Hygrothermal performance of wood-hemp insulation in timber frame wall panels with and without a vapour barrier

An in situ experiment on a full-scale timber frame test building was carried out to study the hygrothermal performance of wood-hemp composite insulation in timber frame wall panels with and without a vapour barrier. The heat transfer properties and the likelihood of mould growth and condensation in the panels were compared. Step changes in the internal relative humidity were performed to explore the effects of high, normal and low internal moisture loads on the wall panels. No significant difference in the average equivalent thermal transmittance (U-values) between the panels with and without a vapour barrier was observed. The average equivalent U-values of the panels were close to the U-values calculated from the manufacturers’ declared thermal conductivity values of the insulation. The likelihood of condensation was higher at the interface of the wood-hemp insulation and the oriented strand board (OSB) in the panel without a vapour barrier. In terms of the parametric assessment of the mould germination potential, the relative humidity, the temperature and the exposure conditions in the insulation-OSB interfaces of the panel without a vapour barrier were found to be more favourable to the germination of mould spores. Nonetheless, when the insulations were dismantled, no mould was visually detected.

Experimental and numerical evaluation of composite repairs on wood beams damaged by cross-graining

An experimental and Finite Element study was performed on the bending behaviour of wood beams of the Pinus Pinaster species repaired with adhesively-bonded carbon–epoxy patches, after sustaining damage by cross-grain failure. This damage is characterized by crack growth at a small angle to the beams longitudinal axis, due to misalignment between the wood fibres and the beam axis. Cross-grain failure can occur in large-scale in a wood member when trees that have grown spirally or with a pronounced taper are cut for lumber. Three patch lengths were tested. The simulations include the possibility of cohesive fracture of the adhesive layer, failure within the wood beam in two propagation planes and patch interlaminar failure, by the use of cohesive zone modelling. The respective cohesive properties were estimated either by an inverse method or from the literature. The comparison with the tests allowed the validation of the proposed methodology, opening a good perspective for the reduction of costs in the design stages of these repairs due to extensive experimentation.

Experimental Reinforcement of Wood Beams

Rehabilitation is becoming more and more usual in the construction sector in Portugal. The introduction of newer construction materials and technical know-how of integrating different materials for achieving desired engineering goals is an important step to the development of the sector. Wood industry is also getting more and more adapted to composite technologies with the introduction of the so called “highly engineered wood products” and with the use of modification treatments. This work is an attempt to explain the viability of using stainless steel and glass fibre reinforced polymer (GFRP) as reinforcements in wood beams. This thesis specifically focuses on the flexural behaviour of Portuguese Pine unmodified and modified wood beams. Two types of modification were used: 1,3-dimethylol-4,5- dihydroxyethyleneurea (DMDHEU) resin and amid wax. The behaviour of the material was analysed with a nonlinear model. The latter model simulates the behaviour of the reinforced wood beams under flexural loading. Small-scale beams (1:15) were experimented in flexural bending and the experimental results obtained were compared with the analytical model results. The experiments confirm the viability of the reinforcing schemes and the working procedures. Experimental results showed fair agreement with the nonlinear model. A strength increase between 15% and 80% was achieved. Stiffness increased by 40% to 50% in beams reinforced with steel but no significant increase was achieved with the glass fibre reinforcement.

Enhancement of ultrafiltration process by pretreatment in recovery of hemicelluloses from wood extracts

Hemicelluloses are potential raw material for several items produced in future wood-based biorefineries. One possible method for recovering hemicelluloses from wood extracts is ultrafiltration (UF). However, low filtration capacities and severe fouling restrict the use of tight UF membranes in the treatment of wood extracts. The lack of suitable commercial membranes creates a need for pretreatment which would decrease fouling and increase the filtration capacity. This thesis focuses on the evaluation of the possibility to improve the filtration capacity and decrease fouling with the pretreatment of wood extracts. Methods which remove harmful compounds and methods which degrade them are studied, as well as combinations of the methods. The tested pretreatments have an influence on both the concentration of different compounds and the molecular mass distribution of the compounds in the extract. This study revealed that in addition to which kind of compounds were removed, also the change in molecular size distribution affected the filtration capacity significantly. It was shown that the most harmful compounds for the filtration capacity of the hydrophobic 5 kDa membrane were the ones capable of permeating the membrane and fouling also the inner membrane structure. Naturally, the size of the most harmful compounds depends on the used UF membrane and is thus case-specific. However, in the choice of the pretreatment method, the focus should be on the removal of harmful compound sizes rather than merely on the total amount of removed foulants. The results proved that filtration capacity can be increased with both adsorptive and oxidative pretreatments even by hundreds of per cents. For instance, the use of XAD7 and XAD16 adsorbents increased the average flux in the UF of a birch extract from nearly zero to 107 kg/(m2h) and 175 kg/(m2h), respectively. In the treatment of a spruce extract, oxidation by pulsed corona discharge (PCD) increased the flux in UF from 46 kg/(m2h) to 158 kg/(m2h). Moreover, when a birch extract batch was treated with laccase enzyme, the flux in UF increased from 15 kg/(m2h) to 36 kg/(m2h). However, fouling was decreased only by adsorptive pretreatment while oxidative methods had a negligible or even negative impact on it. This demonstrates that filtration capacity and fouling are affected by different compounds and mechanisms. The results of this thesis show that filtration capacity can be improved and fouling decreased through appropriate pretreatment. However, the choice of the best possible pretreatment is case-specific and depends on the wood extract and the membrane used. Finding the best option requires information on the extract content and membrane characteristics as well as on the filtration performance of the membrane in the prevailing conditions and a multivariate approach. On the basis of this study, it can be roughly concluded that adsorptive pretreatment improves the filtration capacity and decreases fouling rather reliably, but it may lead to significant hemicellulose losses. Oxidation reduces the loss of valuable hemicelluloses and could improve the filtration capacity, but fouling challenges may remain. Combining oxidation with adsorptive pretreatment was not a solution for avoiding hemicellulose losses in the tested cases.

The efficacy of anti-predator behaviour in the wood fog tadpole (Rana sylvatica) /

Activity has been suggested as an important behaviour that is tightly linked with predator avoidance in tadpoles. In this thesis I examine predator-prey relationships using wood frog tadpoles {Rana sylvaticd) as prey and dragonfly larvae {AnaxJunius) and backswimmers {Notonecta undulatd) as predators. I explore the role of prey activity in predator attack rates, prey response to single and multiple predator introductions, and prey survivorship. The data suggest that Anax is the more successful predator, able to capture both active and inactive tadpoles. In contrast, Notonecta strike at inactive prey less frequently and are seldom successftil when they do. A mesocosm study revealed that the presence of any predator resulted in reduced activity level of tadpoles. Each predator species alone had similar effects on tadpole activity, as did the combined predator treatment. Tadpole survivorship, however, differed significantly among both predator treatments and prey populations. Tadpwles in the combined predator treatment had enhanced risk; survivorship was lower than that expected if the two predators had additive effects. Differences in survivorship among wood frog populations showed that tadpoles from a lake habitat had the lowest survivorship, those from a shallow pond habitat had an intermediate survivorship, and tadpoles from a marsh habitat had the highest survivorship. The frequency of interactions with predators in the native habitat may be driving the population differences observed. In conclusion, results from this study show that complex interactions exist between predators, prey, and the environment, with activity playing a key role in the survival of tadpoles.

Welland Canal Survey of Lands Samuel Wood Esquire, 1828

Survey map and description of Samuel Wood's land created by The Welland Canal Company. Included is a written description of the land along with a drawing of the land. The same description of the land is also in a deed dated Septmeber 16, 1828 (see county registry 739). Noteable features include; the canal, the tow path, the tow path bridge. Surveyor notes are seen in pencil on the map. The original deed for the land is dated May 16, 1828.

Joanna E. Wood short stories, 1898-1900

Joanna Ellen Wood (1867-1927) was an acclaimed Canadian author who wrote several novels and short stories. Wood was born in Scotland, but emigrated to Canada with her family in 1869. In 1874 her father purchased a farm overlooking the Niagara River at Queenston. It is believed she was supported by her brother William, who encouraged her writing. She was based in New York City from 1887-1901, using William’s business address there to receive correspondence while she traveled or spent time in Queenston. Around 1906, Wood moved with her mother to Niagara-on-the-Lake, where she joined the Niagara Historical Society. By 1914, she was living in Buffalo, but later spent time at her sisters’ homes. It was at her sister’s home in Detroit where she suffered a stroke and died in 1927. Wood’s literary career was short-lived. She published her first novel, The Untempered Wind , in 1894, and a second novel, Judith Moore …, in 1898. Both novels received critical acclaim, and a third novel, Farden Ha', followed in 1902. Unfortunately the majority of Wood’s numerous and award-winning writings cannot be found. Her career peaked in 1901, when she was the highest paid Canadian fiction writer. For unknown reasons, her career abruptly ceased in 1902, with no further publications or mention made of her in the Canadian Magazine.

Letter to the Honourable William Dickson at Wood Lawn, Youngstown, New York from W. Bushby

Letter to the Honourable William Dickson at Wood Lawn, Youngstown, New York from W. Bushby. He says that Mary is probably going to marry Mr. Lyon and he asks if there is any chance that Mr. Dickson could come for the wedding. He says he heard about the death of George Hamilton from John Hamilton (3 ½ pages, handwritten), Sept. 29, 1836.

Inventory of goods and chattels belonging to Samuel Wood and delivered to the Honourable William Dickson

Inventory of goods and chattels belonging to Samuel Wood and delivered to the Honourable William Dickson (double-sided, handwritten page), Dec. 10, 1828.

Rubber Solution Adhesives for Wood-to-Wood Bonding

Rubber solutions were prepared and used for bonding wood pieces. The effect of the variation of chlorinated natural rubber (CNR) and phenolformaldehyde (PF) resin in the adhesive solutions on lap shear strength was determined. Natural rubber and neoprene-based adhesive solutions were compared for their lap shear strength. The storage stability of the adhesive prepared was determined. The change in lap shear strength before and after being placed in cold water, hot water, acid, and alkali was tested. The bonding character of these adhesives was compared with different commercially available solution adhesives. The room-temperature aging resistance of wood joints was also determined. In all the studies, the adhesive prepared in the laboratory was found to be superior compared to the commercial adhesives.

Environmental Impacts of Chromated Copper Arsenate (CCA) Treated Rubber Wood for Aquatic Applications

Faculty of Marine Sciences, Cochin University of Science and Technology

Chromated Copper Arsenate (CCA) Treatment for Rubber Wood Preservation and its Impact on the Aquatic Biota

Faculty of Marine Sciences, Cochin University of Science and Technology