Stability analysis based on birfurcation theory of the DSTATCOM operating in current control mode

This paper presents the stability analysis for a distribution static compensator (DSTATCOM) that operates in current control mode based on bifurcation theory. Bifurcations delimit the operating zones of nonlinear circuits and, hence, the capability to compute these bifurcations is of important interest for practical design. A control design for the DSTATCOM is proposed. Along with this control, a suitable mathematical representation of the DSTATCOM is proposed to carry out the bifurcation analysis efficiently. The stability regions in the Thevenin equivalent plane are computed for different power factors at the point of common coupling. In addition, the stability regions in the control gain space, as well as the contour lines for different Floquet multipliers are computed. It is demonstrated through bifurcation analysis that the loss of stability in the DSTATCOM is due to the emergence of a Neimark bifurcation. The observations are verified through simulation studies.

Single nucleotide polymorphism (SNP) - genotyping of Community Acquired Methicillin-Resistant Staphylococcus aureus, including the subtyping of PVL toxin producers using Real-Time PCR

Staphylococcus aureus is a common pathogen that causes a variety of infections including soft tissue infections, impetigo, septicemia toxic shock and scalded skin syndrome. Traditionally, Methicillin-Resistant Staphylococcus aureus (MRSA) was considered a Hospital-Acquired (HA) infection. It is now recognised that the frequency of infections with MRSA is increasing in the community, and that these infections are not originating from hospital environments. A 2007 report by the Centers for Disease Control and Prevention (CDC) stated that Staphylococcus aureus is the most important cause of serious and fatal infections in the USA. Community-Acquired MRSA (CA-MRSA) are genetically diverse and distinct, meaning they are able to be identified and tracked by way of genotyping. Genotyping of MRSA using Single nucleotide polymorphisms (SNPs) is a rapid and robust method for monitoring MRSA, specifically ST93 (Queensland Clone) dissemination in the community. It has been shown that a large proportion of CA-MRSA infections in Queensland and New South Wales are caused by ST93. The rationale for this project was that SNP analysis of MLST genes is a rapid and cost-effective method for genotyping and monitoring MRSA dissemination in the community. In this study, 16 different sequence types (ST) were identified with 41% of isolates identified as ST93 making it the predominate clone. Males and Females were infected equally with an average patient age of 45yrs. Phenotypically, all of the ST93 had an identical antimicrobial resistance pattern. They were resistant to the β-lactams – Penicillin, Flu(di)cloxacillin and Cephalothin but sensitive to all other antibiotics tested. Virulence factors play an important role in allowing S. aureus to cause disease by way of colonising, replication and damage to the host. One virulence factor of particular interest is the toxin Panton-Valentine leukocidin (PVL), which is composed of two separate proteins encoded by two adjacent genes. PVL positive CA-MRSA are shown to cause recurrent, chronic or severe skin and soft tissue infections. As a result, it is important that PVL positive CA-MRSA is genotyped and tracked. Especially now that CA-MRSA infections are more prevalent than HA-MRSA infections and are now deemed endemic in Australia. 98% of all isolates in this study tested positive for the PVL toxin gene. This study showed that PVL is present in many different community based ST, not just ST93, which were all PVL positive. With this toxin becoming entrenched in CA-MRSA, genotyping would provide more accurate data and a way of tracking the dissemination. PVL gene can be sub-typed using an allele-specific Real-Time PCR (RT-PCR) followed by High resolution meltanalysis. This allows the identification of PVL subtypes within the CA-MRSA population and allow the tracking of these clones in the community.

Modeling, stability analysis and control of microgrid

With the increase in the level of global warming, renewable energy based distributed generators (DGs) will increasingly play a dominant role in electricity production. Distributed generation based on solar energy (photovoltaic and solar thermal), wind, biomass, mini-hydro along with use of fuel cells and micro turbines will gain considerable momentum in the near future. A microgrid consists of clusters of load and distributed generators that operate as a single controllable system. The interconnection of the DG to the utility/grid through power electronic converters has raised concern about safe operation and protection of the equipments. Many innovative control techniques have been used for enhancing the stability of microgrid as for proper load sharing. The most common method is the use of droop characteristics for decentralized load sharing. Parallel converters have been controlled to deliver desired real power (and reactive power) to the system. Local signals are used as feedback to control converters, since in a real system, the distance between the converters may make the inter-communication impractical. The real and reactive power sharing can be achieved by controlling two independent quantities, frequency and fundamental voltage magnitude. In this thesis, an angle droop controller is proposed to share power amongst converter interfaced DGs in a microgrid. As the angle of the output voltage can be changed instantaneously in a voltage source converter (VSC), controlling the angle to control the real power is always beneficial for quick attainment of steady state. Thus in converter based DGs, load sharing can be performed by drooping the converter output voltage magnitude and its angle instead of frequency. The angle control results in much lesser frequency variation compared to that with frequency droop. An enhanced frequency droop controller is proposed for better dynamic response and smooth transition between grid connected and islanded modes of operation. A modular controller structure with modified control loop is proposed for better load sharing between the parallel connected converters in a distributed generation system. Moreover, a method for smooth transition between grid connected and islanded modes is proposed. Power quality enhanced operation of a microgrid in presence of unbalanced and non-linear loads is also addressed in which the DGs act as compensators. The compensator can perform load balancing, harmonic compensation and reactive power control while supplying real power to the grid A frequency and voltage isolation technique between microgrid and utility is proposed by using a back-to-back converter. As utility and microgrid are totally isolated, the voltage or frequency fluctuations in the utility side do not affect the microgrid loads and vice versa. Another advantage of this scheme is that a bidirectional regulated power flow can be achieved by the back-to-back converter structure. For accurate load sharing, the droop gains have to be high, which has the potential of making the system unstable. Therefore the choice of droop gains is often a tradeoff between power sharing and stability. To improve this situation, a supplementary droop controller is proposed. A small signal model of the system is developed, based on which the parameters of the supplementary controller are designed. Two methods are proposed for load sharing in an autonomous microgrid in rural network with high R/X ratio lines. The first method proposes power sharing without any communication between the DGs. The feedback quantities and the gain matrixes are transformed with a transformation matrix based on the line R/X ratio. The second method involves minimal communication among the DGs. The converter output voltage angle reference is modified based on the active and reactive power flow in the line connected at point of common coupling (PCC). It is shown that a more economical and proper power sharing solution is possible with the web based communication of the power flow quantities. All the proposed methods are verified through PSCAD simulations. The converters are modeled with IGBT switches and anti parallel diodes with associated snubber circuits. All the rotating machines are modeled in detail including their dynamics.

Researching with the Aboriginal Community, MPH2057- Aboriginal Health Course (Monash University), delivered by the Victorian Aboriginal Community Controlled Health Organisation (VACCHO) & The Burnet Institute at The Burnet Institute, Melbourne, Victoria, 29 September 2010

A copy of the slide presentation titled 'Researching with the Aboriginal Community'. It was presented by Bronwyn Fredericks for the Master of Public Health Program (MPH2057- Aboriginal Health Course) at Monash University. The Monash University Aboriginal Health Course (MPH2057) is delivered in partnership by the Victorian Aboriginal Community Controlled Health Organisation (VACCHO) & The Burnet Institute. The 2010 Aboriginal Health Course was run on Level 3 of The Burnet Institute, 89 Commercial Road, Prahan, Melbourne, Victoria, 29 September 2010.

Social inclusion through community enterprise? Examining the available evidence

In recent years the concepts of social inclusion and exclusion have become part of the repertoire of third-way policy discourses that seek to respond to complex socioeconomic problems through processes of 'joined-up' and 'integrated' governance. As part of this approach, we are witnessing an increased focus on the role of the third sector in facilitating social inclusion. While the push towards governing through networks has gained moral legitimacy in some areas of social policy, the practical legitimacy - that is, whether these new approaches actually produce demonstrably better outcomes than more traditional policy approaches - remains largely unsubstantiated. This article contributes to the evidence base, by examining the social-inclusion impacts of eleven community enterprises operating in Victoria, and to the wider available evidence on the social, economic and civic effects of social enterprise.

Influences of age and mechanical stability on volume, microstructure, and mineralization of the fracture callus during bone healing : Is osteoclast activity the key to age-related impaired healing?

Earlier studies have shown that the influence of fixation stability on bone healing diminishes with advanced age. The goal of this study was to unravel the relationship between mechanical stimulus and age on callus competence at a tissue level. Using 3D in vitro micro-computed tomography derived metrics, 2D in vivo radiography, and histology, we investigated the influences of age and varying fixation stability on callus size, geometry, microstructure, composition, remodeling, and vascularity. Compared were four groups with a 1.5-mm osteotomy gap in the femora of Sprague–Dawley rats: Young rigid (YR), Young semirigid (YSR), Old rigid (OR), Old semirigid (OSR). Hypothesis was that calcified callus microstructure and composition is impaired due to the influence of advanced age, and these individuals would show a reduced response to fixation stabilities. Semirigid fixations resulted in a larger ΔCSA (Callus cross-sectional area) compared to rigid groups. In vitro μCT analysis at 6 weeks postmortem showed callus bridging scores in younger animals to be superior than their older counterparts (pb0.01). Younger animals showed (i) larger callus strut thickness (pb0.001), (ii) lower perforation in struts (pb0.01), and (iii) higher mineralization of callus struts (pb0.001). Callus mineralization was reduced in young animals with semirigid fracture fixation but remained unaffected in the aged group. While stability had an influence, age showed none on callus size and geometry of callus. With no differences observed in relative osteoid areas in the callus ROI, old as well as semirigid fixated animals showed a higher osteoclast count (pb0.05). Blood vessel density was reduced in animals with semirigid fixation (pb0.05). In conclusion, in vivo monitoring indicated delayed callus maturation in aged individuals. Callus bridging and callus competence (microstructure and mineralization) were impaired in individuals with an advanced age. This matched with increased bone resorption due to higher osteoclast numbers. Varying fixator configurations in older individuals did not alter the dominant effect of advanced age on callus tissue mineralization, unlike in their younger counterparts. Age-associated influences appeared independent from stability. This study illustrates the dominating role of osteoclastic activity in age-related impaired healing, while demonstrating the optimization of fixation parameters such as stiffness appeared to be less effective in influencing healing in aged individuals.

Money laundering and FATF compliance by the international community

This paper examines the anti-money laundering systems of Australia, the United Arab Emirates (UAE), the United Kingdom (UK) and the United States of America (USA), the extent to which they have implemented the Financial Action Task Force (FATF) recommendations, and how compliance with these recommendations is affected by local cultural and economic factors. The paper makes use of FATF evaluation reports to compare the countries’ compliance; it examines some of the underlying cultural considerations and culture-specific ethical issues that affect the extent of compliance, and how cultural and ethical considerations may affect good governance. The findings indicate that the UK and the USA are the most advanced with regards to their compliance with the FATF recommendations and Australia and the UAE less so. The UAE is in particular found to be least compliant. We relate this finding to previous work on how a country’s legal and financial systems develop in line with its religion, culture and socio-economic situation, and examine how such local factors have affected the UAE’s financial and anti-money laundering and combating the financing of terrorism (AML/CFT) systems. This research will be of interest to policy-makers and government agencies involved in addressing money laundering and its successful detection and prosecution.

Fuzzy logic power system stabilizer in multimachine stability studies

Power system stabilizers (PSS) work well at the particular network configuration and steady state conditions for which they were designed. Once conditions change, their performance degrades. This can be overcome by an intelligent nonlinear PSS based on fuzzy logic. Such a fuzzy logic power system stabilizer (FLPSS) is developed, using speed and power deviation as inputs, and provides an auxiliary signal for the excitation system of a synchronous motor in a multimachine power system environment. The FLPSS's effect on the system damping is then compared with a conventional power system stabilizer's (CPSS) effect on the system. The results demonstrate an improved system performance with the FLPSS and also that the FLPSS is robust

Stability and convergence of an effective numerical method for the time-space fractional Fokker-Planck equation with a nonlinear source term

Fractional Fokker-Planck equations (FFPEs) have gained much interest recently for describing transport dynamics in complex systems that are governed by anomalous diffusion and nonexponential relaxation patterns. However, effective numerical methods and analytic techniques for the FFPE are still in their embryonic state. In this paper, we consider a class of time-space fractional Fokker-Planck equations with a nonlinear source term (TSFFPE-NST), which involve the Caputo time fractional derivative (CTFD) of order α ∈ (0, 1) and the symmetric Riesz space fractional derivative (RSFD) of order μ ∈ (1, 2). Approximating the CTFD and RSFD using the L1-algorithm and shifted Grunwald method, respectively, a computationally effective numerical method is presented to solve the TSFFPE-NST. The stability and convergence of the proposed numerical method are investigated. Finally, numerical experiments are carried out to support the theoretical claims.

Creativity, knowledge, engagement : keys to finding the right governance model for a regional community precinct

This paper investigates the Cooroy Mill community precinct (Sunshine Coast, Queensland), as a case study, seeking to understand the way local dynamics interplay and work with the community strengths to build a governance model of best fit. As we move to an age of ubiquitous computing and creative economies, the definition of public place and its governance take on new dimensions, which – while often utilizing models of the past – will need to acknowledge and change to the direction of the future. This paper considers a newly developed community precinct that has been built on three key principles: to foster creative expression with new media, to establish a knowledge economy in a regional area, and to subscribe to principles of community engagement. The study involved qualitative interviews with key stakeholders and a review of common practice models of governance along a spectrum from community control to state control. The paper concludes with a call for governance structures that are locally situated and tailored, inclusive, engaging, dynamic and flexible in order to build community capacity, encourage creativity, and build knowledge economies within emerging digital media cityscapes.

Incorporating community history into urban redevelopment

A community history project must be relevant to each person within it so that they see themselves as part of the socio-cultural fabric of the area and feel a sense of ownership of their environment. The Mill Albion community history project is a diverse, multi-layered public history/art program that captures the social heritage of The Mill Albion and allows the community to contribute to their ongoing history. The Albion Flour Mill was built in 1930 at a time when Australia was feeling the effects of its worst economic depression and continued operations for more than 72 years. After ceasing operation in 2005 the site was left to deteriorate. The FKP Property Group purchased the land to undertake a new urban redevelopment project, drawing on the design principles of a traditional ‘village’, while valuing the importance of remembering the community that once included the Flour Mill. This paper reflects on the this project and showcases some of the culturally creative ways this community’s history was told, using methods such as digital stories, contemporary and historical photography and oral history.

Fa'afaletui : a framework for the promotion of kidney health in an Australian Samoan community

Purpose Samoan communities in Australia exhibit a disproportionate rate of kidney disease compared with other Australians. This article describes a research project that used a culturally sensitive framework, Fa’afaletui, to help reduce the barriers of language and culture and increase our understanding of the factors contributing to kidney disease, in one Samoan community in Australia. Design Semistructured group interviews were undertaken with Samoan community families and groups. The interviews were analyzed according to key concepts embedded in the Fa’afaletui framework. Findings Four factors associated with health risks in this Samoan community emerged—diet and exercise; issues related to the collective (incorporating the village, church, and family); tapu or cultural protocols; and the importance of language. Conclusions The findings suggest that future kidney health promotion initiatives within this Samoan community will be more effective if they are sensitive to Samoan cultural norms, language, and context.

The old face of 'new' social networks : the republic of letters as a virtual community

This paper explores the idea of virtual participation through the historical example of the republic of letters in early modern Europe (circa 1500-1800). By reflecting on the construction of virtuality in a historical context, and more specifically in a pre-digital environment, this paper calls attention to accusations of technological determinism in ongoing research concerning the affordances of the Internet and related media of communication. It argues that ‘the virtual’ is not synonymous with ‘the digital’ and suggests that, in order to articulate what is novel about modern technologies, we must first understand the social interactions underpinning the relationships which are facilitated through those technologies. By analysing the construction of virtuality in a pre-digital environment, this paper thus offers a baseline from which scholars might consider what is different about the modes of interaction and communication being engaged in via modern media.

Aboriginal community control and decolonizing health policy : a yarn from Australia

This chapter outlines: a brief history of Australian Aboriginal health and health policy and then moves on to demonstrate how the Victorian Aboriginal Community Controlled Health Organisation (VACCHO) undertakes its work and is an example of 'decolonizing policy in action'. Moreover, it highlights how Aboriginal participation in the development of policy and in the planning, delivery, management and evaluation of health programs enables policies and programs to respond effectively to the needs of Aboriginal people and to change future health outcomes for them. It showcases how Aboriginal decision-making has gone some way to decolonizing policymaking and has addressed the power imbalance - both of which have been critical in the improvement in Aboriginal health outcomes.