Thermal decomposition of hydrazinium aluminium sulfate hydrate and hydrazinate

Abstract is not available.

Performance of graphic aluminium particulate composite materials

Friction characteristics of journal bearings made from cast graphic aluminum particulate composite alloy were determined under mixed lubrication and compared with those of the base alloy (without graphite) and leaded phosphor bronze. All three materials ran without seizure while the performance of the particulate composite and leaded phosphor bronze improved with running. Temperature rise in the journal bearing under mixed/boundary lubrication was also measured. It was found that with 0.3D/1000 to 1.5D/1000 clearance and a low lubrication rate (typical value for a bearing of diameter 35 mm × length 35 mm is 80 mm3/min) and at a PV value of 73 × 106 Nm m−2 min−1 graphitic aluminium alloy journal bearings operate satisfactorily without seizure and excessive temperature rise. In comparison, the bronze bearings, with all the other parameters remaining the same, could not run without excessive temperature rise at clearances below D/1000 at lubrication rates lower than 200 mm3/min

The machinability of a cast aluminium alloy-graphite particle composite

The microstructure of a cast Al---Si alloy-graphite particle composite is examined using optical and analytical scanning electron microscopy. Specimens containing different percentages of graphite were machined by orthogonal planning with 25° and 45° rake angle tools at both 6.5 and 13.2 m min−1. The machining forces are reported and the chip-rake-face friction coefficients and shear flow stresses are calculated. It is shown that the reduction in machining forces with increasing graphite content is due mostly to a decrease in the shear flow stress rather than to lower chip-rake-face friction. Both the polished and the machined surfaces of the composite are rougher than those of the simple alloy, apparently owing to the greater porosity, the tearing out of graphite particles, or the opening of cracks at the graphite particles in the wake of the tool.

On the Kelvin-Helmholtz instability of structured plasma layers in the magnetosphere

The hydromagnetic Kelvin-Helmholtz (K-H) instability problem is studied for a three-layered system analytically by arriving at the marginal instability condition. As the magnetic field directions are taken to vary in the three regions, both the angle and finite thickness effects are seen on the instability criterion. When the relative flow speed of the plasmas on the two sides of the interfaces separating the inner and the surrounding layers is U < Uc, where Uc is the critical speed, the system is stable both for symmetric and asymmetric perturbations. However, unlike the case of the interface bounded by two semiinfinite media, Uc is no longer the minimum critical speed above which the system will be unstable for all wavenumbers; another critical speed U* > Uc is introduced due to the finiteness of the system. When Uc < U < U*, the instability can set in either through the symmetric or asymmetric mode, depending on the ratio of the plasma parameters and angle between the magnetic field directions across the boundaries. The instability arises for a finite range of wavenumbers, thus giving rise to the upper and lower cut-off frequencies for the spectra of hydromagnetic surface waves generated by the K-H instability mechanism. When U > U*, both the modes are unstable for short wavelengths. The results are finally used to explain some observational features of the dependence of hydromagnetic energy spectra in the magnetosphere on the interplanetary parameters.

Wear characteristics and bearing performance of aluminium-mica particulate composite material

Some tribological properties of a mica-dispersed Al-4%Cu-1.5%Mg alloy cast by a conventional foundry technique are reported. The effect of mica dispersion on the wear rate and journal bearing performance of the matrix alloy was studied under different pressures and under different interface friction conditions. The dispersion of mica was found (a) to increase the wear rate of the base alloy, (b) to decrease the temperature rise during wear and (c) to improve the ability of the alloy to resist seizure.

Observation of kink shear bands in an aluminium single crystal fracture specimen

The near-tip deformation field in a high-constraint three-point bend specimen of pure aluminium single crystal is studied using in situ electron back-scattered diffraction and optical metallography. The orientation considered has the notch lying on the (0 1 0) plane and the notch front along direction. Results clearly show the occurrence of a kink shear sector boundary at 90° to the notch line on the specimen free surface as predicted by the analytical model of Rice [J.R. Rice, Mech. Mater. 6 (1987) 317].

Preparation of cast aluminium alloy-mica particle composites

The optimum conditions for producing cast aluminium alloy-mica particle composites, by stirring mica particles (40 to 120 mgrm) in molten aluminium alloys (above their liquidus temperatures), followed by casting in permanent moulds, are described. Addition of magnesium either as pieces along with mica particles on the surface of the melts or as a previously added alloying element was found to be necessary to disperse appreciable quantities (1.5 to 2 wt.%) of mica particles in the melts and retain them as uniform dispersions in castings under the conditions of present investigation. These castings can be remelted and degassed with nitrogen at least once with the retention of about 80% mica particles in the castings. Electron probe micro-analysis of these cast composites showed that magnesium added to the surface of the melt along with mica has a tendency to segregate around the mica particles, apparently improving the dispersability for mica particles in liquid aluminium alloys. The mechanical properties of the aluminium alloy-mica particle composite decrease with an increase in mica content, however, even at 2.2% the composite has a tensile strength of 14.22 kg mm–2 with 1.1% elongation, a compression strength of 42.61 kg mm–2, and an impact strength of 0.30 kgm cm–2. The properties are adequate for certain bearing applications, and the aluminium-mica composite bearings were found to run under boundary lubrication, semi-dry and dry friction conditions whereas the matrix alloy (without mica) bearings seized or showed stick slip under the same conditions.

New reagents 3: aluminium iodide - a highly regioselective ether-cleaving reagent with novel cleavage pattern

AlI3 is an easily accessible and versatile ether-cleaving reagent.

Seizure resistance of cast aluminium alleys containing dispersed graphite particles of differing sizes

The seizure resistance of cast graphite-aluminium composite alloys containing graphite particles of various sizes was studied using a Hohman wear tester. If the graphite content is more than 2% these alloys can be selfmated without seizure under conditions of boundary lubrication. The size and shape of the graphite particles had no significant effect on seizure resistance. Owing to the extensive deformation and fragmentation of graphite, the low yield strength of the aluminium matrix and the low flow stress of the graphite particles, a continuous layer of graphite is formed on the mating surfaces even after a short running-in period. This layer persisted even after extensive wear deformation.

Mechanism of improvement in oil spreadability of aluminium alloy-graphite particle composites

The spreadability of SAE-30 oil on Al-12 Si base (LM-13) alloy containing dispersed graphite particles about 50 μm average size in its matrix is found to be greater than on either LM-13 with no graphite or brass. It is also found that the spreadability on LM-13 base alloys increase with increasing volume of graphite dispersion in the matrix of these alloys. Further increases in the spreadability of oil on machined LM-13-graphite particle composite test surfaces occur if these are rubbed initially against control discs of either LM-13 or grey cast iron. The formation of a triboinduced graphite-rich layer, confirmed by esca, appears to be responsible for the improved oil spreadability on the rubbed test surfaces of LM-13 base alloys as compared to the as-machined test surfaces prior to rubbing. The triboinduced layer of graphite is apparently responsible for the observed reduction in the friction, wear and seizing tendency of triboelements made from aluminium alloy-graphite particle composites.

Efficacy of nano-silver in alleviating bacteria-related blockage in cut rose cv. Movie Star stems

Postharvest treatments with nano-silver (NS) significantly improve water relations and therefore prolong the vase life of several cut flowers, including rose (Rosa hybrida cv. Movie Star). The efficacy of NS in alleviating bacterial related blockage in the stem-ends of cut cv. Movie Star was further investigated. Four dominant bacteria strains Pseudomonas fluorescens, Aeromonas sp., Comamonas acidovorans and Chryseomonas luteola were isolated from the stem-ends of cut roses. High numbers of the isolated bacteria at 10 8colony forming unitsmL -1 vase solution led to a sharp reduction in vase life, flower fresh weight, and water uptake. In vitro assessments of the antibacterial activity of NS against the four bacterial strains was >80% at 5mgL -1 and nearly 100% at 50mgL -1. Bacterial blockage in the stem-ends of cut cv. Movie Star roses with and without NS pulse treatments was assessed during the vase period using scanning electron microscopy. Following a 50mgL -1 NS pulse treatment, there were few bacterial cells on the cut surface of the stems even on day 7. Moreover, no obvious bacterial blockage was observed inside the xylem vessels. In contrast, the cut surface of control stems was covered with bacteria and associated amorphous substances, and numerous bacteria were found in the xylem vessels. © 2012 Elsevier B.V.

The need for cost-effectiveness analyses of antimicrobial stewardship programmes: A structured review

The cost effectiveness of antimicrobial stewardship (AMS) programmes was reviewed in hospital settings of Organisation for Economic Co-operation and Development (OECD) countries, and limited to adult patient populations. In each of the 36 studies, the type of AMS strategy and the clinical and cost outcomes were evaluated. The main AMS strategy implemented was prospective audit with intervention and feedback (PAIF), followed by the use of rapid technology, including rapid polymerase chain reaction (PCR)-based methods and matrix-assisted laser desorption/ionisation time-of-flight (MALDI-TOF) technology, for the treatment of bloodstream infections. All but one of the 36 studies reported that AMS resulted in a reduction in pharmacy expenditure. Among 27 studies measuring changes to health outcomes, either no change was reported post-AMS, or the additional benefits achieved from these outcomes were not quantified. Only two studies performed a full economic evaluation: one on a PAIF-based AMS intervention; and the other on use of rapid technology for the selection of appropriate treatment for serious Staphylococcus aureus infections. Both studies found the interventions to be cost effective. AMS programmes achieved a reduction in pharmacy expenditure, but there was a lack of consistency in the reported cost outcomes making it difficult to compare between interventions. A failure to capture complete costs in terms of resource use makes it difficult to determine the true cost of these interventions. There is an urgent need for full economic evaluations that compare relative changes both in clinical and cost outcomes to enable identification of the most cost-effective AMS strategies in hospitals.

Effects of three different nano-silver formulations on cut Acacia holosericea vase life

The relative efficacies of three chemically different nano-silver (NS) formulations were evaluated for their potential to extend the vase life of short-lived cut Acacia holosericea foliage. The novel proprietary formulations were neutral NS, acidic NS and ionic NS. They were characterised in terms of particle size, pH value, colour and odour. The NS treatments were applied as vase (lower concentrations) or pulse (higher concentrations) solutions. Among the treatments compared, neutral NS as a 4 mg L-1 vase solution or as a 40 mg L-1 24 h pulse treatment and acidic NS as a 0.5 mg L-1 vase solution or as a 5 mg L-1 24 h pulse treatment significantly (P <= 0.05) extended the vase life of A. holosericea. Vase life extensions over the deionised water (DI) controls were associated with better maintenance of relative fresh weight and vase water uptake, suppression of bacterial growth in the vase water and stem-end, and delaying stem blockage. In contrast, ionic-NS applied as a 0.5 or 1 mg L-1 vase solution treatment or as a 5 or 10 mg L-1 pulse treatment caused severe phytotoxicity to cut A. holosericea stems. The results suggest that NS treatments, especially neutral NS and acidic NS pulse treatments, could be a potential postharvest technology for commercial application to cut A. holosericea. (C) 2011 Elsevier B.V. All rights reserved.

Thermal decomposition of hydrazinium aluminium sulfate hydrate and hydrazinate

As a part of our research programme on hydrazine derivatives [I-4]. we have prepared a number of hydrazinium metal sulfates [ 1.S] (N2 H5), M(SO4)2, where M = Mn, Fe, Co, Ni, Cu. Zn, Cd and Mg and their hydrazine adducts [2] of the type (N2H5)2M(SO4)2 . 3 N2H4. where M = Fe, Co and Ni, as well as N2H5AI(SO4)2 . 6N2H4. Recently, we reported [5.6] the thermal analysis of these compounds. Our .literature survey on the thermal analysis of alums [7] and aluminium salts [8] indicated that, although the preparation of hydrazinium aluminium sulfate dodecahydrate, N2H5Al(SO4)2 . 12 H2O, has been reported [9], there appears to be no report on its thermal analysis. Here, we report the results df the thermal analysis of N2H5Al(SO4)2 . 12 H2O and N2H5Al(SO4)2 . 2N2H4.