Avaliação de diversos métodos de detecção de cistos de Giardia spp. e Oocistos de Cryptosporidium parvum presentes no resíduo gerado após o tratamento de água de abastecimento com turbidez elevada

Este trabalho teve como objetivo avaliar diversos métodos de detecção e recuperação de cistos de Giardia spp. e de oocistos de Cryptosporidium parvum em resíduos gerados no tratamento de águas de abastecimento com turbidez elevada tendo como padrão o Método 1623.1 da USEPA (2012 ). Para tanto, ensaios utilizando aparelho Jarteste (coagulação, floculação, decantação e filtração ) foram realizados utilizando o coagulante cloreto de polialumínio - PAC. Em todos os métodos avaliados foi utilizada a técnica de purificação por separação imunomagnética - IMS. A adaptação do método floculação em carbonato de cálcio FCCa elaborado por Vesey et al. (1993) e adaptado por Feng et al. (2011), repercutiu nos melhores resultados para a amostra de resíduo sedimentado, com recuperações de 68 ± 17 % para oocisto de C. parvum e de 42 ± 7 % para cisto de Giardia spp. Entretanto, as recuperações para a amostra de água de lavagem dos filtros - ALF foram inferiores à 1 %, não sendo possível determinar um método adequado. A presença dos patógenos indica que o reuso da ALF em ETA convencionais ou o descarte em mananciais sem um tratamento prévio, pode representar problemas de contaminação. A adaptação dos métodos de Boni de Oliveira (2012) e Keegan et al. (2008), também repercutiram em porcentagens de recuperação expressivas para a amostra de resíduo sedimentado, sendo de: 41 ± 35 % para oocisto de C. parvum e 11 ± 70 % para cisto de Giardia spp., e 38 ± 26 % para oocisto de C. parvum e 26 ± 13 % para cisto de Giardia spp., respectivamente. A análise estatística não resultou em diferença significativa entre estes dois métodos, entretanto, as elevadas recuperações indicam que estes métodos podem ser melhor avaliados em pesquisas futuras.

Filmes e coberturas a base do resíduo da extração de corante de cúrcuma

O objetivo deste trabalho foi avaliar o potencial de uso do resíduo da extração de pigmento de cúrcuma na produção de filmes e coberturas. Para o estudo dos filmes, foram utilizados glicerol e sorbitol como plastificantes e avaliados os efeitos da concentração de farinha de cúrcuma e do plastificante sobre as propriedades mecânicas, solubilidade, permeabilidade ao vapor de água (PVA), molhabilidade, atividade antioxidante, teor de curcuminóides e teor de compostos fenólicos totais utilizando um Delineamento Central Composto Rotacional 22, e os resultados foram avaliados utilizando a metodologia de superfície de resposta (MSR). A concentração de farinha afetou de forma positiva a espessura, PVA e o teor de curcuminóides totais dos filmes plastificados com glicerol e sorbitol. Entretanto, esta variável afetou as propriedades de solubilidade, molhabilidade e teor de compostos fenólicos totais somente dos filmes com glicerol. A concentração de plastificante (glicerol ou sorbitol) afetou significativamente a solubilidade, PVA e molhabilidade de ambos os filmes. Filmes de farinha de cúrcuma com boas propriedades mecânicas, baixa permeabilidade ao vapor de água, alta atividade antioxidante, alto teor de curcuminóides e alto teor de compostos fenólicos totais podem ser produzidos utilizando 27,9 a 30 g glicerol/100 g farinha ou 30 a 42 g sorbitol/100 g farinha e concentração de farinha na faixa de 5% a 6,41%. A cobertura de farinha de cúrcuma contendo 6% de farinha e 30 g glicerol/100 g de farinha foi aplicada em bananas Maçã (Musa acuminata) armazenadas a 27ºC e 65% UR. Assim, foi avaliado o efeito da cobertura na qualidade pós-colheita das bananas em função à suas características físico-químicas como perda de massa, firmeza da polpa, pH, acidez titulável, sólidos solúveis, açúcares redutores e cor da casca. Os resultados mostraram que a cobertura foi eficiente em diminuir a perda de massa, o teor de açúcares redutores, a acidez, a perda da firmeza e a cor da casca principalmente durante a etapa de maturação do fruto. Entretanto, não foi observado grande efeito da cobertura sobre o pH e o teor de sólidos solúveis durante o período estudado. As bananas sem a cobertura tiveram vida útil de 6 dias, enquanto as bananas com cobertura tiveram vida útil de 9 dias.

Estudo da substituição da fluorita por alumina ou sodalita e de cal por resíduo de mármore em escórias sintéticas dessulfurantes.

A siderurgia vem sofrendo transformações que buscam inovação e matérias-primas alternativas. Dentro deste contexto, o uso de resíduos industriais para a formação de escórias sintéticas é tido como alternativa na busca de novos materiais e rotas de reaproveitamento de resíduos. Portanto, este trabalho teve como objetivo estudar o uso de escórias sintéticas na etapa de dessulfuração do ferro-gusa, aço e ferro fundido. Assim como, propor a utilização da sodalita e da alumina em substituição à fluorita e o resíduo de mármore em substituição à cal convencional. Inicialmente, o resíduo foi caracterizado utilizando as seguintes técnicas: análise química, análise granulométrica, área de superfície específica, difração de raios-X, microscopia eletrônica de varredura (MEV) e análise de espectroscopia por energia dispersiva (EDS). Os resultados da caracterização mostraram que aproximadamente 90% das partículas do resíduo de mármore estão abaixo de 100m e sua área superficial foi de 0,24m²/g. Através da difração de raios-X foi observado que o resíduo é composto por CaCO3, MgCO3 e SiO2. Na sequência, foram feitas simulações com o software Thermo-Calc para obter dados termodinâmicos das fases presentes nas misturas e compará-los com os resultados experimentais. Além disso, também foram calculados dados de capacidade de sulfeto (Cs), partição de enxofre (Ls) e basicidade ótica () das misturas iniciais. Posteriormente, foram realizados os ensaios experimentais em escala laboratorial para ferro-gusa, ferro fundido e aço, respectivamente nas temperaturas de 1400°C, 1550°C e 1600°C. Nos ensaios de dessulfuração do aço e do ferro-gusa, utilizou-se um rotor de alumina com o objetivo de favorecer a agitação no metal e aumentar a remoção de enxofre. Na etapa de dessulfuração do ferro-gusa, constatou-se que a fase sólida de CaO é a responsável pela remoção de enxofre e que a presença das fases silicato tricálcio e aluminato tricálcio (3CaO.SiO2 e 3CaO.Al2O3) limitam a reação, sendo maiores suas concentrações nas escórias que utilizaram o resíduo de mármore e sodalita, devido a presença de SiO2 e Al2O3 nestas matérias-primas. Já para o aço e o ferro fundido, que foram estudados com escórias à base de CaO e Al2O3, observou-se que o aumento da fase líquida favoreceu a dessulfuração. Verificou-se que a dessulfuração no ferro fundido foi por escória de topo e no aço por um processo misto, onde a fase líquida e fase sólida participaram da dessulfuração.

Utilização de resíduo de mármore e de óxido de boro em escórias sintéticas dessulfurantes para aços.

O mercado atual exige das indústrias siderúrgicas aços de melhor qualidade produzidos por meio de processos que causem menor impacto ao meio ambiente. Dessa forma, este trabalho teve como objetivo reciclar o resíduo de mármore gerado na indústria de rochas ornamentais, que possui em sua composição óxido de cálcio (CaO) e óxido de magnésio (MgO). O CaO é suficiente para substituir a cal nas escórias e o MgO contribui para a diminuição do desgaste dos refratários, através do emprego do resíduo no processo produtivo do aço. Além disso, foi realizada a substituição da fluorita por óxido de boro como fluxante na composição de misturas dessulfurantes. O resíduo de mármore foi caracterizado utilizando as seguintes técnicas: análise química via EDXFR, análise granulométrica via espalhamento de luz, área de superfície específica pelo método BET, difração de raios-X, microscopia eletrônica de varredura (MEV) e análise de micro-regiões por EDS. Visando verificar a eficiência na dessulfuração, foram formuladas misturas sintéticas utilizando a cal convencional ou resíduo de mármore, e a fluorita ou o óxido de boro. As misturas foram formuladas com o auxílio dos programas de termodinâmica computacional, Thermo-Calc e FactSage. Estas misturas foram adicionadas no aço fundido a temperatura de 1600°C sob atmosfera de argônio e agitadas por meio de um rotor de alumina. Amostras de metal foram retiradas para verificar a variação do teor de enxofre durante o experimento. O resíduo de mármore caracterizado, apresentou em sua composição 40% de CaO e 14% de MgO, na forma dos carbonatos CaCO3 e MgCO3. Obteve uma perda de massa de 42,1%, na forma de CO2 a temperatura de 780°C. Os experimentos mostraram que, as misturas testadas apresentaram, na maioria dos casos, eficiência de dessulfuração acima de 60%.

Utilização do resíduo grosso do beneficiamento da scheelita em aplicações rodoviárias

Mining is an activity of great economic and social value, assisting in the development of the country. However, it can be extremely harmful to the environment if no proper waste management study exists as mitigation measure its effects. Sample some of these harmful effects are pollution: water, through the seepage of waste into the groundwater; soil; of fauna and flora; sound (due to the noise of machines); visual from the residue stored in the open, changing the local landscape; and air. One way to mitigate environmental impacts caused by mining is the proper management of their waste through their use on highways. To that end, this paper proposes to give an appropriate destination to grit coming from the beneficiation of scheelite, due to mining activity from mining group Tomaz Salustino in Brejuí mine, located in the city of Currais Novos in the state of Rio Grande do Norte. This work was developed in four stages. The first comprised the chemical and mineralogical tests, DRX and FRX in which they sought to discover the composition of the material studied. The next step involved the physical characteristics of the waste by means of specific tests and grinding the solid mass, LL and LP. The third stage included the specific tests applied to the pavement, with the compaction test and test Index Support California. Finally, the fourth stage was the mechanical characterization, represented by direct shear tests, both in the flooded condition and not in flooded condition. The technical feasibility of using the modified energie compacted in layers of subbase power has been verified. In normal and intermediate energies is feasible to use less noble as layers as the subgrade. The incorporation of the waste in layers of road pavements provide an alternative to conventionally used in paving aggregates, providing a proper disposal of tailings from scheelite, as well as environmental preservation

Secagem de resíduo de goiaba em secador convectivo de bandejas: modelagem matemática e análise do processo

Actually, Brazil is one of the larger fruit producer worldwide, with most of its production being consumed in nature way or either as juice or pulp. It is important to highlig ht in the fruit productive chain there are a lot lose due mainly to climate reasons, as well as storage, transportation, season, market, etc. It is known that in the pulp and fruit processing industy a yield of 50% (in mass) is usually obtained, with the other part discarded as waste. However, since most this waste has a high nutrient content it can be used to generate added - value products. In this case, drying plays an important role as an alternative process in order to improve these wastes generated by the fruit industry. However, despite the advantage of using this technique in order to improve such wastes, issues as a higher power demand as well as the thermal efficiency limitation should be addressed. Therefore, the control of the main variables in t his drying process is quite important in order to obtain operational conditions to produce a final product with the target specification as well as with a lower power cost. M athematical models can be applied to this process as a tool in order to optimize t he best conditions. The main aim of this work was to evaluate the drying behaviour of a guava industrial pulp waste using a batch system with a convective - tray dryer both experimentally and using mathematical modeling. In the experimental study , the dryin g carried out using a group of trays as well as the power consume were assayed as response to the effects of operational conditions (temperature, drying air flow rate and solid mass). Obtained results allowed observing the most significant variables in the process. On the other hand, the phenomenological mathematical model was validated and allowed to follow the moisture profile as well as the temperature in the solid and gas phases in every tray. Simulation results showed the most favorable procedure to o btain the minimum processing time as well as the lower power demand.

Uso da cinza do bagaço da cana-de-açúcar como matéria-prima na substituição dos fundentes para aplicações em porcelanato

The present study aims to evaluate the potential use of bagasse ash from sugar cane (CBC) as a flux, replacing phyllite and/or feldspar in standard industrial mass production of enameled porcelain, verifying the possibility of the CBC contribute to the overall reduction of the coefficient of thermal expansion of the ceramic mass. To this end, as a result of the research, we characterized the raw material components of the standard mass (clay, phyllite, kaolin, feldspar, quartz and talc) and the residue of BCC, by testing by XRF, XRD, AG, DTA and ATG. Specimens (CDP) were manufactured in the dimensions of 100 mm x 50 mm x 8 mm in uniaxial matrix under compaction pressure of 33 MPa, assembled in batches of 3 units subsequently sintered at temperatures of 1150°C to 1210°C by varying the Rating Scale at 10°C, heating and cooling ramp of 50°C/min and 25°C/min, with levels of 1 min, 3 min, 5 min, 8 min, 10 min, 15 min, 30 min and 60 min. analyzing the results of the physical properties of water absorption (WA), linear firing shrinkage (LFS), dilatometric analysis (DTA), flexural strain (SFT) and SEM of the sintered bodies in order to verify the adequacy of CDP to ISO 13006, ISO 10545, NBR 13816 standards; NBR 13817 and NBR 13818. The study showed that the formulations that best suit the requirements of the standards are:. G4 - which was applied in 10% of replacing the CBC phyllite, sintering temperature 1210 ° C for 10 min and porch, and F3 - with application of 7.5% of CBC to replace the feldspar in the sintering temperatures of 1190°C, 1200°C and 1210°C for 10 min and porch. These formulations showed better performance regarding the formation of primary and secondary mullite, with considerable reduction of cracks and pores, meeting the prerequisites of standards for glazed porcelain. The results shows that the use of the CBC as a flux in the preparation of porcelain mass meets standard parameters for the manufacture of the product, and thereby can reduce environmental impact and the cost of production. Therefore, it is recommended to use this residue in the ceramics industry, due to its industrial, commercial and collaborative viability for sustainability.

Uso de resíduos de queima de casca de café e argila da região sul da Bahia na obtenção de isolador elétrico cerâmico

The electrical ceramic insulators industry, uses noble raw materials such as siliceous and aluminous clays of white burning, in order to provide plasticity of the mass and contribute to electrical and mechanical properties required of the product, and feldspar with the flux function In literature references the composition of the masses indicates that the clay participates in percentage between 20 and 32, and feldspar 8 to 35, these materials have significant cost. In this research was performed the total replacement of commercial clay, for white burning clay from Santa Luzia region in southern Bahia and partial replacement of feldspar by ash residue of husk conilon coffee burning, from extreme south of Bahia. The objective of replacement these raw materials is to aver its technical feasibility and call attention for the embryo pole of ceramic industry for the existing in the south and extreme south of Bahia, which has significant reserves of noble raw materials such as clay white burning, kaolin, quartz and feldspar, and generates significant volume of gray husk conilon coffee as alternate flux. Clay Santa Luzia is prima noble material whose current commercial application is the production of white roofing. The residue of coffee husk ash is discarded near of production sites and is harmful to the environment. Phase diagrams and statistic design of experiments, were used for optimization and cost savings in research. The results confirmed the expectations of obtaining electrical ceramic insulators, with white burning clay of Santa Luzia and partial replacement up to 35.4% of feldspar, by treaty residue of conilon ash coffee husk burning. The statistic design that showed best results was for formulation with percentages of: clay 26.4 to 30.4%; kaolin 14.85 to 17.1%; feldspar 12.92 to 16.96%; R2 residue 7.08 to 9.2% and Quartz 32.5 to 38.75%, relative to the total mass of the mixture. The best results indicated; 0.2 to 1.4% apparent porosity , water absorption 0.1 to 0.7%, flexural strength 35 to 45MPa , dielectric strength 35-41 kV/cm , the transverse resistivity 8x109 2.5x1010 Ω.cm and for the dielectric constant ε/ε0 7 to 10.4, specification parameters for manufacturing ceramic electrical insulators of low and medium voltage.

Características bioativas, funcionais e efeito protetor do resíduo desidratado de camu-camu (Myrciaria dubia H.B.K. (McVaugh)) sobre doenças degenerativas utilizando modelos in vivo C. elegans

Camu-camu (Myrciaria dubia H.B.K. (McVaugh)) is a native Amazon fruit, recognized worldwide as one of the main natural sources of ascorbic acid. Due to its great acidity, this fruit is generally consumed after processing into juice or as ingredient in food preparations. As a co-product of the camu-camu processing, a significant amount of agroindustrial residue is generated. Despite the studies showing the bioactive value and biological potential of the fruit, few studies have approached the possible processing techniques, transformation and preservation of camu-camu fruits and its agroindustrial pomace. Therefore, the present work has the objective of evaluating two different drying processes applied to camu-camu pomace (peel and seeds with residual pulp), freeze drying and hot air drying, in order to obtain a functional fruit product. This thesis was divided into three stages: the first one shows the studies related to the freeze drying and hot air drying, where we demonstrated the impact of the selected drying techniques on the bioactive components of camu-camu, taking the fresh pomace as the control group. Among the investigated conditions, the groups obtained at 50ºC and 4 m/s (SC50) and 80ºC and 6 m/s (SC80) were selected as for further studies, based on their ascorbic acid final content and Folin-Ciocalteau reducing capacity. In addition to SC50 and SC80, the fresh pomace (RF) and freeze dried (RL) samples were also evaluated in these further stages of the research. Overall, the results show higher bioactive concentration in the RF samples, followed by RL, SC50 and SC80. On the second step of the research, the antioxidant, antimicrobial and antienzymatic activities were evaluated and the same tendency was observed. It was also reported, for the first time in the literature, the presence of syringic acid in dried camu-camu pomace. In the third and final stage of the research, it was investigated the effect of dried camu-camu on aging and neuroprotective disorders, using the in vivo model C.elegans. It was observed that camu-camu extracts were able to modulate important signaling genes relevant to thermal and oxidative stresses (p < 0.05). The polar acid, polar basic and polar neutral fractions obtained from the low molecular extracts of SC50 were able to extend the lifespan of wild type N2 C. elegans in 20% and 13% (p < 0.001). Results also showed that the paralysis induced by the β1-42 amyloid was significantly (p < 0.0001) retarded in CL4176 worms. Similarly, the camu-camu extracts attenuated the dopaminergic induction associated to Parkinson’s disease. Finally, a global analysis of the data presented here reveal that the camu-camu pomace, a co-product obtained from the industrial processing of a native Brazilian fruit, is a relevant natural source of health relevant compounds. This thesis, shows for the first time, the multifunctionality of camu-camu pomace, a natural resource still underexploited for scientific, commercial and technological purposes.

Incorporação do resíduo de cascalho de perfuração de poços de petróleo em formulações cerâmicas

During its operations, the oil industry generates a lot of waste, including gravel from drilling. Control of environmental impacts caused by this waste represents a major challenge. Such impacts can be minimized when it is given an appropriate management by being properly treated and properly disposed or recycled. The properties of these materials can be greatly influenced when a waste is added to its composition. This work aims to study the incorporation of gravel waste oil-well drilling in the standard body for production of red ceramic from a ceramic industry in São Gonçalo do Amarante / RN. The success of the incorporation can minimize costs in the production of ceramic pieces and reduce the environmental impacts caused by waste. The raw materials used were collected, characterized, and formulated with the percentages of 0%, 20% and 40% by weight of substitution of residue were synthesized at temperatures of 900, 1.010 and 1.120 °C using 30 minute firing intervals, 1 hour and 30min and 2 hours and 30 minutes, based on a factorial design 2³. Samples were then subjected to the tests of Water Absorption, Linear Retraction Firing, Flexural Rupture Strength, Apparent Porosity and Apparent Specific mass and Scanning Electron Microscopy (SEM) of break section. The results showed that the use of the residue for the manufacture of the ceramic products is possible (tiles, bricks and massive hollow bricks) replacing the clay to 40%, meeting the requirements of the standard and the literature for the technological properties of the final product.

Desenvolvimento de um painel sanduíche com carga de particulado oriundo de resíduo lignocelulósico para aplicação em produtos na área de equipamentos de proteção

This work aims to study and investigate the use of a hybrid composite polymer formed with blanket aramid (Kevlar 29) fiber blanket flax fiber and particulate dry endocarp of coconut (Cocos nucifera Linn), using as matrix an epoxy resin based thermoset for use in areas of protective equipment. Besides such material is used an aluminum plate, joined to the composite by means of glue based on epoxy and araldite commercial. The manufacturing process adopted was manual lamination (Hand Lay Up) to manufacture the hybrid composite. After the composite is prepared, an aluminum plate is subjected to pressure and glued to cure the adhesive. Layers of veil will also be used to separate the particulate from the linen blanket layer without disturbing the alignment of the fibers of the blankets. To characterize the mechanical and physical behavior was manufactured a plate of 800 x 600 mm of the hybrid composite, which were removed specimens for tests of water absorption to saturation; density; impact test (Charpy) and two test specimens for ballistic testing 220 mm x 200 mm to make a comparative study between the dry state and saturated water absorption and thus see the ballistic performance of these two conditions. The test was applied to make a comparative study of fracture in these two conditions, caused by penetrating ballistic missile (38 and 380). To test the impact (Charpy) will analyze the absorbed energy, fracture appearance and lateral contraction, also in dry condition and saturation of absorbed water, thereby analyzing situations where the impact load is relevant, such as bumps and shocks produced by stone, metal or wooden bars among others. The proposed configuration, along with the tests, has the purpose, application in the fields of equipment against ballistic impact, such as helmets; bullet proof vests; shields; protective packaging and other items to be identified in this research.

Estudo do aproveitamento de resíduos PAE no desenvolvimento de materiais cerâmicos

This work presents a new ceramic material obtained through the incorporation of solid waste from the steel industry and known as dedusting powder PAE - in ceramic formulations based on clay, potassium and sodium feldspars, kaolin and talc. Formulations were prepared with ceramic residue levels of 0% (basic mass - MB), 2%, 4% and 8%, subjected to firing at temperatures of 1000 ° C, 1050ºC, 1100ºC and 1150ºC for periods of 15 min. and 120 min. The physicchemical and mechanical properties of these ceramic formulations were determined based on the firing temperature, residence time in the oven and the percentage of waste. Since the physicochemical and mechanical properties of the sintered materials were evaluated by chemical analysis techniques (fluorescence X-rays - FRX), particle size distribution, specific surface area, apparent density, structural analysis by diffraction of X-rays (DRX) and characterization of surface by scanning electron microscopy (SEM). The magnetic response characteristics and the pattern of magnetic ferrites of the samples were analyzed in the assay conditions, having noticed that the saturation magnetic susceptibility depend on the sintering temperature of the material and it is associated with its crystal structure. From the analysis results, it was concluded that the ceramic material with better physical and mechanical properties is obtained when the 8% from PAE residue is added to standard formulation under the burn time of 15 minutes and temperature of 1150ºC.

Revestimento decorativo monocamada pigmentado, com resíduo de vidro temperado, para aplicação em fachadas

Although efficient from a technical point of view, mortar layers that make up the traditional masonry coating (slurry mortar, plaster and plaster) have to be in contradiction with the new construction technologies and more efficient methods of consumption and work rationalization. From an environmental point of view, the recovery of waste into new composites for the building has been a growing strand of studies in the scientific community, may prove to be a cost-effective solution in some cases. Thus, this research proposes the development of a mortar Decorative Coating Monolayer (RDM), for use in facades, produced on site, incorporating tempered glass waste (RVT) in the cement matrix, as a partial substitute for aggregate. Therefore, we adopted the binder respect / aggregate of 1: 6 (by volume), consistency index 250mm ± 20, sand substitution levels of glass waste 20%, 50% and 80% and relative water / cement varied in many traits. Two additives were used, a polymer, styrene-butadiene-based, and other chemical, besides mineral and silica fume inorganic pigment in colors red, yellow and blue. Mechanical tests were carried out on fresh pasta and hardened, as well as for the applied coating on masonry, so as to demonstrate the feasibility of the material. In addition, it verified the adequacy of the RDM built environment by means of thermal tests. The results demonstrated the feasibility of the proposed RDM with significantly higher values when compared to norms, especially the dash-added replacement content of 20% and addition of pigment in red. Therefore, the study shows the scientific community as an incentive to the use of technological innovations in construction, increasing the range of alternatives available for housing production, with the proposition of a material that achieves the desired functionality and obtain environmental gain, and may be adopted on construction sites as an alternative industrialized mortars.