Turbulent velocity and suspended sediment concentration measurements in an urban environment of the Brisbane River Flood Plain at Gardens Point on 12-13 January 2011

The flood flow in urbanised areas constitutes a major hazard to the population and infrastructure as seen during the summer 2010-2011 floods in Queensland (Australia). Flood flows in urban environments have been studied relatively recently, although no study considered the impact of turbulence in the flow. During the 12-13 January 2011 flood of the Brisbane River, some turbulence measurements were conducted in an inundated urban environment in Gardens Point Road next to Brisbane's central business district (CBD) at relatively high frequency (50 Hz). The properties of the sediment flood deposits were characterised and the acoustic Doppler velocimeter unit was calibrated to obtain both instantaneous velocity components and suspended sediment concentration in the same sampling volume with the same temporal resolution. While the flow motion in Gardens Point Road was subcritical, the water elevations and velocities fluctuated with a distinctive period between 50 and 80 s. The low frequency fluctuations were linked with some local topographic effects: i.e, some local choke induced by an upstream constriction between stairwells caused some slow oscillations with a period close to the natural sloshing period of the car park. The instantaneous velocity data were analysed using a triple decomposition, and the same triple decomposition was applied to the water depth, velocity flux, suspended sediment concentration and suspended sediment flux data. The velocity fluctuation data showed a large energy component in the slow fluctuation range. For the first two tests at z = 0.35 m, the turbulence data suggested some isotropy. At z = 0.083 m, on the other hand, the findings indicated some flow anisotropy. The suspended sediment concentration (SSC) data presented a general trend with increasing SSC for decreasing water depth. During a test (T4), some long -period oscillations were observed with a period about 18 minutes. The cause of these oscillations remains unknown to the authors. The last test (T5) took place in very shallow waters and high suspended sediment concentrations. It is suggested that the flow in the car park was disconnected from the main channel. Overall the flow conditions at the sampling sites corresponded to a specific momentum between 0.2 to 0.4 m2 which would be near the upper end of the scale for safe evacuation of individuals in flooded areas. But the authors do not believe the evacuation of individuals in Gardens Point Road would have been safe because of the intense water surges and flow turbulence. More generally any criterion for safe evacuation solely based upon the flow velocity, water depth or specific momentum cannot account for the hazards caused by the flow turbulence, water depth fluctuations and water surges.

Navigating, recognizing and describing urban spaces with vision and lasers

In this paper we describe a body of work aimed at extending the reach of mobile navigation and mapping. We describe how running topological and metric mapping and pose estimation processes concurrently, using vision and laser ranging, has produced a full six-degree-of-freedom outdoor navigation system. It is capable of producing intricate three-dimensional maps over many kilometers and in real time. We consider issues concerning the intrinsic quality of the built maps and describe our progress towards adding semantic labels to maps via scene de-construction and labeling. We show how our choices of representation, inference methods and use of both topological and metric techniques naturally allow us to fuse maps built from multiple sessions with no need for manual frame alignment or data association.

Meaningful engagement with music composition

Musical value cannot be experienced without direct knowledge of music, and engagement with the interactive elements of materials, expressive character and structure. Through these channels something is communicated, something is transmitted, some residue of ‘meaning’ is left with us. When a work of art stirs us it is more than simply sensory stimulation or some kind of emotional indulgence. We are gaining knowledge and expanding our experience... contributing to knowledge of ourselves and of the world.

Artful interviewing: Conducting oral history interviews for practice-led research

Recently, there has been an increased use of oral history as source material and inspiration for creative products, such as new media productions; visual art; theatre and fiction. The rise of the digital story in museum and library settings reflects a new emphasis on publishing oral histories in forms that are accessible and speak to diverse audiences. Visual artists are embracing oral history as a source of emotional, experiential and thematic authenticity (Anderson 2009 and Brown 2009). Rosemary Neill (2010) observes the rise of documentary and verbatim theatre — where the words of real people are reproduced on-stage — in Australia. Authors such as Dave Eggers (2006), M. J. Hyland (2009), Padma Viswanathan (2008) and Terry Whitebeach (2002) all acknowledge that interviews heavily inform their works of fiction. In such contexts, oral histories are not valued so much for their factual content but as sources that are at once dynamic, evolving, emotionally authentic and ambiguous. How can practice-led researchers design interviews that reflect this emphasis? In this paper, I will discuss how I developed an interview methodology for my own practice-led research project, The Artful Life Story: Oral History and Fiction. In my practice, I draw on oral histories to inform a work of fiction. I developed a methodology for eliciting sensory details and stories around place and the urban environment. I will also read an extract from ‘Evelyn on the Verandah,’ a short story based on an oral history interview with a 21 year-old woman who grew up in New Farm, which will be published in the One Book Many Brisbanes short story anthology in June this year (2010).

Consumer product-related injuries in Queensland children : A snapshot of current problem areas for potential action

This report presents a snapshot from work which was funded by the Queensland Injury Prevention Council in 2010-11 titled “Feasibility of Using Health Data Sources to Inform Product Safety Surveillance in Queensland children”. The project provided an evaluation of the current available evidence-base for identification and surveillance of product-related injuries in children in Queensland and Australia. A comprehensive 300 page report was produced (available at: http://eprints.qut.edu.au/46518/) and a series of recommendations were made which proposed: improvements in the product safety data system, increased utilisation of health data for proactive and reactive surveillance, enhanced collaboration between the health sector and the product safety sector, and improved ability of health data to meet the needs of product safety surveillance. At the conclusion of the project, a Consumer Product Injury Research Advisory group (CPIRAG) was established as a working party to the Queensland Injury Prevention Council (QIPC), to prioritise and advance these recommendations and to work collaboratively with key stakeholders to promote the role of injury data to support product safety policy decisions at the Queensland and national level. This group continues to meet monthly and is comprised of the organisations represented on the second page of this report. One of the key priorities of the CPIRAG group for 2012 was to produce a snapshot report to highlight problem areas for potential action arising out of the larger report. Subsequent funding to write this snapshot report was provided by the Institute for Health and Biomedical Innovation, Injury Prevention and Rehabilitation Domain at QUT in 2012. This work was undertaken by Dr Kirsten McKenzie and researchers from QUT's Centre for Accident Research and Road Safety - Queensland. This snapshot report provides an evidence base for potential further action on a range of children’s products that are significantly represented in injury data. Further information regarding injury hazards, safety advice and regulatory responses are available on the Office of Fair Trading (OFT) Queensland website and the Product Safety Australia websites. Links to these resources are provided for each product reviewed.

Genome-wide search for markers associated with bovine spongiform encephalopathy

A genome-wide search for markers associated with BSE incidence was performed by using Transmission-Disequilibrium Tests (TDTs). Significant segregation distortion, i.e., unequal transmission probabilities of alleles within a locus, was found for three marker loci on Chromosomes (Chrs) 5, 10, and 20. Although TDTs are robust to false associations owing to hidden population substructures, it cannot distinguish segregation distortion caused by a true association between a marker and bovine spongiform encephalopathy (BSE) from a population-wide distortion. An interaction test and a segregation distortion analysis in half-sib controls were used to disentangle these two alternative hypotheses. None of the markers showed any significant interaction between allele transmission rates and disease status, and only the marker on Chr 10 showed a significant segregation distortion in control individuals. Nevertheless, the control group may have been a mixture of resistant and susceptible but unchallenged individuals. When new genotypes were generated in the vicinity of these three markers, evidence for an association with BSE was confirmed for the locus on Chr 5.

Swimmer localization from a moving camera

At the highest level of competitive sport, nearly all performances of athletes (both training and competitive) are chronicled using video. Video is then often viewed by expert coaches/analysts who then manually label important performance indicators to gauge performance. Stroke-rate and pacing are important performance measures in swimming, and these are previously digitised manually by a human. This is problematic as annotating large volumes of video can be costly, and time-consuming. Further, since it is difficult to accurately estimate the position of the swimmer at each frame, measures such as stroke rate are generally aggregated over an entire swimming lap. Vision-based techniques which can automatically, objectively and reliably track the swimmer and their location can potentially solve these issues and allow for large-scale analysis of a swimmer across many videos. However, the aquatic environment is challenging due to fluctuations in scene from splashes, reflections and because swimmers are frequently submerged at different points in a race. In this paper, we temporally segment races into distinct and sequential states, and propose a multimodal approach which employs individual detectors tuned to each race state. Our approach allows the swimmer to be located and tracked smoothly in each frame despite a diverse range of constraints. We test our approach on a video dataset compiled at the 2012 Australian Short Course Swimming Championships.

Aha! The return of Alan Partridge

Throughout a long and occasionally distinguished career first as a television sports correspondent, then chat show host (dramatically ended by the accidental homicide of a guest live on air), then rebirth as a radio presenter at North Norfolk Digital, Alan Partridge has navigated the stormy waters of the British media landscape, now achieving mainstream success on the big screen with a starring role in Steve Coogan’s Alpha Papa (Declan Lowney, 2013). A man who in his desperation for a television series of his own once sank so low as to pitch a show called Monkey Tennis to the BBC finally finds his inner hero in a film which, while presenting mainly as comedy, also contains a biting critique of trends in the British media with which all journalists and media practitioners in general will be familiar. Alpha Papa is a nostalgic, elegiac riff on the pleasures and values of local radio the way it used to be, exemplified by North Norfolk Digital’s stable of flawed, but endearing jocks – Wally Banter, Bruno Brooks, Dave Clifton (who in one scene recounts the depths to which he sank as an alcoholic, drug addicted wreck—“I woke up in a skip with someone else’s underpants in my mouth. I can laugh about it now …”), and Pat Farrell. 50- something Pat is sacked by the new owners of North Norfolk Digital, who in their efforts to transform the station into a “multiplatform content provider” going by the more Gen Yfriendly name of Shape (“the way you want it to be”), wish to replace him with a younger, brattish model lacking in taste and manners. Out go records by the likes of Glen Campbell and Neil Diamond (“You can keep Jesus Christ”, observes Partridge after playing Diamond’s Sweet Caroline in a demonstration of the crackling radio repartee for which he is by now renowned, “that was the king of the Jews”), in comes Roachford. Pat, grieving his dead wife Molly, finally snaps and turns the glitzy media launch of Shape into a hostage siege. Only Alan Partridge, it seems, can step in and talk Pat out of a looming catastrophe.

Implementing lean in construction: Lean construction and BIM-CIRIA Guide C725

Building Information Modelling (BIM) and Lean construction have existed as two different initiatives to improve construction, with distinct communities and interests. In the last 10 years or so, both have started to diffuse into advanced practice, with accelerating speed. However, recently the insight has gained strength, first among pioneering practitioners and then among academics, that these two initiatives have a considerable mutual synergy and that it is highly advantageous to implement them jointly. In view of this, there are increasing needs to make BIM champions and users aware of Lean principles, methods and tools, as well as Lean champions and implementers aware of the functionalities of BIM. This guide is intended to provide a means to fulfill these needs.

Overview of building information modelling in healthcare projects

In this paper, we explore how BIM functionalities together with novel management concepts and methods have been utilized in thirteen hospital projects in the United States and the United Kingdom. Secondary data collection and analysis were used as the method. Initial findings indicate that the utilization of BIM enables a holistic view of project delivery and helps to integrate project parties into a collaborative process. The initiative to implement BIM must come from the top down to enable early involvement of all key stakeholders. It seems that it is rather resistance from people to adapt to the new way of working and thinking than immaturity of technology that hinders the utilization of BIM.

The Interaction of lean and building information modeling in construction

Lean construction and building information modeling (BIM) are quite different initiatives, but both are having profound impacts on the construction industry. A rigorous analysis of the myriad specific interactions between them indicates that a synergy exists which, if properly understood in theoretical terms, can be exploited to improve construction processes beyond the degree to which it might be improved by application of either of these paradigms independently. Using a matrix that juxtaposes BIM functionalities with prescriptive lean construction principles, 56 interactions have been identified, all but four of which represent constructive interaction. Although evidence for the majority of these has been found, the matrix is not considered complete but rather a framework for research to explore the degree of validity of the interactions. Construction executives, managers, designers, and developers of information technology systems for construction can also benefit from the framework as an aid to recognizing the potential synergies when planning their lean and BIM adoption strategies.

Lean construction, building information modelling and sustainability

This paper investigates the mutual relations of three current drivers of construction: lean construction, building information modelling and sustainability. These drivers are based on infrequently occurring changes, only incidentally simultaneous, in their respective domains. It is contended that the drivers are mutually supportive and thus synergistic. They are aligned in the sense that all require, promote or enable collaboration. It is argued that these three drivers should be implemented in a unified manner for rapid and robust improvements in construction industry performance and the quality of the constructed facilities and their benefits for stakeholders and wider society.

Analysis framework for the interaction between lean construction and building information modelling

Building with Building Information Modelling (BIM) changes design and production processes. But can BIM be used to support process changes designed according to lean production and lean construction principles? To begin to answer this question we provide a conceptual analysis of the interaction of lean construction and BIM for improving construction. This was investigated by compiling a detailed listing of lean construction principles and BIM functionalities which are relevant from this perspective. These were drawn from a detailed literature survey. A research framework for analysis of the interaction between lean and BIM was then compiled. The goal of the framework is to both guide and stimulate research; as such, the approach adopted up to this point is constructive. Ongoing research has identified 55 such interactions, the majority of which show positive synergy between the two.