Radiation balance of the tropical ocean surface measured during Atlantic Expedition GARP 1974 (Table 1)

The net flux of all irreversible fluxes of radiation and heat crossing the ocean surface is determined for phase III of GATE at position no. 27 (WFS "Planet", FRG). The radiation fluxes have been measured directly, while the heat fluxes have been parameterized with the bulk formula however with bulk coefficients depending on stability. The heat loss of the ocean due to warming of the cooler precipitation is included for the determination of the net flux at the ocean surface. Some examples of hourly mean values of different fluxes during different weather conditions are additionally shown.

(Table 2) Age determination of sediment cores from the Portuguese Margin

We demonstrate that changes in the behavior of the Mediterranean Outflow Water (MOW) prior to and through the last deglaciation played an important role in promoting Meridional Overturning Circulation (MOC). Estimation of past MOW salt and heat fluxes indicates that they gradually increased through the last deglaciation. Between 17.5 and 14.6 thousand years ago (ka B.P., where B.P. references year 1950), net evaporation from the Mediterranean exported sufficient fresh water from the North Atlantic catchment to cause an average salinity increase of 0.5 psu throughout the upper 2000 m of the entire North Atlantic to the north of 25°N. Combined with rapid intensification and shoaling of the MOW plume, which we identify around 15-14.5 ka B.P., this deglacial MOW-related salt accumulation preconditioned the North Atlantic for abrupt resumption of the MOC at 14.6 ka B.P.

A influência de decisões arquitetônicas na eficiência energética do Campus vol. 1/UFRN

Building design is an effective way to achieve HVAC energy consumption reduction. However, this potentiality is often neglected by architects due to the lack of references to support design decisions. This works intends to propose architectural design guidelines for energy efficiency and thermal performance of Campus/UFRN buildings. These guidelines are based on computer simulations results using the software DesignBuilder. The definition of simulation models has begun with envelope variables, partially done after a field study of thirteen buildings at UFRN/Campus. This field study indicated some basic envelope patterns that were applied in simulation models. Occupation variables were identified with temperature and energy consumption monitoring procedures and a verification of illumination and equipment power, both developed at the Campus/UFRN administration building. Three simulation models were proposed according to different design phases and decisions. The first model represents early design decisions, simulating the combination of different types of geometry with three levels of envelope thermal performance. The second model, still as a part of early design phase, analyses thermal changes between circulation halls lateral and central and office rooms, as well as the heat fluxes and monthly temperatures in each circulation hall. The third model analyses the influence of middle-design and detail design decisions on energy consumption and thermal performance. In this model, different solutions of roofs, shading devices, walls and external colors were simulated. The results of all simulation models suggest a high influence of thermal loads due to the incidence of solar radiation on windows and surfaces, which highlights the importance of window shading devices, office room orientation and absorptance of roof and walls surfaces

Influence of the sea state on Mediterranean heavy precipitation: a case-study from HyMeX SOP1

Sea state can influence the turbulent air–sea exchanges, especially the momentum flux, by modifying the sea-surface roughness. The high-resolution non-hydrostatic convection-permitting model MESO-NH is used here to investigate the impact of a more realistic representation of the waves on heavy precipitation during the Intense Observation Period (IOP) 16a of the first HyMeX Special Observation Period (SOP1). Several quasi-stationary mesoscale convective systems developed over the western Mediterranean region, two of them over the sea, and resulted in heavy precipitation on the French and Italian coasts on 26 October 2012. Three different bulk parametrizations are tested in this study: a reference case (NOWAV) without any wave effect, a parametrization taking into account theoretical wave effects (WAV) and a last one with realistic wave characteristics from the MFWAM analyses (WAM). Using a realistic wave representation in WAM significantly increases the roughness length and the friction velocity with respect to NOWAV and WAV. The three MESO-NH sensitivity experiments of the IOP16a show that this surface-roughness increase in WAM generates higher momentum fluxes and directly impacts the low-level dynamics of the atmosphere, with a slowdown of the 10 m wind, when and where the wind speed exceeds 10 m s−1 and the sea state differs from the idealized one. The turbulent heat fluxes are not significantly influenced by the waves, these fluxes being controlled by the moisture content rather than by the wind speed in the simulations. Although the convective activity is globally well reproduced by all the simulations, the difference in the low-level dynamics of the atmosphere influences the localization of the simulated heavy precipitation. Objective evaluation of the daily rainfall amount and of the 10 m wind speed against the observations confirms the positive impact of the realistic wave representation on this simulation of heavy precipitation.

FLOW REGIME DRIVEN THERMAL ENHANCEMENT IN INTERNALLY-GROOVED TUBES

Internally-grooved refrigeration tubes maximize tube-side evaporative heat transfer rates and have been identified as a most promising technology for integration into compact cold plates. Unfortunately, the absence of phenomenological insights and physical models hinders the extrapolation of grooved-tube performance to new applications. The success of regime-based heat transfer correlations for smooth tubes has motivated the current effort to explore the relationship between flow regimes and enhanced heat transfer in internally-grooved tubes. In this thesis, a detailed analysis of smooth and internally-grooved tube data reveals that performance improvement in internally-grooved tubes at low-to-intermediate mass flux is a result of early flow regime transition. Based on this analysis, a new flow regime map and corresponding heat transfer coefficient correlation, which account for the increased wetted angle, turbulence, and Gregorig effects unique to internally-grooved tubes, were developed. A two-phase test facility was designed and fabricated to validate the newly-developed flow regime map and regime-based heat transfer coefficient correlation. As part of this setup, a non-intrusive optical technique was developed to study the dynamic nature of two-phase flows. It was found that different flow regimes result in unique temporally varying film thickness profiles. Using these profiles, quantitative flow regime identification measures were developed, including the ability to explain and quantify the more subtle transitions that exist between dominant flow regimes. Flow regime data, based on the newly-developed method, and heat transfer coefficient data, using infrared thermography, were collected for two-phase HFE-7100 flow in horizontal 2.62mm - 8.84mm diameter smooth and internally-grooved tubes with mass fluxes from 25-300 kg/m²s, heat fluxes from 4-56 kW/m², and vapor qualities approaching 1. In total, over 6500 combined data points for the adiabatic and diabatic smooth and internally-grooved tubes were acquired. Based on results from the experiments and a reinterpretation of data from independent researchers, it was established that heat transfer enhancement in internally-grooved tubes at low-to-intermediate mass flux is primarily due to early flow regime transition to Annular flow. The regime-based heat transfer coefficient outperformed empirical correlations from the literature, with mean and absolute deviations of 4.0% and 32% for the full range of data collected.

Intraseasonal variability of mixed layer depth in the tropical Indian Ocean

In this paper, we use an observational dataset built from Argo in situ profiles to describe the main large-scale patterns of intraseasonal mixed layer depth (MLD) variations in the Indian Ocean. An eddy permitting (0.25A degrees) regional ocean model that generally agrees well with those observed estimates is then used to investigate the mechanisms that drive MLD intraseasonal variations and to assess their potential impact on the related SST response. During summer, intraseasonal MLD variations in the Bay of Bengal and eastern equatorial Indian Ocean primarily respond to active/break convective phases of the summer monsoon. In the southern Arabian Sea, summer MLD variations are largely driven by seemingly-independent intraseasonal fluctuations of the Findlater jet intensity. During winter, the Madden-Julian Oscillation drives most of the intraseasonal MLD variability in the eastern equatorial Indian Ocean. Large winter MLD signals in northern Arabian Sea can, on the other hand, be related to advection of continental temperature anomalies from the northern end of the basin. In all the aforementioned regions, peak-to-peak MLD variations usually reach 10 m, but can exceed 20 m for the largest events. Buoyancy flux and wind stirring contribute to intraseasonal MLD fluctuations in roughly equal proportions, except for the Northern Arabian Sea in winter, where buoyancy fluxes dominate. A simple slab ocean analysis finally suggests that the impact of these MLD fluctuations on intraseasonal sea surface temperature variability is probably rather weak, because of the compensating effects of thermal capacity and sunlight penetration: a thin mixed-layer is more efficiently warmed at the surface by heat fluxes but loses more solar flux through its lower base.

A influência de decisões arquitetônicas na eficiência energética do Campus vol. 1/UFRN

Building design is an effective way to achieve HVAC energy consumption reduction. However, this potentiality is often neglected by architects due to the lack of references to support design decisions. This works intends to propose architectural design guidelines for energy efficiency and thermal performance of Campus/UFRN buildings. These guidelines are based on computer simulations results using the software DesignBuilder. The definition of simulation models has begun with envelope variables, partially done after a field study of thirteen buildings at UFRN/Campus. This field study indicated some basic envelope patterns that were applied in simulation models. Occupation variables were identified with temperature and energy consumption monitoring procedures and a verification of illumination and equipment power, both developed at the Campus/UFRN administration building. Three simulation models were proposed according to different design phases and decisions. The first model represents early design decisions, simulating the combination of different types of geometry with three levels of envelope thermal performance. The second model, still as a part of early design phase, analyses thermal changes between circulation halls lateral and central and office rooms, as well as the heat fluxes and monthly temperatures in each circulation hall. The third model analyses the influence of middle-design and detail design decisions on energy consumption and thermal performance. In this model, different solutions of roofs, shading devices, walls and external colors were simulated. The results of all simulation models suggest a high influence of thermal loads due to the incidence of solar radiation on windows and surfaces, which highlights the importance of window shading devices, office room orientation and absorptance of roof and walls surfaces

Échanges d’énergie et d’eau des écosystèmes nordiques dans un contexte de changement climatique

Le réchauffement climatique affecte fortement les régions nordiques du Canada où le dégel du pergélisol discontinu à sa limite sud est accompagné du mouvement de la limite des arbres vers le nord en zone de pergélisol continu. Ces altérations faites aux paysages de la Taïga des Plaines sont le point de départ de plusieurs rétroactions puisque les changements apportés aux caractéristiques de la surface (au niveau de l’albédo, l’humidité du sol et la rugosité de la surface) vont à leur tour entraîner des modifications biophysiques et éventuellement influencer l’augmentation ou la diminution subséquente des températures et de l’humidité de l’air. Seulement, il y a un nombre important de facteurs d’influence qu’il est difficile de projeter toutes les boucles rétroactives qui surviendront avec les présents changements climatiques en régions nordiques. Dans le but de caractériser les échanges d’eau et d’énergie entre la surface et l’atmosphère de trois sites des Territoires du Nord-Ouest subissant les conséquences de l’augmentation des températures de l’air, la méthode micro-météorologique de covariance des turbulences fut utilisée en 2013 aux sites de Scotty Creek (forêt boréale et tourbière nordique en zone de pergélisol sporadique-discontinu), de Havikpak Creek (forêt boréale nordique en zone de pergélisol continu) et de Trail Valley Creek (toundra arctique en zone de pergélisol continu). En identifiant les procédés biotiques et abiotiques (ex. intensité lumineuse, disponibilité en eau, etc.) d’évapotranspiration aux trois sites, les contrôles par l’eau et l’énergie furent caractérisés et permirent ainsi de projeter une augmentation de la limitation en eau, mais surtout en énergie du site de Trail Valley Creek. La répartition de l’énergie projetée est semblable à celle de Havikpak Creek, avec une augmentation de la proportion du flux de chaleur sensible au détriment de celui latent suite aux modifications des caractéristiques de la surface (albédo, rugosité et humidité du sol). L’augmentation relative du flux d’énergie sensible laisse présager une boucle rétroactive positive de l’augmentation des températures de l’air à ce site. Ensuite, en comparant des données modelées de la hauteur de la couche limite planétaire et des données provenant de profils atmosphériques d’Environnement Canada entre les trois sites, les changements de hauteur de cette couche atmosphérique furent aussi projetés. Trail Valley Creek pourrait connaître une hausse de la hauteur de sa couche limite planétaire avec le temps alors que Scotty Creek connaîtrait une diminution de celle-ci. Ces changements au niveau des couches atmosphériques liés à la répartition des flux d’énergie dans les écosystèmes se répercuteraient alors sur le climat régional de façon difficile à déterminer pour l’instant. Les changements apportés désignent une boucle rétroactive positive des températures de l’air à Trail Valley Creek et l’inverse à Scotty Creek. Les deux axes d’analyse arrivent donc aux mêmes conclusions et soulignent aussi l’importance de l’influence mutuelle entre le climat et les caractéristiques spécifiques des écosystèmes à la surface.

Échanges d’énergie et d’eau des écosystèmes nordiques dans un contexte de changement climatique

Le réchauffement climatique affecte fortement les régions nordiques du Canada où le dégel du pergélisol discontinu à sa limite sud est accompagné du mouvement de la limite des arbres vers le nord en zone de pergélisol continu. Ces altérations faites aux paysages de la Taïga des Plaines sont le point de départ de plusieurs rétroactions puisque les changements apportés aux caractéristiques de la surface (au niveau de l’albédo, l’humidité du sol et la rugosité de la surface) vont à leur tour entraîner des modifications biophysiques et éventuellement influencer l’augmentation ou la diminution subséquente des températures et de l’humidité de l’air. Seulement, il y a un nombre important de facteurs d’influence qu’il est difficile de projeter toutes les boucles rétroactives qui surviendront avec les présents changements climatiques en régions nordiques. Dans le but de caractériser les échanges d’eau et d’énergie entre la surface et l’atmosphère de trois sites des Territoires du Nord-Ouest subissant les conséquences de l’augmentation des températures de l’air, la méthode micro-météorologique de covariance des turbulences fut utilisée en 2013 aux sites de Scotty Creek (forêt boréale et tourbière nordique en zone de pergélisol sporadique-discontinu), de Havikpak Creek (forêt boréale nordique en zone de pergélisol continu) et de Trail Valley Creek (toundra arctique en zone de pergélisol continu). En identifiant les procédés biotiques et abiotiques (ex. intensité lumineuse, disponibilité en eau, etc.) d’évapotranspiration aux trois sites, les contrôles par l’eau et l’énergie furent caractérisés et permirent ainsi de projeter une augmentation de la limitation en eau, mais surtout en énergie du site de Trail Valley Creek. La répartition de l’énergie projetée est semblable à celle de Havikpak Creek, avec une augmentation de la proportion du flux de chaleur sensible au détriment de celui latent suite aux modifications des caractéristiques de la surface (albédo, rugosité et humidité du sol). L’augmentation relative du flux d’énergie sensible laisse présager une boucle rétroactive positive de l’augmentation des températures de l’air à ce site. Ensuite, en comparant des données modelées de la hauteur de la couche limite planétaire et des données provenant de profils atmosphériques d’Environnement Canada entre les trois sites, les changements de hauteur de cette couche atmosphérique furent aussi projetés. Trail Valley Creek pourrait connaître une hausse de la hauteur de sa couche limite planétaire avec le temps alors que Scotty Creek connaîtrait une diminution de celle-ci. Ces changements au niveau des couches atmosphériques liés à la répartition des flux d’énergie dans les écosystèmes se répercuteraient alors sur le climat régional de façon difficile à déterminer pour l’instant. Les changements apportés désignent une boucle rétroactive positive des températures de l’air à Trail Valley Creek et l’inverse à Scotty Creek. Les deux axes d’analyse arrivent donc aux mêmes conclusions et soulignent aussi l’importance de l’influence mutuelle entre le climat et les caractéristiques spécifiques des écosystèmes à la surface.

Experimentation of mitigation techniques to reduce the effects of permafrost degradation on transportation infrastructures at Beaver Creek experimental road site, Alaska Highway, Yukon

Les méthodes de design et de construction des routes développés dans le sud canadien ont maintenant besoin d’être adaptés aux environnements nordiques du pays afin de prévenir le dégel dramatique du pergélisol lors de la construction d’une nouvelle route. De plus, le réchauffement climatique occasionne présentement d’importants problèmes de stabilité des sols dans le nord canadien. Ces facteurs causent des pertes importantes au niveau des capacités fonctionnelles et structurales de l’Alaska Highway au Yukon sur un segment de plus de 200 km situé entre le village de Destruction Bay et la frontière de l’Alaska. Afin de trouver des solutions rentables à long terme, le ministère du transport du Yukon (en collaboration avec le Federal Highway Administration du gouvernement américain, Transports Canada, l’Université Laval, l’Université de Montréal et l’Alaska University transportation Center) a mis en place 12 sections d’essais de 50 mètres de longueur sur l’autoroute de l’Alaska près de Beaver Creek en 2008. Ces différentes sections d’essais ont été conçues pour évaluer une ou plusieurs méthodes combinées de stabilisation thermique telles que le drain thermique, le remblai à convection d’air, le pare-neige / pare-soleil, le remblai couvert de matières organiques, les drains longitudinaux, le déblaiement de la neige sur les pentes et la surface réfléchissante. Les objectifs spécifiques de la recherche sont 1) d’établir les régimes thermiques et les flux de chaleur dans chacune des sections pour les 3 premières années de fonctionnement ; 2) de documenter les facteurs pouvant favoriser ou nuire à l’efficacité des systèmes de protection et ; 3) de déterminer le rapport coûts/bénéfices à long terme pour chacune des techniques utilisées. Pour ce faire, une nouvelle méthode d’analyse, basée sur la mesure de flux d’extraction de chaleur Hx et d’induction Hi à l’interface entre le remblai et le sol naturel, a été utilisée dans cette étude. Certaines techniques de protection du pergélisol démontrent un bon potentiel durant leurs 3 premières années de fonctionnement. C’est le cas pour le remblai à convection d’air non-couvert, le remblai à convection d’air pleine largeur, les drains longitudinaux, le pare-soleil / pare-neige et la surface réfléchissante. Malheureusement, des problèmes dans l’installation des drains thermiques ont empêché une évaluation complète de leur efficacité.

Lake–atmosphere interactions at Alqueva reservoir: a case study in the summer of 2014

The study of lake–atmosphere interactions was the main purpose of a 2014 summer experiment at Alqueva reservoir in Portugal. Near-surface fluxes of momentum, heat and mass [water vapour (H2O) and carbon dioxide (CO2)] were obtained with the new Campbell Scientific’s IRGASON Integrated Open-Path CO2/H2O Gas Analyser and 3D Sonic Anemometer between 2 June and 2 October. On average, the reservoir was releasing energy in the form of sensible and latent heat flux during the study period. At the end of the 75 d, the total evaporation was estimated as 490.26 mm. A high correlation was found between the latent heat flux and the wind speed (R = 0.97). The temperature gradient between air and water was positive between 12 and 21 UTC, causing a negative sensible heat flux, and negative during the rest of the day, triggering a positive sensible heat flux. The reservoir acted as a sink of atmospheric CO2 with an average rate of −0.026 mg m−2 s−1. However, at a daily scale we found an unexpected uptake between 0 and 9 UTC and almost null flux between 13 and 19 UTC. Potential reasons for this result are further discussed. The net radiation was recorded for the same period and water column heat storage was estimated using water temperature profiles. The energy balance closure for the analysed period was 81%. In-water solar spectral downwelling irradiance profiles were measured with a new device allowing measurements independent of the solar zenith angle, which enabled the computation of the attenuation coefficient of light in the water column. The average attenuation coefficient for the photosynthetically active radiation spectral region varied from 0.849 ± 0.025 m−1 on 30 July to 1.459 ± 0.007 m−1 on 25 September.

Monitoring and simulation of water, heat,and CO2 fluxes in terrestrial ecosystems based on the APEIS-FLUX system

The Integrated Environmental Monitoring (IEM) project, part of the Asia-Pacific Environmental Innovation Strategy (APEIS) project, developed an integrated environmental monitoring system that can be used to detect, monitor, and assess environmental disasters, degradation, and their impacts in the Asia-Pacific region. The system primarily employs data from the moderate resolution imaging spectrometer (MODIS) sensor on the Earth Observation System- (EOS-) Terra/Aqua satellite,as well as those from ground observations at five sites in different ecological systems in China. From the preliminary data analysis on both annual and daily variations of water, heat and CO2 fluxes, we can confirm that this system basically has been working well. The results show that both latent flux and CO2 flux are much greater in the crop field than those in the grassland and the saline desert, whereas the sensible heat flux shows the opposite trend. Different data products from MODIS have very different correspondence, e.g. MODIS-derived land surface temperature has a close correlation with measured ones, but LAI and NPP are quite different from ground measurements, which suggests that the algorithms used to process MODIS data need to be revised by using the local dataset. We are now using the APEIS-FLUX data to develop an integrated model, which can simulate the regional water,heat, and carbon fluxes. Finally, we are expected to use this model to develop more precise high-order MODIS products in Asia-Pacific region.

Simulated and observed fluxes of sensible and latent heat and CO2 at the WLEF-TV tower using SiB2.5

Three years of meteorological data collected at the WLEF-TV tower were used to drive a revised version of the Simple Biosphere (SiB 2.5) Model. Physiological properties and vegetation phenology were specified from satellite imagery. Simulated fluxes of heat, moisture, and carbon were compared to eddy covariance measurements taken onsite as a means of evaluating model performance on diurnal, synoptic, seasonal, and interannual time scales. The model was very successful in simulating variations of latent heat flux when compared to observations, slightly less so in the simulation of sensible heat flux. The model overestimated peak values of sensible heat flux on both monthly and diurnal scales. There was evidence that the differences between observed and simulated fluxes might be linked to wetlands near the WLEF tower, which were not present in the SiB simulation. The model overestimated the magnitude of the net ecosystem exchange of CO2 in both summer and winter. Mid-day maximum assimilation was well represented by the model, but late afternoon simulations showed excessive carbon uptake due to misrepresentation of within-canopy shading in the model. Interannual variability was not well simulated because only a single year of satellite imagery was used to parameterize the model.