Combined experimental powder X-ray diffraction and DFT data to obtain the lowest energy molecular conformation of friedelin

Friedelin molecular conformers were obtained by Density Functional Theory (DFT) and by ab initio structure determination from powder X-ray diffraction. Their conformers with the five rings in chair-chair-chair-boat-boat, and with all rings in chair, are energy degenerated in gas-phase according to DFT results. The powder diffraction data reveals that rings A, B and C of friedelin are in chair, and rings D and E in boat-boat, conformation. The high correlation values among powder diffraction data, DFT and reported single-crystal data indicate that the use of conventional X-ray diffractometer can be applied in routine laboratory analysis in the absence of a single-crystal diffractometer.

Dielectric spectroscopy and thermally stimulated discharge current in PEEK film

The complex permittivity of films of polyether ether ketone (PEEK) has been investigated over a wide range of frequency. There is no relaxation peak in the range of 1Hz to 10(5) Hz but in the low-frequency side (10-4 Hz) there is an evidence of a peak that also can be observed by thermally stimulated discharge current measurements. That peak is related with the glass transition temperature (Tg) of the polymer. The activation energy of the relaxation was found to be 0.44 eV, similar to that of several synthetic polymers. Space charges are important in the conduction mechanism as shown by discharging transient.

Synthesis, structural and morphological characterization of CeO2-ZnO nanosized powder systems from Pechini's method

This work reports on the investigation of nanosized CeO2-ZnO systems prepared by Pechini's method. The structural and morphological characterization of CeO2-ZnO systems as well as the characterization of CeO2 and ZnO separately, showed that the employed method result in powders with spheroidal particles whose size are in the range 30 - 200 nm, which is appropriate to provide homogeneous suspensions. The ZnO present in the prepared mixed oxides seems to increase particle size distribution and to influence the arrangement of the particles after powder dispersion.

Synthesis and characterization of Fe(III)-doped ceramic membranes of titanium dioxide and its application in photoelectrocatalysis of a textile dye

Pure and Fe(III)-doped TiO2 suspensions were prepared by the sol gel method with the use of titanium isopropoxide (Ti(OPri)4) as precursor material. The properties of doped materials were compared to TiO2 properties based on the characterization by thermal analysis (TG-DTA and DSC), X-ray powder diffractometry and spectroscopy measurements (FTIR). Both undoped and doped TiO2 suspensions were used to coat metallic substrate as a mean to make thin-film electrodes. Thermal treatment of the precursors at 400ºC for 2 h in air resulted in the formation of nanocrystalline anatase TiO2. The thin-film electrodes were tested with respect to their photocatalytic performance for degradation of a textile dye in aqueous solution. The plain TiO2 remains as the best catalyst at the conditions used in this report.

Spelar kön någon roll när man räddar världen? : kvinnor, kvinnligheter och messiasmyter i SF-film

Studien grundar sig på tanken att populärkulturen och dess uttrycksformer är viktiga att analysera närmare även när det gäller en förståelse av religion i dagens värld. Populärkulturen kan antas både spegla och påverka oss. Detta sker naturligtvis inte på ett enkelt sätt, men populärkulturen kan ändå anses vara med och forma hur vi ser på världen omkring oss och på fenomen som t.ex. religion och könsroller. Den genre Sjö valt att rikta in sig på, science fiction, är vald med tanke på hur denna genre tagit sig an både frågor om religion och genus och hur den även blir av betydelse för analyser av dagens värld. Studien riktar i första hand in sig på forskning kring frälsartemat i populärkulturen. Det delvis nya som tillförs forskningen är ett genusperspektiv. Istället för att rikta in sig på de oftast manliga messiasgestalterna ser studien således till den kvinnliga närvaron i berättelserna. För det första analyseras kvinnliga karaktärer i rollerna som kärleksobjekt och mödrar. Centrala frågor som tas upp i denna del av avhandlingen är de kvinnliga karaktärernas roll i förhållande till manliga messiasgestalter och messiasmyter i materialet. Andra frågor som behandlas är de kvinnliga karaktärernas tillgång till en religiös röst och religiöst ledarskap, samt en hurdan kvinnlighet de kan anses representera. För det andra ser studien närmare på frågan om vad som händer med messiasmyten när en kvinna istället för en man tillåts rädda världen. En jämförelse görs mellan manliga och kvinnliga messiasgestalter och vissa tydliga olikheter särskilt i relation till frågor om religiös makt presenteras. Sofia Sjös avhandling visar på problem när det gäller frågor om kvinnligt religiöst ledarskap som även kan relateras till attityder i dagens värld, men pekar också på hur traditionella framställningar av både messiasmyt och kvinnlighet utmanas och förändras i det undersökta materialet.

Segregation of powder mixtures in silos with particular reference to dry mineral-based construction materials

Segregering eller segregation är ett fenomen som kan förekomma inom olika områden av samhället. Inom samhällsvetenskaperna kan segregering definieras som det rumsliga åtskiljandet av befolkningsgrupper på urval av ras eller etniskt ursprung, kön, social härkomst, religion, ålder, yrke, osv. Segregering av befolkningsgrupper sker ofta mer eller mindre frivilligt och är motsatsen till integration. Inom partikelteknologi definieras segregering oftast som det rumsliga åtskiljandet av beståndsdelarna i en blandning av olika partiklar. Segregering sker då på urval av bl.a. partiklarnas storlek, densitet, form, elektrostatiska eller mekaniska egenskaper, och kan beskrivas som motsatsen till blandning. Segregeringsmekanismer används för att förklara hur och varför en partikelblandning segregerar samt vad slutresultatet i form av den rumsliga fördelningen av partiklarna blir till följd av att blandningen utsetts för en viss behandling. I denna avhandling har segregering av partikelblandningar och speciellt torra mineralbaserade byggmaterial (t.ex. murbruk) till följd av lagring i siloer studerats. Vid industriell produktion av mineralbaserade byggmaterial används siloer för korttidslagring av slutprodukterna precis innan förpackning. Segregering leder till kraftiga variationer i sammansättningen för partikelströmmen ut ur silon, vilket gör att slutprodukterna inte uppfyller kvalitetskraven och kan därmed inte säljas till kunder. Detta leder till arbetsam och dyr bearbetning (återcirkulation) av produkterna med påföljder för produktionsekonomin samt hållbara utvecklingen. I avhandlingen identifierades de väsentligaste segregeringsmekanismerna för torra mineralbaserade byggmaterial i siloer. Dessutom klargjordes effekterna av materialegenskaper, processbetingelser och siloparametrar. Slutligen behandlas möjliga åtgärder för minskning av partikelsegregering i siloer samt tillämpning av matematiska metoder för simulering av partikelflöden med hjälp av datorer.

Powder flow criteria for design of vertical silo walls

For design of vertical silos walls involving the storage of bulk solids to be safe and reliable, it is important knowing the largest possible number of variables such as: flow properties, silo geometry and pattern of flow desired. In order to validate the theories of flow prediction and design of conical hoppers, the flow properties of two bulk solids were determined, the theories of Jenike's flowability and Enstad and Walker for hopper design were analyzed and the results were compared with those experimentally obtained in a reduced model of a semicircular-section silo. Results show that Enstad theory for the hopper design is adequate to occur mass flow inside the silo, and for the sizing of the discharge outlet, the Walker's theory was closer to the appropriate than Jenike's theory, which was higher around 100% than the experimental hopper outlet.

Energy and raw material consumption analysis of powder bed fusion: case study: CNC machining and laser additive manufacturing

Laser additive manufacturing (LAM), known also as 3D printing, is a powder bed fusion (PBF) type of additive manufacturing (AM) technology used to manufacture metal parts layer by layer by assist of laser beam. The development of the technology from building just prototype parts to functional parts is due to design flexibility. And also possibility to manufacture tailored and optimised components in terms of performance and strength to weight ratio of final parts. The study of energy and raw material consumption in LAM is essential as it might facilitate the adoption and usage of the technique in manufacturing industries. The objective this thesis was find the impact of LAM on environmental and economic aspects and to conduct life cycle inventory of CNC machining and LAM in terms of energy and raw material consumption at production phases. Literature overview in this thesis include sustainability issues in manufacturing industries with focus on environmental and economic aspects. Also life cycle assessment and its applicability in manufacturing industry were studied. UPLCI-CO2PE! Initiative was identified as mostly applied exiting methodology to conduct LCI analysis in discrete manufacturing process like LAM. Many of the reviewed literature had focused to PBF of polymeric material and only few had considered metallic materials. The studies that had included metallic materials had only measured input and output energy or materials of the process and compared to different AM systems without comparing to any competitive process. Neither did any include effect of process variation when building metallic parts with LAM. Experimental testing were carried out to make dissimilar samples with CNC machining and LAM in this thesis. Test samples were designed to include part complexity and weight reductions. PUMA 2500Y lathe machine was used in the CNC machining whereas a modified research machine representing EOSINT M-series was used for the LAM. The raw material used for making the test pieces were stainless steel 316L bar (CNC machined parts) and stainless steel 316L powder (LAM built parts). An analysis of power, time, and the energy consumed in each of the manufacturing processes on production phase showed that LAM utilises more energy than CNC machining. The high energy consumption was as result of duration of production. Energy consumption profiles in CNC machining showed fluctuations with high and low power ranges. LAM energy usage within specific mode (standby, heating, process, sawing) remained relatively constant through the production. CNC machining was limited in terms of manufacturing freedom as it was not possible to manufacture all the designed sample by machining. And the one which was possible was aided with large amount of material removed as waste. Planning phase in LAM was shorter than in CNC machining as the latter required many preparation steps. Specific energy consumption (SEC) were estimated in LAM based on the practical results and assumed platform utilisation. The estimated platform utilisation showed SEC could reduce when more parts were placed in one build than it was in with the empirical results in this thesis (six parts).

Preclinical evaluation of the antidiabetic effect of Eugenia jambolana seed powder in streptozotocin-diabetic rats

The world is facing an explosive increase in the incidence of diabetes mellitus and cost-effective complementary therapies are needed. The effects of Eugenia jambolana, a household remedy for diabetes, were studied. Streptozotocin diabetic female albino Wistar rats weighing 150-200 g (N = 6) were fed E. jambolana seed powder (250, 500 or 1000 mg/kg) for 15 days. Diabetic rats fed 500 and 1000 mg/kg seed powder showed an increase in body weight on day 20 in relation to day 5 (6 ± 4.7, 9 ± 7.8 vs diabetic control -16 ± 7.1 g, P < 0.001), a decrease in fasting blood glucose (75 ± 11.9, 123 ± 14.4 vs diabetic control -34 ± 12.1 mg/dl, P < 0.001), a difference in post-treatment fasting and peak blood glucose (38 ± 11.9, 36 ± 14.2 vs diabetic control 78 ± 11.9 mg/dl, P < 0.001), and a difference in liver glycogen (50 ± 6.8, 52 ± 7.5 vs normal control 90 ± 6.6 µg/g of liver tissue, P < 0.001). Tri-terpenoids, tannins, gallic acid, and oxalic acid were the chemical constituents detected in E. jambolana seed. The best results were obtained with an oral dose of 500 mg/kg. Subacute toxicity studies with a single administration of 2.5 and 5.0 g/kg seed powder showed no mortality or abnormality. These data on the antidiabetic effect of E. jambolana seed are adequate for approval of phase 2 clinical trials to evaluate this seed powder as complementary therapy in type 2 and type 1 diabetes.

Metal additive manufacturing of internal flow channels with powder bed fusion processes

This thesis studies the advantages, disadvantages and possibilities of additive manufacturing in making components with internal flow channels. These include hydraulic components, components with cooling channels and heat exchangers. Processes studied in this work are selective laser sintering and selective laser melting of metallic materials. The basic principles of processes and parameters involved in the process are presented and different possibilities of internal channel manufacturing and flow improvement are introduced

Laser scribing of thin-film PV modules

This study is a literature review on laser scribing in monolithically interconnected thin-film PV modules, focusing on efficiency of modules based on absorber materials CIGS, CdTe and a-Si. In thin-film PV module manufacturing scribing is used to interconnect individual cells monolithically by P1, P2 and P3 scribes. Laser scribing has several advantages compared to mechanical scribing for this purpose. However, laser scribing of thin-films can be a challenging process and may induce efficiency reducing defects. Some of these defects can be avoided by improving optimisation or processing methods.

Antinutrients in the cassava (Manihot esculenta Crantz) leaf powder at three ages of the plant

In Brazil, the cassava leaf meal (CLM) has been used to strive against undernourishment because it is a high source of vitamins and minerals. However, the wide variation in the chemical composition of the different cultivars, as well as their antinutritional substances may be a restriction to their uses. The levels of some antinutrients in CLM from five cultivars at three ages of the plant (TAP) were investigated, in order to select the cultivars and plant ages that would be more appropriate for human consumption. The lowest contents of antinutrients were observed in the 12-month old plants, except for nitrate and hemagglutinin from which the lowest contents were found for the 17 month old ones. The cultivar IAC 289-70 had the lowest antinutrient levels, except for saponin and oxalate. Thus, the cultivar IAC 289-70 at 12 months is the most appropriate for human consumption.

Weldability of powder bed fusion fabricated stainless steel 316L sheets to cold rolled sheet metal

Weldability of powder bed fusion (PBF) fabricated components has come to discussion in past two years due to resent developments in the PBF technology and limited size of the machines used in the fabrication process. This study concentrated on effects of energy input of welding on mechanical properties and microstructural features of welds between PBF fabricated stainless steel 316L sheets and cold rolled sheet metal of same composition by the means of destructive testing and microscopic analysis. Optical fiber diameter, laser power and welding speed were varied during the experiments that were executed following one variable at a time (OVAT) method. One of the problems of welded PBF fabricated components has been lower elongations at break comparing to conventionally manufactured components. Decreasing energy input of the laser keyhole welding decreased elongations at break of the welded specimens. Ultimate tensile strengths were not affected significantly by the energy input of the welding, but fracturing of the specimens welded using high energy input occurred from the weld metal. Fracturing of the lower energy input welds occurred from the PBF fabricated base metal. Energy input was found to be critical factor for mechanical properties of the welds. Multioriented grain growth and formation of neck at fusion zone boundary on the cold rolled side of the weld was detected and suspected to be result from weld pool flows caused by differences in molten weld pool behaviour between the PBF fabricated and cold rolled sides of the welds.

Effect of drying method on the adsorption isotherms and isosteric heat of passion fruit pulp powder

The sorption behavior of dry products is generally affected by the drying method. The sorption isotherms are useful to determine and compare thermodynamic properties of passion fruit pulp powder processed by different drying methods. The objective of this study is to analyze the effects of different drying methods on the sorption properties of passion fruit pulp powder. Passion fruit pulp powder was dehydrated using different dryers: vacuum, spray dryer, vibro-fluidized, and freeze dryer. The moisture equilibrium data of Passion Fruit Pulp (PFP) powders with 55% of maltodextrin (MD) were determined at 20, 30, 40 and 50 ºC. The behavior of the curves was type III, according to Brunauer's classification, and the GAB model was fitted to the experimental equilibrium data. The equilibrium moisture contents of the samples were little affected by temperature variation. The spray dryer provides a dry product with higher adsorption capacity than that of the other methods. The vibro-fluidized bed drying showed higher adsorption capacity than that of vacuum and freeze drying. The vacuum and freeze drying presented the same adsorption capacity. The isosteric heats of sorption were found to decrease with increasing moisture content. Considering the effect of drying methods, the highest isosteric heat of sorption was observed for powders produced by spray drying, whereas powders obtained by vacuum and freeze drying showed the lowest isosteric heats of sorption.

Identification of fatty foods with contamination possibilities by plasticizers when stored in PVC film packaging

Poly-(vinyl chloride) (PVC) requires the addition of plasticizers - additives that give flexibility and malleability for its processing into flexible film. The most used ones are: di-(2-ethylhexyl) adipate (DEHA) and di-(2-ethylhexyl) phthalate (DEHP). Toxic effects of DEHP have been observed by several authors. Phthalates are being replaced by alternative substances in PVC flexible products, because of their possible toxicological effects. DEHA is a substitute for phthalates widely used as a plasticizer in PVC materials for involving food. Some authors have shown that the exposure to DEHA also induces toxicity. A cross-sectional study was performed to identify which fatty foods carry the possibility of contamination by DEHP and DEHA. Eighteen different foods with at least 3% (m/m) fat and the possibility of being wrapped in plastic film were determined. This study suggested that all foods were subject to contamination by DEHP and DEHA in those conditions - in decreasing consumption order of 96 to 22% in the convenience sample. New guidelines on the limits of DEHA and DEHP established by the Brazilian legislation, as additives in PVC film for packaging fatty food, are still relevant to ensure human health.