Changes in a Rhodic Hapludox under no-tillage and urban waste compost in the northwest of Rio Grande do Sul, Brazil

The use of urban waste compost as nutrient source in agriculture has been a subject of investigation in Brazil and elsewhere, although the effects on soil physical and chemical properties and processes are still poorly known. The aim of this study was to evaluate the effect of application of urban waste compost and mineral fertilizer on soil aggregate stability and organic carbon and total nitrogen content of a Rhodic Hapludox under no-tillage in the northwestern region of Rio Grande do Sul, Brazil, in the 2009/2010 and 2010/2011 growing seasons. The experiment was arranged in a 2 × 6 (seasons and fertilization) factorial in a randomized complete block design with four replications. The factor time consisted of two growing seasons (sunflower in 2009/10 and maize in 2010/11) and the factor fertilization of five rates of urban waste compost (0, 25, 50, 75 and 100 m³ ha-1), and mineral fertilizer. Soil samples were collected from the 0.0-0.10 m layer to determine aggregate stability (mean weight and geometric diameter), soil organic carbon (SOC) and total nitrogen (TN). Rates of up to 75 m³ ha-1 of urban waste compost, after two years of application to no-tillage maize and sunflower, improved aggregation compared to mineral fertilization in a Rhodic Hapludox. After the second crop, the SOC and TN contents increased linearly with the levels of urban waste compost.

Feed intake and growth performance of goats supplemented with soy waste

The objective of this work was to evaluate the effects of supplemental feeding of soy waste on the feed intake and growth rate of goats. Twenty male crossbred (Boer x local) goats were assigned to two isonitrogenous diet groups: one of commercial pellet and the other of soy waste. The commercial pellet (1.0%) and soy waste (0.8%) were provided on the dry matter basis of body weight (BW) per day, to the respective group of each diet. The soy waste group had lower daily intakes of total dry matter (0.79 vs. 0.88 kg) and organic matter (665.71 vs. 790.44 g) than the group fed pellet; however, the differences on daily intakes for grass (0.62 vs. 0.64 kg), crude protein (96.81 vs. 96.83 g), and neutral detergent fibre (483.70 vs. 499.86 g) were not significant. No differences were observed between groups for BW gain. The feed conversion ratio and feed cost per kilogram of BW gain were lower for the group fed soy waste than for the one fed pellet. Goats fed supplemental soy waste have a lower total dry matter intake, feed conversion ratio, and feed cost per kilogram of body weight gain than those fed commercial pellets.

Biochemical treatment of brown grade rejects in recycling process

Ruskeisiin kierrätysmassoihin kuuluu kulutuksen kannalta tärkeimpänä laatuna OCC (old corrugated containers). OCC sisältää noin 70-100% aaltopahvia eli pääasiassa se koostuu valkaisemattomasta kemiallisesta massasta. OCC uusiomassan ensisijainen käyttökohde on aaltopahvin valmistus. OCC:n kierrätyskuituprosessissa syntyy merkittäviä määriä rejektiä. Rejektin määrä riippuu paljolti kierrätettävän materiaalin laadusta ja puhtaudesta, mutta myös tulevan massan käyttötarkoituksesta sekä prosessiolosuhteista. OCC-prosessissa rejektoituvan aineksen määrä voi nousta korkeaksi, mikäli kierrätettävä materiaali sisältää märkälujaliimoja tai muuten raskaasti liimattuja komponentteja sekä runsaasti kontaminantteja, kuten muoveja, teippejä ja metalleja. Keskimäärin OCC-rejekti sisältää 30-60% kiinteää ainesta, 30-90% (kuivapaino) kuituja, 5-70% (kuivapaino) muoveja ja 1-10% (kuivapaino) tuhkaa. Syntynyt rejekti voidaan polttaa energiaksi tai käyttää maantäyttöaineena. Harvinaisempia sovelluksia rejektin käsittelyssä ovat rejektin kuitujen talteenotto uudelleenprosessointia varten tai alkoholin ja levuliinihapon tuottamiseen. Rejektin asianmukaisella käsittelyllä voidaan vähentää kaatopaikkakustannuksia, sekä parantaa kierrätysprosessin tuottavuutta. Tämän työn tarkoituksena oli tutkia biokemiallisen käsittelyn mahdollisuudet OCC-rejektin hajotuksessa. Alustavissa laboratoriomittakaavan kokeissa etsittiin sopiva käsittelytapa, joka toteutettiin sitten pilot plant -mittakaavassa. Tulokset osoittavat, että biokemiallisen käsittelyn avulla rejekti voidaan hajottaa jolloin jätteenkäsittelykustannukset pienenevät ja kierrätyskuituprosessin taloudellisuus paranee.

Effects of unit - based pricing on the waste collection demand : a meta - regression analysis

We perform a meta - analysis of 21 studies that estimate the elasticity of the price of waste collection demand upon waste quantities, a prior literature review having revealed that the price elasticity differs markedly. Based on a meta - regression with a total of 65 observations, we find no indication that municipal data give higher estimates for price elasticities than those associated with household data. Furthermore, there is no evidence that treating prices as exogenous underestimates the price elasticity. We find that much of the variation can be explained by sample size, the use of a weight - based as opposed to a volume - based pricing system, and the pricing of compostable waste. We also show that price elasticities determined in the USA and point estimations of elasticities are more elastic, but these effects are not robust to the changing of model specifications. Finally, our tests show that there is no evidence of publication bias while there is some evidence of the existence of genuine empirical effect.

Methods for assessing the sustainability of integrated municipal waste management and

The general striving to bring down the number of municipal landfills and to increase the reuse and recycling of waste-derived materials across the EU supports the debates concerning the feasibility and rationality of waste management systems. Substantial decrease in the volume and mass of landfill-disposed waste flows can be achieved by directing suitable waste fractions to energy recovery. Global fossil energy supplies are becoming more and more valuable and expensive energy sources for the mankind, and efforts to save fossil fuels have been made. Waste-derived fuels offer one potential partial solution to two different problems. First, waste that cannot be feasibly re-used or recycled is utilized in the energy conversion process according to EU’s Waste Hierarchy. Second, fossil fuels can be saved for other purposes than energy, mainly as transport fuels. This thesis presents the principles of assessing the most sustainable system solution for an integrated municipal waste management and energy system. The assessment process includes: · formation of a SISMan (Simple Integrated System Management) model of an integrated system including mass, energy and financial flows, and · formation of a MEFLO (Mass, Energy, Financial, Legislational, Other decisionsupport data) decision matrix according to the selected decision criteria, including essential and optional decision criteria. The methods are described and theoretical examples of the utilization of the methods are presented in the thesis. The assessment process involves the selection of different system alternatives (process alternatives for treatment of different waste fractions) and comparison between the alternatives. The first of the two novelty values of the utilization of the presented methods is the perspective selected for the formation of the SISMan model. Normally waste management and energy systems are operated separately according to the targets and principles set for each system. In the thesis the waste management and energy supply systems are considered as one larger integrated system with one primary target of serving the customers, i.e. citizens, as efficiently as possible in the spirit of sustainable development, including the following requirements: · reasonable overall costs, including waste management costs and energy costs; · minimum environmental burdens caused by the integrated waste management and energy system, taking into account the requirement above; and · social acceptance of the selected waste treatment and energy production methods. The integrated waste management and energy system is described by forming a SISMan model including three different flows of the system: energy, mass and financial flows. By defining the three types of flows for an integrated system, the selected factor results needed in the decision-making process of the selection of waste management treatment processes for different waste fractions can be calculated. The model and its results form a transparent description of the integrated system under discussion. The MEFLO decision matrix has been formed from the results of the SISMan model, combined with additional data, including e.g. environmental restrictions and regional aspects. System alternatives which do not meet the requirements set by legislation can be deleted from the comparisons before any closer numerical considerations. The second novelty value of this thesis is the three-level ranking method for combining the factor results of the MEFLO decision matrix. As a result of the MEFLO decision matrix, a transparent ranking of different system alternatives, including selection of treatment processes for different waste fractions, is achieved. SISMan and MEFLO are methods meant to be utilized in municipal decision-making processes concerning waste management and energy supply as simple, transparent and easyto- understand tools. The methods can be utilized in the assessment of existing systems, and particularly in the planning processes of future regional integrated systems. The principles of SISMan and MEFLO can be utilized also in other environments, where synergies of integrating two (or more) systems can be obtained. The SISMan flow model and the MEFLO decision matrix can be formed with or without any applicable commercial or free-of-charge tool/software. SISMan and MEFLO are not bound to any libraries or data-bases including process information, such as different emission data libraries utilized in life cycle assessments.

TREATMENT OF WASTE FROM ATOMIC EMISSION SPECTROMETRIC TECHNIQUES AND REUSE IN UNDERGRADUATE LAB CLASSES FOR QUALITATIVE ANALYSIS

Flame atomic absorption spectrometry (FAAS) and inductively coupled plasma optical emission spectrometry (ICP OES) are widely used in academic institutions and laboratories for quality control to analyze inorganic elements in samples. However, these techniques have been observed to underperform in sample nebulization processes. Most of the samples processed through nebulization system are discarded, producing large volumes of waste. This study reports the treatment and reuse of the waste produced from ICP OES technique in a laboratory of analytical research at the Universidade Federal do Ceará, Brazil. The treatment of the waste was performed by the precipitation of elements using (NH4)2CO3. Subsequently, the supernatant solution can be discarded in accordance with CONAMA 430/2011. The precipitate produced from the treatment of residues can be reused as a potential sample in undergraduate qualitative analytical chemistry lab classes, providing students the opportunity to test a real sample.

Integration of the Food Waste Disposer Unit to the Existing Sewage System

Among the numerous approaches to food waste treatment, the food waste disposers method (FWDs), as a newcomer, has become slowly accepted by the general public owing to the worries about its impact on the existing sewage system. This paper aims to justify the role of FWDs in the process of urbanization in order to better prepare a city to take good care of the construction of its infrastructure and the solid waste treatment. Both the literatures and the case study help to confirm that FWDs has no negative effects on the wastewater treatment plant and it is also environmental friendly by reducing the greenhouse gas emissions. In the case study, the Lappeenranta waste water treatment plant has been selected in order to figure out the possible changes to a WWTP following the integration of FWDs: the observation shows only minor changes take place in a WWTP, in case of 25% application, like BOD up 7%, TSS up 6% and wastewater flowrate up 6%, an additional sludge production of 200 tons per year and the extra yield of methane up to 10000m3 per year; however, when the utilization rate of FWD is over 75%, BOD, TSS, and wastewater flowrate will experience more significant changes, thus exerting much pressure on the existing WWTP. FWDs can only be used in residential areas or cities equipped with consummate drainage network within the service sphere of WWTP, therefore, the relevant authority or government department should regulate the installation frequency of FWDs, while promoting the accessory application of FWDs. In the meanwhile, WWTP should improve their treatment process in order to expand their capacity for sludge treatment so as to stay in line with the future development of urban waste management.

Characterisation of waste for combustion : with special reference to the role of zinc

Waste combustion has gone from being a volume reducing discarding-method to an energy recovery process for unwanted material that cannot be reused or recycled. Different fractions of waste are used as fuel today, such as; municipal solid waste, refuse derived fuel, and solid recovered fuel. Furthermore, industrial waste, normally a mixture between commercial waste and building and demolition waste, is common, either as separate fuels or mixed with, for example, municipal solid waste. Compared to fossil or biomass fuels, waste mixtures are extremely heterogeneous, making it a complicated fuel. Differences in calorific values, ash content, moisture content, and changing levels of elements, such as Cl and alkali metals, are common in waste fuel. Moreover, waste contains much higher levels of troublesome trace elements, such as Zn, which is thought to accelerate a corrosion process. Varying fuel quality can be strenuous on the boiler system and may cause fouling and corrosion of heat exchanger surfaces. This thesis examines waste fuels and waste combustion from different angles, with the objective of giving a better understanding of waste as an important fuel in today’s fuel economy. Several chemical characterisation campaigns of waste fuels over longer time periods (10-12 months) was used to determine the fossil content of Swedish waste fuels, to investigate possible seasonal variations, and to study the presence of Zn in waste. Data from the characterisation campaigns were used for thermodynamic equilibrium calculations to follow trends and determine the effect of changing concentrations of various elements. The thesis also includes a study of the thermal behaviour of Zn and a full—scale study of how the bed temperature affects the volatilisation of alkali metals and Zn from the fuel. As mixed waste fuel contains considerable amounts of fresh biomass, such as wood, food waste, paper etc. it would be wrong to classify it as a fossil fuel. When Sweden introduced waste combustion as a part of the European Union emission trading system in the beginning of 2013 there was a need for combustion plants to find a usable and reliable method to determine the fossil content. Four different methods were studied in full-scale of seven combustion plants; 14Canalysis of solid waste, 14C-analysis of flue gas, sorting analysis followed by calculations, and a patented balance method that is using a software program to calculate the fossil content based on parameters from the plant. The study showed that approximately one third of the coal in Swedish waste mixtures has fossil origins and presented the plants with information about the four different methods and their advantages and disadvantages. Characterisation campaigns also showed that industrial waste contain higher levels of trace elements, such as Zn. The content of Zn in Swedish waste fuels was determined to be approximately 800 mg kg-1 on average, based on 42 samples of solid waste from seven different plants with varying mixtures between municipal solid waste and industrial waste. A review study of the occurrence of Zn in fuels confirmed that the highest amounts of Zn are present in waste fuels rather than in fossil or biomass fuels. In tires, Zn is used as a vulcanizing agent and can reach concentration values of 9600-16800 mg kg-1. Waste Electrical and Electronic Equipment is the second Zn-richest fuel and even though on average Zn content is around 4000 mg kg-1, the values of over 19000 mg kg-1 were also reported. The increased amounts of Zn, 3000-4000 mg kg-1, are also found in municipal solid waste, sludge with over 2000 mg kg-1 on average (some exceptions up to 49000 mg kg-1), and other waste derived fuels (over 1000 mg kg-1). Zn is also found in fossil fuels. In coal, the average level of Zn is 100 mg kg-1, the higher amount of Zn was only reported for oil shale with values between 20-2680 mg kg-1. The content of Zn in biomass is basically determined by its natural occurrence and it is typically 10-100 mg kg-1. The thermal behaviour of Zn is of importance to understand the possible reactions taking place in the boiler. By using thermal analysis three common Zn-compounds were studied (ZnCl2, ZnSO4, and ZnO) and compared to phase diagrams produced with thermodynamic equilibrium calculations. The results of the study suggest that ZnCl2(s/l) cannot exist readily in the boiler due to its volatility at high temperatures and its conversion to ZnO in oxidising conditions. Also, ZnSO4 decomposes around 680°C, while ZnO is relatively stable in the temperature range prevailing in the boiler. Furthermore, by exposing ZnO to HCl in a hot environment (240-330°C) it was shown that chlorination of ZnO with HCl gas is possible. Waste fuel containing high levels of elements known to be corrosive, for example, Na and K in combination with Cl, and also significant amounts of trace elements, such as Zn, are demanding on the whole boiler system. A full-scale study of how the volatilisation of Na, K, and Zn is affected by the bed temperature in a fluidised bed boiler was performed parallel with a lab-scale study with the same conditions. The study showed that the fouling rate on deposit probes were decreased by 20 % when the bed temperature was decreased from 870°C to below 720°C. In addition, the lab-scale experiments clearly indicated that the amount of alkali metals and Zn volatilised depends on the reactor temperature.

Importance of considering food waste in the development of sustainable food packaging systems

Meeting the needs of both present and future generations forms the foundation of sustainable development. Concern about food demand is increasing alongside the continuously growing population. In the pursuit of food security preventing food waste is one solution avoiding the negative environmental impacts that result from producing food unnecessarily. Packages offer one answer to preventing food waste, as they 1) preserve and protect food, 2) introduce the user to the correct way to handle and use the food and package and 3) allow the user to consume the food in its entirety. This thesis aims to enhance the sustainability of food packages by giving special emphasis to preventing food waste. The focus of this thesis is to assist the packaging designer in being able to take into account the requirements for the sustainability of food packages and to be able to integrate these requirements into the product development process. In addition, life cycle methods that can be used as a tool in the packaging design process or in assessing the sustainability of finished food-packaging combinations are evaluated. The methods of life cycle costing (LCC) and life cycle working environment (LCWE) are briefly discussed. The method of life cycle assessment (LCA) is examined more thoroughly through the lens of the literature review of food-package LCA case studies published in the 21st century in three relevant journals. Based on this review and on experiences learned from conducting LCAs, recommendations are given as to how the LCA practitioner should conduct a food packaging study to make most of the results. Two case studies are presented in this thesis. The first case study relates the results of a life cycle assessment conducted for three food items (cold cut (ham), sliced dark bread (rye) and Soygurt drink) and the alternative packaging options of each. Results of this study show that the packaging constitutes only 1–12 % of the total environmental impacts of the food-packaging combination. The greatest effect is derived from the food itself and the wasted food. Even just a small percentage of wasted food causes more environmental impacts than does the packaging. The second case study presents the results of LCC and LCWE analysis done for fruit and vegetable transport packages. In this thesis, the specific results of the study itself are not the focus, but rather the study methods and scope are analysed based on how these complement the sustainability assessment of food packages. This thesis presents reasons why prevention of food waste should be more thoroughly taken into account in food packaging design. In addition, the task of the packaging designer is facilitated by the requirements of sustainable food packaging, by the methods and step-by-step guidance on how to integrate sustainability issues into the design process, and by the recommendations on how to assess the sustainability of food packages. The intention of this thesis is to express the issues that are important in the field of the food packaging industry. Having recognised and implemented these issues, businesses can better manage the risks that could follow from neglecting these sustainability aspects.

Microbiological and physicochemical characterization of surimi obtained from waste of piramutaba fillet

The aim of this work was to perform the microbiological and physicochemical characterization of surimi made from waste of piramutaba filleting. The results of physicochemical characterization of the waste and surimi were: moisture (76.37 and 79.11%), total lipids (5.35 and 0.74%), proteins (14.92 and 10.79%), ash (3.03 and 2.35%), pH (6.9 and 7.4), caloric value (109.15 and 77.86 kcal.g-1), and water activity (both 0.98), respectively. The results of the levels of total volatile bases were 7.29 mgN/100-1 g (waste) and 7.01% carbohydrate (surimi). The values of total lipids and proteins were reduced during the preparation of surimi, probably due to successive washes during the processing. Waste and surimi were examined microbiologically and are in compliance with required parameters. The results show a loss of red (a* parameter) and yellow (b* parameter) color. On the other hand, the L* parameter (lightness) increased after the processing of surimi. It can be concluded that piramutaba waste can be used for surimi preparation and as a source of nutrients for human consumption, providing an alternative use of these wastes avoiding their disposal polluting the environment.

Production of magnesium carbonates from serpentinites for CO2 mineral sequestration : optimisation towards industrial application

Global warming is one of the most alarming problems of this century. Initial scepticism concerning its validity is currently dwarfed by the intensification of extreme weather events whilst the gradual arising level of anthropogenic CO2 is pointed out as its main driver. Most of the greenhouse gas (GHG) emissions come from large point sources (heat and power production and industrial processes) and the continued use of fossil fuels requires quick and effective measures to meet the world’s energy demand whilst (at least) stabilizing CO2 atmospheric levels. The framework known as Carbon Capture and Storage (CCS) – or Carbon Capture Utilization and Storage (CCUS) – comprises a portfolio of technologies applicable to large‐scale GHG sources for preventing CO2 from entering the atmosphere. Amongst them, CO2 capture and mineralisation (CCM) presents the highest potential for CO2 sequestration as the predicted carbon storage capacity (as mineral carbonates) far exceeds the estimated levels of the worldwide identified fossil fuel reserves. The work presented in this thesis aims at taking a step forward to the deployment of an energy/cost effective process for simultaneous capture and storage of CO2 in the form of thermodynamically stable and environmentally friendly solid carbonates. R&D work on the process considered here began in 2007 at Åbo Akademi University in Finland. It involves the processing of magnesium silicate minerals with recyclable ammonium salts for extraction of magnesium at ambient pressure and 400‐440⁰C, followed by aqueous precipitation of magnesium in the form of hydroxide, Mg(OH)2, and finally Mg(OH)2 carbonation in a pressurised fluidized bed reactor at ~510⁰C and ~20 bar PCO2 to produce high purity MgCO3. Rock material taken from the Hitura nickel mine, Finland, and serpentinite collected from Bragança, Portugal, were tested for magnesium extraction with both ammonium sulphate and bisulphate (AS and ABS) for determination of optimal operation parameters, primarily: reaction time, reactor type and presence of moisture. Typical efficiencies range from 50 to 80% of magnesium extraction at 350‐450⁰C. In general ABS performs better than AS showing comparable efficiencies at lower temperature and reaction times. The best experimental results so far obtained include 80% magnesium extraction with ABS at 450⁰C in a laboratory scale rotary kiln and 70% Mg(OH)2 carbonation in the PFB at 500⁰C, 20 bar CO2 pressure for 15 minutes. The extraction reaction with ammonium salts is not at all selective towards magnesium. Other elements like iron, nickel, chromium, copper, etc., are also co‐extracted. Their separation, recovery and valorisation are addressed as well and found to be of great importance. The assessment of the exergetic performance of the process was carried out using Aspen Plus® software and pinch analysis technology. The choice of fluxing agent and its recovery method have a decisive sway in the performance of the process: AS is recovered by crystallisation and in general the whole process requires more exergy (2.48–5.09 GJ/tCO2sequestered) than ABS (2.48–4.47 GJ/tCO2sequestered) when ABS is recovered by thermal decomposition. However, the corrosive nature of molten ABS and operational problems inherent to thermal regeneration of ABS prohibit this route. Regeneration of ABS through addition of H2SO4 to AS (followed by crystallisation) results in an overall negative exergy balance (mainly at the expense of low grade heat) but will flood the system with sulphates. Although the ÅA route is still energy intensive, its performance is comparable to conventional CO2 capture methods using alkanolamine solvents. An energy‐neutral process is dependent on the availability and quality of nearby waste heat and economic viability might be achieved with: magnesium extraction and carbonation levels ≥ 90%, the processing of CO2‐containing flue gases (eliminating the expensive capture step) and production of marketable products.

Fermentation of Prawn Shell Waste and Its Application of its Product as Dietary Ingredient for Penaeus Indicus (H. Milne Edwards)

This work envisages the fermentation of prawn shell waste into a more nutritious product with simpler components for application as a feed ingredient in aquaculture. This product would be a rich source of protein along with chitin, minerals, vitamins and N-acetyl glucosamine. A brief description of the various processing (chemical and bioprocess) methods employed for chitin, chitosan and single sell protein preparations from shell waste. It deals with the isolation of micro flora associated with prawn shell degradation. It describes the methods adopted for fermentation of prawn shell degradation and fermentation of prawn shell waste with the selected highly chitinoclastic strains. The comparison of SSF and SmF for each selected strain in terms of enrichment of protein, lipid and carbohydrate in the fermented product was done. Detailed analysis of product quality is discussed. The feed for mulation and feeding experiment explained in detail. Statistical analysis of various biogrowth parameters was done with Duncan’s multiple range test. Very briefly explains 28 days of feeding experiment. A method for the complete utilization of shell waste explains with the help of experiments.

Production of Alkaline Protease by Free and Immobilised Cells of VIBRIO sp. Under Different Fermentation Systems and Its Application on Deproteinisation of Prawn Shell Waste for Chitin Recovery

This thesis presents a detailed account of a cost - effective approach towards enhanced production of alkaline protease at profitable levels using different fermentation designs employing cheap agro-industrial residues. It involves the optimisation of process parameters for the production of a thermostable alkaline protease by Vibrio sp. V26 under solid state, submerged and biphasic fermentations, production of the enzyme using cell immobilisation technology and the application of the crude enzyme on the deproteinisation of crustacean waste.The present investigation suggests an economic move towards Improved production of alkaline protease at gainful altitudes employing different fermentation designs utilising inexpensive agro-industrial residues. Moreover, the use of agro-industrial and other solid waste substrates for fermentation helps to provide a substitute in conserving the already dwindling global energy resources. Another alternative for accomplishing economically feasible production is by the use of immobilisation technique. This method avoids the wasteful expense of continually growing microorganisms. The high protease producing potential of the organism under study ascertains their exploitation in the utilisation and management of wastes. However, strain improvement studies for the production of high yielding variants using mutagens or by gene transfer are required before recommending them to Industries.Industries, all over the world, have made several attempts to exploit the microbial diversity of this planet. For sustainable development, it is essential to discover, develop and defend this natural prosperity. The Industrial development of any country is critically dependent on the intellectual and financial investment in this area. The need of the hour is to harness the beneficial uses of microbes for maximum utilisation of natural resources and technological yields. Owing to the multitude of applications in a variety of industrial sectors, there has always been an increasing demand for novel producers and resources of alkaline proteases as well as for innovative methods of production at a commercial altitude. This investigation forms a humble endeavour towards this perspective and bequeaths hope and inspiration for inventions to follow.

Solid Waste Management: A Case Study of Arppukara Grama Panchayat Of Kottayam District, Kerala (India)

The rising pressure of Population, together with the constantly changing technologies, and development perspectives, contribute to the ever increasing volumes of wastes in different forms. The solid and liquid wastes generated in the urban areas were considered a burden to the society, and hazardous to the environment. The fact is that the growth of consumerist culture and aimless throwing of refuse by the people created the outbreak of environmental pollution. Unhygienic environment and solid waste accumulation coincided with mosquito breeding which causes, the spread of most epidemics. The rationale behind most of the diseases is the unhygienic pattern followed by the people both in rural and urban areas. As an environmental package, the disposal of solid waste from different sources, such as house holds markets, commercial areas, slaughter houses, hospitals and industries, therefore assumed crucial importance. So as a part of the theory and practice, a study on the area, solid waste management of Arppukara Grama Panchayat of Kottayam district is taken into consideration. The study conducted here proposes, to examine the quality and quantity of the solid waste generated in the panchayat and also it's impact on the existing social, economical, environmental and ecological systems

Utilization of waste expanded polystyrene: Blends with silica-filled natural rubber

Expanded polystyrene (EPS) constitutes a considerable part of thermoplastic waste in the environment in terms of volume. In this study, this waste material has been utilized for blending with silica-reinforced natural rubber (NR). The NR/EPS (35/5) blends were prepared by melt mixing in a Brabender Plasticorder. Since NR and EPS are incompatible and immiscible a method has been devised to improve compatibility. For this, EPS and NR were initially grafted with maleic anhydride (MA) using dicumyl peroxide (DCP) to give a graft copolymer. Grafting was confirmed by Fourier Transform Infrared Spectroscopy (FTIR) spectroscopy. This grafted blend was subsequently blended with more of NR during mill compounding. Morphological studies using Scanning Electron Microscopy (SEM) showed better dispersion of EPS in the compatibilized blend compared to the noncompatibilized blend. By this technique, the tensile strength, elongation at break, modulus, tear strength, compression set and hardness of the blend were found to be either at par with or better than that of virgin silica filled NR compound. It is also noted that the thermal properties of the blends are equivalent with that of virgin NR. The study establishes the potential of this method for utilising waste EPS