QOL is a reliable and valid outcome measure that assesses QOL related to childhood cough at a given time point and measures changes in cough-specific QOL over time.

Surface dosimetry for very small X-ray beams

Introduction The dose to skin surface is an important factor for many radiotherapy treatment techniques. It is known that TPS predicted surface doses can be significantly different from actual ICRP skin doses as defined at 70 lm. A number of methods have been implemented for the accurate determination of surface dose including use of specific dosimeters such as TLDs and radiochromic film as well as Monte Carlo calculations. Stereotactic radiosurgery involves delivering very high doses per treatment fraction using small X-ray fields. To date, there has been limited data on surface doses for these very small field sizes. The purpose of this work is to evaluate surface doses by both measurements and Monte Carlo calculations for very small field sizes. Methods All measurements were performed on a Novalis Tx linear accelerator which has a 6 MV SRS X-ray beam mode which uses a specially thin flattening filter. Beam collimation was achieved by circular cones with apertures that gave field sizes ranging from 4 to 30 mm at the isocentre. The relative surface doses were measured using Gafchromic EBT3 film which has the active layer at a depth similar to the ICRP skin dose depth. Monte Carlo calculations were performed using the BEAMnrc/EGSnrc Monte Carlo codes (V4 r225). The specifications of the linear accelerator, including the collimator, were provided by the manufacturer. Optimisation of the incident X-ray beam was achieved by an iterative adjustment of the energy, spatial distribution and radial spread of the incident electron beam striking the target. The energy cutoff parameters were PCUT = 0.01 MeV and ECUT = 0.700 - MeV. Directional bremsstrahlung splitting was switched on for all BEAMnrc calculations. Relative surface doses were determined in a layer defined in a water phantom of the same thickness and depth as compared to the active later in the film. Results Measured surface doses using the EBT3 film varied between 13 and 16 % for the different cones with an uncertainty of 3 %. Monte Carlo calculated surface doses were in agreement to better than 2 % to the measured doses for all the treatment cones. Discussion and conclusions This work has shown the consistency of surface dose measurements using EBT3 film with Monte Carlo predicted values within the uncertainty of the measurements. As such, EBT3 film is recommended for in vivo surface dose measurements.

On display : Ravensthorpe Wildflower Show and the assembly of place

Each September since 1983 in the rural Shire of Ravensthorpe, Western Australia, volunteers collect samples of up to 700 wildfl ower species which are then displayed in the Ravensthorpe Senior Citizens Centre from 9.00 am to 4.00 pm daily over a two-week period. This chapter offers an ethnographic interpretation of this enduring annual event focusing on the 25th show held in 2007. The study contributes to understanding the complex and nuanced role of local wildflower shows in shaping and supporting rural senses of place and of community. Importantly, this particular type of festival, and more specifically this local instance, foregrounds a less-remarked aspect of festivals, namely the (re)production and celebration of place-specific knowledge through validations of, and interconnections between, scientific flower classification and emotive experience. This feature, encapsulated in Laurel Lamperd’s poem above, invites consideration of the ways in which local place knowledge and the simultaneous (re)production of ‘place’ are constituted by a complex layering of rational, objective ways of knowing and those which emphasize emotions, aesthetics and memories. This rural wildflower show not only mobilises both the rational and the emotional in ‘making sense of the world’ for local residents and for tourists, but also offers insights into the production of place as constituted in and through relations between humans and non-human life forms (Cloke & Jones, 2001; Conradson, 2005; see also Chapter 6).

Bike share's impact on car use : evidence from the United States, Great Britain, and Australia

There are currently more than 700 cities operating bike share programs. Purported benefits of bike share include flexible mobility, physical activity, reduced congestion, emissions and fuel use. Implicit or explicit in the calculation of program benefits are assumptions regarding the modes of travel replaced by bike share journeys. This paper examines the degree to which car trips are replaced by bike share, through an examination of survey and trip data from bike share programs in Melbourne, Brisbane, Washington, D.C., London, and Minneapolis/St. Paul. A secondary and unique component of this analysis examines motor vehicle support services required for bike share fleet rebalancing and maintenance. These two components are then combined to estimate bike share’s overall contribution to changes in vehicle kilometers traveled. The results indicate an estimated reduction in motor vehicle use due to bike share of approx. 90,000 km per annum in Melbourne and Minneapolis/St. Paul and 243,291 km for Washington, D.C. London’s bike share program however recorded an additional 766,341 km in motor vehicle use. This was largely due to a low car mode substitution rate and substantial truck use for rebalancing of bicycles. As bike share programs mature, evaluation of their effectiveness in reducing car use may become increasingly important. Researchers can adapt the analytical approach proposed in this paper to assist in the evaluation of current and future bike share programs.

Deterministic control of structural and optical properties of plasma-grown vertical graphene nanosheet networks via nitrogen gas variation

The effect of nitrogen on the growth of vertically oriented graphene nanosheets on catalyst-free silicon and glass substrates in a plasma-assisted process is studied. Different concentrations of nitrogen were found to act as versatile control knobs that could be used to tailor the length, number density and structural properties of the nanosheets. Nanosheets with different structural characteristics exhibit markedly different optical properties. The nanosheet samples were treated with a bovine serum albumin protein solution to investigate the effects of this variation on the optical properties for biosensing through confocal micro-Raman spectroscopy and UV-Vis spectrophotometry. © 2012 Optical Society of America.

Plasma-enabled, catalyst-free growth of carbon nanotubes on mechanically-written Si features with arbitrary shape

Simple, rapid, catalyst-free synthesis of complex patterns of long, vertically aligned multiwalled carbon nanotubes, strictly confined within mechanically-written features on a Si(1 0 0) surface is reported. It is shown that dense arrays of the nanotubes can nucleate and fully fill the features when the low-temperature microwave plasma is in a direct contact with the surface. This eliminates additional nanofabrication steps and inevitable contact losses in applications associated with carbon nanotube patterns. Using metal catalyst has long been considered essential for the nucleation and growth of surface-supported carbon nanotubes (CNTs) [1] and [2]. Only very recently, the possibility of CNT growth using non-metallic (e.g., oxide [3] and SiC [4]) catalysts or artificially created carbon-enriched surface layers [5] has been demonstrated. However, successful integration of carbon nanostructures into Si-based nanodevice platforms requires catalyst-free growth, as the catalyst nanoparticles introduce contact losses, and their catalytic activity is very difficult to control during the growth [6]. Furthermore, in many applications in microfluidics, biological and molecular filters, electronic, sensor, and energy conversion nanodevices, the CNTs need to be arranged in specific complex patterns [7] and [8]. These patterns need to contain the basic features (e.g., lines and dots) written using simple procedures and fully filled with dense arrays of high-quality, straight, yet separated nanotubes. In this paper, we report on a completely metal or oxide catalyst-free plasma-based approach for the direct and rapid growth of dense arrays of long vertically-aligned multi-walled carbon nanotubes arranged into complex patterns made of various combinations of basic features on a Si(1 0 0) surface written using simple mechanical techniques. The process was conducted in a plasma environment [9] and [10] produced by a microwave discharge which typically generates the low-temperature plasmas at the discharge power below 1 kW [11]. Our process starts from mechanical writing (scribing) a pattern of arbitrary features on pre-treated Si(1 0 0) wafers. Before and after the mechanical feature writing, the Si(1 0 0) substrates were cleaned in an aqueous solution of hydrofluoric acid for 2 min to remove any possible contaminations (such as oil traces which could decompose to free carbon at elevated temperatures) from the substrate surface. A piece of another silicon wafer cleaned in the same way as the substrate, or a diamond scriber were used to produce the growth patterns by a simple arbitrary mechanical writing, i.e., by making linear scratches or dot punctures on the Si wafer surface. The results were the same in both cases, i.e., when scratching the surface by Si or a diamond scriber. The procedure for preparation of the substrates did not involve any possibility of external metallic contaminations on the substrate surface. After the preparation, the substrates were loaded into an ASTeX model 5200 chemical vapour deposition (CVD) reactor, which was very carefully conditioned to remove any residue contamination. The samples were heated to at least 800 °C to remove any oxide that could have formed during the sample loading [12]. After loading the substrates into the reactor chamber, N2 gas was supplied into the chamber at the pressure of 7 Torr to ignite and sustain the discharge at the total power of 200 W. Then, a mixture of CH4 and 60% of N2 gases were supplied at 20 Torr, and the discharge power was increased to 700 W (power density of approximately 1.49 W/cm3). During the process, the microwave plasma was in a direct contact with the substrate. During the plasma exposure, no external heating source was used, and the substrate temperature (∼850 °C) was maintained merely due to the plasma heating. The features were exposed to a microwave plasma for 3–5 min. A photograph of the reactor and the plasma discharge is shown in Fig. 1a and b.

Effect of gas pressure on electron field emission from carbon nanotube forests

This article quantifies the effect of the operating pressure of the H 2 + C 2H 4 gas mixture on the current density and threshold voltage of the electron emission from dense forests of multiwalled carbon nanotubes synthesized using thermal catalytic Chemical Vapor Deposition under near atmospheric pressure process conditions. The results suggest that in the pressure range of interest 400-700 Torr the field emission properties can be substantially improved by operating the process at lower gas pressures when the nanostructure aspect ratios are higher. The obtained threshold voltage ∼1.75 V/μm and the emission current densities ∼10 mA/cm 2 offer competitive advantages compared with the results reported by other authors. Copyright