Potentialities of two solventless extraction approaches—Stir bar sorptive extraction and headspace solid-phase microextraction for determination of higher alcohol acetates, isoamyl esters and ethyl esters in wines

A stir bar sorptive extraction with liquid desorption followed by large volume injection coupled to gas chromatography–quadrupole mass spectrometry (SBSE-LD/LVI-GC–qMS) was evaluated for the simultaneous determination of higher alcohol acetates (HAA), isoamyl esters (IsoE) and ethyl esters (EE) of fatty acids. The method performance was assessed and compared with other solventless technique, the solid-phase microextraction (SPME) in headspace mode (HS). For both techniques, influential experimental parameters were optimised to provide sensitive and robust methods. The SBSE-LD/LVI methodology was previously optimised in terms of extraction time, influence of ethanol in the matrix, liquid desorption (LD) conditions and instrumental settings. Higher extraction efficiency was obtained using 60 min of extraction time, 10% ethanol content, n-pentane as desorption solvent, 15 min for the back-extraction period, 10 mL min−1 for the solvent vent flow rate and 10 °C for the inlet temperature. For HS-SPME, the fibre coated with 50/30 μm divinylbenzene/carboxen/polydimethylsiloxane (DVB/CAR/PDMS) afforded highest extraction efficiency, providing the best sensitivity for the target volatiles, particularly when the samples were extracted at 25 °C for 60 min under continuous stirring in the presence of sodium chloride (10% (w/v)). Both methodologies showed good linearity over the concentration range tested, with correlation coefficients higher than 0.984 for HS-SPME and 0.982 for SBES-LD approach, for all analytes. A good reproducibility was attained and low detection limits were achieved using both SBSE-LD (0.03–28.96 μg L−1) and HS-SPME (0.02–20.29 μg L−1) methodologies. The quantification limits for SBSE-LD approach ranging from 0.11 to 96.56 μg L−and from 0.06 to 67.63 μg L−1 for HS-SPME. Using the HS-SPME approach an average recovery of about 70% was obtained whilst by using SBSE-LD obtained average recovery were close to 80%. The analytical and procedural advantages and disadvantages of these two methods have been compared. Both analytical methods were used to determine the HAA, IsoE and EE fatty acids content in “Terras Madeirenses” table wines. A total of 16 esters were identified and quantified from the wine extracts by HS-SPME whereas by SBSE-LD technique were found 25 esters which include 2 higher alcohol acetates, 4 isoamyl esters and 19 ethyl esters of fatty acids. Generally SBSE-LD provided higher sensitivity with decreased analysis time.

New bacterial cellulose nanocomposites prepared by in situ radical polymerization of methacrylate monomers

Bacterial cellulose/polymethacrylate nanocomposites have received attention in numerous areas of study and in a variety of applications. The attractive properties of methacrylate polymers and bacterial cellulose, BC, allow the synthesis of new nanocomposites with distinct characteristics. In this study, BC/poly(glycidylmethacrylate) (BC/PGMA) and BC/poly(ethyleneglycol)methacrylate (BC/PPEGMA) nanocomposites were prepared through in situ free radical polymerization of GMA and PEGMA, respectively. Ammonium persulphate (APS) was used as an initiator and N,N’methylenebisacrilamide (MBA) was used as a crosslinker in BC/PGMA. Chemical composition, morphology, thermal stability, water absorption, mechanic and surface properties were determined through specific characterization techniques. The optimal polymerization was obtained at (1:2) for BC/PGMA, (1:2:0.2) ratio for BC/GMA/MBA and (1:20) for BC/PPEGMA, with 0.5% of initiator at 60 ºC during 6 h. A maximum of 67% and 87% of incorporation percentage was obtained, respectively, for the nanocomposites BC/PGMA/MBA and BC/PPEGMA. BC/PGMA nanocomposites exhibited an increase of roughness and compactation of the three-dimensional structure, an improvement in the thermal and mechanical properties, and a decrease in their swelling ability and crystallinity. On the other hand, BC/PPEGMA showed a decrease of stiffness of three-dimensional structure, improvement in thermal and mechanical properties, an increase in their swelling ability and a decrease the crystallinity. Both BC/polymethacrylate nanocomposites exhibited a basic surface character. The acid treatment showed to be a suitable strategy to modifiy BC/PGMA nanocomposites through epoxide ring-opening reaction mechanism. Nanocomposites became more compact, smooth and with more water retention ability. A decrease in the thermal and mechanical proprieties was observed. The new nanocomposites acquired properties useful to biomedical applications or/and removal of heavy metals due to the presence of functional groups.

Development of a new analytical approach based on cellulose membrane and chelator for differentiation of labile and inert metal species in aquatic systems

A new procedure was developed in this study, based on a system equipped with a cellulose membrane and a tetraethylenepentamine hexaacetate chelator (MD-TEPHA) for in situ characterization of the lability of metal species in aquatic systems. To this end, the DM-TEPHA system was prepared by adding TEPHA chelator to cellulose bags pre-purified with 1.0 mol L-1 of HCl and NaOH solutions. After the MD-TEPHA system was sealed, it was examined in the laboratory to evaluate the influence of complexation time (0-24 h), pH (3.0, 4.0, 5.0, 6.0 and 7.0), metal ions (Cu, Cd, Fe, Mn and Ni) and concentration of organic matter (15, 30 and 60 mg L-1) on the relative lability of metal species by TEPHA chelator. The results showed that Fe and Cu metals were complexed more slowly by TEPHA chelator in the MD-TEPHA system than were Cd, Ni and Mn in all pH used. It was also found that the pH strongly influences the process of metal complexation by the MD-TEPHA system. At all the pH levels, Cd, Mn and Ni showed greater complexation with TEPHA chelator (recovery of about 95-75%) than did Cu and Fe metals. Time also affects the lability of metal species complexed by aquatic humic substances (AHS); while Cd, Ni and Mn showed a faster kinetics, reaching equilibrium after about 100 min, and Cu and Fe approached equilibrium after 400 min. Increasing the AHS concentration decreases the lability of metal species by shifting the equilibrium to AHS-metal complexes. Our results indicate that the system under study offers an interesting alternative that can be applied to in situ experiments for differentiation of labile and inert metal species in aquatic systems. (c) 2006 Elsevier B.V. All rights reserved.

Evaluation of the genotoxicity of cellulose nanofibers

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of the synthetic coumarin, ethyl 2-oxo-2H-chromene-3-carboxylate, on activity of Crotalus durissus ruruima sPLA2 as well as on edema and platelet aggregation induced by this factor

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação da sensibilidade de diversas espécies de plantas daninhas aquáticas ao carfentrazone-ethyl, em ambiente controlado

Plantas aquáticas, especialmente macrófitas, tornam-se sério problema em hidrelétricas, afetando a múltipla utilização dos corpos d'água, incluindo produção de peixes e atividades de pesca, perdas d'água por evapotranspiração, esportes aquáticos, canoagem, irrigação e produção de energia nas usinas hidrelétricas. Com o objetivo de analisar o potencial de uso do carfentrazone-ethyl no controle das principais plantas daninhas aquáticas no Brasil, foi instalado um experimento em vasos com água. Utilizaram-se os seguintes tratamentos herbicidas (g i.a. ha-1): carfentrazone-ethyl a 15, 30 e 60; glyphosate a 4.536; 2,4-D a 4.690; imazapyr a 1.250; e uma testemunha sem herbicida. Esses tratamentos foram testados nas seguintes espécies: Eichhornia crassipes, Salvinia auriculata, Pistia stratiotes, Myriophyllum aquaticum, Brachiaria arrecta, Hydrocotyle umbellata, Typha sp. e Echinochloa polystachya. As avaliações foram efetuadas aos 7, 14, 21 e 28 dias após os tratamentos. Os resultados mostraram que o carfentrazone-ethyl foi eficiente no controle de E. crassipes (maior dose) e P. stratiotes (duas maiores doses), com efeito supressivo sobre S. auriculata. Foi observado que nas outras plantas daninhas estudadas não houve eficiência de controle.

Efeitos da dessecação com glyphosate e chlorimuron-ethyl na comunidade infestante e na produtividade da soja

O efeito de dessecantes sobre o período anterior à interferência (PAI) pode auxiliar na tomada de decisão para o manejo das plantas daninhas. O objetivo desta pesquisa foi verificar se a adição de chlorimuron-ethyl ao glyphosate, para dessecação em pré-semeadura, altera a extensão do PAI na soja. O experimento foi realizado em Jaboticabal-SP, Brasil, submetendo-se o cultivar Monsoy 7908RR a oito períodos de convivência com plantas daninhas, além de testemunhas no mato e no limpo, nos quais foram aplicados dois grupos de tratamentos: glyphosate e glyphosate + chlorimuron-ethyl. em cada período, foram calculados o índice de importância relativa e os índices de diversidade e equitabilidade; por meio da análise de regressão dos dados de produtividade de grãos, determinou-se o PAI. Digitaria insularis, Acanthospermum hispidum, Raphanus raphanistrum e Commelina benghalensis apresentaram maior importância relativa. Os índices de diversidade e equitabilidade oscilaram durante os períodos, e a diferença entre as plantas daninhas fundamentou-se no acúmulo de massa seca. O PAI na soja no tratamento com glyphosate foi de 37 dias após a semeadura (DAS) e de 51 DAS naquele com glyphosate + chlorimuron-ethyl. A adição de chlorimuron-ethyl ao glyphosate permite que a cultura conviva mais tempo com as plantas daninhas sem que ocorra redução significativa na produtividade.

Effects of ethyl-cyanoacrylate and octyl-cyanoacrylate on experimental corneal lesions in rabbits

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Selectivity of the plant growth regulators trinexapac-ethyl and sulfometuron-methyl to cultivated species

The aerial spraying of plant ripeners on sugar cane (Saccharum officinarum L.) crops causes often the contamination of neighboring areas, which subsidizes formal complaints from the neighbors. These contaminations are due to spraying taking place during inadequate environmental conditions or from technical mistakes during the application. One of the most important causes of this contamination is the susceptibility of the species being cultivated surrounding sugar cane. In order to evaluate the effects of sugar cane plant ripeners trinexapac-ethyl and sulfometuron-methyl on peanuts, cotton, potato, coffee, citrus, beans, sunflower, cassava, rubber, soybean, and grapes, eleven experiments - one for each species - were carried out from May 2009 to Jan. 2010. The field experiment was set according to a completely random design with five treatments and four replications. Just before or during flowering, a single treatment of trinexapac-ethyl at 100 or 200 g ha-1 and sulfometuron-methyl at 7.5 or 15 g ha-1 was applied to plants. A control treatment (plants not treated) for each species was part of each experiment. Trinexapac, at the doses of 100 and 200 g ha-1, showed selectivity to peanuts, cotton, potato, coffee, citrus, sunflower, cassava, rubber, soybean, and grape. At the lowest dose (100 g ha-1), it was selective for bean. Sulfometuron, at the dose of 7.5 g ha-1, was selective for peanuts and, at the two studied doses (7.5 and 15 g ha-1), it was selective for coffee, citrus, cassava, and rubber.

Enhancement of thermal stability, strength and extensibility of lipid-based polyurethanes with cellulose-based nanofibers

Cellulose was extracted from lignocellulosic fibers and nanocrystalline cellulose (NC) prepared by alkali treatment of the fiber, steam explosion of the mercerized fiber, bleaching of the steam exploded fiber and finally acid treatment by 5% oxalic acid followed again by steam explosion. The average length and diameter of the NC were between 200-250 nm and 4-5 nm, respectively, in a monodisperse distribution. Different concentrations of the NC (0.1, 0.5, 1.0, 1.5, 2.0 and 2.5% by weight) were dispersed non-covalently into a completely bio-based thermoplastic polyurethane (TPU) derived entirely from oleic acid. The physical properties of the TPU nanocomposites were assessed by Fourier Transform Infra-Red spectroscopy (FTIR), Thermo-Gravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC), X-Ray Diffraction (XRD), Dynamic Mechanical Analysis (DMA) and Mechanical Properties Analysis. The nanocomposites demonstrated enhanced stress and elongation at break and improved thermal stability compared to the neat TPU. The best results were obtained with 0.5% of NC in the TPU. The elongation at break of this sample was improved from 178% to 269% and its stress at break from 29.3 to 40.5 MPa. In this and all other samples the glass transition temperature, melting temperature and crystallization behavior were essentially unaffected. This finding suggests a potential method of increasing the strength and the elongation at break of typically brittle and weak lipid-based TPUs without alteration of the other physico-chemical properties of the polymer. (C) 2012 Elsevier Ltd. All rights reserved.

Cellulose nanocomposites with nanofibres isolated from pineapple leaf fibers for medical applications

Nanocellulose is the crystalline domains obtained from renewable cellulosic sources, used to increase mechanical properties and biodegrability in polymer composites. This work has been to study how high pressure defibrillation and chemical purification affect the PALF fibre morphology from micro to nanoscale. Microscopy techniques and X-ray diffraction were used to study the structure and properties of the prepared nanofibers and composites. Microscopy studies showed that the used individualization processes lead to a unique morphology of interconnected web-like structure of PALF fibers. The produced nanofibers were bundles of cellulose fibers of widths ranging between 5 and 15 nm and estimated lengths of several micrometers. Percentage yield and aspect ratio of the nanofiber obtained by this technique is found to be very high in comparison with other conventional methods. The nanocomposites were prepared by means of compression moulding, by stacking the nanocellulose fibre mats between polyurethane films. The results showed that the nanofibrils reinforced the polyurethane efficiently. The addition of 5 wt% of cellulose nanofibrils to PU increased the strength nearly 300% and the stiffness by 2600%. The developed composites were utilized to fabricate various versatile medical implants. (C) 2011 Elsevier Ltd. All rights reserved.

Efeito do trinexapac-ethyl na anatomia foliar de quatro espécies de grama

Os reguladores de crescimento podem retardar o desenvolvimento vegetativo das plantas de gramas e, assim, reduzir a frequência de cortes; contudo, existem poucas informações referentes aos efeitos desses produtos sobre as estruturas da anatomia foliar. Dessa forma, o presente trabalho teve por objetivo avaliar os efeitos da aplicação sequencial de duas doses de trinexapac-ethyl sobre a anatomia foliar das espécies de gramas São Carlos (Axonopus compressus), Batatais (Paspalum notatum), Santo Agostinho (Stenotaphrum secundatum) e Esmeralda (Zoysia japonica). Os tratamentos utilizados foram constituídos de duas aplicações sequenciais de trinexapac-ethyl nas doses de 56,5+56,5 e 113,0+113,0 g ha-1; além de uma testemunha sem aplicação, para cada espécie avaliada. Os gramados foram cortados à altura de 3 cm, com auxílio de um aparador de grama motorizado, e, em seguida, foram realizadas as aplicações dos tratamentos. Após 20 dias da primeira aplicação de trinexapac-ethyl, as parcelas foram novamente aparadas à altura de 3 cm e foi realizada a segunda aplicação dos tratamentos. O delineamento experimental utilizado foi o de blocos ao acaso, com quatro repetições. Aos 70 dias após a segunda aplicação dos tratamentos, foram realizadas as amostragens do material foliar, para as quatro espécies estudadas. Os dados das variáveis quantitativas foram submetidos ao teste estatístico multivariado de análise de componentes principais. Os resultados evidenciaram a formação de três e dois grupos principais, para os caracteres da região da quilha (nervura mediana) e da região da asa (situada entre a nervura mediana e a margem do limbo foliar), respectivamente. de modo geral, em cada formação dos agrupamentos, os tratamentos com trinexapac-ethyl apresentaram maior similaridade entre si, em relação às respectivas testemunhas. Conclui-se que a aplicação sequencial de trinexapac-ethyl alterou algumas estruturas anatômicas da região da quilha e da asa do limbo foliar das espécies de gramas estudadas.

Use of Saponins as an Effective Surface Modifier in Cellulose Nanocomposites

The present paper deals with the extraction of saponins from the pericarp of Sapindus mukorossi to use as compatibilizer in nanocomposites. The nanofibrils extracted from banana fibres are utilized as reinforcement of nanocomposite. These nanofibers were treated with Saponin, GPS (3-Glycidoxypropyltrimethoxysilane) and APS (3-Aminopropyltriethoxysilane) to compare the effectiveness of surface treatment. The effectiveness of surface modification was reflected on the increase in mechanical (tensile test, flexural modulus, impact test) properties and decrease in the RMS (Roughness Measurement System) roughness investigation by SFM (Scanning force microscopy) analysis.

Cellulose-Based Bio- and Nanocomposites: A Review

Cellulose macro- and nanofibers have gained increasing attention due to the high strength and stiffness, biodegradability and renewability, and their production and application in development of composites. Application of cellulose nanofibers for the development of composites is a relatively new research area. Cellulose macro- and nanofibers can be used as reinforcement in composite materials because of enhanced mechanical, thermal, and biodegradation properties of composites. Cellulose fibers are hydrophilic in nature, so it becomes necessary to increase their surface roughness for the development of composites with enhanced properties. In the present paper, we have reviewed the surface modification of cellulose fibers by various methods. Processing methods, properties, and various applications of nanocellulose and cellulosic composites are also discussed in this paper.

Ionizing radiation induced degradation of poly (2-methoxy-5-(2 '-ethyl-hexyloxy)-1,4-phenylene vinylene) in solution

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)