Estudo radiográfico digital e densitométrico em mandíbulas de suínos, submetidas a osteotomia com brocas de alta e baixa rotação, com refrigeração líquida

Pós-graduação em Odontologia - FOA

Osteotomia com brocas de alta e baixa rotação, com e sem refrigeração líquida: estudo histopatológico duplo cego em suínos

Pós-graduação em Odontologia - FOA

Efeito do ultra-som de baixa potência na reparação óssea em ratos sob ausência de carga: análise densitométrica e biomecânica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influência do laser terapêutico no reparo de defeito ósseo de ratos submetidos à ausência de carga

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Expressão dos fatores de crescimento obtidos do plasma rico em plaquetas, no tratamento de fraturas experimentais do radio de cães

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação histológica e histomorfométrica do reparo ósseo em tíbias osteotomizadas de ratos (Rattus novergicus albinus) frente à ausência de carga e tratamento com ultrassom

Pós-graduação em Ciência Animal - FMVA

Avaliação da reparação de feridas cutâneas e ósseas realizadas por técnicas convencionais e com laser de Er, Cr:YSGG: estudo em ratos

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Avaliação de substitutos ósseos em defeitos peri-implantares criados em coelhos

Pós-graduação em Odontologia - FOA

Artroplastia total modular híbrida da articulação coxofemoral: estudo experimental em cães

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação da reação periodontal na técnica de colagem extra-alveolar de fraturas radiculares verticais simuladas: estudo histológico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Reparação óssea após osteotomia com brocas de alta e baixa rotação e refrigeração líquida: estudo histológico comparativo entre tecido ósseo alveolar e extra-alveolar em suínos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Gliding Mentoplasty: A New Technique

The goal of mentoplasty is to improve chin projection. Traditionally, this is accomplished by either mandibular osteotomy or alloplastic implants. However, these procedures are not free of complications. This report describes gliding mentoplasty, a novel, simple technique for chin projection.The 12 patients in this study underwent gliding mentoplasty. By means of a 2-cm intraoral incision, a subcutaneous dissection was made in the caudal direction. The dissection then proceeded in the subperiosteal plane, leaving a 1-cm cuff of muscle attached to the bone, and advanced toward the lower border of the chin. Subsequently, the dissection was extended laterally, and the whole mental area was dissected from the surrounding tissue. Three 2-0 monofilament nylon sutures were placed in the submandibular periosteum and connected through the remaining muscle cuff to the periosteum. These key sutures allowed the submandibular region to slide forward, project the subcutaneous tissue and mentalis muscle, define the labiomental fold, and improve the pogonion projection.Gliding mentoplasty resulted in a symmetric projection of the chin in all cases. In two patients, a submandibular dimple developed, which spontaneously resolved in 1 month. No revision surgery was performed, and no tissue relapse was noted. The mean follow-up period was 24.7 +/- A 5.17 months (range 19-33 months). All the patients were satisfied with the result.Gliding mentoplasty is a simple, easy-to-perform, rapid surgical technique of chin projection that produces low pain, rapid recovery, and excellent cosmetic results.This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266.

Investigation of the effect of movement and irrigation systems on temperature in the conventional drilling of cortical bone

We have compared the results of the external irrigation technique with those of a double irrigation technique with continuous intermittent movement. Maximum thermal measurements were made in the cortical part of 10 samples of bovine ribs during osteotomy to simulate the preparation of a surgical bed for the installation of dental implants at a depth of 10 mm Twenty specimens were drilled for each group: external irrigation and continuous movement (control group 1, CG1); external irrigation and intermittent movement (control group 2, CG2); double irrigation and continuous movement (test group 1, TG1); and double irrigation and intermittent movement (test group 2, TG2). The double irrigation technique gave significantly better results regardless of the drilling movement used. Thermal increases between samples was 19.2% in group CG1, 10.4% in CG2, 5.4% in TG1, and 3.4% in TG2. The double irrigation technique produced a significantly smaller increase in temperature in the cortical bone during both types of drilling (p = 0.001), which illustrated its greater efficiency compared with that of the external irrigation technique. (C) 2013 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Orthognathic surgery with or without induced hypotension

This study involved a retrospective evaluation of patients subjected to surgery for dentofacial deformities treated without induced controlled hypotension (group I, n = 50) and a prospective evaluation of patients who were subjected to surgery under hypotensive general anaesthesia (group II, n = 50). No statistical differences were found between the study groups with regard to the duration of surgery. However, there were statistically significant differences in the need for blood transfusion and the occurrence of bradycardia during the maxillary down-fracture. Hypotensive anaesthesia decreased the need for a blood transfusion and the occurrence of bradycardia, and is therefore considered highly beneficial for patients undergoing orthognathic surgery.

Influence of Implant Drill Materials on Wear, Deformation, and Roughness After Repeated Drilling and Sterilization

Purpose:The aim of this study was to evaluate deformation, roughness, and mass loss of stainless steel, diamond-like carbon (DLC)-coated and zirconia drills after multiple osteotomies with sterilization procedures.Materials and Methods:Drilling procedures were performed using stainless steel (G1), DLC-coated (G2), and zirconia (G3) drills. All groups were divided in subgroups 1, 2, 3, 4, and 5, corresponded to drills used 0, 10, 20, 30, and 40 times, respectively.Results:No significant differences in mass and roughness were detected among all groups and subgroups. In SEM images, all groups revealed signs of wear while coating delamination was detected in G2. Drills from G1 displayed more irregular surface, whereas cutting edges were more regular in G3.Conclusion:Zirconia drills presented more regular surfaces whereas stainless steel drills revealed more severe signs of wear. Further studies must be performed to evaluate the putative influence of these findings in heat generation.