THE INFLUENCE OF GAMMA-RADIATION ON POLYAMIDE-1010 AGGREGATE STRUCTURES

The influence of gamma-radiation on polyamide 1010 aggregate structures and crystal damage were examined by using wide angle X-ray diffraction (WAXD) and small angle X-ray scattering (SAXS) techniques. The results revealed that some structural parameters of the aggregated state, the density differences and the degree of crystallinity W-c,W-x, essentially decreased with increasing radiation dose, but the specific surface O-s increased. Crosslinking and scission of irradiated polyamide 1010 samples occurred mainly in amorphous and interphase regions, and crystal damage and amorphization induced by gamma-radiation spread from the interphase and extended into the crystal phase with increasing radiation dose. This result also indicated that the (010) reflection with the hydrogen bond was more susceptible to the action of radiation.

EFFECT OF IRRADIATION ON CRYSTALLINITY AND MECHANICAL-PROPERTIES OF ULTRAHIGH MOLECULAR-WEIGHT POLYETHYLENE

Ultrahigh molecular weight polyethylene (UHMWPE) has been irradiated (0-40 Mrad) with a Co-60 source at room temperature under vacuum. The crystallinity has been investigated by differential scanning calorimetry (DSC) and small-angle X-ray scattering (SAXS). The mechanical properties have been determined at room temperature. A significant increase of heat of fusion can be seen at low irradiation doses, which is attributed to crystallization, caused by chain scission during the process of irradiation. It is also observed that the thickness of the lamellae changes with irradiation dose. The Young's modulus has been improved significantly after irradiation at low doses. (C) 1993 John Wiley & Sons, Inc.

STUDY ON STRUCTURE-PROPERTY RELATIONSHIP OF POLYIMIDE BLENDS .2. STRUCTURE AND MISCIBILITY OF POLYIMIDE PBPI-E/PTI-E BLENDS

The structure and miscibility of polyimide PBPI-E/PTI-E blends were studied by wide- and small-angle X-ray scattering and dynamic mechanical analysis, where PBPI-E is a biphenyl-dianhydride-based polyimide, and PTI-E is a polyimide from 4,4'-thiodiphthalic anhydride and 4,4'-oxydianiline. The results obtained show that there exists a paracrystalline structure in the blends with high content of PBPI-E, but this does not affect the miscibility of the blends. The blends are miscible over the entire composition range, since only one T(g) was observed for each blend. Meanwhile, the segregation of PTI-E during crystallization of PBPI-E in the blends is interlamellar.

STRUCTURE OF MESOMORPHIC FORM OF ISOTACTIC POLYPROPYLENE

The structure of quenched isotactic polypropylene (iPP) films, including samples etched with fuming nitric acid (FNA), has been studied by infrared (IR) spectra, wide-angle x-ray diffraction (WAXD), small-angle x-ray scattering (SAXS), and differential scanning calorimetry (DSC) measurements. The changes of IR, SAXS, DSC, and WAXD results induced by annealing for etched samples have been compared with those for unetched ones. The IR absorbance spectrum of the quenched iPP etched by FNA did not change. In addition, the SAXS intensity did not increase when these samples were annealed, indicating that the total (IR) crystallinity (i.e., the content of chain segments in the helical conformations) of the etched samples does not increase. However, WAXD patterns of the samples changed in a manner similar to those of the unetched one, from the original two blurred diffraction peaks to the sharp crystal patterns of alpha-form iPP, suggesting that the mesomorphic (or liquid crystal-like) phase has reorganized to alpha-form crystals. It is concluded that the change of WAXD of quenched iPP films during annealing results mainly from transformation of order in the mesomorphic phase, rather than only from an increase of crystal size. In other words, mesomorphic-form iPP is not constituted by any known crystals (such as alpha or beta crystals) in small sizes; its WAXD pattern reflects truly the degree of order in the mesomorphic phase.

In-situ SAXS studies of the morphological changes of an alumina-zirconia-silicate ceramic during its formation

D Le Messurier, R Winter, CM Martin; J Appl Cryst 39 (2006) 589 Sponsorship: EPSRC, CCLRC, Pilkington

A novel activation mechanism for Clostridial bacteriophage endolysins

Bacteriophage-encoded endolysins are produced at the end of the phage lytic cycle for the degradation of the host bacterial cell. Endolysins offer the potential as alternatives to antibiotics as biocontrol agents or therapeutics. The lytic mechanisms of three bacteriophage endolysins that target Clostridium species living under different conditions were investigated. For these endolysins a trigger and release mechanism is proposed for their activation. During host lysis, holin lesion formation suddenly permeabilises the membrane which exposes the cytosol-sequestered endolysins to a sudden environmental shock. This shock is suggested to trigger a conformational switch of the endolysins between two distinct dimer states. The switch between dimer states is proposed to activate a novel autocleavage mechanism that cleaves the linker connecting the N-terminal catalytic domain and the C-terminal domain to release the catalytic domain for more efficient digestion of the bacterial cell wall. Crystal structures of cleaved fragments of CD27L and CTP1L were previously obtained. In these structures cleavage occurs at the stem of the linker connected to the C-terminal domain. Despite a sequence identity of only 22% between 81 residues of the C-terminal domains of CD27L and CTP1L, they represent a novel fold that is identified in a number of different lysins. Within the crystal structures the two distinct dimerization modes are represented: the elongated head‐on dimer and the side-by‐side dimer. Introducing mutations that inhibit either of the dimerization states caused a decrease in the efficiency of both the autocleavage mechanism and the lytic activity of the endolysins. The two dimer states were validated for the full-length endolysins in solution by using right angle light scattering, small angle X‐ray scattering and cross-linking experiments. Overall, the data represents a new type of regulation governed by the C-terminal domains that is used to activate these endolysins once they enter the bacterial cell wall.

Solution structure of the N-terminal transactivation domain of ERM modified by SUMO-1.

ERM is a member of the PEA3 group of the Ets transcription factor family that plays important roles in development and tumorigenesis. The PEA3s share an N-terminal transactivation domain (TADn) whose activity is inhibited by small ubiquitin-like modifier (SUMO). However, the consequences of sumoylation and its underlying molecular mechanism remain unclear. The domain structure of ERM TADn alone or modified by SUMO-1 was analyzed using small-angle X-ray scattering (SAXS). Low resolution shapes determined ab initio from the scattering data indicated an elongated shape and an unstructured conformation of TADn in solution. Covalent attachment of SUMO-1 does not perturb the structure of TADn as indicated by the linear arrangement of the SUMO moiety with respect to TADn. Thus, ERM belongs to the growing family of proteins that contain intrinsically unstructured regions. The flexible nature of TADn may be instrumental for ERM recognition and binding to diverse molecular partners.

Crystal and liquid crystalline polymorphism in 1-alkyl-3-methylimidazolium tetrachloropalladate(II) salts

1-Alkyl-3-methylimidazolium tetrachloropalladate(ii) salts ([C-n-mim](2)[PdCl4], n = 10, 12, 14, 16, 18) containing a single, linear alkyl-chain substituent on the cation have been synthesised and their behaviour characterised by differential scanning calorimetry, polarising optical microscopy and small-angle X-ray scattering. The salts display thermotropic polymorphism, exhibiting both crystal-crystal transitions and, for n = 14-18, the formation of a thermotropic smectic liquid crystalline phase.

Imidazolium ionic liquid crystals with pendant mesogenic groups

Ionic liquid crystals were obtained by coupling one or two mesogenic units (cholesterol or cyanobiphenyl) to an imidazolium cation. Anions are bromide, bis(trifluoromethylsulfonyl)imide, and tetrakis(2-thenoyltrifluoroacetonato)europate(III). The mesomorphism of the compounds depends on the type and number of mesogenic units and on the type of anion. In general, the most stable mesophases are observed for the bis(trifluoromethylsulfonyl)imide salts. Most of the compounds containing cholesterol moieties show enantiotropic SmA* phases over a broad temperature range, and some of them are room temperature liquid crystals. Modeling of the small-angle X-ray scattering patterns revealed the molecular arrangement in these mesophases. On the contrary, most of the compounds containing cyanobiphenyl groups exhibit monotropic lamellar or nematic mesophases, depending on the number of mesogenic units. The imidazolium salts containing the tetrakis(2-thenoyltrifluoroacetonato)europate(III) anion show an intense red photoluminescence.

Thermotropic Ruthenium(II)-Containing Metallomesogens Based on Substituted 1,10-Phenanthroline Ligands

Imidazo[4,5-f]-1,10-phenanthroline and pyrazino[2,3-f]-1,10-phenanthroline substituted with long alkyl chains are versatile ligands for the design of metallomesogens because of the ease of ligand substitution. Whereas the ligands and the corresponding rhenium(I) complexes were not liquid-crystalline, mesomorphism was observed for the corresponding ionic ruthenium(II) complexes with chloride, hexafluorophosphate, and bistriflimide counterions. The mesophases were identified as smectic A phases by high-temperature small-angle X-ray scattering (SAXS) using synchrotron radiation. The transition temperatures depend on the anion, the highest temperatures being observed for the chloride salts and the lowest for the bistriflimide salts. The ruthenium(II) complexes are examples of luminescent ionic liquid crystals.

Selective oxidation of a pyrimidine thioether using supported tantalum catalysts

Ta2O5-SiO2 catalysts were prepared by a sol-gel method using tetraethyl orthosilicate (TEOS) and tantalum (V) ethoxide as the sources of silicon and tantalum, and two families of quaternary ammonium salts, [CnH(2n+1)(CH3)(3)N]Br (n = 14, 16, 18) and [(CnH(2n+1))(4)N]Br (n = 10, 12, 16, 18) as surfactants. The catalysts were compared for the selective suffoxidation of 4,6-dimethyl-2-thiomethylpyrimidine using peroxide as an oxidising agent in a range of ionic liquids and organic solvents. The sol-gel catalysts were also compared with tantalum on MCM-41 prepared by grafting. The catalysts were characterized from adsorption-desorption isotherms of N-2, XRD patterns, small-angle X-ray scattering, IR spectra from adsorbed pyridine and CDCl3, XPS spectra, and Si-29 magic angle spinning (MAS) NNIR experiments. The effect of recycling on the catalyst leaching and selectivity/activity was also studied. High activities and selectivities were found in [NTf2](-) based ionic liquids and organic solvents with good recyclability of the catalyst. Tantalum was found in the solution after reaction; however, this was determined to be due to entrapment of catalyst particulates, as opposed to leaching of the active metal. (c) 2005 Elsevier Inc. All rights reserved.

Burkholderia cenocepacia BC2L-C Is a Super Lectin with Dual Specificity and Proinflammatory Activity

Lectins and adhesins are involved in bacterial adhesion to host tissues and mucus during early steps of infection. We report the characterization of BC2L-C, a soluble lectin from the opportunistic pathogen Burkholderia cenocepacia, which has two distinct domains with unique specificities and biological activities. The N-terminal domain is a novel TNF-alpha-like fucose-binding lectin, while the C-terminal part is similar to a superfamily of calcium-dependent bacterial lectins. The C-terminal domain displays specificity for mannose and L-glycero-D-manno-heptose. BC2L-C is therefore a superlectin that binds independently to mannose/heptose glycoconjugates and fucosylated human histo-blood group epitopes. The apo form of the C-terminal domain crystallized as a dimer, and calcium and mannose could be docked in the binding site. The whole lectin is hexameric and the overall structure, determined by electron microscopy and small angle X-ray scattering, reveals a flexible arrangement of three mannose/heptose-specific dimers flanked by two fucose-specific TNF-alpha-like trimers. We propose that BC2L-C binds to the bacterial surface in a mannose/heptose-dependent manner via the C-terminal domain. The TNF-alpha-like domain triggers IL-8 production in cultured airway epithelial cells in a carbohydrate-independent manner, and is therefore proposed to play a role in the dysregulated proinflammatory response observed in B. cenocepacia lung infections. The unique architecture of this newly recognized superlectin correlates with multiple functions including bacterial cell cross-linking, adhesion to human epithelia, and stimulation of inflammation.

Structure and dynamics of dextran in binary mixtures of a good and a bad solvent

The structure and dynamics of the common polysaccharide dextran have been investigated in mixed solvents at two different temperatures using small-angle X-ray scattering (SAXS) and viscosity measurements. More specifically, binary mixtures of a good solvent (water, formamide, dimethylsulfoxide, ethanolamine) and the bad solvent ethanol as the minority component have been considered. The experimentally observed effects on the polymer conformation (intrinsic viscosity, coil radius, and radius of gyration) of the bad solvent addition are discussed in terms of hydrogen bonding density and are correlated with the Hansen solubility parameters and the surface tension of the solvent mixtures. Hydrogen bonding appears to be an important contributor to the solubility of dextran but is not sufficient to capture the dextran coil contraction in the mixtures of good+bad solvents.

Híbridos orgânicos-inorgânicos para aplicações de baixo custo em óptica integrada

O objectivo desta tese é a utilização de materiais híbridos orgânicos-inorgânicos, designados por di-ureiasis modificados pela adição de tetra-propóxido de zircónio (Zr(i-OPr)4) estabilizado com ácido metacrílico (CH2=C(CH3)COOH), obtidos pela via sol-gel, para aplicações em dispositivos ópticos integrados de baixo custo. A estrutura local dos di-ureiasis com diferentes concentrações de propóxido de zircónio (20 a 80 % mol) foi estudada por difracção de raios-X, espalhamento de raios X a baixos ângulos, microscopia de força atómica, ressonância magnética nuclear dos núcleos dos átomos de 29Si e 13C, espectroscopia no infravermelho por transformada de Fourier, espectroscopia de Raman por transformada de Fourier e termogravimetria. A influência dos parâmetros de síntese, concentração de tetra propóxido de zircónio e rácio tetra propóxido de zircónio: ácido metacrilico na estrutura e propriedades das amostras em monólito e filmes finos (depositados pela técnica de deposição por rotação do substrato) foram avaliadas, permitindo obter amostras transparentes, fotopolimerizáveis e estáveis termicamente até aos 100 ºC. Foram determinadas as propriedades dos guias planares em substratos de vidro borosilicato e silício oxidado (1

Structural Diversity in Antibody Interactions with HIV-1 Env Immunogens

Thesis (Ph.D.)--University of Washington, 2013