Oxidative Leaching of metals from electronic waste with solutions based on quaternary ammonium salts

The treatment of electric and electronic waste (WEEE) is a problem which receives ever more attention. An inadequate treatment results in harmful products ending up in the environment. This project intends to investigate the possibilities of an alternative route for recycling of metals from printed circuit boards (PCBs) obtained from rejected computers. The process is based on aqueous solutions composed of an etchant, either 0.2 M CuCl2.2H2O or 0.2 M FeCl3.6H2O, and a quaternary ammonium salt (quat) such as choline chloride or chlormequat. These solutions are reminiscent of deep eutectic solvents (DES) based on quats. DES are quite similar to ionic liquids (ILs) and are used as well as alternative solvents with a great diversity of physical properties, making them attractive for replacement of hazardous, volatile solvents (e.g. VOCs). A remarkable difference between genuine DES and ILs with the solutions used in this project is the addition of rather large quantities of water. It is shown the presence of water has a lot of advantages on the leaching of metals, while the properties typical for DES still remain. The oxidizing capacities of Cu(II) stem from the existence of a stable Cu(I) component in quat based DES and thus the leaching stems from the activity of the Cu(II)/Cu(I) redox couple. The advantage of Fe(III) in combination with DES is the fact that the Fe(III)/Fe(II) redox couple becomes reversible, which is not true in pure water. This opens perspectives for regeneration of the etching solution. In this project the leaching of copper was studied as a function of gradual increasing water content from 0 - 100w% with the same concentration of copper chloride or iron(III) chloride at room temperature and 80ºC. The solutions were also tested on real PCBs. At room temperature a maximum leaching effect for copper was obtained with 30w% choline chloride with 0.2 M CuCl2.2H2O. The leaching effect is still stronger at 80°C, b ut of course these solutions are more energy consuming. For aluminium, tin, zinc and lead, the leaching was faster at 80ºC. Iron and nickel dissolved easily at room temperature. The solutions were not able to dissolve gold, silver, rhodium and platinum.

Iterative refinement approach for QOS-Aware service configuration

In heterogeneous environments, diversity of resources among the devices may affect their ability to perform services with specific QoS constraints, and drive peers to group themselves in a coalition for cooperative service execution. The dynamic selection of peers should be influenced by user’s QoS requirements as well as local computation availability, tailoring provided service to user’s specific needs. However, complex dynamic real-time scenarios may prevent the possibility of computing optimal service configurations before execution. An iterative refinement approach with the ability to trade off deliberation time for the quality of the solution is proposed. We state the importance of quickly finding a good initial solution and propose heuristic evaluation functions that optimise the rate at which the quality of the current solution improves as the algorithms have more time to run.

Time-bounded distributed QoS-aware service configuration in heterogeneous cooperative environments

The scarcity and diversity of resources among the devices of heterogeneous computing environments may affect their ability to perform services with specific Quality of Service constraints, particularly in dynamic distributed environments where the characteristics of the computational load cannot always be predicted in advance. Our work addresses this problem by allowing resource constrained devices to cooperate with more powerful neighbour nodes, opportunistically taking advantage of global distributed resources and processing power. Rather than assuming that the dynamic configuration of this cooperative service executes until it computes its optimal output, the paper proposes an anytime approach that has the ability to tradeoff deliberation time for the quality of the solution. Extensive simulations demonstrate that the proposed anytime algorithms are able to quickly find a good initial solution and effectively optimise the rate at which the quality of the current solution improves at each iteration, with an overhead that can be considered negligible.

Inherently chiral calix[4]arenes with planar chirality: two new entries to the family

The synthesis of two new inherently chiral calix[4]arenes (ICCs, 1 and 2), endowed with electron-rich concave surfaces, has been achieved through the desymmetrization of a lower rim distal-bridged oxacyclophane (OCP) macrocycle. The new highly emissive ICCs were resolved by chiral HPLC, and the enantiomeric nature of the isolated antipodes proved by electronic circular dichroism (CD). Using time-dependent density functional calculations of CD spectra, their absolute configurations were established. NMR studies with (S)-Pirkle's alcohol unequivocally showed that the host-guest interactions occur in the chiral pocket comprehending the calix-OCP exo cavities and the carbazole moieties.

Role of abrasive material on micro-abrasion wear tests

Micro-abrasion wear tests with ball-cratering configuration are widely used. Sources of variability are already studied by different authors and conditions for testing are parameterized by BS EN 1071-6: 2007 standard which refers silicon carbide as abrasive. However, the use of other abrasives is possible and allowed. In this work, ball-cratering wear tests were performed using four different abrasive particles of three dissimilar materials: diamond, alumina and silicon carbide. Tests were carried out under the same conditions on a steel plate provided with TiB2 hard coating. For each abrasive, five different test durations were used allowing understanding the initial wear phenomena. Composition and shape of abrasive particles were investigated by SEM and EDS. Scar areas were observed by optical and electronic microscopy in order to understand the wear effects caused by each of them. Scar geometry and grooves were analyzed and compared. Wear coefficient was calculated for each situation. It was observed that diamond particles produce well-defined and circular wear scars. Different silicon carbide particles presented dissimilar results as consequence of distinct particle shape and size distribution.

WeSenseNET - Plataforma de Visualização, Gestão Remota e Agregação Múltipla de Dados

Nos últimos anos, o avanço da tecnologia e a miniaturização de diversos componentes de electrónica associados a novos conceitos têm permitido nascer novas ideias e projectos, que até há alguns anos não passariam de ficção científica. Talvez o exemplo mais acabado seja actualmente o smartphone, um pequeno bloco de hardware e software, com capacidade de processamento que ultrapassa várias vezes o dos computadores com uma dúzia de anos. Estas capacidades têm sido utilizadas em comunicações, blocos de notas, agendas e até entretenimento. No entanto, podem ser reutilizadas para ajudar a resolver algumas limitações/constrangimentos da actualidade. Dentro destes destacam-se a gestão de recursos escassos. Com efeito, o consumo de energia eléctrica tem aumentado como consequência directa do desenvolvimento global e aumento do número de aparelhos eléctricos. Uma percentagem significativa de energia eléctrica tem sido produzida através de recursos não-renováveis de energia. No entanto, a dependência energética, associada à subida de preços e a redução das emissões de gases do efeito estufa, estimula o desenvolvimento de novas soluções que permitam lidar com esta situação. O desempenho energético por sua vez depende não só das características da estrutura, mas também do comportamento do utilizador. O desempenho energético dos edifícios é muito importante, uma vez que os respectivos consumos são responsáveis por mais de metade do total da energia produzida. Desta forma, a fim de alcançar um melhor desempenho é importante não só considerar o desempenho de estrutura, mas também monitorizar o comportamento do utilizador. Esta última questão coloca várias limitações, uma vez que depende muito do tipo de utilizador. Um dos conceitos actuais emergentes são as chamadas redes de sensores sem fio. Com esta tecnologia, pequenos módulos podem ser desenvolvidos com muitas possibilidades de conectividade, com elevado poder de processamento e com grande autonomia, sem serem excessivamente caros. Isto proporciona os meios para implementar vários dispositivos em toda a instalação, para recolher uma variedade de dados, sendo posteriormente armazenados num servidor. Os blocos fundamentais da infra-estrutura de sensores do projecto foram concebidos na Evoleo Technologies em simultâneo com o decorrer do estágio. Estes blocos recolhem dados específicos na instalação, e periodicamente enviam para o servidor central os valores recolhidos, onde são armazenados e colocados à disposição do utilizador. Os dados recolhidos podem então ser apresentados ao utilizador, proporcionando um registo de consumo de energia associado a um dado período de tempo. Uma vez que todos os dados são armazenados no servidor, podem ser efectuados estudos para determinar o uso típico, possíveis problemas em aparelhos, a qualidade da energia eléctrica, etc., permitindo determinar onde a energia está a ser eventualmente desperdiçada e fornecendo dados ao utilizador para que este possa proceder a alterações, tendo por base dados recolhidos num dado período. O objectivo principal deste trabalho passa por estabelecer a ligação entre o nível máquina e o nível de utilizador, isto é, uma plataforma de interacção entre dispositivos e administrador da instalação. Fornecer os dados de uma forma fácil e sem necessidade de instalação de software específico em cada dispositivo que se pretenda utilizar para monitorizar foi uma das principais preocupações das fases de concepção do projecto.

Environmental/Regatta Buoy: Telemetry and Configuration

A monitorização ambiental é essencial para a tomada de decisões tanto na ciência como na indústria. Em particular, uma vez que a água é essencial à vida e a superfície da Terra é composta principalmente por água, a monitorização do clima e dos parâmetros relacionados com a água em ecossistemas sensíveis, tais como oceanos, lagoas, rios e lagos, é de extrema importância. Um dos métodos mais comuns para monitorar a água é implantar bóias. O presente trabalho está integrado num projeto mais amplo, com o objetivo de projectar e desenvolver uma bóia autónoma para a investigação científica com dois modos de funcionamento: (i) monitorização ambiental ; e (ii) baliza ativa de regata. Assim, a bóia tem duas aplicações principais: a coleta e armazenamento de dados e a assistência a regatas de veleiros autónomos. O projeto arrancou há dois anos com um grupo de quatro estudantes internacionais. Eles projetaram e construíram a estrutura física, compraram e montaram o sistema de ancoragem da bóia e escolherem a maioria dos componentes electrónicos para o sistema geral de controlo e medição. Este ano, durante o primeiro semestre, dois estudantes belgas - Jeroen Vervenne e Hendrick Verschelde – trabalharam nos subsistemas de recolha e armazenamento de dados (unidade de controlo escrava) e de telemetria e configuração (unidade de controlo mestre) assim como definiram o protocolo de comunicação da aplicação. O trabalho desta tese continua o desenvolvimento do subsistema de telemetria e configuração. Este subsistema _e responsável pela configuração do modo de funcionamento e dos sensores assim como pela comunicação com a estacão de base (controlo ambiental), barcos (baliza ativa de regata) e com o subsistema de recolha e armazenamento de dados. O desenvolvimento do subsistema de recolha e armazenamento de dados, que coleta e armazena num cartão SD os dados dos sensores selecionados, prossegue com outro estudante belga - Mathias van Flieberge. O objetivo desta tese é, por um lado, implementar o subsistema de telemetria e de configuração na unidade de controle mestre e, por outro lado, refinar e implementar, conjuntamente com Mathias van Flieberge, o protocolo de nível de aplicação projetado. Em particular, a unidade de controlo mestre deve processar e atribuir prioridades às mensagens recebidas da estacão base, solicitar dados à unidade de controlo escrava e difundir mensagens com informação de posição e condições de vento e água no modo de regata. Enquanto que a comunicação entre a unidade de controlo mestre e a estacão base e a unidade de controlo mestre e os barcos é sem fios, a unidade de controlo mestre e a unidade de controlo escrava comunicam através de uma ligação série. A bóia tem atualmente duas limitações: (i) a carga máxima é de 40 kg; e (ii) apenas pode ser utilizada em rios ou próximo da costa dada à limitação de distância imposta pela técnica de comunicação sem fios escolhida.

Infra-estrutura de software baseada em standards de apoio à eficiência energética utilizando fontes de energia renovável

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para a obtenção do grau de Mestre em Engenharia Electrotécnica e de Computadores

TEA: Timing and Energy Aware compression architecture for Efficient Configuration in CGRAs

Coarse Grained Reconfigurable Architectures (CGRAs) are emerging as enabling platforms to meet the high performance demanded by modern applications (e.g. 4G, CDMA, etc.). Recently proposed CGRAs offer time-multiplexing and dynamic applications parallelism to enhance device utilization and reduce energy consumption at the cost of additional memory (up to 50% area of the overall platform). To reduce the memory overheads, novel CGRAs employ either statistical compression, intermediate compact representation, or multicasting. Each compaction technique has different properties (i.e. compression ratio, decompression time and decompression energy) and is best suited for a particular class of applications. However, existing research only deals with these methods separately. Moreover, they only analyze the compaction ratio and do not evaluate the associated energy overheads. To tackle these issues, we propose a polymorphic compression architecture that interleaves these techniques in a unique platform. The proposed architecture allows each application to take advantage of a separate compression/decompression hierarchy (consisting of various types and implementations of hardware/software decoders) tailored to its needs. Simulation results, using different applications (FFT, Matrix multiplication, and WLAN), reveal that the choice of compression hierarchy has a significant impact on compression ratio (up to 52%), decompression energy (up to 4 orders of magnitude), and configuration time (from 33 n to 1.5 s) for the tested applications. Synthesis results reveal that introducing adaptivity incurs negligible additional overheads (1%) compared to the overall platform area.

Scalable and Efficient Configuration of TimeDivision Multiplexed Resources

Consumer-electronics systems are becoming increasingly complex as the number of integrated applications is growing. Some of these applications have real-time requirements, while other non-real-time applications only require good average performance. For cost-efficient design, contemporary platforms feature an increasing number of cores that share resources, such as memories and interconnects. However, resource sharing causes contention that must be resolved by a resource arbiter, such as Time-Division Multiplexing. A key challenge is to configure this arbiter to satisfy the bandwidth and latency requirements of the real-time applications, while maximizing the slack capacity to improve performance of their non-real-time counterparts. As this configuration problem is NP-hard, a sophisticated automated configuration method is required to avoid negatively impacting design time. The main contributions of this article are: 1) An optimal approach that takes an existing integer linear programming (ILP) model addressing the problem and wraps it in a branch-and-price framework to improve scalability. 2) A faster heuristic algorithm that typically provides near-optimal solutions. 3) An experimental evaluation that quantitatively compares the branch-and-price approach to the previously formulated ILP model and the proposed heuristic. 4) A case study of an HD video and graphics processing system that demonstrates the practical applicability of the approach.

A New Electronic Approach for the Surgical Safety Checklist

To improve surgical safety, and to reduce the mortality and surgical complications incidence, the World Health Organization (WHO) developed the Surgical Safety Checklist (SSC). The SSC is a support of information that aids health professionals to reduce the number of complications, induction of anaesthesia, period before skin incision and period before leaving the operating room (OR). The SSC was tested in several countries of the world and their results shown that after introduction of the SSC the incidence of patient complication lowered from 11.0% to 7.0% (P<0.001), the rate of death declined from 1.5% to 0.8% (P = 0.003) and the nurses recognized that patients identity was more often con rmed (81.6% to 94.2%, P<0.01) in many institutions. Recently the SSC was also implemented in Portuguese hospitals, which led us to its study in the real clinical environment. An observational study was performed: several health professionals were observed and interviewed, to understand the functioning of the SSC in an OR, during the clinical routine. The objective of this study was to understand the current use of the SSC, and how it may be improved in terms of usability, taking advantage of the technological advancements such as mobile applications. During two days were observed 14 surgeries, only 2 surgeries met the requirements for the three phases of the SSC, as de ned by the WHO. Of the remaining 12 observed surgeries, 9 surgeries completed the last phase at the correct time. It was also observed that only in 2 surgeries all the phases of the SSC were read aloud to the team and that, in 7 surgeries, several items were read aloud and answered but no one was checking the SSC, only after the end of the phase. The observational study results disclose that several health professionals do not meet with rules of the WHO manual. This study demonstrates that it is urgent to change the mindset of health professionals, and that di erent features in the SSC may be useful to make it more easy to use. With the results of the observational study, a SSC application proposal was developed with new functionalities to improve and aid the health professional in its use. In this application the user can chose between a SSC already created to a speci c surgery or to create a new SSC, adding and adapting some questions from the WHO standard. To create a new SSC, the application is connected to an online questionnaire builder (JotForm). The choice for this online questionnaire builder went through three essential characteristics: number of types of questions, mainly checkbox, radio button and text; the possibility of to create sections inside sections and the API. In addition, in this proposal the improvements are focused in forcing the user to focus in the work ow of the SSC and to save the input timestamps and any actions made by them. Therefore, the following features was implemented to achieve that goal: display one item of the SSC at a time; display the stage where the SSC is; do not allow going back to the previous step; do not allow going forward to the next item if the current is not lled; do not allow going forward to the next item if the time it took to ll the item was too short and log any action made by the user.

Is mental practice an effective adjunct therapeutic strategy for upper limb motor restoration after stroke? A systematic review and meta- analysis

Stroke is one of the most common conditions requiring rehabilitation, and its motor impairments are a major cause of permanent disability. Hemiparesis is observed by 80% of the patients after acute stroke. Neuroimaging studies showed that real and imagined movements have similarities regarding brain activation, supplying evidence that those similarities are based on the same process. Within this context, the combination of mental practice (MP) with physical and occupational therapy appears to be a natural complement based on neurorehabilitation concepts. Our study seeks to investigate if MP for stroke rehabilitation of upper limbs is an effective adjunct therapy. PubMed (Medline), ISI knowledge (Institute for Scientific Information) and SciELO (Scientific Electronic Library) were terminated on 20 February 2015. Data were collected on variables as follows: sample size, type of supervision, configuration of mental practice, setting the physical practice (intensity, number of sets and repetitions, duration of contractions, rest interval between sets, weekly and total duration), measures of sensorimotor deficits used in the main studies and significant results. Random effects models were used that take into account the variance within and between studies. Seven articles were selected. As there was no statistically significant difference between the two groups (MP vs control), showed a - 0.6 (95% CI: -1.27 to 0.04), for upper limb motor restoration after stroke. The present meta-analysis concluded that MP is not effective as adjunct therapeutic strategy for upper limb motor restoration after stroke.

Uma infraestrutura computacional de gestão de dados num contexto de eficiência energética

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para a obtenção do grau de Mestre em Engenharia Electrotécnica e de Computadores

E.D.I.: electronic data interchange

O presente trabalho tem como tema a Troca Electrónica de Dados (Electronic Data Interchange – EDI) transferência de dados estruturados, respeitando mensagens normalizadas estabelecidas, computador a computador, por meios electrónicos. Trocas entre computadores refere-se a trocas entre aplicações informáticas: por exemplo o sistema de encomendas envia ordens ao sistema central de controlo da produção, o qual então fará o envio da respectiva factura. O EDI aberto faz a troca electrónica de dados entre parceiros autónomos que se associaram para fazerem trocas de dados estruturados que são destinados a serem processados por programas de aplicações.

Electronic books

Este documento de trabalho visa apresentar o conceito de electronic book e discutir questões relacionadas com este novo género de publicação e sua aceitação pelo mercado, as vantagens, alguns desafios e principais dificuldades enfrentadas pelos produtores. Com o desenvolvimento das novas tecnologias, emergem novas expectativas em relação às potencialidades do ambiente digital ao que se verifica no meio impresso: custos reduzidos, facilitando a replicação de cópias e a quase livre e imediata distribuição de cópias no mundo inteiro através da Internet.