An HPLC-UV method for the measurement of permeability of marker drugs in the Caco-2 cell assay

The Caco-2 cell line has been used as a model to predict the in vitro permeability of the human intestinal barrier. The predictive potential of the assay relies on an appropriate in-house validation of the method. The objective of the present study was to develop a single HPLC-UV method for the identification and quantitation of marker drugs and to determine the suitability of the Caco-2 cell permeability assay. A simple chromatographic method was developed for the simultaneous determination of both passively (propranolol, carbamazepine, acyclovir, and hydrochlorothiazide) and actively transported drugs (vinblastine and verapamil). Separation was achieved on a C18 column with step-gradient elution (acetonitrile and aqueous solution of ammonium acetate, pH 3.0) at a flow rate of 1.0 mL/min and UV detection at 275 nm during the total run time of 35 min. The method was validated and found to be specific, linear, precise, and accurate. This chromatographic system can be readily used on a routine basis and its utilization can be extended to other permeability models. The results obtained in the Caco-2 bi-directional transport experiments confirmed the validity of the assay, given that high and low permeability profiles were identified, and P-glycoprotein functionality was established.

Evaluation of total carotenoids, alpha- and beta-carotene in carrots (Daucus carota L.) during home processing

This study aims to analyze the influence of dehydration and different preparation methods during home processing related toalpha-carotene, beta-carotene and total carotenoids stability in carrots. Vitamin A values were evaluated after different treatments. Thus, carrots were submitted to steam cooking, water cooking with and without pressure, moist/dry cooking and conventional dehydration. Determination of alpha- and beta-carotenes was made by High-Performance Liquid Chromatography (HPLC) (conditions were developed by us) using spectrophotometric detection visible-UV at 470 nm; a RP-18 column and methanol: acetonitrile: ethyl acetate (80: 10: 10) as mobile phase. Total carotenoids quantification was made by 449 nm spectrophotometer. The retention of the analyzed carotenoids ranged from 60.13 to 85.64%. Water cooking without pressure promoted higher retention levels of alpha- and beta-carotene and vitamin A values, while water cooking with pressure promoted higher retention levels of total carotenoids. Dehydration promoted the highest carotenoid losses. The results showed that, among the routinely utilized methods under domestic condition, cooking without pressure, if performed under controlled time and temperature, is the best method as it reduces losses in the amount of alpha- and beta-carotene, the main carotenoids present in the carrots. Despite the significant carotenoid losses, carrots prepared through domestic methods, remain a rich source of provitamin A.

A method for fast determination of epigallocatechin gallate (EGCG), epicatechin (EC), catechin (C) and caffeine (CAF) in green tea using HPLC

Tea has been considered a medicine and a healthy beverage since ancient times, but recently it has received a great deal of attention because of its antioxidant properties. Green tea polyphenols have demonstrated to be an effective chemopreventive agent. Recently, investigators have found that EGCG, one of the green tea catechins, could have anti-HIV effects when bound to CD4 receptor. Many factors can constitute important influences on the composition of tea, such as species, season, age of the leaf, climate, and horticultural practices (soil, water, minerals, fertilizers). This paper presents an HPLC analytical methodology development, using column RP-18 and mobile phase composed by water, acetonitrile, methanol, ethyl acetate, glacial acetic acid (89:6:1:3:1 v/v/v/v/v) for simultaneous determination and quantification of caffeine (CAF), catechin (C), epicatechin (EC) and epigallocatechin gallate (EGCG) in samples of Camellia sinensis (green tea) grown in Brazil and harvested in spring, in summer and in autumn, in comparison to Brazilian black tea, to samples of Japanese and Chinese green tea and to two standardized dry extracts of green tea. The method has been statistically evaluated and has proved to be adequate to qualitative and quantitative determination of the samples.

The development of automated methods for the determination of trace concentrations of carbomate pesticides in water using solid sorbent pre-concentration methods and high performance liquid chromatography /

Several automated reversed-phase HPLC methods have been developed to determine trace concentrations of carbamate pesticides (which are of concern in Ontario environmental samples) in water by utilizing two solid sorbent extraction techniques. One of the methods is known as on-line pre-concentration'. This technique involves passing 100 milliliters of sample water through a 3 cm pre-column, packed with 5 micron ODS sorbent, at flow rates varying from 5-10 mUmin. By the use of a valve apparatus, the HPLC system is then switched to a gradient mobile phase program consisting of acetonitrile and water. The analytes, Propoxur, Carbofuran, Carbaryl, Propham, Captan, Chloropropham, Barban, and Butylate, which are pre-concentrated on the pre-column, are eluted and separated on a 25 cm C-8 analytical column and determined by UV absorption at 220 nm. The total analytical time is 60 minutes, and the pre-column can be used repeatedly for the analysis of as many as thirty samples. The method is highly sensitive as 100 percent of the analytes present in the sample can be injected into the HPLC. No breakthrough of any of the analytes was observed and the minimum detectable concentrations range from 10 to 480 ng/L. The developed method is totally automated for the analysis of one sample. When the above mobile phase is modified with a buffer solution, Aminocarb, Benomyl, and its degradation product, MBC, can also be detected along with the above pesticides with baseline resolution for all of the analytes. The method can also be easily modified to determine Benomyl and MBC both as solute and as particulate matter. By using a commercially available solid phase extraction cartridge, in lieu of a pre-column, for the extraction and concentration of analytes, a completely automated method has been developed with the aid of the Waters Millilab Workstation. Sample water is loaded at 10 mL/min through a cartridge and the concentrated analytes are eluted from the sorbent with acetonitrile. The resulting eluate is blown-down under nitrogen, made up to volume with water, and injected into the HPLC. The total analytical time is 90 minutes. Fifty percent of the analytes present in the sample can be injected into the HPLC, and recoveries for the above eight pesticides ranged from 84 to 93 percent. The minimum detectable concentrations range from 20 to 960 ng/L. The developed method is totally automated for the analysis of up to thirty consecutive samples. The method has proven to be applicable to both purer water samples as well as untreated lake water samples.

Effects of sample solvent composition and injection volume on chromatographic peak profiles of methyl w- benzimidazolecarbamate and 3-butyl1-2,4-dioxo[1,2-a]-s- triazinobenzimidazole in RP-HPLC

The effects of sample solvent composition and the injection volume, on the chromatographic peak profiles of two carbamate derivatives, methyl 2-benzimidazolecarbamate (MBC) and 3-butyl-2,4-dioxo[1,2-a]-s-triazinobenzimidazole (STB), were studied using reverse phase high performance liquid chromatograph. The study examined the effects of acetonitrile percentage in the sample solvent from 5 to 50%, effects of methanol percentage from 5 to 50%, effects of pH increase from 4.42 to 9.10, and effect of increasing buffer concentration from ° to 0.12M. The effects were studied at constant and increasing injection mass and at four injection volumes of 10, 50, 100 and 200 uL. The study demonstrated that the amount and the type of the organic solvents, the pH, and the buffer strength of the sample solution can have a pronounced effect on the peak heights, peak widths, and retention times of compounds analysed. MBC, which is capable of intramolecular hydrogen bonding and has no tendency to ionize, showed a predictable increase .in band broadening and a decrease in retention times at higher eluting strengths of the sample solvent. STB, which has a tendency to ionize or to strongly interact with the sample solvent, was influenced in various ways by the changes in ths sample solvent composition. The sample solvent effects became more pronounced as the injection volume increased and as the percentage of organic solvent in the sample solution became greater. The peak height increases for STB at increasing buffer concentrations became much more pronounced at higher analyte concentrations. It was shown that the widely accepted procedure of dissolving samples in the mobile phase does not yield the most efficient chromatograms. For that reason samples should be dissolved in the solutions with higher aqueous content than that of the mobile phase whenever possible. The results strongly recommend that all the samples and standards, regardless whether the standards are external or internal, be analysed at a constant sample composition and a constant injection volume.

NMR studies of the exchange reactions of CH3CN.BX3 with excess CH3CN /|nJoseph Fogelman. -- 260 St. Catharines, Ont. : [s. n.],

Exchange reactions between molecular complexes and excess acid or base are well known and have been extensively surveyed in the literature(l). Since the exchange mechanism will, in some way involve the breaking of the labile donor-acceptor bond, it follows that a discussion of the factors relating to bonding in molecular complexes will be relevant. In general, a strong Lewis base and a strong Lewis acid form a stable adduct provided that certain stereochemical requirements are met. A strong Lewis base has the following characteristics (1),(2) (i) high electron density at the donor site. (ii) a non-bonded electron pair which has a low ionization potential (iii) electron donating substituents at the donor atom site. (iv) facile approach of the site of the Lewis base to the acceptor site as dictated by the steric hindrance of the substituents. Examples of typical Lewis bases are ethers, nitriles, ketones, alcohols, amines and phosphines. For a strong Lewis acid, the following properties are important:( i) low electron density at the acceptor site. (ii) electron withdrawing substituents. (iii) substituents which do not interfere with the close approach of the Lewis base. (iv) availability of a vacant orbital capable of accepting the lone electron pair of the donor atom. Examples of Lewis acids are the group III and IV halides such (M=B, AI, Ga, In) and MX4 - (M=Si, Ge, Sn, Pb). The relative bond strengths of molecular complexes have been investigated by:- (i) (ii) (iii) (iv) (v] (vi) dipole moment measurements (3). shifts of the carbonyl peaks in the IIIR. (4) ,(5), (6) .. NMR chemical shift data (4),(7),(8),(9). D.V. and visible spectrophotometric shifts (10),(11). equilibrium constant data (12), (13). heats of dissociation and heats of reactions (l~), (16), (17), (18), (19). Many experiments have bben carried out on boron trihalides in order to determine their relative acid strengths. Using pyridine, nitrobenzene, acetonitrile and trimethylamine as reference Lewis bases, it was found that the acid strength varied in order:RBx3 > BC1 3 >BF 3 • For the acetonitrile-boron trihalide and trimethylamine boron trihalide complexes in nitrobenzene, an-NMR study (7) showed that the shift to lower field was. greatest for the BB~3 adduct ~n~ smallest for the BF 3 which is in agreement with the acid strengths. If electronegativities of the substituents were the only important effect, and since c~ Br ,one would expect the electron density at the boron nucleus to vary as BF3acetonitrile boron trihalide complex is formed, the boron atom undergoes ~_cbange of hybridization from sp2 to sp3. From a linear relationship between the heat of formation of ethyl acetate adducts and the shift in the carbonyl I.R. stretch, Drago (22) et al have proposed that the angular di~tortion of the X-B-X bonds from sp2 (12 ) to sp3 (10 hybridization is proportional to the amount of charge transferred, i.e. to the nature of the base, and they have rejected the earlier concept of reorganization energy in explaining the formation of the adduct bond (19).

Synthesis and properties of some 4H-1, 3, 4 benzothiadiazines /|nby Darko J. Vukov. -- 260 St. Catharines, Ont. : [s. n.],

The work herein has been divided into five sections. In the first section, a new method of converting N-aroyl- hydrazines to hydrazidic halides is described. The second section deals with the products of reaction of hydrazidic halides with thioacetate ion in acetonitrile at room temperature. A number of new acetylthiohydrazides has been isolated together with corresponding hyclrazidic sulphides. Examination of x-ray data for bis-[~ -(2,6- dibromophenylhydrazono) - benZYl] sulphide revealpd the symmetrical structure as the most probable. In the third section, which consists of the three subsections, the synthesis of the 4H-l,3,4 benzothiadiazine ring system has been extended to 4H-l,3,4 benzothiadiazines with substituents in the 5 and 6-positions. Extension of synthesis also involves 4H-l,3,4 benzothiadiazines with mora than one substituent. Nuclear magnetic resonance spectra of 5 and 6 substituted 4H-l,3,4 benzothiadiazines have been ,. recorded. The section ends with a discussion of the mass spectra of some 4H-l.3,4 benzothiadiazines. In the fourth section, which is divided into two sub- -sections, preparation of 7-nitro substituted 4H-l,3,4 benzothiadiazine from N-thiobenzoyl hydrazine and2,4-dinitro -fluorobenzene is found to be satisfactory. Thiohydrazides react with acetic anhydride, in some cases, to give products identical with acetylthiohydrazides obtained from the hydrazidic halides with thioacetate ion at room temperature. In most of the cases thiohydrazides are found to give anomalous products on reaction with acetic anhydride and mechanisms for their formation are discussed. In the fifth section, which forms three subsections, the 4H-l,3,4 benzothiadiazine ring system with a halogen substituent in the 7-position undergoes electrophilic attack preferentially in 5-posi tion. \fuen the 5-posi tion is occupied by a halogen atom, electrophilic substitution occurs at the 7-position of 4H-l,3,4 benzothiadiazine ring system. Substitution at the 4-nitrogen atom in 4H w l,3,4 benzo- -thiadiazine is extremely slow, probably due to delocalisa- -tion of the nitrogen lone pair in the system. Oxidation of 4H-l,3,4 benzothiadiazines occurs at the sulphur atom under relatively mild conditions. t The Appendix deals with the reaction of N-benzoyl-N - -(2,5-dibromophenyl)hydrazine with p-nitrothiophenol~ The proposed p-nitrothiophenoxy - intermediate may undergo benzothiadiazine formation in a proton exchange system.

The determination of sinigrin in Brassica, and investigations into the use of allyl-isothiocyanate as a nematicide

The goal of this thesis was to study factors related to the development of Brassica juncea as a sustainable nematicide. Brassica juncea is characterized by the glycoside (glucosinolate) sinigrin. Various methods were developed for the determination of sinigrin in Brassica juncea tissue extracts. Sinigrin concentrations in plant tissues at various stages of growth were monitored. Sinigrin enzymatically breaks down into allylisothiocyanate (AITC). AITC is unstable in aqueous solution and degradation was studied in water and in soil. Finally, the toxicity of AITC against the root-lesion nematode (Pratylenchus penetrans) was determined. A method was developed to extract sinigrin from whole Brassica j uncea tissues. The optimal time of extraction wi th boiling phosphate buffer (0.7mM, pH=6.38) and methanol/water (70:30 v/v) solutions were both 25 minutes. Methanol/water extracted 13% greater amount of sinigrin than phosphate buffer solution. Degradation of sinigrin in boiling phosphate buffer solution (0.13%/minute) was similar to the loss of sinigrin during the extraction procedure. The loss of sinigrin from boiling methanol/water was estimated to be O.Ol%/minute. Brassica juncea extract clean up was accomplished by an ion-pair solid phase extraction (SPE) method. The recovery of sinigrin was 92.6% and coextractive impurities were not detected in the cleaned up extract. Several high performance liquid chromatography (HPLC) methods were developed for the determination of sinigrin. All the developed methods employed an isocratic mobile phase system wi th a low concentration of phosphate buffer solution, ammonium acetate solution or an ion-pair reagent solution. A step gradient system was also developed. The method involved preconditioning the analytical column with phosphate buffer solution and then switching the mobile phase to 100% water after sample injection.Sinigrin and benzyl-glucosinolate were both studied by HPLC particle beam negative chemical ionization mass spectrometry (HPLCPB- NCI-MS). Comparison of the mass spectra revealed the presence of fragments arising from the ~hioglucose moiety and glucosinolate side-chain. Variation in the slnlgrin concentration within Brassica juncea plants was studied (Domo and Cutlass cuItivars). The sinigrin concentration in the top three leaves was studied during growth of each cultivar. For Cutlass, the minimum (200~100~g/g) and maximum (1300~200~g/g) concentrations were observed at the third and seventh week after planting, respectively. For Domo, the minimum (190~70~g/g) and maximum (1100~400~g/g) concentrations were observed at the fourth and eighth week after planting, respectively. The highest sinigrin concentration was observed in flower tissues 2050±90~g/g and 2300±100~g/g for Cutlass and Domo cultivars, respectively. Physical properties of AITC were studied. The solubility of AITC in water was determined to be approximately 1290~g/ml at 24°C. An HPLC method was developed for the separation of degradation compounds from aqueous AITC sample solutions. Some of the degradation compounds identified have not been reported in the literature: allyl-thiourea, allyl-thiocyanate and diallyl-sulfide. In water, AITC degradation to' diallyl-thiourea was favored at basic pH (9.07) and degradation to diallyl-sulfide was favored at acidic pH (4 . 97). It wap necessary to amend the aqueous AITC sample solution with acetonitrile ?efore injection into the HPLC system. The acetonitrile amendment considerably improved AITC recovery and the reproducibility of the results. The half-life of aqueous AITC degradation at room temperature did not follow first-order kinetics. Beginning with a 1084~g/ml solution, the half-life was 633 hours. Wi th an ini tial AITC concentration of 335~g/ml the half-life was 865 hours. At 35°C the half-life AITC was 76+4 hours essentially independent of the iiisolution pH over the range of pH=4.97 to 9.07 (1000~g/ml). AITC degradation was also studied in soil at 35°C; after 24 hours approximately 75% of the initial AITC addition was unrecoverable by water extraction. The ECso of aqueous AITC against the root-lesion nematode (Pratylenchus penetrans) was determined to be approximately 20~g/ml at one hour exposure of the nematode to the test solution. The toxicological study was also performed with a myrosinase treated Brassica juncea extract. Myrosinase treatment of the Brassica juncea extract gave nearly quantitative conversion of sinigrin into AITC. The myrosinase treated extract was of the same efficacy as an aqueous AITC solution of equivalent concentration. The work of this thesis was focused upon understanding parameters relevant to the development of Brassica juncea as a sustainable nematicide. The broad range of experiments were undertaken in support of a research priority at Agriculture and Agri-Food Canada.

Investigations into the determination of polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) by capillary gas chromatography

Factors involved in the determination of PAHs (16 priority PAHs as an example) and PCBs (10 PCB congeners, representing 10 isomeric groups) by capillary gas chromatography coupled with mass spectrometry (GC/MS, for PAHs) and electron capture detection (GC/ECD , for PCBs) were studied, with emphasis on the effect of solvent. Having various volatilities and different polarities, solvent studied included dichloromethane, acetonitrile, hexan e, cyclohexane, isooctane, octane, nonane, dodecane, benzene, toluene, p-xylene, o-xylene, and mesitylene. Temperatures of the capillary column, the injection port, the GC/MS interface, the flow rates of carrier gas and make-up gas, and the injection volume were optimized by one factor at a time method or simplex optimization method. Under the optimized conditions, both peak height and peak area of 16 PAHs, especially the late-eluting PAHs, were significantly enhanced (1 to 500 times) by using relatively higher boiling point solvents such as p-xylene and nonane, compared with commonly used solvents like benzene and isooctane. With the improved sensitivity, detection limits of between 4.4 pg for naphthalene and 30.8 pg for benzo[g,h,i]perylene were obtained when p-xylene was used as an injection solvent. Effect of solvent on peak shape and peak intensity were found to be greatly dependent on temperature parameters, especially the initial temperature of the capillary column. The relationship between initial temperature and shape of peaks from 16 PAHs and 10 PCBs were studied and compared when toluene, p-xylene, isooctane, and nonane were used as injection solvents. If a too low initial temperature was used, fronting or split of peaks was observed. On the other hand, peak tailing occurred at a too high initial column temperature. The optimum initial temperature, at which both peak fronting and tailing were avoided and symmetrical peaks were obtained, depended on both solvents and the stationary phase of the column used. On a methyl silicone column, the alkane solvents provided wider optimum ranges of initial temperature than aromatic solvents did, for achieving well-shaped symmetrical GC peaks. On a 5% diphenyl: 1% vinyl: 94% dimethyl polysiloxane column, when the aromatic solvents were used, the optimum initial temperature ranges for solutes to form symmetrical peaks were improved to a similar degree as those when the alkanes were used as injection solvents. A mechanism, based on the properties of and possible interactions among the analyte, the injection solvent, and the stationary phase of the capillary column, was proposed to explain these observations. The effect of initial temperature on peak height and peak area of the 16 PAHs and the 10 PCBs was also studied. The optimum initial temperature was found to be dependent on the physical properties of the solvent used and the amount of the solvent injected. Generally, from the boiling point of the solvent to 10 0C above its boiling point was an optimum range of initial temperature at which cthe highest peak height and peak area were obtained.

Half-sandwich silane complexes of ruthenium and iron : synthesis, structure and application to catalysis

The present thesis describes syntheses, structural studies, and catalytic reactivity of new non-classical silane complexes of ruthenium and iron. The ruthenium complexes CpRu(PPri3)CI(T]2-HSiR3) (1) (SiR3 = SiCh (a), SiClzMe (b), SiCIMe2 (c), SiH2Ph (d), SiMe2Ph (e» were prepared by reactions of the new unsaturated complex CpRu(PPri3)CI with silanes. According to NMR studies and X-ray analyses, the complexes la-c exhibit unusual simultaneous Si··· H and Si··· CI-Ru interactions. The complex CpRu(PPri3)CI was also used for the preparation of the first examples of late transition metal agostic silylamido complexes CpRu(PPri3)(N(T]2-HSiMe2)R) (2) (R= Ar or But), which were characterized by NMR spectroscopy. The iron complexes CpFe(PMePri2)H2(SiR3) (3) (SiR3 = SiCh (a), SiClzMe (b), SiCIMe2 (c), SiH2Ph (d), SiMe2Ph (e» were synthesized by the reaction of the new borohydride iron complex CpFe(PMePri2)(B~) with silanes in the presence NEt3. The complexes 3 exhibit unprecedented two simultaneous and equivalent Si··· H interactions, which was confirmed by X-ray analyses and DFT calculations. A series of cationic ruthenium complexes [CpRu(PR3)(CH3CN)(112-HSiR'3)]BAF (PR3 = PPri 3 (4), PPh3 (5); SiR'3 = SiCh (a), SiClzMe (b), SiClMe2 (c), SiH2Ph (d), SiMe2Ph (e» was obtained by substitution of one of the labile acetonitrile ligands in [CpRu(PR3)(CH3CNh]BAF with sHanes. Analogous complexes [TpRu(PR3)(CH3CN)(T]2 -HSiR' 3)]BAF (5) were obtained by the reaction of TpRu(PR3)(CH3CN)CI with LiBAF in the presence of silanes. The complexes 4-5 were characterized by NMR spectroscopy, and the observed coupling constants J(Si-H) allowed us to estimate the extent of Si-H bond activation in these compounds. The catalytic activity in hydrosilylation reactions of all of the above complexes was examined. The most promising results were achieved with the cationic ruthenium precatalyst [CpRu(PPri3)(CH3CN)2t (6). Complex 6 shows good to excellent catalytic activity in the hydrosilylation of carbonyls, dehydrogenative coupling of silanes with alcohols, amines, acids, and reduction of acid chlorides. We also discovered very selective reduction of nitriles and pyridines into the corresponding N-silyl imines and l,4-dihydropyridines, respectively, at room temperature with the possibility of catalyst recycling. These chemoselective catalytic methods have no analogues in the literature. The reactions were proposed to proceed via an ionic mechanism with intermediate formation of the silane a-complexes 4.

Triarylamminium radical-cation complexes: design and magnetic properties and Base-catalyzed hydrosilylation: mechanism and substrate scope

1. Triarylamminium radical-cation complexes. The detailed study of manganese, copper and nickel metal-radical complexes with triarylamminium ligands was conducted. Stable, neutral and pseudo-octahedral coordination monometallic complexes with simple monodentate 2,2`-bipyridine ligand containing a redox-active N,N`-(4,4`-dimethoxydiphenyl-amino) substituent were synthesized and fully characterized. The one-electron oxidation process and formation of persistent radical-cation complexes was observed by cyclic voltammetry and spectroelectrochemical measurements. Evans method measurements were performed with radical-cation complexes generated by chemical one-electron oxidation with NOPF6 in acetonitrile. The experimental results indicate ferromagnetic coupling between metal and triarylamminium cation in manganese (II) complex and antiferromagnetic coupling in nickel (II) complex. This data is supported by DFT calculations which also lend weight to the  spin polarization mechanism as an operative model for magnetic exchange coupling. Neutral bimetallic complexes with a new ditopic ligand were synthesized and fully characterized, including magnetic and electrochemical studies. Chemical oxidation of these precursor complexes did not generate radical-cations, but dicationic complexes, which was confirmed by UV-vis and EPR-experiments, as well as varied temperature magnetic measurements. DFT calculations for radical-cation complexes are included. A synthetic pathway for polytopic ligand with multiple redox-active triarylamine sites was developed. The structure of the ligand is presumably suitable for -spin polarization exchange model and allows for production of polymetallic complexes having high spin ground states. 2. Base-catalyzed hydrosilylation. A simple reductive base-catalyzed hydrosilation of aldehydes and ketones was adapted to the use of the cheap, safe, and non-toxic polymethylhydrosiloxane (PMHS) instead of the common PhSiH3 and (EtO)3SiH, which present significant cost and safety concerns, respectively. The conversion of silane into pentacoordinate silicate species upon addition of a base was studied in details for the cases of phenyl silane and PMHS and is believed to be essential for the hydrosilylation process. We discovered that nucleophiles (a base or fluoride-anion) induced the rearrangement of PMHS and TMDS into light silanes: MeSiH3 and Me2SiH2, respectively. The reductive properties of PMHS under basic conditions can be attributed to the formation of methyl silane and its conversion into a silicate species. A procedure for the generation of methyl silane and its use in further efficient reductions of aldehydes and ketones has been developed. The protocol was extended to the selective reduction of esters and tertiary amides into alcohols and aldimines into amines with good isolated yields and reduction of heterocyclic compounds was attempted.

Ring-opening of cycloalkane epoxides and aziridines with aromatic amines : toward the total synthesis of pactamycin

Résumé Cette thèse consiste en trois thèmes résumés dans les paragraphes ci-dessous. L’influence de différents groupements protecteurs du groupe hydroxyle lors des réactions d’ouverture des cis- et trans- 3-hydroxy-1,2-époxycycloalcanes a été étudiée. Il a été montré que Yb(OTf)3 constituait un catalyseur doux pour l’ouverture régiosélective de cycles afin d’obtenir les -anilino cycloalcanols correspondants avec de bons rendements. Le chauffage du milieu réactionnel dans le toluène comme solvant a permis d’augmenter la cinétique de la réaction, au dépend du rendement. La partie aniline a été régiosélectivement introduite en position vicinale du groupe hydroxyle ou éther afin d’obtenir un unique régioisomère. La même tendance a été observée avec les époxydes du 3-azidocyclohex-1-ène et du 3-carbamate correspondant. Le temps de réaction a été réduit lorsque Yb(OTf)3 a été dissous dans l’acétonitrile. Le triflate d’ytterbium (III) a également été utilisé comme catalyseur pour l’ouverture de cycle régiosélective d’aziridines non-activées sur des cyclohexanes portant des substituants azotures ou éthers de benzyle. L’ion azoture ou l’aniline forment les produits trans correspondants, donnant alors accès à des diamines vicinales avec de bons rendements. Un éther ω-alcoxy p-méthoxybenzylique racémique, inhibiteur de HDAC, a été ainsi préparé en huit étapes synthétiques (rendement total de 26%) à partir du 1-((tert-butyldiphénylsilyl)oxy)hept-6-èn-2-ol. Ceci représente un progrès par rapport à la précédente méthode (9 étapes, rendement total de 16%). La métathèse croisée se montre particulièrement efficace et pratique dans cette stratégie et l’alkylation par le trichloroacétimidate de p-méthoxybenzyle en présence de Sc(OTf)3 améliore le rendement global de la synthèse. Un aminoalcool présent dans la pactamycine et contenant le squelette carboné, les groupements fonctionnels et la stéréochimie requise a été synthétisé en 27 étapes à partir de la L-thréonine. La méthodologie décrite dans cette thèse permet la synthèse de cet intermédiaire clé à l’échelle multigramme.

Synthesis, properties and characterization of N-Alkyl substituted b-Diketiminato copper(I) Complexes

Le ligand nacnacxylH (xyl = C6Me2H3) et les ligands dikétimines N-alkyle substitués (nacnacCH(Me)PhH, nacnacBnH and nacnaciPrH) ont été préparés avec de bons rendements à l’exception du nacnaciPrH (23%) en utilisant un protocole en une étape et à l’aide d’un montage Dean-Stark. La réaction du S,S-nacnacCH(Me)PhH et du nacnacBnH avec le nBuLi dans le THF conduit au S,S-nacnacCH(Me)PhLi(THF) et au nacnacBnLi(THF). Les tentatives de bromation de ces composés par le N-bromosuccinimide conduisent plutôt aux ligands S,S-succnacnacCH(Me)PhH et succnacnacBnH (succ = succinimido) substitués par un groupement succinimido sur le carbone  La chloration par le N-chlorosuccinimide conduit au produit désiré, mais avec des impuretés. La réaction de ces ligands avec le CuOtBu (ou bien MesCu, où Mes = C6Me3H2, et une quantité catalytique de CuOtBu) en présence de bases de Lewis donne les (nacnacxylCu)2(-toluène), nacnacxylCuCNC6H3(Me)2, nacnacCH(Me)PhCuL (L = PPh3, PMe3, CNC6H3(Me)2, DMAP, lutidine, Py, MeCN), nacnacBnCuL (L = PPh3, CNC6H3(Me)2, styrène, trans-stilbene, phenylvinylether, acrylonitrile, diphenylacetylène), nacnaciPrCuL (L = PPh3, CNC6H3(Me)2, MeCN) et le succnacnacCH(Me)PhCuL (PPh3, CNC6H3(Me)2, pyridine). Tous ces complexes sont jaunes et sensibles à l’air et à l’humidité. En l’absence de fortes bases de Lewis, on n’observe pas de réaction entre les précurseurs de cuivre et les ligands N-alkyle substitués. Les études RMN des complexes dans le C6D6 ne présentent pas de complexe de toluène mais un mélange à l’équilibre du (nacnacxylCu)2(-C6D6) et nacnacxylCu(C6D6) dans une proportion de 2 pour 1. Alors que l’addition de plus de cinquante équivalents soit de THF, soit de toluène n’induit aucun changement des spectres RMN, l’addition de 2 équivalents de MeCN conduit instantanément au complexe nacnacxylCu(MeCN). De plus, le (nacnacxylylCu)2(-C6D6) ne se coordone ni ne réagit avec le N2O, même après avoir été chauffé à 60°C pendant treize jours. En présence de DPA (diphenylacétylène), la réaction du nacnacBnH avec le CuOtBu conduit au dimère ponté (nacnacBnCu)2(µ-DPA). L’addition d’un excès de DPA (10-12 équivalents) transforme le dimère ponté en complexe lié en position terminale nacnacBnCuDPA. Les nacnacRH (R = CH(Me)Ph et i-Pr) ne forment pas de complexe ni avec les oléfines ni avec le DPA. Une réactivité similaire a été observée avec les complexes de nacnacCH(Me)PhCu(NCMe) et nacnaci-PrCu(NCMe). Tandis que le complexe lié en position terminale par MeCN a été isolé et caractérisé, l’équilibre en solution nous laisse suspecter la formation d’un complexe d’acétonitrile ponté. Des études de réactivité comparatives ont été menées sur quelques complexes de cuivre. La Morpholine ne réagit pas avec le nacnacBnCu(acrylonitrile) contrairement à l’acrylonitrile libre. L’expérience de l’échange d’oléfine montre que l’acrylonitrile (une oléfine électro-attractrice) se lie plus fortement que les autres oléfines, mettant ainsi en évidence l’importance de la rétrodonation  face à la donation La rétrodonation est cependant faible comparée aux autres complexes de styrène structurellement caractérisés. Les complexes nacnacCH(Me)PhCuL (L = PPh3 et MeCN) ont été employés dans la cyclopropanation catalytique du styrène et dans l’addition conjuguée du ZnEt2 sur la 2-cyclohexénone, mais les résultats indiquent que le ligand dikétimine est éliminé avant son entrée dans le cycle catalytique. Par conséquent, il n’y a pas d’induction chirale. Les complexes tétra coordinées de cuivre avec les nacnacRCu(phen) (R = Bn, CH(Me)Ph et Phen = 1,10-phenanthroline, 2-Mes-1,10-phenanthroline, 2,9-dimethyl-1,10-phenanthroline (dmp) et 2,9-diphenyl-1,10-phenanthroline (dpp)) ont été synthétisés. Ces complexes sont d’une intense couleur bleue et des interactions d’empilement entre l’un des cycles phényle des ligands nacnac et la phénanthroline ont été observées dans les structures à l’état solide. Les mesures en absorption UV-visible ont été effectuées dans le toluène et les bandes MLCT sont déplacées vers le rouge par rapport à celles des complexes de cuivre et bisphénanthroline. Tous ces composés émettent à l’état solide mais les complexes 1,10-phenanthroline et 2-Mes-1,10-phenanthroline n’émettent pas en solution. Pour renforcer les interactions d’empilement , les nouveaux ligands nacnacRH (R = CH2C6H2(OMe)3, CH2C6F5) et leurs complexes de cuivre respectifs ont été préparés avec du dmp et dpp. Afin de permettre la comparaison, le nacnaciBuCu(dmp) a été synthétisé. Alors que les complexes dmp montrent une augmentation des interactions intramoléculaires - avec les substituants phényle du ligand dikétimine et de la phénanthroline, les complexes dpp ne révèlent pas de telles interactions. Les complexes perfluorés montrent, en absorption et en émission, un déplacement significatif vers le bleu, alors que les complexes substitués par un groupements isobutyle présentent des transitions déplacées vers le rouge. Alors que les intensités de luminescence et les durées de vie sont faibles, les déplacements réduits de Stokes et les pics étroits de luminescence comparables indiquent une réduction des distorsions de l’état excité.

Évaluation de nouveaux électrolytes à base de liquides ioniques protiques en supercapacités asymétriques de type MnO2/carbone

Les supercapacités hybrides se taillent de plus en plus une place dans le secteur des énergies renouvelables. L’oxyde de manganèse possède certaines caractéristiques (faible coût, caractère écologique et une capacitance spécifique supérieure) qui font de ce dernier un matériau très attirant pour l’assemblage de tels dispositifs. Ce mémoire, divisé en trois parties, propose l’utilisation des liquides ioniques protiques comme électrolytes pour l’assemblage de supercapacités hybrides à base d’oxyde de manganèse et carbone. D’abord, le comportement pseudocapacitif des électrodes à base de films minces d’oxyde de manganèse dans les liquides ioniques protiques ainsi que leurs propriétés optiques sont étudiés et évalués. Des valeurs de capacitance spécifique allant jusqu’à 397 F/g ont été trouvées dans cette partie. Ensuite, des mélanges composés par un solvant organique (acétonitrile) et le liquide ionique protique sont présentés comme une manière de contourner la faible conductivité de ce dernier qui limite les valeurs de capacitance spécifique à obtenir. Une amélioration de la capacitance spécifique d’environ 30% est reportée dans ce chapitre. Finalement, l’assemblage d’une supercapacité hybride est présenté comme une stratégie efficace qui permet l’élargissement de la faible fenêtre de potentiel de travail obtenue avec les électrodes à base d’oxyde de manganèse. De cette façon, la faisabilité de tel arrangement est montré ici, obtenant de valeurs de capacitance spécifique (16 F/g) ainsi que de puissance (81 W/kg) et d’énergie spécifique (1,9 Wh/kg) acceptables en utilisant des liquides ioniques protiques comme électrolytes de remplissage.

Novel M(II) beta-diketiminate complexes for the polymerization of lactide

Des ligands diketimines porteurs de substituants N-benzyl, N-9-anthrylmethyl et N-mesitylmethyl (nacnacBnH, nacnacAnH, and nacnacMesH) ont été synthétisés par condensation d’une amine et d’acétyl acétone ou son monoacétal d’éthylène glycol. La chlorination de la position 3 a été effectuée à l’aide de N-chlorosuccinimide conduisant à la formation des ligands ClnacnacBnH et ClnacnacAnH. Cette même position 3 a également été substituée par un groupement succinimide par lithiation du nacnacBnH, suivi de la réaction avec le N-chlorosuccinimide (3-succinimido-nacnacBnH). Les ligands N-aryl nacnacippH et nacnacNaphH (ipp = 2-isopropylphenyl, Naph = 1-naphthyl) ont été préparés selon les procédures reportées dans la littérature. La réaction de ces ligands avec Zn(TMSA)2 (TMSA = N(SiMe3)2) conduit à la formation des complexes nacnacAnZn(TMSA) et ClnacnacBnZn(TMSA). La protonation avec l’isopropanol permet l’obtention des complexes nacnacAnZnOiPr et ClnacnacBnZnOiPr. La réaction avec Mg(TMSA)2 permet quant à elle la formation des complexes nacnacAnMg(TMSA), nacnacMesMg(TMSA), ClnacnacBnMg(TMSA) et ClnacnacAnMg(TMSA). La protonation subséquente à l’aide du tert-butanol permet l’obtention du nacnacMesMgOtBu et du ClnacnacBnMgOtBu, alors que l’on observe uniquement une décomposition avec les ligands possédant des substituants N-anthrylmethyl. La réaction de ces diketimines avec Cu(OiPr)2 conduit aux dimères hétéroleptiques [nacnacBnCu(μ-OiPr)]2 et [3-Cl-nacnacBnCu(μ-OiPr)]2 lors de l’usage des ligands stériquement peu encombrés. Lors de l’utilisation de ligands plus encombrés, la stabilisation du complexe hétéroleptique par dimérisation n’est plus possible, conduisant, par un échange de ligand, à la formation des complexes homoleptiques Cu(nacnacipp)2 et Cu(nacnacNaph)2. Les complexes homoleptiques Cu(nacnacBn)2 et Cu(3-succinimido-nacnacBn)2 ont été obtenus à partir des ligands N-benzyl. Les ligands encore plus encombrés tels que nacnacAnH, nacnacMesH ou ceux comportant des substituants N-methylbenzyl ne présentent alors plus de réactivité avec le Cu(OiPr)2. La plupart des complexes ont été caractérisés par Diffraction des Rayons X. Les complexes homoleptiques ainsi que ceux de TMSA sont monomériques, alors que ceux formés à partir d’alkoxides se présentent sous forme de dimères à l’état solide. Tous les complexes d’alkoxides ainsi que les nacnacAnMg(TMSA)/BnOH et ClnacnacAnMg(TMSA)/BnOH présentent une réactivité modérée à haute en matière de polymérisation du rac-lactide (90% de conversion en 30 secondes à 3 heures). Le nacnacAnZnOiPr permet la synthèse d’un polymère hautement hétérotactique (Pr = 0.90) quand le ClnacnacBnMgOtBu/BnOH génère un polymère isotactique à -30°C (Pr = 0.43). Tous les autres catalyseurs produisent des polymères atactiques avec une légère tendance hétérotactique (Pr = 0.48 – 0.55). Les complexes hétéroleptiques [nacnacBnCu(μ-OiPr)]2 et [3-Cl-nacnacBnCu(μ-OiPr)]2 se révèlent être de très bons catalyseurs pour la polymérisation du rac-lactide présentant une conversion complète du monomère à température ambiante, en solution, en 0,5 à 5 minutes. Le [nacnacBnCu(μ-OiPr)]2 est actif en présence ou absence d’isopropanol, agissant comme agent de transfert de chaine à haute activité (k2 = 32 M–1•s–1) dans le dichlorométhane. Dans l’acétonitrile, le THF, le dichloromethane et le toluène, [nacnacBnCu(μ-OiPr)]2 conduit à une étroite polydispersité, possédant respectivement des kobs = 2.4(1), 5.3(5), 3.6-4.4 and 10(1) min–1. Aucune réaction parasite, telle qu’une trans-esterification, une épimerisation ou une décomposition du catalyseur, n’a été observée. Les complexes homoleptiques en présence d’alcool libre semblent présenter un équilibre avec une petite quantité de leurs équivalents hétéroleptiques, permettant une polymérisation complète, en moins de 60 min, à température ambiante. Tous les catalyseurs de cuivre présentent un haut contrôle de la polymérisation avec une polydispersité égale ou inférieure à 1.1. Les polymères obtenus sont essentiellement atactiques, avec une légère tendance à l’hétérotacticité à température ambiante et -17°C. Le [nacnacBnCu(μ-OiPr)]2 polymérise également la -butyrolactone (BL), l’-caprolactone (CL) et la -valerolactone (VL) avec des constantes respectivement égales à kobs = 3.0(1)•10–2, 1.2–2.7•10–2, et 0.11(1) min–1. Les homopolymères présentent une étroite polydispersité d’approximativement 1.1. Les polymérisations par addition séquentielle ont mis en évidence une trans-estérification (non observée dans les homopolymérisations) si BL ou CL sont introduits après un bloc lactide.