Isolation and structural determination of non-racemic tertiary cathinone derivatives

The racemic tertiary cathinones N,N-dimethylcathinone (1), N,N-diethylcathinone (2) and 2-(1-pyrrolidinyl)-propiophenone (3) have been prepared in reasonable yield and characterized using NMR and mass spectroscopy. HPLC indicates that these compounds are isolated as the anticipated racemic mixture. These can then be co-crystallized with (+)-O,O′-di-p-toluoyl-d-tartaric, (+)-O,O′-dibenzoyl-d-tartaric and (-)-O,O′-dibenzoyl-l-tartaric acids giving the single enantiomers S and R respectively of 1, 2 and 3, in the presence of sodium hydroxide through a dynamic kinetic resolution. X-ray structural determination confirmed the enantioselectivity. The free amines could be obtained following basification and extraction. In methanol these are reasonably stable for the period of several hours, and their identity was confirmed by HPLC and CD spectroscopy.

Resistance of alkali activated slag concretes to chloride environments based on chloride penetration measurements

ABSTRACT

One of the binder systems with low environmental footprint is alkali activated slag concretes (AASC), made by adding alkalis such as sodium hydroxide and sodium silicate to industrial by-products such as ground granulated blast furnace slag (GGBS). Whilst they have the similar behaviour as that of traditional cement systems in terms of strength and structural behaviour, AASC do exhibit superior performance in terms of abrasion and acid resistance and fire protection.
In this article, the authors focus their attention on chloride ingress into different grades of AASC. The mix variables in AASC included water-to-binder, binder to aggregate ratio, percentage of alkali and the SiO2/Na2O ratio (silica modulus, Ms). The first challenge is to get mixes for different range of workability (with slump values from 40mm to 240mm) and reasonable early age and long term compressive strength according to each one. Then the chloride diffusion and migration in those mixes were measured and compared with same normal concretes in the existed literature based on chloride penetration depth. Comparing the chloride ingress between tradition concretes and AASCs is worthwhile to prove the possibility of increasing concrete lifetime in proximity to sea and deciding while such concretes are practical for use. Findings show that compared to the PC concretes, the AAS concretes have lower rate of chloride ingress.

Resistance of alkali activated slag concretes to chloride environments

ABSTRACT: Researchers are focusing their attention on alternative binder systems using 100% supplementary cementitious materials as it allows better control over the microstructure formation and low to moderate environmental footprint. One such system being considered is alkali activated slag concretes (AASC), made by adding alkalis such as sodium hydroxide and sodium silicate to ground granulated blast furnace slag (GGBS). Whilst they have a similar behaviour as that of traditional cement systems in terms of strength and structural behaviour, AASC are reported to exhibit superior performance in terms of abrasion,acid resistance and fire protection.
In this article, the authors investigate chloride ingress into different grades of AASC. The mix variables in AASC included water to binder, and binder to aggregate ratio, percentage of alkali and the SiO2/Na2O ratio (silica modulus, Ms). The first challenge was to develop mixes for different range of workability (with slump values from 40mm to 240mm) and reasonable early age and long term compressive strength. Further chloride ingress into those mixes were assessed and compared with the data from normal concretes based on literature. Findings show that compared to the PC concretes, the AAS concretes have lower rate of chloride ingress.

Mixing performance evaluation of additive manufactured milli-scale reactors

The mixing performance of three passive milli-scale reactors with different geometries was investigated at different Reynolds numbers. The effects of design and operating characteristics such as mixing channel shape and volume flow rate were investigated. The main objective of this work was to demonstrate a process design method that uses on Computational Fluid Dynamics (CFD) for modeling and Additive Manufacturing (AM) technology for manufacture. The reactors were designed and simulated using SolidWorks and Fluent 15.0 software, respectively. Manufacturing of the devices was performed with an EOS M-series AM system. Step response experiments with distilled Millipore water and sodium hydroxide solution provided time-dependent concentration profiles. Villermaux-Dushman reaction experiments were also conducted for additional verification of CFD results and for mixing efficiency evaluation of the different geometries. Time-dependent concentration data and reaction evaluation showed that the performance of the AM-manufactured reactors matched the CFD results reasonably well. The proposed design method allows the implementation of new and innovative solutions, especially in the process design phase, for industrial scale reactor technologies. In addition, rapid implementation is another advantage due to the virtual flow design and due to the fast manufacturing which uses the same geometric file formats.

Melhoria do processo de lavação das rolhas de cortiça

O presente trabalho, realizado na empresa Amorim & Irmãos, S.A. teve como principal objetivo a avaliação e otimização da lavação de rolhas de cortiça técnicas, designadas por Twin Top®, em termos do perfil de consumo de reagentes químicos e do desenvolvimento da sua brancura. Para tal foi desenvolvida uma metodologia de análise de brancura de rolhas Twin Top® que serviu de base para a determinação de uma gama de brancuras aceitável. Para além disto, efetuou-se a avaliação do processo de lavação atualmente praticado e apartir do qual se realizaram os ensaios de otimização a nível laboratorial e piloto. Foram aplicados diferentes métodos de análise tais como, UV-Vis, FTIR-ATR, RMN e brancura ISO. Tendo como base de análise os espetros de refletância difusa de espetroscopia de UV-Vis foi proposta uma metodologia de determinação da brancura de rolhas Twin Top® a 457nm, adoptando as condições da Norma ISO 3688, aplicada na indústria da pasta e papel. De seguida, aplicando o método anteriormente definido, analisaram-se 1000 rolhas Twin Top® de lavação branca. Sendo que os resultados demonstraram que para rolhas dentro de especificação a brancura ISO deve estar entre os 30 e 35%. Foram ainda analisadas rolhas de diferentes classes visuais e provenientes de várias máquinas de lavação da fábrica para determinar possíveis diferenças. Para proceder à avaliação da lavação existente analisaram-se as colas usadas na produção das rolhas, um grânulo de cortiça e a matéria seca do efluente de lavação por FTIR-ATR e RMN. Desta avaliação resultou a presença de compostos de cortiça e cola degradada no efluente de lavação. Determinou-se a concentração dos reagentes intervenientes no processo que se mostraram de acordo com as especificações indicadas pelos fornecedores. Para a otimização da lavação combinou-se o peróxido de hidrogénio e hidróxido de sódio em diferentes quantidades, concentrações e diferentes tempos de reação o que permitiu identificar a melhor alternativa à lavação convencional. Assim existem duas propostas que devem ser tidas em consideração: uma em que a lavação mantém a mesma sequência da convencional e em que se altera o local de adição dos reagentes, que deve ser o mais próxima e direta possível das rolhas, e a outra em que se reduz o tempo do processo em 29,3 min, que compreende apenas uma oxidação e em que a quantidade de reagentes aplicada corresponde à soma dos volumes de reagentes das três oxidações do processo convencional.

Avaliação da atividade antimicrobiana de filmes protéicos a base de anchoita (engraulis anchoita) incorporados com ácidos orgânicos.

Os filmes são produzidos a partir de macromoléculas, que podem ser utilizados como embalagem, como os polissacarídeos, lipídeos e proteínas. As proteínas se destacam dos demais, pois possuem uma estrutura com 20 monômeros diferentes, que confere um amplo potencial de ligações intermoleculares. A incorporação de agentes ativos em filmes é uma alternativa como embalagem, para inibir ou retardar a multiplicação de microrganismos patógenos e deteriorantes em alimentos. O objetivo deste trabalho foi avaliar a atividade antimicrobiana de filmes à base de isolado protéico de anchoita (Engraulis anchoita) – IPA adicionados de ácidos orgânicos. Para tanto, foi elaborado o IPA, pela solubilização alcalina da proteína e precipitação no ponto isoelétrico a partir de carne mecanicamente separada. O IPA foi avaliado quanto a sua composição proximal, aminoacídica e por DSC. A solução formadora dos filmes foi elaborada a partir de IPA, água, glicerol e hidróxido de sódio. As formulações dos filmes foram elaboradas segundo um planejamento fatorial 23 . Foram avaliadas as propriedades físico-químicas de resistência a tração (RT) e elongação (E); espessura, solubilidade e permeabilidade ao vapor de água (PVA); a diferença de cor (∆E*) e opacidade (Y) e microscopia eletrônica de varredura (MEV) de filmes à base de IPA. Os filmes com diferentes concentrações de ácido sórbico (AS) ou ácido benzóico (AB) foram desenvolvidos a partir da condição cujo as propriedades físico-químicas foram as melhores, sendo comparados aos filmes controles. Estes, foram avaliados quanto a sua atividade antimicrobiana frente aos microrganismos Escherichia coli O157:H7, Listeria monocytogenes, Staphylococcus aureus e Salmonella Enteritidis pelo método de difusão em disco, além das propriedades físico-químicas, MEV e FT-IV. Os filmes com maior atividade antimicrobiana e os filmes controle foram aplicados sobre carne bovina, inoculados com os microrganismos inibidos no método de difusão em disco e armazenados a 5°C. Estes, foram avaliados a cada 2 dias durante 12 dias de armazenamento, pela método de contagem em gotas. O IPA apresentou 88,8% de proteína e 53,3% de aminoácidos polares e temperatura de desnaturação de 62,2°C. A espessura, PVA, ∆E* e Y dos filmes não foram afetados pelas variáveis estudadas no experimento. A menor solubilidade e maior RT dos filmes ocorreram em baixa concentração de IPA, glicerol e tratamento térmico, mas a E aumentou com o acréscimo dessas variáveis. As MEV das superfícies dos filmes foram homogêneas, para aqueles com leve tratamento térmico. O aumento da concentração de AS e AB na faixa de 0,50 a 1,50% resultou na diminuição da RT e aumento da E, solubilidade, ∆E* e Y. Houve mudança da organização molecular e interações intermoleculares entre as moléculas de IPA e AB testados pela avaliação do FT-IV. As MEV revelaram microporos em filmes com 1,50% de AS, o que resultou em filmes com menor homogeneidade. A maior atividade antimicrobiana foi verificada nos filmes com 1,50% de AS e AB frente a E. coli O157:H7, L. monocytogenes e S. Enteritidis. Estes filmes foram aplicados sobre carne bovina inoculada com E. coli O157:H7 e L. monocytogenes. Os filmes de AS frente a E. coli O157:H7 e L. monocytogenes apresentaram uma redução de 5 e 4 log UFC.g-1, respectivamente, em relação ao filme controle. O efeito do AB frente a estas bactérias, apresentou uma redução de 6 e 5 log UFC.g-1, ao final do 12° dia de armazenamento, respectivamente. Os filmes elaborados à base de IPA, adicionados de AS ou AB podem ser eficazes contra os patógenos alimentares testados.

Produção de biodiesel de blendas dos óleos de mamona e arroz em escala piloto

A utilização do óleo de mamona como matéria-prima para produção de biodiesel mostra-se inviável na combustão interna do motor devido sua natureza química incomum que lhe confere especificações acima do permitido nas especificações técnicas da legislação nacional brasileira. Desta forma, a blenda com óleo de arroz refinado (OM:OA) qualifica o biodiesel atendendo a legislação nacional, além de corrigir a elevada acidez do óleo bruto de mamona prejudicial ao processo de transesterificação homogênea básica. No presente estudo realizou-se a produção de biodiesel etílico em escala piloto a partir de blendas de óleo bruto de mamona e óleo refinado de arroz em dois processos: o primeiro processo adotando a mistura direta dos dois óleos e o segundo processo pela esterificação antecipada do óleo bruto de mamona. Ambos os processos foram aplicados visando tanto definir os critérios de processo (acidez inicial) quanto o cumprimento das especificações técnicas (viscosidade e densidade). A produção em escala piloto (200 litros/batelada) foi realizada na Usina Demonstrativa para Produção de Biodiesel – BIOSUL (Edital FINEP, 2005) da Universidade Federal do Rio Grande - FURG utilizando em ambos os processos transesterificação, com hidróxido de sódio, e esterificação com ácido sulfúrico. Os processos apresentaram resultados satisfatórios, sendo o processo de mistura direta (Processo A) o que obteve melhores rendimentos (94,04%, blenda 20:80) enquanto que o processo de pré- esterificação (Processo B) foi aquele que proporcionou a maior fração de óleo de mamona na blenda (80,36%, 33:67). Os resultados para o Processo A de glicerol livre, monoacilgliceróis, diacilgliceróis, triacilgliceróis e de glicerol total foram, respectivamente, de 1,322 %, 6,092 %, 1,000 %, 0,884 e 3,152%. Neste estudo foi comprovada a viabilidade do processamento, em batelada, de blendas dos óleos de mamona e arroz. O óleo de mamona bruto pode ser utilizado em até 30% produzindo biodiesel dentro da legislação, verificando-se assim a viabilidade do uso da mamona na produção de biocombustíveis.

Nanoestruturas multicomponentes de CoFe2O4/Ag visando aplicações biológicas

Dissertação (mestrado)—Universidade de Brasília, Instituto de Física, Programa de Pós-Graduação em Física, 2015.

Síntese regioespecífica de novas N-acil trialometil pirazolinas graxas

Nesse trabalho é descrita a síntese de três hidrazidas graxas monosubstituídas [R1C(O)NHNH2, onde R1 =C15H31, C17H35, C17H33] derivadas dos ácidos graxos palmítico, esteárico e oléico, respectivamente, utilizando duas novas metodologias, primeiramente a partir de monocloridrato de hidrazina em presença de hidróxido de sódio e, em um segundo momento, usando dicloridrato de hidrazina e metóxido de sódio. Ambas as metodologias foram realizadas em metanol como solvente, sendo investigadas as proporções estequiométricas específicas para cada método utilizado. A síntese das hidrazidas graxas com as 4-alcóxi-1,1,1-trialometil-3-alquen-2-onas substituídas [R3C(O)C= C(R2 )(OR), onde R3 = CF3, CCl3; R2 = Me, 4-Me-C6H4, 4- OMe-C6H4, 4-Br-C6H4, 4-Cl-C6H4, 4-F-C6H4], através da reação de ciclocondensação do tipo [3+2] catalisada por BF3.MeOH, favoreceu a síntese regioespecífica de duas novas séries de N-acil trialometil pirazolinas graxas, com rendimentos de bons a excelentes (80 a 90%) e alto grau de pureza, tendo suas estruturas caracterizadas através de dados de Espectroscopia de Infravermelho, Cromatografia Gasosa Acoplada a Espectrometria de Massas e Ressonância Magnética Nuclear de 1H e 13C.

Additional steps in mechanical recyling of PET

This study presents the laboratory scale results of an extra step in Poly (ethylene terephthalate) - PET mechanical recycling (grinding, washing, drying and reprocessing): a chemical washing after the conventional one. Cooking oil PET bottle flakes were washed in water and then subjected to a reaction with an aqueous solution of sodium hydroxide 5 M at 90 degrees C for 10 min (chemical washing). After rinsing and drying, the flakes were characterized by thermogravimetry, gas chromatography and elemental analysis tests. The results indicated that the chemically washed material had higher purity than PET washed only with water: 99.3% and 96.7%, respectively, which undoubtedly implies properties, applications and prices closer to those of virgin resin. The production of purified terephthalic acid (TPA) from the chemical washing residue was optimized and reached a purity of 99.6%. Despite the results, the use of chemically washed PET and of TPA obtained is not recommended for direct contact with food, since they still contain some impurities. (C) 2009 Elsevier Ltd. All rights reserved.

Characterization of Post-Consumer PET after Removal of the Original Surface: Influence of Raw Material

Post-consumer cooking oil and soft drink PET bottles (PEToil and PETsoft drink) were ground and washed only with water (conventional washing). The polymer was then chemically washed (10min in an aqueous solution of sodium hydroxide 5mol center dot L-1 at 90 degrees C) and rinsed. The materials before and after chemical washing were characterized by intrinsic viscosity, differential scanning calorimetry, thermogravimetry, elemental analysis, scanning electron microscopy with X-ray spectrum microanalysis, and gas chromatography coupled to mass spectrometry. The results indicated that conventionally washed PEToil is the material that most differs among the four tested ones, and that the other three are more similar to each other and to what is expected for pure PET. For example, the composition of PEToil washed only in water contained 30 volatile organic compounds, 5 nonvolatile compounds, and 7 metals, while PETsoft drink washed conventionally and chemically contained 5 volatile organic compounds and no metal or nonvolatile organic compounds.

Obtenção de polímeros de LCC para aplicação como antioxidante de biodiesel de soja

Biodiesel is a fuel obtained from vegetable oils, such as soy, castorbean, among others. The monoester of fatty acid of these oils have chains with mono, di and tri double connections. The presence of these insaturations are susceptible to oxidization. Antioxidants are substances able to prevent oxidization from oils, fats, fat foods, as well as esters of Alquila( biodiesel). The objective of this work is to summarize a new antioxidant from the Cashew Nut Shell Liquid (CNSL) using the electrolysis technique. A current of 2 amperes was used in a single cell of only one group and two eletrodos of stainless steel 304 in a solution of methanol, together with the eletrolits: acetic acid, sodium chloride and sodium hydroxide, for two hours of agitation. The electrolysis products are characterized by the techniques of cromatography in a thin layer, spectroscopy of infrared and gravimetric analysis. The material was submitted to tests of oxidative stability made by the techniques of spectropy of impendancy and Rancimat (EN 14112). The analyses of characterization suggest that the polimerization of the electrolytic material ocurred. The application results of these materials as antioxidants of soy biodiesel showed that the order of the oxidative stability was obtained by both techniques used

Estudo da síntese e propriedade magnética de ferritas de manganês/cobalto dopadas com níquel

For the chemical method of synthesis of co-precipitation were produced ferrite powders manganese-cobalt equal stoichiometric formula Mn (1-x) Co (x) Fe2O4, for 0 < x < 1, first reagent element using as the hydroxide ammonium and second time using sodium hydroxide. The obtained powders were calcined at 400 ° C, 650 ° C, 900 ° C and 1150 ° C in a conventional oven type furnace with an air atmosphere for a period of 240 minutes. Other samples were calcined at a temperature of 900 ° C in a controlled atmosphere of argon, to evaluate the possible influence of the atmosphere on the final results the structure and morphology. The samples were also calcined in a microwave oven at 400 ° C and 650 ° C for a period of 45 minutes possible to evaluate the performance of this type of heat treatment furnace. It was successfully tested the ability of this group include isomorphic ferrite with the inclusion of nickel cations in order to evaluate the occurrence of disorder in the crystalline structures and their changes in magnetic characteristics.To identify the structural, morphological, chemical composition and proportions, as well as their magnetic characteristics were performed characterization tests of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDX), thermogravimetric (TG), vibrating sample magnetometry (MAV) and Mössbauer spectroscopy. These tests revealed the occurrence of distortion in the crystal lattice, changes in magnetic response, occurrence of nanosized particles and superparamagnetism

Adsorção de cobre e cromo utilizando fibra de sisal visando o tratamento da água produzida pela indústria petrolífera

Currently, the oil industry is the biggest cause of environmental pollution. The objective was to reduce the concentration of copper and chromium in the water produced by the oil industry. It was used as adsorbent natural sisal fiber Agave sp treated with nitric acid and sodium hydroxide. All vegetable fibers have physical and morphological properties that enablies the adsorption of pollutants. The basic composition of sisal is cellulose, hemicellulose and lignin. The features are typically found in the characterization of vegetable fibers, except the surface area that was practically zero. In the first stage of adsorption, it was evaluated the effect of temperature and time skeeking to optimize the execution of the factorial design. The results showed that the most feasible fiber was the one treated with acid in five hours (30°C). The second phase was a factorial design, using acid and five hours, this time was it determined in the first phase. The tests were conducted following the experimental design and the results were analyzed by statistical methods in order to optimize the main parameters that influence the process: pH, concentration (mol / L) and fiber mass/ metal solution volume. The volume / mass ratio factor showed significant interference in the adsorption process of chromium and copper. The results obtained after optimization showed that the highest percentages of extraction (98%) were obtained on the following operating conditions: pH: 5-6, Concentration: 100 ppm and mass/ volume: 1 gram of fiber/50mL solution. The results showed that the adsorption process was efficient to remove chromium and copper using sisal fibers, however, requiring further studies to optimize the process.

An Investigation of Waste Glass-Based Geopolymers Supplemented with Alumina

An increased consideration of sustainability throughout society has resulted in a surge of research investigating sustainable alternatives to existing construction materials. A new binder system, called a geopolymer, is being investigated to supplement ordinary portland cement (OPC) concrete, which has come under scrutiny because of the CO2 emissions inherent in its production. Geopolymers are produced from the alkali activation of a powdered aluminosilicate source by an alkaline solution, which results in a dense three-dimensional matrix of tetrahedrally linked aluminosilicates. Geopolymers have shown great potential as a building construction material, offering similar mechanical and durability properties to OPC. Additionally, geopolymers have the added value of a considerably smaller carbon footprint than OPC. This research considered the compressive strength, microstructure and composition of geopolymers made from two types of waste glass with varying aluminum contents. Waste glass shows great potential for mainstream use in geopolymers due to its chemical and physical homogeneity as well as its high content of amorphous silica, which could eliminate the need for sodium silicate. However, the lack of aluminum is thought to negatively affect the mechanical performance and alkali stability of the geopolymer system. Mortars were designed using various combinations of glass and metakaolin or fly ash to supplement the aluminum in the system. Mortar made from the high-Al glass (12% Al2O3) reached over 10,000 psi at six months. Mortar made from the low-Al glass (<1% Al2O3) did not perform as well and remained sticky even after several weeks of curing, most likely due to the lack of Al which is believed to cause hardening in geopolymers. A moderate metakaolin replacement (25-38% by mass) was found to positively affect the compressive strength of mortars made with either type of glass. Though the microstructure of the mortar was quite indicative of mechanical performance, composition was also found to be important. The initial stoichiometry of the bulk mixture was maintained fairly closely, especially in mixtures made with fine glass. This research has shown that glass has great potential for use in geopolymers, when care is given to consider the compositional and physical properties of the glass in mixture design.