Authentication of vegetable oils by bulk and molecular carbon isotope analyses with emphasis on olive oil and pumpkin seed oil

The authenticity of vegetable oils consumed in Slovenia and Croatia was investigated by carbon isotope analysis of the individual fatty acids by the use of gas chromatography-combustion-isotope ratio mass spectrometry (GC/C/IRMS), and through carbon isotope analysis of the bulk oil. The fatty acids from samples of olive, pumpkin, sunflower, maize, rape, soybean, and sesame oils were separated by alkaline hydrolysis and derivatized to methyl esters for chemical characterization by capillary gas chromatography/mass spectrometry (GC/MS) prior to isotopic analysis. Enrichment in heavy carbon isotope (C-13) of th, bulk oil and of the individual fatty acids are related to (1) a thermally induced degradation during processing (deodorization, steam washing, or bleaching), (2) hydrolytic rancidity (lipolysis) and oxidative rancidity of the vegetable oils during storage, and (3) the potential blend with refined oil or other vegetable oils. The impurity or admixture of different oils may be assessed from the delta C-13(16:0) VS. delta C-13(18:1) covariations. The fatty acid compositions of Slovenian and Croatian olive oils are compared with those from the most important Mediterranean producer countries (Spain, Italy, Greece, and France).

Field Testing of Integral Abutments, Interim Report, HR-399, 1998

Integral abutment bridges are constructed without an expansion joint in the superstructure of the bridge; therefore, the bridge girders, deck, abutment diaphragms, and abutments are monolithically constructed. The abutment piles in an integral abutment bridge are vertically orientated, and they are embedded into the pile cap. When this type of a bridge experiences thermal expansion or contraction, horizontal displacements are induced at the top of the abutment piles. The flexibility of the abutment piles eliminates the need to provide an expansion joint at the inside face to the abutments: Integral abutment bridge construction has been used in Iowa and other states for many years. This research is evaluating the performance of integral abutment bridges by investigating thermally induced displacements, strains, and temperatures in two Iowa bridges. Each bridge has a skewed alignment, contains five prestressed concrete girders that support a 30-ft wide roadway for three spans, and involves a water crossing. The bridges will be monitored for about two years. For each bridge, an instrumentation package includes measurement devices and hardware and software support systems. The measurement devices are displacement transducers, strain gages, and thermocouples. The hardware and software systems include a data-logger; multiplexers; directline telephone service and computer terminal modem; direct-line electrical power; lap-top computer; and an assortment of computer programs for monitoring, transmitting, and management of the data. Instrumentation has been installed on a bridge located in Guthrie County, and similar instrumentation is currently being installed on a bridge located in Story County. Preliminary test results for the bridge located in Guthrie County have revealed that temperature changes of the bridge deck and girders induce both longitudinal and transverse displacements of the abutments and significant flexural strains in the abutment piles. For an average temperature range of 73° F for the superstructure concrete in the bridge located in Guthrie County, the change in the bridge length was about 1 118 in. and the maximum, strong-axis, flexural-strain range for one of the abutment piles was about 400 micro-strains, which corresponds to a stress range of about 11,600 psi.

Computational Approach to the Study of Thermal Spin Crossover Phenomena

The key parameters associated to the thermally induced spin crossover process have been calculated for a series of Fe(II) complexes with mono-, bi-, and tridentate ligands. Combination of density functional theory calculations for the geometries and for normal vibrational modes, and highly correlated wave function methods for the energies, allows us to accurately compute the entropy variation associated to the spin transition and the zero-point corrected energy difference between the low- and high-spin states. From these values, the transition temperature, T 1/2, is estimated for different compounds.

Laimentimen merkitys metallien neste-nesteuutossa

Työssä tutkittiin korkean leimahduspisteen laimentimien vaikutusta uuton tehokkuuteen ja turvallisuuteen. Kirjallisuusosa sisältää katsauksen uuttolaitoksilla tapahtuneista suuronnettomuuksista, staattisen sähkön aiheuttamista vaaroista uuttolaitoksilla ja kaupallisesti saatavista laimentimista. Lisäksi kirjallisuusosassa tarkastellaan hiilivetyjen molekyylirakenteen vaikutusta niiden leimahduspisteeseen, haihtuvuuteen, viskositeettiin ja liuotinominaisuuksiin. Kokeellisessa osassa tutkittiin uuton tehokkuutta kuvaavia ominaisuuksia, joita olivat sekoituksen pisarakoko, faasien selkeytymisnopeus,uuton ja takaisinuuton kinetiikka, orgaanisen faasin viskositeetti ja tiheys. Uuttoliuosten turvallisuusominaisuuksia tutkittiin mittaamalla synteettisten uuttoliuosten ja laimentimien leimahduspisteitä sekä sähköisesti varattujen laimentimien relaksaatioaikoja. Korkean leimahduspisteen laimentimena käytettiin Orfom SX 11-laimenninta. Vertailukohteena käytettiin Shellsol D70- ja Escaid 100- laimentimia. Malliuuttona käytettiin kuparin uuttoa hydroksioksiimireagensilla happamasta sulfaattiliuoksesta. Kokeissa havaittiin, että korkean leimahduspisteen laimentimen viskositeetti oli huomattavasti suurempi kuin Shellsol D70- laimentimella. Korkea viskositeetti hidasti faasien selkeytymistä uutossa, mutta sillä ei ollut vaikutusta uuton kinetiikkaan tai sekoituksen aiheuttamaan pisarakokoon. Uuttoliuoksen reagenssipitoisuudella havaittiin olevan vaikutusta uuttoliuoksen leimahduspisteeseen, mutta uuttoliuoksen latausasteella ei havaittu olevan vaikutusta. Sähköisesti varattujen laimentimien varauksien relaksaatioajoissa oli hieman eroja, mutta relaksaatioajat olivat kaikilla laimentimilla liian pitkiä staattisen sähkön aiheuttaman vaaran poistamiseksi.

Validation Studies of Thermal-hydraulic Code for Safety Analysis of Nuclear Power Plants

This thesis gives an overview of the validation process for thermal hydraulic system codes and it presents in more detail the assessment and validation of the French code CATHARE for VVER calculations. Three assessment cases are presented: loop seal clearing, core reflooding and flow in a horizontal steam generator. The experience gained during these assessment and validation calculations has been used to analyze the behavior of the horizontal steam generator and the natural circulation in the geometry of the Loviisa nuclear power plant. The cases presented are not exhaustive, but they give a good overview of the work performed by the personnel of Lappeenranta University of Technology (LUT). Large part of the work has been performed in co-operation with the CATHARE-team in Grenoble, France. The design of a Russian type pressurized water reactor, VVER, differs from that of a Western-type PWR. Most of thermal-hydraulic system codes are validated only for the Western-type PWRs. Thus, the codes should be assessed and validated also for VVER design in order to establish any weaknesses in the models. This information is needed before codes can be used for the safety analysis. Theresults of the assessment and validation calculations presented here show that the CATHARE code can be used also for the thermal-hydraulic safety studies for VVER type plants. However, some areas have been indicated which need to be reassessed after further experimental data become available. These areas are mostly connected to the horizontal stem generators, like condensation and phase separation in primary side tubes. The work presented in this thesis covers a large numberof the phenomena included in the CSNI code validation matrices for small and intermediate leaks and for transients. Also some of the phenomena included in the matrix for large break LOCAs are covered. The matrices for code validation for VVER applications should be used when future experimental programs are planned for code validation.

Epäpuhtaudet sinkin uutossa

Työssä tutkittiin metalli- ja anioniepäpuhtauksien myötäuuttautumista sinkin mukana di(2-etyyliheksyyli)fosforihappoalla (D2EHPA). Laboratoriokokeissa selvitettiin pH:n vaikutusta metalliepäpuhtauksien uuttautumiseen pH-alueella -O, l... 3 sekä pesujen vaikutusta sinkillä ladatun orgaanisen faasin metallipitoisuuksiin. Kokeita tehtiin sekä synteettisillä että autenttisilla prosessiliuoksilla. Anionikokeissa tutkittiin raudan ja sinkin vaikutusta kloridin ja fluoridin uuttautumiseen. Synteettisillä liuoksilla tehdyissä kokeissa tutkittiin kadmiumin, koboltin, nikkelin, kuparin sekä antimonin uuttautumista sinkkisulfaattiliuoksesta. Kokeissa havaittiin D2EHPA:n uuttavan sinkkiä selvästi em. metalleja paremmin. Sinkki uuttautui sulfaattiliuoksesta lähes täydellisesti tasapaino-pH:n ollessa yli 2,3. Sinkin jälkeen muista metalleista uuttautui eniten kadmium ja järjestyksessä sitten kupari, koboltti ja nikkeli. Epäpuhtausmetallien myötäuuttautumista lisääntyi uuton tasapaino-pH:n kasvaessa ja väheni sinkkilatauksen kasvaessa. Kahdella peräkkäisellä pesuaskeleella, joissa ensimmäinen pesuliuos sisälsi 5 g/L rikkihappoa ja toinen sekä 15 g/L rikkihappoa että 5 g/L sinkkiä saatiin kaikkien epäpuhtausmetallien pitoisuudet jäämään alle 3 mg/L. Antimonin uuttokokeissa huomattiin antimonin uuttautuvan täydellisesti D2EHPA:lla pH:sta riippumatta pH-alueella0...3. Prosessiliuoksilla tehdyissä kokeissa todettiin D2EHPA:n pystyvän tehokkaasti erottamaan sinkin magnesiumista ßzn,Mg ˜107 ja kadmiumista ßzn,cd ˜106. Havaittiin myös, että mitä suurempi sinkki- ja rautalataus orgaanisessa faasissa on sitä vähemmän magnesiumia ja kadmiumia uuttautuu. Ensimmäisessä pesussa saatiin sekä kadmiumin että magnesiumin pitoisuudet putoamaan keskimäärin 0,1 mg/L eli 30 alkuperäisestä pitoisuudesta. Toisella pesuaskeleella ei enää ollut vaikutusta kadmiumin ja magnesiumin pitoisuuksiin orgaanisessa faasissa. Kokeissa havaittiin myös, että D2EHPA:n latausasteen ylittäessä 0,7 alkaa sinkki-D2EHPA-kompleksit polymeroitua ja faasit eivät enää selkeytyneet helposti. Anionikokeissa huomattiin, ettei D2EHPA uuttanut kloridi tai fluoridi sinkin tai raudan mukana. D2EHPA:n havaittiin myös itsessään sisältävän hieman kloridia.

Single acquisition electrical property mapping based on relative coil sensitivities: A proof-of-concept demonstration.

PURPOSE: All methods presented to date to map both conductivity and permittivity rely on multiple acquisitions to compute quantitatively the magnitude of radiofrequency transmit fields, B1+. In this work, we propose a method to compute both conductivity and permittivity based solely on relative receive coil sensitivities ( B1-) that can be obtained in one single measurement without the need to neither explicitly perform transmit/receive phase separation nor make assumptions regarding those phases. THEORY AND METHODS: To demonstrate the validity and the noise sensitivity of our method we used electromagnetic finite differences simulations of a 16-channel transceiver array. To experimentally validate our methodology at 7 Tesla, multi compartment phantom data was acquired using a standard 32-channel receive coil system and two-dimensional (2D) and 3D gradient echo acquisition. The reconstructed electric properties were correlated to those measured using dielectric probes. RESULTS: The method was demonstrated both in simulations and in phantom data with correlations to both the modeled and bench measurements being close to identity. The noise properties were modeled and understood. CONCLUSION: The proposed methodology allows to quantitatively determine the electrical properties of a sample using any MR contrast, with the only constraint being the need to have 4 or more receive coils and high SNR. Magn Reson Med, 2014. © 2014 Wiley Periodicals, Inc.

Nikkelin takaisinuutto karboksyylihappoon perustuvasta uuttoreagenssista

Työssä tutkittiin typpihapon soveltuvuutta nikkelin takaisinuuttoon. Tarkoituksena oli selvittää, millä typpihapon konsentraatioilla orgaaninen faasi, joka koostuu Versatic 10 uuttoreagenssista ja alifaattisesta laimentimesta, alkaa nitrautua tai hapettua ja mitkä ovat mahdolliset sivureaktiot. Lisäksi tutkittiin rikkihapon ja eräiden orgaanisten aineiden kontaminaation vaikutusta uuttoliuokseen. Kirjallisuusosassa kartoitetaan mahdollisten nitrautumisreaktioiden mekanismit, sekä kuvataan laimentimen, uuttoreagenssin ja mahdollisten reaktiotuotteiden ominaisuuksia, sekä niiden mahdollisessa muodostumisessa syntyviä riskejä. Orgaanisen faasin kestotesteissä tutkittavia muuttujia olivat typpi- ja rikkihapon konsentraatio, sekoitusaika, lämpötila, avoin tai suljettu astia sekä vieraiden aineiden kontaminaatio. Kontaminaatiota aiheuttavien orgaanisten materiaalien funktionaaliset ryhmät olivat hydroksi-, karbonyyli- ja amiiniryhmät, joiden lisäksi tutkittiin syklisen yhdisteen kontaminaatiota. Analyyseissä käytettiin FT-IR- spektroskopiaa, jolla tutkittiin reagenssin funktionaalisen ryhmän reaktioita ja uusien ryhmien muodostumista, sekä seurattiin selkeytyksessä erottumattomien typpiyhdisteiden määrää ja laatua orgaanisessa faasissa. Uuttofaasin koostumuksen muutosta seurattiin myös mittaamalla leimahduspisteen muutosta.

Tailoring the surface density of silicon nanocrystals embedded in SiOx single layers

In this article, we explore the possibility of modifying the silicon nanocrystal areal density in SiOx single layers, while keeping constant their size. For this purpose, a set of SiOx monolayers with controlled thickness between two thick SiO2 layers has been fabricated, for four different compositions (x=1, 1.25, 1.5, or 1.75). The structural properties of the SiO x single layers have been analyzed by transmission electron microscopy (TEM) in planar view geometry. Energy-filtered TEM images revealed an almost constant Si-cluster size and a slight increase in the cluster areal density as the silicon content increases in the layers, while high resolution TEM images show that the size of the Si crystalline precipitates largely decreases as the SiO x stoichiometry approaches that of SiO2. The crystalline fraction was evaluated by combining the results from both techniques, finding a crystallinity reduction from 75% to 40%, for x = 1 and 1.75, respectively. Complementary photoluminescence measurements corroborate the precipitation of Si-nanocrystals with excellent emission properties for layers with the largest amount of excess silicon. The integrated emission from the nanoaggregates perfectly scales with their crystalline state, with no detectable emission for crystalline fractions below 40%. The combination of the structural and luminescence observations suggests that small Si precipitates are submitted to a higher compressive local stress applied by the SiO2 matrix that could inhibit the phase separation and, in turn, promotes the creation of nonradiative paths.

Process intensification: From optimised flow patterns to microprocess technology

This thesis is focused on process intensification. Several significant problems and applications of this theme are covered. Process intensification is nowadays one of the most popular trends in chemical engineering and attempts have been made to develop a general, systematic methodology for intensification. This seems, however, to be very difficult, because intensified processes are often based on creativity and novel ideas. Monolith reactors and microreactors are successful examples of process intensification. They are usually multichannel devices in which a proper feed technique is important for creating even fluid distribution into the channels. Two different feed techniques were tested for monoliths. In the first technique a shower method was implemented by means of perforated plates. The second technique was a dispersion method using static mixers. Both techniques offered stable operation and uniform fluid distribution. The dispersion method enabled a wider operational range in terms of liquid superficial velocity. Using dispersion method, a volumetric gas-liquid mass transfer coefficient of 2 s-1 was reached. Flow patterns play a significant role in terms of the mixing performance of micromixers. Although the geometry of a T-mixer is simple, channel configurations and dimensions had a clear effect on mixing efficiency. The flow in the microchannel was laminar, but the formation of vortices promoted mixing in micro T-mixers. The generation of vortices was dependent on the channel dimensions, configurations and flow rate. Microreactors offer a high ratio of surface area to volume. Surface forces and interactions between fluids and surfaces are, therefore, often dominant factors. In certain cases, the interactions can be effectively utilised. Different wetting properties of solid materials (PTFE and stainless steel) were applied in the separation of immiscible liquid phases. A micro-scale plate coalescer with hydrophilic and hydrophobic surfaces was used for the continuous separation of organic and aqueous phases. Complete phase separation occurred in less than 20 seconds, whereas the separation time by settling exceeded 30 min. Fluid flows can be also intensified in suitable conditions. By adding certain additives into turbulent fluid flow, it was possible to reduce friction (drag) by 40 %. Drag reduction decreases frictional pressure drop in pipelines which leads to remarkable energy savings and decreases the size or number of pumping facilities required, e.g., in oil transport pipes. Process intensification enables operation often under more optimal conditions. The consequent cost savings from reduced use of raw materials and reduced waste lead to greater economic benefits in processing.

Síntese de biodiesel: uma proposta contextualizada de experimento para laboratório de química geral

The contextualized understanding of concepts in Chemistry by students from other areas is a challenging task. In this experiment, the synthesis of biodiesel is done by base catalyzed transesterification of refined soy oil with methanol at room temperature and common glassware found in any chemistry laboratory. The proposal permits introducing several concepts, such as that of emulsion, viscosity and catalysis to illustrate an activity based on an actual problem. In this didactic approach, some common problems of biodiesel production, such as soap formation and phase separation, are introduced into the procedure in order to raise questions and motivate the students to participate in the experimental work and stimulate reflections about critical aspects of biodiesel production. This experiment was carried out in the first semester of 2006, in experimental general chemistry taken by physics and agricultural, civil and chemical engineering students of UNICAMP.

Estudo por espectroscopia micro-Raman dos mecanismos de separação de fase em vidros fosfatos de metais de transição

Glass-ceramics are prepared by controlled separation of crystal phases in glasses, leading to uniform and dense grain structures. On the other hand, chemical leaching of soluble crystal phases yields porous glass-ceramics with important applications. Here, glass/ceramic interfaces of niobo-, vanado- and titano-phosphate glasses were studied by micro-Raman spectroscopy, whose spatial resolution revealed the multiphase structures. Phase-separation mechanisms were also determined by this technique, revealing that interface composition remained unchanged as the crystallization front advanced for niobo- and vanadophosphate glasses (interface-controlled crystallization). For titanophosphate glasses, phase composition changed continuously with time up to the equilibrium composition, indicating a spinodal-type phase separation.

Avaliação da biodegradabilidade de efluentes têxteis do beneficiamento secundário de malhas de poliéster tratados com Reagente de Fenton

From the environmental point of view, the textile sector is outstanding for the generation of large amounts of biorecalcitrant effluents. In this paper the textile effluent biodegradability, both before and after its treatment with Fenton's Reagent, were compared by means of biologic tests. These tests showed that the Fenton treatment lowered the biodegradabilty of practically all tested effluents, except one specific effluent from a scouring bath of polyester fibers, which achieved a 93% COD removal. This removal was due to a significant phase separation (oil/water).

Determinação do ponto de névoa em surfactantes não iônicos por espectroscopia de impedância elétrica

In this paper, we analyze the use of electrical impedance spectroscopy applied to determination of cloud point. The slope of admittance measured at 100 kHz is reduced to temperature above the critical value which characterizes the phase transition, in a strong indication that this process is activated during the clouding. Additionally to this study we explored the influence of parameters such as additives and temperature on the performance of phase separation of residues (silver nanoparticles) by cloud point extraction. The interaction with salt maximizes the separation of chemical residues in a progressively reduced temperature.

A reliable method of quantification of trace copper in beverages with and without alcohol by spectrophotometry after cloud point extraction

A new cloud point extraction (CPE) method was developed for the separation and preconcentration of copper (II) prior to spectrophotometric analysis. For this purpose, 1-(2,4-dimethylphenyl) azonapthalen-2-ol (Sudan II) was used as a chelating agent and the solution pH was adjusted to 10.0 with borate buffer. Polyethylene glycol tert-octylphenyl ether (Triton X-114) was used as an extracting agent in the presence of sodium dodecylsulphate (SDS). After phase separation, based on the cloud point of the mixture, the surfactant-rich phase was diluted with acetone, and the enriched analyte was spectrophotometrically determined at 537 nm. The variables affecting CPE efficiency were optimized. The calibration curve was linear within the range 0.285-20 µg L-1 with a detection limit of 0.085 µg L-1. The method was successfully applied to the quantification of copper in different beverage samples.