Magnetic field design for floating zone crystal growth

The magnetic fields produced by electrical coils are designed for P-doped Si crystal growth in a floating full zone in microgravity environment. The fields are designed specially to reduce the how near the free surface and then in the melt zone by adjusting the coil positions near the melt zone. The effects of the designed magnetic fields on reducing the Row velocity and the non-uniformity of the concentration distribution in the melt zone are better than those of the case of a uniform longitudinal magnetic field, obtained by numerical simulation. It is expected to improve the radial macro-segregation and reduce the convection in the crystal growth at the same time by using the designed magnetic field.

Semi-insulating layer for novel high voltage polysilicon thin film transistors

This work describes the deposition and characterisation of semi-insulating oxygen-doped silicon films for the development of high voltage polycrystalline silicon (poly-Si) circuitry on glass. The performance of a novel poly-Si High Voltage Thin Film Transistor (HVTFT) structure, incorporating a layer of semi-insulating material, has been investigated using a two dimensional device simulator. The semi-insulating layer increases the operating voltage of the HVTFT structure by linearising the potential distribution in the device offset region. A glass compatible semi-insulating layer, suitable for HVTFT applications, has been deposited by the Plasma Enhanced Chemical Vapour Deposition (PECVD) technique from silane (SiH4), nitrous oxide (N2O) and helium (He) gas mixtures. The as-deposited films are furnace annealed at 600°C which is the maximum process temperature. By varying the N2O/SiH4 ratio the conductivity of the annealed films can be accurately controlled up to a maximum of around 10-7 Ω-1cm-1. Helium dilution of the reactant gases improves both film uniformity and reproducibility. Raman analysis shows the as-deposited and annealed films to be completely amorphous. A model for the microstructure of these Semi-Insulating Amorphous Oxygen-Doped Silicon (SIAOS) films is proposed to explain the observed physical and electrical properties.

Low-temperature (≤600 °C) semi-insulating oxygen-doped silicon films by the PECVD technique for large-area power applications

This work describes the deposition, annealing and characterisation of semi-insulating oxygen-doped silicon films at temperatures compatible with polysilicon circuitry on glass. The semi-insulating layers are deposited by the plasma enhanced chemical vapour deposition technique from silane (SiH4), nitrous oxide (N2O) and helium (He) gas mixtures at a temperature of 350 °C. The as-deposited films are then furnace annealed at 600 °C which is the maximum process temperature. Raman analysis shows the as-deposited and annealed films to be completely amorphous. The most important deposition variable is the N2O SiH4 gas ratio. By varying the N2O SiH4 ratio the conductivity of the annealed films can be accurately controlled, for the first time, down to a minimum of ≈10-7Ω-1cm-1 where they exhibit a T -1 4 temperature dependence indicative of a hopping conduction mechanism. Helium dilution of the reactant gases is shown to improve both film uniformity and reproducibility. A model for the microstructure of these semi-insulating amorphous oxygen-doped silicon films is proposed to explain the observed physical and electrical properties. © 1995.

Low temperature (≤ 600°C) semi-insulating oxygen-doped silicon films by the PECVD technique for large area power applications

This work describes the annealing and characterisation of semi-insulating oxygen-doped silicon films deposited by the Plasma Enhanced Chemical Vapour Deposition (PECVD) technique from silane (SiH4), nitrous oxide (N2O) and helium (He) gas mixtures. The maximum process temperature is chosen to be compatible with large area polycrystalline silicon (poly-Si) circuitry on glass. The most important deposition variable is shown to be the N2O SiH4 gas ratio. Helium dilution results in improved film uniformity and reproducibility. Raman analysis shows the 'as-deposited' and annealed films to be completely amorphous. A model for the microstructure of these Semi-Insulating Amorphous Oxygen-doped Silicon (SIAOS) films is proposed to explain the observed physical and electrical properties. © 1995.

Microfabrication and application of reservoir pins for liquid transfer in biotechnology

Microarraying involves laying down genetic elements onto a solid substrate for DNA analysis on a massively parallel scale. Microarrays are prepared using a pin-based robotic platform to transfer liquid samples from microtitre plates to an array pattern of dots of different liquids on the surface of glass slides where they dry to form spots diameter < 200 μm. This paper presents the design, materials selection, micromachining technology and performance of reservoir pins for microarraying. A conical pin is produced by (i) conventional machining of stainless steel or wet etching of tungsten wire, followed by (ii) micromachining with a focused laser to produce a microreservoir and a capillary channel structure leading from the tip. The pin has a flat end diameter < 100 μm from which a 500 μm long capillary channel < 15 μm wide leads up the pin to a reservoir. Scanning electron micrographs of the metal surface show roughness on the scale of 10 μm, but the pins nevertheless give consistent and reproducible spotting performance. The pin capacity is 80 nanolitres of fluid containing DNA, and at least 50 spots can be printed before replenishing the reservoir. A typical robot holds can hold up to 64 pins. This paper discusses the fabrication technology, the performance and spotting uniformity for reservoir pins, the possible limits to miniaturization of pins using this approach, and the future prospects for contact and non-contact arraying technology.

Properties of a-C:H films deposited from a methane electron cyclotron wave resonant plasma

An electron cyclotron wave resonant methane plasma discharge was used for the high rate deposition of hydrogenated amorphous carbon (a-C:H). Deposition rates of up to ∼400 Å/min were obtained over substrates up to 2.5 in. in diameter with a film thickness uniformity of ∼±10%. The deposited films were characterised in terms of their mass density, sp3 and hydrogen contents, C-H bonding, intrinsic stress, scratch resistance and friction properties. The deposited films possessed an average sp3 content, mass density and refractive index of ∼58%, 1.76 g/cm3 and 2.035 respectively.Mechanical characterisation indicated that the films possessed very low steady-state coefficients of friction (ca. 0.06) and a moderate shear strength of ∼141 MPa. Nano-indentation measurements also indicated a hardness and elastic modulus of ∼16.1 and 160 GPa respectively. The critical loads required to induce coating failure were also observed to increase with ion energy as a consequence of the increase in degree of ion mixing at the interface. Furthermore, coating failure under scratch test conditions was observed to take place via fracture within the silicon substrate itself, rather than either in the coating or at the film/substrate interface. © 2003 Elsevier B.V. All rights reserved.

Plasma enhanced chemical vapour deposition carbon nanotubes/nanofibres - How uniform do they grow?

The ability to grow carbon nanotubes/nanofibres (CNs) with a high degree of uniformity is desirable in many applications. In this paper, the structural uniformity of CNs produced by plasma enhanced chemical vapour deposition is evaluated for field emission applications. When single isolated CNs were deposited using this technology, the structures exhibited remarkable uniformity in terms of diameter and height (standard deviations were 4.1 and 6.3% respectively of the average diameter and height). The lithographic conditions to achieve a high yield of single CNs are also discussed. Using the height and diameter uniformity statistics, we show that it is indeed possible to accurately predict the average field enhancement factor and the distribution of enhancement factors of the structures, which was confirmed by electrical emission measurements on individual CNs in an array.

Multi-colour switching of polymer stabilized chiral nematic liquid crystal devices

We have fabricated a series of polymer stabilized chiral nematic test cells for use as flexoelectro-optic devices. The devices fabricated were based on commercial chiral nematic mixtures which were polymer stabilized so as to enhance the uniformity and stability of the uniform lying helix texture in the cells. During fabrication and test procedures a series of unusual scattering states have been observed within the devices at different viewing angles. The observations made so far indicate that the properties of the scattering state lies somewhere between the focal conic texture and the Grandjean or planar texture and that the devices exhibit both a helical pitch selective reflection and scattering effect. What is even more dramatic is that the wavelength selectivity of the scattering effect can be tuned by an applied field. In addition, we show that it is possible to achieve good uniform lying helix textures from such devices. Moreover, we show that in certain cases the spontaneous alignment of the helix in the plane of the device opens up the possibility of a new mode of switching. Flexoelectric, Redshift, Coloured scattering, Liquid crystal, Polymer-stabilized liquid-crystal;.

Interface Layer Effect On The Stress Distribution Of A Wafer-Bonded Bilayer Structure

The interface layer plays an important role in stress transfer in composite structures. However, many interface layer properties such as the modulus, thickness, and uniformity are difficult to determine. The model developed in this article links the influence of the interface layer on the normal stress distribution along the layer thickness with the layer surface morphology before bonding. By doing so, a new method of determining the interfacial parameter(s) is suggested. The effects of the layer thickness and the surface roughness before bonding on the normal stress distribution and its depth profile are also discussed. For ideal interface case with no interfacial shear stress, the normal stress distribution pattern can only be monotonically decreased from the interface. Due to the presence of interfacial shear stress, the normal stress distribution is much more complex, and varies dramatically with changes in the properties of the interface layer, or the dimensions of the bonding layers. The consequence of this dramatic stress field change, such as the shift of the maximum stress from the interface is also addressed. The size-dependent stress distribution in the thickness direction due to the interface layer effect is presented. When the interfacial shear stress is reduced to zero, the model presented in this article is also demonstrated to have the same normal stress distribution as obtained by the previous model, which does not consider the interface layer effect.

Concentration distribution in crystallization from solution under microgravity

Concentration distribution in crystallization from solution under microgravity is numerically studied. A quasi-steady state growth and dissolution in a 2D rectangular enclosure filled with sodium chlorate (NaClO3) aqueous solution, in which one wall is the growth surface of the crystal and the opposite one is the dissolution surface, is considered. The solute transport process at the growth surface is described by the diffusion-reaction theory with finite interface kinetics coefficient. The results show that the concentration at the growth surface is supersaturated and the supersaturation distribution is of non-uniformity, i.e. the supersaturation in a region facing an incoming flow is high. On the other hand, the non-uniformity of supersaturation at the growth surface is closely related to the gravity level even under microgravity, it exponentially increases as the thermal Rayleigh number on behalf of the gravity level rises.

A contribuição da Legimática para a qualidade formal do texto legislativo

O objetivo deste trabalho é identificar como as ferramentas propostas pela Legimática podem contribuir para diminuir as deficiências dos textos legislativos apontadas pela Legística. A preocupação com o processo de criação e com a qualidade do texto legislativo por ele produzido é o foco principal da Legística Formal. Esta atividade encontra amparo nas ferramentas propostas pela Legimática que auxiliam a elaboração de normas legais por meio de processadores eletrônicos de textos concebidos especificamente para este propósito, ou seja, redação de leis. Tais ferramentas garantem o emprego de regras formalmente estabelecidas para um texto legal, e de forma mais abrangente, facilitam a clareza, o rigor e a uniformidade da linguagem legislativa do documento produzido. A realização de pesquisas qualitativa e bibliográfica permitiu propor a criação de um software que auxilie no processo de elaboração normativa dos órgãos legislativos federais brasileiros baseando-se em considerações de especialistas, análise de ferramentas semelhantes e referências na literatura.

Two Bubbles Thermocapillary Migration Experimental System

An experimental investigation will be performed on the thermocapillary motion of two bubbles in Chinese return-satellite. The experiment will study the migration process of bubble caused by thermocapillary effect in microgravity environment, and their interaction between two bubbles. The bubble is driven by the thermocapillary stress on the surface on account on the variation of the surface tension with temperature. The interaction between two bubbles becomes significant as the separation distance between them is reduced drastically so that the bubble interaction has to be considered. Recently, the problem has been discussed on the method of successive reflections, and accurate migration velocities of two arbitrarily oriented bubbles were derived for the limit of small Marangoni and Reynolds numbers. Numerical results for the migration of the two bubbles show that the interaction between two bubbles has significant influence on their thermocapillary migration velocities with a bubble approaching another. However, there is a lack of experimental validate for the theoretic results. Now the experimental facility is designed for experimenting time after time. A cone-shaped top cover is used to expel bubble from the cell after experiment. But, the cone-shaped top cover can cause temperature uniformity on horizontal plane in whole cell. Therefore, a metal board with multi-holes is fixed under the top cover. The board is able to let the temperature distribution on the board uniform because of their high heat conductivity, and the bubble can pass through it. In the system two bubbles are injected into the test cell respectively by two sets of cylinder. And the bubbles sizes are controlled by two sets of step-by-step motor. It is very important problem that bubble can be divorced from the injecting mouth in microgravity environment. Thus, other two sets of device for injecting mother liquid were used to push bubble. The working principle of injecting mother liquid is to utilize pressure difference directly between test cell and reservoir

Experimental Studies on Scramjet Tested in a Freejet Facility

Two different type scramjet models with side-wall compression and top-wall compression inlets have been tested in HPTF (Hypersonic Propulsion Test Facility) under the experimental conditions of Mach number 5.8, total temperature 1700K, total pressure 4.5MPa and mass flow rate 3.5kg/s. The liquid kerosene was used as main fuel for the scramjets. In order to get fast ignition in the combustor, a small amount of hydrogen was used as a pilot. A strut with alternative tail was employed for increasing the compression ratio and for mixing enhancement in the side-wall compression case. Recessed cavities were used as a flameholder for combustion stability. The combustion efficiency was estimated by one dimensional theory. The uniformity of the facility nozzle flow was verified by a scanning pitot rake. The experimental results showed that the kerosene fuel was successfully ignited and stable combustion was achieved for both scramjet models. However the thrusts were still less than the model drags due to the low combustion efficiencies.

Shock-Induced Dust Cloud Over a Deposit Layer of Fine Particles

The present paper investigates particle density pro les of a dust cloud induced by a normal shock wave moving at a constant speed along a at surface deposited with ne particles. In shock-fixxed coordinates, numerical simulation of ow structures of the carrier- and dispersed- phases was performed for the M = 2 case. The neness and non-uniformity of the particle size are taken into account and their effcts on the dust cloud are discussed in detail.

A quantitative analysis of the phytoplankton of the Gulf of Panama: I. Results of the regional phytoplankton surveys during July and November 1957 and March 1958

ENGLISH: 1. Quantitative phytoplankton samples were collected by the Inter-American Tropical Tuna Commission at the surface and ten meters in the Gulf of Panama, as follows: a) 18-21 March, 1958 (31 stations)-during the height of the upwelling season, b) 10-12 July, 1957 (10 stations)-during the transition to the rainy season at a time when mild upwelling winds reappear, c) 7-8 November, 1957 (15 stations)-during the height of the rainy season. 2. Maximum phytoplankton populations occurred during the upwelling season, followed by a considerable decline during July, and a further Subsidence during November. 3. A remarkable regional uniformity in species composition was observed during the surveys despite regional differences in growth conditions. Diatoms overwhelmingly dominated the communities. 4. During all surveys, the innermost regions, generally north of 8°30'N, were the most productive. The least productive areas were in the offing of San Miguel Bay and Parita Bay, suggesting that nutrient accretion via runoff is inadequate to sustain sizeable autotrophic plant populations in those regions. 5. During all surveys, phytoplankton growth appeared to be limited by nutrient availability. 6. During all surveys, phytoplankton growth appeared to be related to depth of the water column. 7. Although below average rainfall contributed to unusually favorable growth conditions (reduced stability, increased transparency and, presumably, nutrient reserves) during the November survey relative to November 1955 and 1956 at 8°45'N, 79°23'W, the anticipated heightened phytoplankton response was not observed. 8. During the November survey, the local diatom responses and their regional fluctuations could be satisfactorily related to the accompanying surface salinity conditions. However, this correspondence is undoubtedly attributable to factors associated with the observed salinity levels, probably nutrients, rather than salinity directly. 9. Unusually warm conditions occurred during the March survey, attributable to considerably weaker upwelling winds than normally occurring then, which contributed to a considerably lower standing crop and a retardation in succession of three to five weeks relative to that observed during 1955-1957 at 8°45'N, 79°23'W in the Gulf of Panama. 10. During the March survey, a well defined inverse relationship existed between mean temperature and mean diatom abundance in the upper ten meters, and between transparency and mean diatom abundance. A direct relationship occurred between surface salinity and mean diatom abundance in the upper ten meters. These relationships are interpreted to indicate that diatom abundance primarily reflected the nutrient concentrations associated with a given upwelling intensity, rather than describing casual relationships. 11. The survey results indicate that the phytoplankton dynamics observed at 8°45'N, 79°23'W from November, 1954 through May, 1957 are generally representative of the Gulf of Panama. 12. The following new forms, to be described in a later publication, were observed during the surveys: Actinoptychus undulatus f. catenata n.f., Asterionella japonica f. tropicum n.f., Leptocylindrus maximus n. sp., Skeletonema costatum f. tropicum n.f. SPANISH: 1. La Comisión Interamericana del Atun Tropical recolectó en el Golfo de Panama muestras cuantitativas de fitoplancton en la superficie y a los diez metros, como sigue: a) Del 18 al 21 de marzo de 1958 (31 estaciones)-durante el maximum de la estación de afloramiento. b) Del 10 al 12 de julio de 1957 (10 estaciones)-durante la epóca de transición a la estación lluviosa cuando reaparecen los vientos ligeros que causan el afloramiento. c) Del 7 al 8 de noviembre de 1957 (15 estaciones)-durante el maximum de la estación lluviosa. 2. Las poblaciones maximas de fitoplancton aparecieron durante la estación de afloramiento, seguido por una considerable disminución durante el mes de julio y una calma durante noviembre. 3. Durante la investigación se observó una remarcable uniformidad regional en la composición de las especies a pesar de las diferencias regionales en las condiciones de crecimiento. Las diatomeas predominaban en gran numero en las comunidades. 4. Durante todas las investigaciones, las regiones mas cerca de la costa, generalmente al norte de los 8°30'N, eran las mas productivas. Las areas menos productivas fueron las mar afuera de las Bahias de San Miguel y Parita, lo que sugiere que el aumento en las sales nutritivas causado por las escorrentias es inadecuado para sostener poblaciones grandes de plantas autotróficas en estas regiones. 5. Durante todas las investigaciones, el crecimiento del fitoplancton parecio estar limitado por la disponibilidad de las. sales nutritivas. 6. Durante todas las investigaciones el crecimiento del fitoplancton parecio estar relacionado con la profundidad de la columna de agua. 7. Aunque las precipitacion por debajo del promedio normal contribuyo a condiciones desusadamente favorables de crecimiento (estabilidad reducida, aumento de la transparencia y, presumiblemente, de la reserva de sales nutritivas) durante la investigación de noviembre en relación a noviembre de 1955 y de 1956 en los 8°45'N, 79°23'W, no se observo-la alta reacción de fitoplancton que se esperaba. 8. Durante la investigación de noviembre, las reacciones locales de las diatomeas y sus fluctuaciones regionales pudieron relacionarse en forma satisfactoria con condiciones asociadas con la salinidad de la superficie. Sin embargo, esta correspondencia puede atribuirse sin duda a factores asociados con los niveles observados de salinidad, probablemente con las sales nutritivas, en lugar de directamente con la salinidad. 9. Condiciones calurosas no comunes ocurrieron durante la investigación de marzo, las que pueden atribuirse a que los vientos que ocasionan el afloramiento fueran mas debiles que los normales, lo que contribuyó a que la cosecha estable fuera considerablemente mas baja y a la demora de tres a cinco semanas en la sucecion relativa a la que se observó durante 1955-1957 en los 8°45'N, 8°23'W, en el Golfo de Panama. 10. Durante la investigación de marzo, existió una relación inversa bien definida entre la temperatura y la abundancia media de las diatomeas en los diez metros superiores, y entre la transparencia y la abundancia media de las diatomeas. Una relación directa ocurrio entre la salinidad de superficie y la abundancia media de las diatomeas en los diez metros superiores. Estas relaciones se interpretan como indicadoras de que la abundancia de diatomeas refleja primeramente las concentraciones de las sales nutritivas asociadas con una intensidad de afloramiento dada, en lugar de describir relaciones causales. 11. Los resultados de la investigacion indican que la dinamica del fitoplancton observada en los 8°45'N, 79°23'W, desde noviembre de 1954 a mayo de 1957, es generalmente representativa del Golfo de Panama. 12. Durante las investigaciones se observaron las siguientes formas nuevas, las que seran descritas en una publicación posterior: Actinoptychus undulatus f. catenata n.f., Asterionella japonica f. tropicum n.f., Leptocylindrus maximus n. sp., Skeletonema costatum f. tropicum n.f.