Diode laser pumped, KERR phase-shifting and switching of a diode laser signal in a small area optical fibre

In this paper authors report the first demonstration of a diode laser powered Kerr effect device, consisting of a single birefringent fiber, able to phase-shift and switch an optical signal generated by a second laser diode. They have obtained fast, stable phase-shifting of 90° in a single fiber, at a coupled pump power of only 20 mW. Using this phase shift to induce polarization switching with resultant gating, 25% modulation of the diode laser signal has been observed, with a detection limited-rise time of 10ns.

An approach to determine the local boundary of small disturbance voltage stability region in a cut-set power space:基于微扰的割集电压稳定域局部边界求解方法

A new approach to determine the local boundary of voltage stability region in a cut-set power space (CVSR) is presented. Power flow tracing is first used to determine the generator-load pair most sensitive to each branch in the interface. The generator-load pairs are then used to realize accurate small disturbances by controlling the branch power flow in increasing and decreasing directions to obtain new equilibrium points around the initial equilibrium point. And, continuous power flow is used starting from such new points to get the corresponding critical points around the initial critical point on the CVSR boundary. Then a hyperplane cross the initial critical point can be calculated by solving a set of linear algebraic equations. Finally, the presented method is validated by some systems, including New England 39-bus system, IEEE 118-bus system, and EPRI-1000 bus system. It can be revealed that the method is computationally more efficient and has less approximation error. It provides a useful approach for power system online voltage stability monitoring and assessment. This work is supported by National Natural Science Foundation of China (No. 50707019), Special Fund of the National Basic Research Program of China (No. 2009CB219701), Foundation for the Author of National Excellent Doctoral Dissertation of PR China (No. 200439), Tianjin Municipal Science and Technology Development Program (No. 09JCZDJC25000), National Major Project of Scientific and Technical Supporting Programs of China During the 11th Five-year Plan Period (No. 2006BAJ03A06). ©2009 State Grid Electric Power Research Institute Press.

Balanced-budget consumption taxes and aggregate stability in a small open economy

In a small open economy facing a perfect world capital market, this paper shows that if the government follows a balanced-budget fiscal policy based on endogenous consumption tax rates, then the steady state is saddle-path stable and hence beliefs-driven aggregate instability can be ruled out. This result is in contrast to those obtained in some closed economy models, and it suggests that unrestricted world capital mobility can help stabilize the economy under the balanced-budget fiscal policy based on consumption taxation.

Sodium dodecyl sulfate (SDS) effect on the thermal stability of oxy-HbGp: Dynamic light scattering (DLS) and small angle X-ray scattering (SAXS) studies

Glossoscolex paulistus (HbGp) hemoglobin is an oligomeric protein, presenting a quaternary structure constituted by 144 globin and 36 non-globin chains (named linkers) with a total molecular mass of 3.6MDa. SDS effects on the oxy-HbGp thermal stability were studied, by DLS and SAXS, at pH 5.0, 7.0 and 9.0. DLS and SAXS data show that the SDS-oxy-HbGp interactions induce a significant decrease of the protein thermal stability, with the formation of larger aggregates, at pH 5.0. At pH 7.0, oxy-HbGp undergoes complete oligomeric dissociation, with increase of temperature, in the presence of SDS. Besides, oxy-HbGp 3.0mg/mL, pH 7.0, in the presence of SDS, has the oligomeric dissociation process reduced as compared to 0.5mg/mL of protein. At pH 9.0, oxy-HbGp starts to dissociate at 20°C, and the protein is totally dissociated at 50°C. The thermal dissociation kinetic data show that oxy-HbGp oligomeric dissociation at pH 7.0, in the presence of SDS, is strongly dependent on the protein concentration. At 0.5mg/mL of protein, the oligomeric dissociation is complete and fast at 40 and 42°C, with kinetic constants of (2.1±0.2)×10-4 and (5.5±0.4)×10-4s-1, respectively, at 0.6mmol/L SDS. However, at 3.0mg/mL, the oligomeric dissociation process starts at 46°C, and only partial dissociation, accompanied by aggregates formation is observed. Moreover, our data show, for the first time, that, for 3.0mg/mL of protein, the oligomeric dissociation, denaturation and aggregation phenomena occur simultaneously, in the presence of SDS. Our present results on the surfactant-HbGp interactions and the protein thermal unfolding process correspond to a step forward in the understanding of SDS effects. © 2013 Elsevier B.V.

Cetyltrimethylammonium chloride (CTAC) effect on the thermal stability of oxy-HbGp: Dynamic light scattering (DLS) and small angle X-ray scattering (SAXS) studies

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Primary stability in cementless total hip replacement: measurement techniques and aided-surgery

Primary stability of stems in cementless total hip replacements is recognized to play a critical role for long-term survival and thus for the success of the overall surgical procedure. In Literature, several studies addressed this important issue. Different approaches have been explored aiming to evaluate the extent of stability achieved during surgery. Some of these are in-vitro protocols while other tools are coinceived for the post-operative assessment of prosthesis migration relative to the host bone. In vitro protocols reported in the literature are not exportable to the operating room. Anyway most of them show a good overall accuracy. The RSA, EBRA and the radiographic analysis are currently used to check the healing process of the implanted femur at different follow-ups, evaluating implant migration, occurance of bone resorption or osteolysis at the interface. These methods are important for follow up and clinical study but do not assist the surgeon during implantation. At the time I started my Ph.D Study in Bioengineering, only one study had been undertaken to measure stability intra-operatively. No follow-up was presented to describe further results obtained with that device. In this scenario, it was believed that an instrument that could measure intra-operatively the stability achieved by an implanted stem would consistently improve the rate of success. This instrument should be accurate and should give to the surgeon during implantation a quick answer concerning the stability of the implanted stem. With this aim, an intra-operative device was designed, developed and validated. The device is meant to help the surgeon to decide how much to press-fit the implant. It is essentially made of a torsional load cell, able to measure the extent of torque applied by the surgeon to test primary stability, an angular sensor that measure the relative angular displacement between stem and femur, a rigid connector that enable connecting the device to the stem, and all the electronics for signals conditioning. The device was successfully validated in-vitro, showing a good overall accuracy in discriminating stable from unstable implants. Repeatability tests showed that the device was reliable. A calibration procedure was then performed in order to convert the angular readout into a linear displacement measurement, which is an information clinically relevant and simple to read in real-time by the surgeon. The second study reported in my thesis, concerns the evaluation of the possibility to have predictive information regarding the primary stability of a cementless stem, by measuring the micromotion of the last rasp used by the surgeon to prepare the femoral canal. This information would be really useful to the surgeon, who could check prior to the implantation process if the planned stem size can achieve a sufficient degree of primary stability, under optimal press fitting conditions. An intra-operative tool was developed to this aim. It was derived from a previously validated device, which was adapted for the specific purpose. The device is able to measure the relative micromotion between the femur and the rasp, when a torsional load is applied. An in-vitro protocol was developed and validated on both composite and cadaveric specimens. High correlation was observed between one of the parameters extracted form the acquisitions made on the rasp and the stability of the corresponding stem, when optimally press-fitted by the surgeon. After tuning in-vitro the protocol as in a closed loop, verification was made on two hip patients, confirming the results obtained in-vitro and highlighting the independence of the rasp indicator from the bone quality, anatomy and preserving conditions of the tested specimens, and from the sharpening of the rasp blades. The third study is related to an approach that have been recently explored in the orthopaedic community, but that was already in use in other scientific fields. It is based on the vibration analysis technique. This method has been successfully used to investigate the mechanical properties of the bone and its application to evaluate the extent of fixation of dental implants has been explored, even if its validity in this field is still under discussion. Several studies have been published recently on the stability assessment of hip implants by vibration analysis. The aim of the reported study was to develop and validate a prototype device based on the vibration analysis technique to measure intra-operatively the extent of implant stability. The expected advantages of a vibration-based device are easier clinical use, smaller dimensions and minor overall cost with respect to other devices based on direct micromotion measurement. The prototype developed consists of a piezoelectric exciter connected to the stem and an accelerometer attached to the femur. Preliminary tests were performed on four composite femurs implanted with a conventional stem. The results showed that the input signal was repeatable and the output could be recorded accurately. The fourth study concerns the application of the device based on the vibration analysis technique to several cases, considering both composite and cadaveric specimens. Different degrees of bone quality were tested, as well as different femur anatomies and several levels of press-fitting were considered. The aim of the study was to verify if it is possible to discriminate between stable and quasi-stable implants, because this is the most challenging detection for the surgeon in the operation room. Moreover, it was possible to validate the measurement protocol by comparing the results of the acquisitions made with the vibration-based tool to two reference measurements made by means of a validated technique, and a validated device. The results highlighted that the most sensitive parameter to stability is the shift in resonance frequency of the stem-bone system, showing high correlation with residual micromotion on all the tested specimens. Thus, it seems possible to discriminate between many levels of stability, from the grossly loosened implant, through the quasi-stable implants, to the definitely stable one. Finally, an additional study was performed on a different type of hip prosthesis, which has recently gained great interest thus becoming fairly popular in some countries in the last few years: the hip resurfacing prosthesis. The study was motivated by the following rationale: although bone-prosthesis micromotion is known to influence the stability of total hip replacement, its effect on the outcome of resurfacing implants has not been investigated in-vitro yet, but only clinically. Thus the work was aimed at verifying if it was possible to apply to the resurfacing prosthesis one of the intraoperative devices just validated for the measurement of the micromotion in the resurfacing implants. To do that, a preliminary study was performed in order to evaluate the extent of migration and the typical elastic movement for an epiphyseal prosthesis. An in-vitro procedure was developed to measure micromotions of resurfacing implants. This included a set of in-vitro loading scenarios that covers the range of directions covered by hip resultant forces in the most typical motor-tasks. The applicability of the protocol was assessed on two different commercial designs and on different head sizes. The repeatability and reproducibility were excellent (comparable to the best previously published protocols for standard cemented hip stems). Results showed that the procedure is accurate enough to detect micromotions of the order of few microns. The protocol proposed was thus completely validated. The results of the study demonstrated that the application of an intra-operative device to the resurfacing implants is not necessary, as the typical micromovement associated to this type of prosthesis could be considered negligible and thus not critical for the stabilization process. Concluding, four intra-operative tools have been developed and fully validated during these three years of research activity. The use in the clinical setting was tested for one of the devices, which could be used right now by the surgeon to evaluate the degree of stability achieved through the press-fitting procedure. The tool adapted to be used on the rasp was a good predictor of the stability of the stem. Thus it could be useful for the surgeon while checking if the pre-operative planning was correct. The device based on the vibration technique showed great accuracy, small dimensions, and thus has a great potential to become an instrument appreciated by the surgeon. It still need a clinical evaluation, and must be industrialized as well. The in-vitro tool worked very well, and can be applied for assessing resurfacing implants pre-clinically.

Power system stability of a small sized isolated network supplied by a combined wind-pumped storage generation system: a case study in the Canary Islands

Massive integration of renewable energy sources in electrical power systems of remote islands is a subject of current interest. The increasing cost of fossil fuels, transport costs to isolated sites and environmental concerns constitute a serious drawback to the use of conventional fossil fuel plants. In a weak electrical grid, as it is typical on an island, if a large amount of conventional generation is substituted by renewable energy sources, power system safety and stability can be compromised, in the case of large grid disturbances. In this work, a model for transient stability analysis of an isolated electrical grid exclusively fed from a combination of renewable energy sources has been studied. This new generation model will be installed in El Hierro Island, in Spain. Additionally, an operation strategy to coordinate the generation units (wind, hydro) is also established. Attention is given to the assessment of inertial energy and reactive current to guarantee power system stability against large disturbances. The effectiveness of the proposed strategy is shown by means of simulation results.

Safety and operability of small fishing vessels: study of a series of stability-related accidents

The intact stability of five small Spanish fishing vessels with ages between 3 and 8 years old which sunk in stability related accidents between 2004 and 2007 is compared to the stability of the fishing vessels which were retired from service to build those. The seakeeping performance of both sets of vessels is also compared. The differences found between the results obtained by the two methods have been analyzed. The suitability of seakeeping methods to assess stability performance is discussed.

Fishing effort control regulations influence on stability, safety and operability of small fishing vessels: study of a series of stability related accidents occurred in Spain between 2004 and 2007

Entre los años 2004 y 2007 se hundieron por problemas de estabilidad cinco pesqueros españoles de pequeña eslora, de características parecidas, de relativamente poca edad, que habían sido construidos en un intervalo de pocos años. La mayoría de los tripulantes de esos pesqueros fallecieron o desaparecieron en esos accidentes. Este conjunto de accidentes tuvo bastante repercusión social y mediática. Entre ingenieros navales y marinos del sector de la pesca se relacionó estos accidentes con los condicionantes a los diseños de los pesqueros impuestos por la normativa de control de esfuerzo pesquero. Los accidentes fueron investigados y publicados sus correspondientes informes; en ellos no se exploró esta supuesta relación. Esta tesis pretende investigar la relación entre esos accidentes y los cambios de la normativa de esfuerzo pesquero. En la introducción se expone la normativa de control de esfuerzo pesquero analizada, se presentan datos sobre la estructura de la flota pesquera en España y su accidentalidad, y se detallan los criterios de estabilidad manejados durante el trabajo, explicando su relación con la seguridad de los pesqueros. Seguidamente se realiza un análisis estadístico de la siniestralidad en el sector de la pesca para establecer si el conjunto de accidentes estudiados supone una anomalía, o si por el contrario el conjunto de estos accidentes no es relevante desde el punto de vista estadístico. Se analiza la siniestralidad a partir de diversas bases de datos de buques pesqueros en España y se concluye que el conjunto de accidentes estudiados supone una anomalía estadística, ya que la probabilidad de ocurrencia de los cinco sucesos es muy baja considerando la frecuencia estimada de pérdidas de buques por estabilidad en el subsector de la flota pesquera en el que se encuadran los cinco buques perdidos. A continuación el trabajo se centra en la comparación de los buques accidentados con los buques pesqueros dados de baja para construir aquellos, según exige la normativa de control de esfuerzo pesquero; a estos últimos buques nos referiremos como “predecesores” de los buques accidentados. Se comparan las dimensiones principales de cada buque y de su predecesor, resultando que los buques accidentados comparten características de diseño comunes que son sensiblemente diferentes en los buques predecesores, y enlazando dichas características de diseño con los requisitos de la nueva normativa de control del esfuerzo pesquero bajo la que se construyeron estos barcos. Ello permite establecer una relación entre los accidentes y el mencionado cambio normativo. A continuación se compara el margen con que se cumplían los criterios reglamentarios de estabilidad entre los buques accidentados y los predecesores, encontrándose que en cuatro de los cinco casos los predecesores cumplían los criterios de estabilidad con mayor holgura que los buques accidentados. Los resultados obtenidos en este punto permiten establecer una relación entre el cambio de normativa de esfuerzo pesquero y la estabilidad de los buques. Los cinco buques accidentados cumplían con los criterios reglamentarios de estabilidad en vigor, lo que cuestiona la relación entre esos criterios y la seguridad. Por ello se extiende la comparativa entre pesqueros a dos nuevos campos relacionados con la estabilidad y la seguridad delos buques: • Movimientos a bordo (operatividad del buque), y • Criterios de estabilidad en condiciones meteorológicas adversas El estudio de la operatividad muestra que los buques accidentados tenían, en general, una mayor operatividad que sus predecesores, contrariamente a lo que sucedía con el cumplimiento de los criterios reglamentarios de estabilidad. Por último, se comprueba el desempeño de los diez buques en dos criterios específicos de estabilidad en caso de mal tiempo: el criterio IMO de viento y balance intenso, y un criterio de estabilidad de nueva generación, incluyendo la contribución original del autor de considerar agua en cubierta. Las tendencias observadas en estas dos comparativas son opuestas, lo que permite cuestionar la validez del último criterio sin un control exhaustivo de los parámetros de su formulación, poniendo de manifiesto la necesidad de más investigaciones sobre ese criterio antes de su adopción para uso regulatorio. El conjunto de estos resultados permite obtener una serie de conclusiones en la comparativa entre ambos conjuntos de buques pesqueros. Si bien los resultados de este trabajo no muestran que la aprobación de la nueva normativa de esfuerzo pesquero haya significado una merma general de seguridad en sectores enteros de la flota pesquera, sí se concluye que permitió que algunos diseños de buques pesqueros, posiblemente en busca de la mayor eficiencia compatible con dicha normativa, quedaran con una estabilidad precaria, poniendo de manifiesto que la relación entre seguridad y criterios de estabilidad no es unívoca, y la necesidad de que éstos evolucionen y se adapten a los nuevos diseños de buques pesqueros para continuar garantizando su seguridad. También se concluye que la estabilidad es un aspecto transversal del diseño de los buques, por lo que cualquier reforma normativa que afecte al diseño de los pesqueros o su forma de operar debería estar sujeta a evaluación por parte de las autoridades responsables de la seguridad marítima con carácter previo a su aprobación. ABSTRACT Between 2004 and 2007 five small Spanish fishing vessels sank in stability related accidents. These vessels had similar characteristics, had relatively short age, and had been built in a period of a few years. Most crewmembers of these five vessels died or disappeared in those accidents. This set of accidents had significant social and media impact. Among naval architects and seamen of the fishing sector these accidents were related to the design constraints imposed by the fishing control effort regulations. The accidents were investigated and the official reports issued; this alleged relationship was not explored. This thesis aims to investigate the relationship between those accidents and changes in fishing effort control regulations. In the introduction, the fishing effort control regulation is exposed, data of the Spanish fishing fleet structure and its accident rates are presented, and stability criteria dealt with in this work are explained, detailing its relationship with fishing vessel safety. A statistical analysis of the accident rates in the fishing sector in Spain is performed afterwards. The objective is determining whether the set of accidents studied constitute an anomaly or, on the contrary, they are not statistically relevant. Fishing vessels accident rates is analyzed from several fishing vessel databases in Spain. It is concluded that the set of studied accidents is statistically relevant, as the probability of occurrence of the five happenings is extremely low, considering the loss rates in the subsector of the Spanish fishing fleet where the studied vessels are fitted within. From this point the thesis focuses in comparing the vessels lost and the vessels that were decommissioned to build them as required by the fishing effort control regulation; these vessels will be referred to as “predecessors” of the sunk vessels. The main dimensions between each lost vessel and her predecessor are compared, leading to the conclusion that the lost vessels share design characteristics which are sensibly different from the predecessors, and linking these design characteristics with the requirements imposed by the new fishing control effort regulations. This allows establishing a relationship between the accidents and this regulation change. Then the margin in fulfilling the regulatory stability criteria among the vessels is compared, resulting, in four of the five cases, that predecessors meet the stability criteria with greater clearance than the sunk vessels. The results obtained at this point would establish a relationship between the change of fishing effort control regulation and the stability of vessels. The five lost vessels complied with the stability criteria in force, so the relation between these criteria and safety is put in question. Consequently, the comparison among vessels is extended to other fields related to safety and stability: • Motions onboard (operability), and • Specific stability criteria in rough weather The operability study shows that the lost vessels had in general greater operability than their predecessors, just the opposite as when comparing stability criteria. Finally, performance under specific rough weather stability criteria is checked. The criteria studied are the IMO Weather Criterion, and one of the 2nd generation stability criteria under development by IMO considering in this last case the presence of water on deck, which is an original contribution by the author. The observed trends in these two cases are opposite, allowing to put into question the last criterion validity without an exhaustive control of its formulation parameters; indicating that further research might be necessary before using it for regulatory purposes. The analysis of this set of results leads to some conclusions when comparing both groups of fishing vessels. While the results obtained are not conclusive in the sense that the entry into force of a new fishing effort control in 1998 caused a generalized safety reduction in whole sectors of the Spanish fishing fleet, it can be concluded that it opened the door for some vessel designs resulting with precarious stability. This evidences that the relation between safety and stability criteria is not univocal, so stability criteria needs to evolve for adapting to new fishing vessels designs so their safety is still guaranteed. It is also concluded that stability is a transversal aspect to ship design and operability, implying that any legislative reform affecting ship design or operating modes should be subjected to assessing by the authorities responsible for marine safety before being adopted.

Analytical study of the thermal behaviour and stability of a small satellite

In this work the thermal analysis of a small satellite orbiting around the Earth has been approached by direct integration of the heat balance equations of a two-node reduced model, obtaining a linearized second order ODE problem, similar in form to the classical case of the forced vibration of a damped system. As the thermal loads (solar radiation, albedo, etc.) are harmonic, the problem is solved by means of Fourier analysis methods. Research on that field can be directly applied to the analysis of thermal problems and the results obtained are satisfactory. Working on the frequency domain streamlines the analysis, simplifies the study and facilitates the experimental testing. The transfer functions are obtained for the two-node case but the study can be extended to an n-node model.

The TOR (target of rapamycin) signal transduction pathway regulates the stability of translation initiation factor eIF4G in the yeast Saccharomyces cerevisiae

Initiation factor eIF4G is an essential protein required for initiation of mRNA translation via the 5′ cap-dependent pathway. It interacts with eIF4E (the mRNA 5′ cap-binding protein) and serves as an anchor for the assembly of further initiation factors. With treatment of Saccharomyces cerevisiae with rapamycin or with entry of cells into the diauxic phase, eIF4G is rapidly degraded, whereas initiation factors eIF4E and eIF4A remain stable. We propose that nutritional deprivation or interruption of the TOR signal transduction pathway induces eIF4G degradation.