Chain-link based HVDC voltage source converter using current injection

VSC converters are becoming more prevalent for HVDC applications. Two circuits are commercially available at present, a traditional six-switch, PWM inverter, implemented using series connected IGBTs - ABBs HVDC Light®, and the other a modular multi-level converter (MMC) - Siemens HVDC-PLUS. This paper presents an alternative MMC topology, which utilises a novel current injection technique, and exhibits several desirable characteristics.

Switched capacitor DC-DC converters for HVDC applications

DC distribution and transmission provides an efficient, cost effective and reliable alternative to traditional AC systems for offshore wind farm integration. High power DC-DC converters are key components to realise future offshore voltage DC grids and multi-terminal HVDC systems. Different DC-DC converter topologies have been proposed for this application. The aim of this paper is to investigate the viability of Switched Capacitor (SC) converters in high power application particularly the interconnection of offshore windfarms to a medium voltage DC grid. In addition, a comparison of alternative topologies that have been proposed will be presented. Simulation and experimental results are provided to verify the analysis.

Probabilistic Approach to Design of Large Antenna Arrays

2000 Mathematics Subject Classification: 78A50

Ultrahigh step-up dc-dc converter for distributed generation by three Degrees of Freedom (3DoF) approach

This paper proposes a novel dc-dc converter topology to achieve an ultrahigh step-up ratio while maintaining a high conversion efficiency. It adopts a three degree of freedom approach in the circuit design. It also demonstrates the flexibility of the proposed converter to combine with the features of modularity, electrical isolation, soft-switching, low voltage stress on switching devices, and is thus considered to be an improved topology over traditional dc-dc converters. New control strategies including the two-section output voltage control and cell idle control are also developed to improve the converter performance. With the cell idle control, the secondary winding inductance of the idle module is bypassed to decrease its power loss. A 400-W dc-dc converter is prototyped and tested to verify the proposed techniques, in addition to a simulation study. The step-up conversion ratio can reach 1:14 with a peak efficiency of 94% and the proposed techniques can be applied to a wide range of high voltage and high power distributed generation and dc power transmission.

Mechatronic solutions for measuring disturbance levels within a cochlea

Hearing implants are an important devices for combating deafness over the next 15 years. In this paper, we focus on the means to determine the sensitivity of the hearing organ to disturbances produced by implants and other interventions, and those induced by implantation. The preservation of residual hearing is an important aspect to be considered, however, the sensitivity of this to the process of implantation, device location and power levels is not well understood. Within this paper, a new experimental set-up to contrast the merits of different implantation techniques, implant location and power transmission are discussed and the initial results regarding disturbance levels using different surgical techniques are described.

Effects of alternating current voltage amplitude and oxide capacitance on mid-gap interface state defect density extractions in In0.53Ga 0.47As capacitors

This work looks at the effect on mid-gap interface state defect density estimates for In0.53Ga0.47As semiconductor capacitors when different AC voltage amplitudes are selected for a fixed voltage bias step size (100 mV) during room temperature only electrical characterization. Results are presented for Au/Ni/Al2O3/In0.53Ga0.47As/InP metal–oxide–semiconductor capacitors with (1) n-type and p-type semiconductors, (2) different Al2O3 thicknesses, (3) different In0.53Ga0.47As surface passivation concentrations of ammonium sulphide, and (4) different transfer times to the atomic layer deposition chamber after passivation treatment on the semiconductor surface—thereby demonstrating a cross-section of device characteristics. The authors set out to determine the importance of the AC voltage amplitude selection on the interface state defect density extractions and whether this selection has a combined effect with the oxide capacitance. These capacitors are prototypical of the type of gate oxide material stacks that could form equivalent metal–oxide–semiconductor field-effect transistors beyond the 32 nm technology node. The authors do not attempt to achieve the best scaled equivalent oxide thickness in this work, as our focus is on accurately extracting device properties that will allow the investigation and reduction of interface state defect densities at the high-k/III–V semiconductor interface. The operating voltage for future devices will be reduced, potentially leading to an associated reduction in the AC voltage amplitude, which will force a decrease in the signal-to-noise ratio of electrical responses and could therefore result in less accurate impedance measurements. A concern thus arises regarding the accuracy of the electrical property extractions using such impedance measurements for future devices, particularly in relation to the mid-gap interface state defect density estimated from the conductance method and from the combined high–low frequency capacitance–voltage method. The authors apply a fixed voltage step of 100 mV for all voltage sweep measurements at each AC frequency. Each of these measurements is repeated 15 times for the equidistant AC voltage amplitudes between 10 mV and 150 mV. This provides the desired AC voltage amplitude to step size ratios from 1:10 to 3:2. Our results indicate that, although the selection of the oxide capacitance is important both to the success and accuracy of the extraction method, the mid-gap interface state defect density extractions are not overly sensitive to the AC voltage amplitude employed regardless of what oxide capacitance is used in the extractions, particularly in the range from 50% below the voltage sweep step size to 50% above it. Therefore, the use of larger AC voltage amplitudes in this range to achieve a better signal-to-noise ratio during impedance measurements for future low operating voltage devices will not distort the extracted interface state defect density.

Conception d’un mécanisme déployable à grand ratio d’expansion et de son système d’actionnement par roues d’inertie pour applications spatiales

Cette thèse propose de développer des mécanismes déployables pour applications spatiales ainsi que des modes d’actionnement permettant leur déploiement et le contrôle de l’orientation en orbite de l’engin spatial les supportant. L’objectif étant de permettre le déploiement de surfaces larges pour des panneaux solaires, coupoles de télécommunication ou sections de station spatiale, une géométrie plane simple en triangle est retenue afin de pouvoir être assemblée en différents types de surfaces. Les configurations à membrures rigides proposées dans la littérature pour le déploiement de solides symétriques sont optimisées et adaptées à l’expansion d’une géométrie ouverte, telle une coupole. L’optimisation permet d’atteindre un ratio d’expansion plan pour une seule unité de plus de 5, mais présente des instabilités lors de l’actionnement d’un prototype. Le principe de transmission du mouvement d’un étage à l’autre du mécanisme est revu afin de diminuer la sensibilité des performances du mécanisme à la géométrie de ses membrures internes. Le nouveau modèle, basé sur des courroies crantées, permet d’atteindre des ratios d’expansion plans supérieurs à 20 dans certaines configurations. L’effet des principaux facteurs géométriques de conception est étudié afin d’obtenir une relation simple d’optimisation du mécanisme plan pour adapter ce dernier à différents contextes d’applications. La géométrie identique des faces triangulaires de chaque surface déployée permet aussi l’empilement de ces faces pour augmenter la compacité du mécanisme. Une articulation spécialisée est conçue afin de permettre le dépliage des faces puis leur déploiement successivement. Le déploiement de grandes surfaces ne se fait pas sans influencer lourdement l’orientation et potentiellement la trajectoire de l’engin spatial, aussi, différentes stratégies de contrôle de l’orientation novatrices sont proposées. Afin de tirer profit d’une grande surface, l’actionnement par masses ponctuelles en périphérie du mécanisme est présentée, ses équations dynamiques sont dérivées et simulées pour en observer les performances. Celles-ci démontrent le potentiel de cette stratégie de réorientation, sans obstruction de l’espace central du satellite de base, mais les performances restent en deçà de l’effet d’une roue d’inertie de masse équivalente. Une stratégie d’actionnement redondant par roue d’inertie est alors présentée pour différents niveaux de complexité de mécanismes dont toutes les articulations sont passives, c’est-à-dire non actionnées. Un mécanisme à quatre barres plan est simulé en boucle fermée avec un contrôleur simple pour valider le contrôle d’un mécanisme ciseau commun. Ces résultats sont étendus à la dérivation des équations dynamiques d’un mécanisme sphérique à quatre barres, qui démontre le potentiel de l’actionnement par roue d’inertie pour le contrôle de la configuration et de l’orientation spatiale d’un tel mécanisme. Un prototype à deux corps ayant chacun une roue d’inertie et une seule articulation passive les reliant est réalisé et contrôlé grâce à un suivi par caméra des modules. Le banc d’essai est détaillé, ainsi que les défis que l’élimination des forces externes ont représenté dans sa conception. Les résultats montrent que le système est contrôlable en orientation et en configuration. La thèse se termine par une étude de cas pour l’application des principaux systèmes développés dans cette recherche. La collecte de débris orbitaux de petite et moyenne taille est présentée comme un problème n’ayant pas encore eu de solution adéquate et posant un réel danger aux missions spatiales à venir. L’unité déployable triangulaire entraînée par courroies est dupliquée de manière à former une coupole de plusieurs centaines de mètres de diamètre et est proposée comme solution pour capturer et ralentir ces catégories de débris. Les paramètres d’une mission à cette fin sont détaillés, ainsi que le potentiel de réorientation que les roues d’inertie permettent en plus du contrôle de son déploiement. Près de 2000 débris pourraient être retirés en moins d’un an en orbite basse à 819 km d’altitude.

Determinação de metais em óleos lubrificantes utilizando a técnica de espectrometria de emissão óptica com plasma induzido por laser

IPEN/D

Método de análise de vulnerabilidade utilizando redes complexas : aplicação na rede de transporte aéreo brasileira

Dissertação (mestrado)—Universidade de Brasília, Faculdade de Tecnologia, Departamento de Engenharia Civil e Ambiental, 2016.

Modelagem e análise de um dispositivo mitigador de flecha para linhas de transmissão de energia elétrica baseado em ligas com memória de forma

Dissertação (mestrado)—Universidade de Brasília, Faculdade de Tecnologia, Departamento de Engenharia Mecânica, 2016.

Modelo de competencias en TIC para el personal de una organización del sector eléctrico

La presente investigación pretendió incorporar el uso intensivo de TIC en los procedimientos establecidos y necesarios en los procesos de generación, distribución y control de la energía, lo que se expresa en un manual para el sistema de gestión humana de la organización analizada. La investigación partió de un levantamiento de un estado del arte, continuó con la realización de un análisis de actitudes y aptitudes de los colaboradores, basado en propuestas teóricas y mejores prácticas existentes del medio, y, por último, concluyó con un manual de gestión humana en el que se indican las competencias en los diferentes perfiles de la organización para el uso de TIC y su aplicación, con el propósito de alinearse con las perspectivas y objetivos de la organización analizada al tener como base la perdurabilidad y la competitividad de la misma.

Models and algorithms for real-world optimization problems

This thesis deals with efficient solution of optimization problems of practical interest. The first part of the thesis deals with bin packing problems. The bin packing problem (BPP) is one of the oldest and most fundamental combinatorial optimiza- tion problems. The bin packing problem and its generalizations arise often in real-world ap- plications, from manufacturing industry, logistics and transportation of goods, and scheduling. After an introductory chapter, I will present two applications of two of the most natural extensions of the bin packing: Chapter 2 will be dedicated to an application of bin packing in two dimension to a problem of scheduling a set of computational tasks on a computer cluster, while Chapter 3 deals with the generalization of BPP in three dimensions that arise frequently in logistic and transportation, often com- plemented with additional constraints on the placement of items and characteristics of the solution, like, for example, guarantees on the stability of the items, to avoid potential damage to the transported goods, on the distribution of the total weight of the bins, and on compatibility with loading and unloading operations. The second part of the thesis, and in particular Chapter 4 considers the Trans- mission Expansion Problem (TEP), where an electrical transmission grid must be expanded so as to satisfy future energy demand at the minimum cost, while main- taining some guarantees of robustness to potential line failures. These problems are gaining importance in a world where a shift towards renewable energy can impose a significant geographical reallocation of generation capacities, resulting in the ne- cessity of expanding current power transmission grids.

Transmission loss allocation based on optimal power flow and sensitivity analysis

This paper presents a new approach to the transmission loss allocation problem in a deregulated system. This approach belongs to the set of incremental methods. It treats all the constraints of the network, i.e. control, state and functional constraints. The approach is based on the perturbation of optimum theorem. From a given optimal operating point obtained by the optimal power flow the loads are perturbed and a new optimal operating point that satisfies the constraints is determined by the sensibility analysis. This solution is used to obtain the allocation coefficients of the losses for the generators and loads of the network. Numerical results show the proposed approach in comparison to other methods obtained with well-known transmission networks, IEEE 14-bus. Other test emphasizes the importance of considering the operational constraints of the network. And finally the approach is applied to an actual Brazilian equivalent network composed of 787 buses, and it is compared with the technique used nowadays by the Brazilian Control Center. (c) 2007 Elsevier Ltd. All rights reserved.

Hybrid fuzzy Monte Carlo technique for reliability assessment in transmission power systems

This paper proposes a new methodology to reduce the probability of occurring states that cause load curtailment, while minimizing the involved costs to achieve that reduction. The methodology is supported by a hybrid method based on Fuzzy Set and Monte Carlo Simulation to catch both randomness and fuzziness of component outage parameters of transmission power system. The novelty of this research work consists in proposing two fundamentals approaches: 1) a global steady approach which deals with building the model of a faulted transmission power system aiming at minimizing the unavailability corresponding to each faulted component in transmission power system. This, results in the minimal global cost investment for the faulted components in a system states sample of the transmission network; 2) a dynamic iterative approach that checks individually the investment’s effect on the transmission network. A case study using the Reliability Test System (RTS) 1996 IEEE 24 Buses is presented to illustrate in detail the application of the proposed methodology.

Fuzzy Monte Carlo mathematical model for load curtailment minimization in transmission power systems

This paper presents a methodology which is based on statistical failure and repair data of the transmission power system components and uses fuzzyprobabilistic modeling for system component outage parameters. Using statistical records allows developing the fuzzy membership functions of system component outage parameters. The proposed hybrid method of fuzzy set and Monte Carlo simulation based on the fuzzy-probabilistic models allows catching both randomness and fuzziness of component outage parameters. A network contingency analysis to identify any overloading or voltage violation in the network is performed once obtained the system states by Monte Carlo simulation. This is followed by a remedial action algorithm, based on optimal power flow, to reschedule generations and alleviate constraint violations and, at the same time, to avoid any load curtailment, if possible, or, otherwise, to minimize the total load curtailment, for the states identified by the contingency analysis. In order to illustrate the application of the proposed methodology to a practical case, the paper will include a case study for the Reliability Test System (RTS) 1996 IEEE 24 BUS.