933 resultados para Perdas comerciais
Resumo:
In the last decades there was a significant increasing of the numbers of researchers that joint efforts to find alternatives to improve the development of low environmental impact technology. Materials based on renewable resources have enormous potentials of applications and are seen as alternatives for the sustainable development. Within other parameters, the sustainability depends on the energetic efficiency, which depends on the thermal insulation. Alternative materials, including vegetal fibers, can be applied to thermal insulation, where its first goal is to minimize the loss of energy. In the present research, it was experimentally analyzed the thermal behavior of fiber blankets of sisal (Agave sisalana) with and without surface treatment with oxide hidroxide (NaOH). Blankets with two densities (1100/1200 and 1300/1400 g/m2) were submitted to three rates of heat transfer (22.5 W, 40 W and 62.5 W). The analysis of the results allowed comparing the blankets treated and untreated in each situation. Others experiments were carried out to obtain the thermal conductivity (k), heat capacity (C) and the thermal diffusivity (α) of the blankets. Thermo gravimetric analyses were made to the verification of the thermal stability. Based on the results it was possible to relate qualitatively the effect of the heat transfer through the sisal blankets subjected to three heat transfer rates, corresponding to three temperature values (77 °C, 112 °C e 155 °C). To the first and second values of temperature it was verified a considerable reduction on the rate of heat transfer; nevertheless, to the third value of temperature, the surface of the blankets (treated and untreated) in contact with the heated surface of the tube were carbonized. It was also verified, through the analyses of the results of the measurements of k, C e α, that the blankets treated and untreated have values near to the conventional isolating materials, as glass wool and rock wool. It could be concluded that is technically possible the use of sisal blankets as constitutive material of thermal isolation systems in applications where the temperature do not reach values greater than 112 ºC
Resumo:
The use of reflective surfaces functioning as thermal insulator has grown significantly over the years. Reflective thermal insulator are materials that have several characteristics such as low emissivity, low absorptivity and high reflectivity in the infrared spectrum. The use of these materials has grown a lot lately, since it contains several important radioactive properties that minimize the heat loss of thermal systems and cooling systems that are used to block the heat on the roof of buildings. A system made of three surfaces of 316 stainless steel mirror was built to analyze the influence of reflective surfaces as a way to reduce the heat loss and thereby conserve the energy of a thermal system. The system was analyzed both with and without the presence of vacuum, and then compared with a system that contained glass wool between the stainless steel mirror walls, since this isolator is considered resistive and also broadly used around the world in thermal systems. The reflectivity and emissivity of the surfaces used were also measured in this experiment. A type K thermocouple was fixed on the wall of the system to obtain the temperature of the stainless steel mirror surfaces and to analyze the thermal behavior of each configuration used. The results showed an efficiency of 13% when the reflective surfaces were used to minimize the heat loss of the thermal system. However, the system with vacuum had the best outcome, a 60% efficiency. Both of these were compared to the system made of glass wool as a thermal insulator
Resumo:
Muitos patógenos, principalmente fungos, ocorrem em várias espécies de eucalipto, desde a fase de viveiro até os plantios adultos. Dentre as doenças fúngicas, destaca-se a mancha de micosferela, considerada uma das principais doenças, e o Eucalyptus globulus, uma das espécies mais suscetíveis. Esta doença é causada por várias espécies pertencentes aos gêneros Teratosphaeria e Mycosphaerella, sendo T. nubilosa de maior importância. O objetivo do presente estudo foi verificar a presença do fungo T.nubilosa em materiais coletados nos seguintes locais: Bagé-RS, Pedras Altas-RS, Botucatu-SP, Jacareí- SP e Itapeva-SP. Por meio de isolamentos a partir de folhas de E. globulus apresentando mancha de micosferela, foi possível a obtenção de isolados do fungo. A observação quanto ao padrão de germinação dos ascósporos, o seu crescimento micelial, e também por meio de PCR com primers da região genômica ITS1 e ITS4 e sequenciamento, e submissão ao GenBank, foi possível a determinação do gênero e da espécie do patógeno como T. nubilosa. Nos cinco locais estudados foi confirmada a presença deste agente causal de mancha de micosferela em plantios de E. globulus nas regiões Sul e Sudeste do Brasil.
Resumo:
No Brasil, a cotonicultura localiza-se em regiões onde o índice de precipitação pluvial é de aproximadamente 2.000 mm anuais. A aplicação de reguladores de crescimento em condições com esse índice faz com que o produto aplicado seja lavado antes de ser absorvido pelas plantas. O objetivo deste trabalho foi avaliar o efeito da lavagem do cloreto de mepiquat aplicado no algodoeiro, por chuvas simuladas em diferentes períodos após a aplicação do produto. O trabalho foi realizado em casa de vegetação, utilizando vasos de 12 L, com três plantas da cultivar DeltaOpal. No aparecimento do primeiro botão floral, aplicou-se cloreto de mepiquat na dose de 12,5 g ha-1 de i.a. Os tratamentos consistiram de duas lâminas de chuva, 10 e 20 mm, a 0, 2, 4, 8, 16 e 32 horas após aplicação do produto e sem chuva, com quatro repetições. Uma chuva de 10 mm foi suficiente para lavar o produto das folhas independentemente do tempo de ocorrência após a aplicação do regulador. Se houver ocorrência de chuva 0, 2, 4, 8, 16 e 32 horas após a aplicação do produto, a reposição deve ser de 131, 125, 120, 110, 93 e 70 mL ha-1, respectivamente.
Resumo:
O objetivo do presente trabalho foi verificar a resistência ao nematóide Meloidogyne mayaguensis em oito porta-enxertos de tomateiro considerados resistentes à Meloidogyne incognita, M. javanica e M. arenaria, comercializados no Brasil. Os porta-enxertos testados foram: 'Guardião', 'Helper-M', 'Anchor-T', 'Dr. K', 'Kagemuscha', 'TMA 809', 'Magnet' e 'He-Man'. O experimento constou de 9 tratamentos (8 porta-enxertos e a cultivar Rutgers utilizada como padrão de suscetibilidade), com 6 repetições, sendo cada parcela constituída por 1 planta por vaso, mantidas em casa de vegetação. As plantas foram inoculadas com 5.000 ovos e eventuais juvenis infectantes de M. mayaguensis. O experimento seguiu o delineamento inteiramente casualizado. Aos 60 dias da inoculação procederam-se as avaliações, quando foram avaliados os índices de galhas e massas de ovos, número de nematóides no solo e na raiz, peso do sistema radicular e o fator de reprodução. Todos os porta-enxertos estudados demonstraram-se suscetíveis a M. mayaguensis.
Resumo:
Com o objetivo de avaliar a influência da assistência de ar na deposição da calda de pulverização, em plantas de feijoeiro (Phaseolus vulgaris) aos 26 dias após a emergência (DAE), com pontas de pulverização de jato cônico vazio (JA-0,5 e JA-1) e jato plano (AXI-110015), e volumes de calda, foi realizado um experimento em delineamento inteiramente casualizado, utilizando como traçador o íon cobre. Alvos coletores (papel de filtro com 3 x 3 cm) foram afixados nas superfícies adaxial e abaxial de folíolos posicionados nas partes superior e inferior das plantas. Para aplicar a solução traçadora, utilizou-se pulverizador com barras de 14 metros, com e sem assistência de ar, volumes de 60 e 100 L.ha-1, e velocidade do ar correspondente a 50% da rotação máxima do ventilador. Após a aplicação, os coletores foram lavados individualmente em solução extratora de ácido nítrico a 1,0 mol.L-1, e a quantificação dos depósitos através de espectrofotometria. A assistência de ar não influenciou na deposição da calda tanto a 60 quanto a 100 L.ha-1. O maior volume proporcionou maiores depósitos, sendo constatadas elevadas perdas para o solo (mais de 60%).
Resumo:
The increasing demand for energy and the environment consequences derived from the use of fossil energy, beyond the future scarcity of the oil that currently is the main power plant of the world, it stimulated the research around the production of biodiesel. In this work the synthesis of biodiesel of cotton in the methyl route was carried through, for had been in such a way used catalyst commercial homogeneous, Na-Methylat and the K-Methylat, aiming to the evaluation of the efficiency of them. An experimental planning 23 was elaborated aiming to evaluate the influence of the variable (molar reason oil/alcohol, % of catalyst and temperature) in the process as well as indicating the excellent point of operation in each case. The biodiesel was analyzed by gaseous chromatography, indicating a conversion of 96,79% when used Na-Methylat® as catalytic, and 95,65% when the K-Methylat® was used. Optimum result found with regard to the conversion was obtained at the following conditions: molar reason oil/alcohol (1:8), temperature of 40°C and 1% of catalyst Na-Methylat, reaching a 96,79% conversion, being, therefore, above of the established for the European norm (96.5%). The analysis of regression showed that the only significant effect for a confidence level of 95%, was of the changeable temperature. The variance analysis evidenced that the considered model is fitted quite to the experimental response, being statistically significant; however it does not serve inside for make forecasts of the intervals established for each variable. The best samples were analyzed by infra-red (IR) that identified the strong bands of axial deformation C=O of methylic ester, characterized through analyses physicochemical that had indicated conformity with the norms of the ANP, that with the thermal and rheological analyses had together evidenced that biodiesel can be used as combustible alternative in substitution to diesel
Resumo:
Steam assisted gravity drainage process (SAGD) involves two parallel horizontal wells located in a same vertical plane, where the top well is used as steam injector and the bottom well as producer. The dominant force in this process is gravitational. This improved oil recovery method has been demonstrated to be economically viable in commercial projects of oil recovery for heavy and extra heavy oil, but it is not yet implemented in Brazil. The study of this technology in reservoirs with characteristics of regional basins is necessary in order to analyze if this process can be used, minimizing the steam rate demand and improving the process profitability. In this study, a homogeneous reservoir was modeled with characteristics of Brazilian Northeast reservoirs. Simulations were accomplished with STARS , a commercial software from Computer Modelling Group, which is used to simulate improved oil recovery process in oil reservoirs. In this work, a steam optimization was accomplished in reservoirs with different physical characteristics and in different cases, through a technical-economic analysis. It was also studied a semi-continuous steam injection or with injection stops. Results showed that it is possible to use a simplified equation of the net present value, which incorporates earnings and expenses on oil production and expenses in steam requirement, in order to optimize steam rate and obtaining a higher net present value in the process. It was observed that SAGD process can be or not profitable depending on reservoirs characteristics. It was also obtained that steam demand can still be reduced injecting in a non continuous form, alternating steam injection with stops at several time intervals. The optimization of these intervals allowed to minimize heat losses and to improve oil recovery
Resumo:
To prevent large errors in the GPS positioning, cycle slips should be detected and corrected. Such procedure is not trivial, mainly for single frequency receivers, but normally it is not noticed by the users. Thus, it will be discussed some practical and more used methods for cycle slips detection and correction using just GPS single-frequency observations. In the detection, the triple (TD) and tetra differences were used. In relation to the correction, in general, each slip is corrected in the preprocessing. Otherwise, other strategies should be adopted during the processing. In this paper, the option was to the second option, and two strategies were tested. In one of them, the elements of the covariance matrix of the involved ambiguities are modified and new ambiguity estimation starts. In the one, a new ambiguity is introduced as additional unknown when a cycle slip is detected. These possibilities are discussed and compared in this paper, as well as the aspects related to the practicity, implementation and viability of each one. Some experiments were carried out using simulated data with cycle slips in different satellites and epochs of the data. This allowed assessing and comparing the results of different occurrence of cycle slip and correction in several conditions.
Resumo:
For a complete comprehension of the effect of tooth loss is necessary to listen to the patients that have it. This study, of qualitative approach, investigate, in the dental history of users of SUS, listening to his/her experiences with the services of dental care, the reason that lead his/her to dental lost and the repercussion of this in his/her life. The collect of data was made by narrative interview, obeying to a pre-defined schema. The subjects interviewed were six (three of urban zone and three of rural zone), all of them were users of Family Health Units. The criterions of inclusion were the followings: the presence of tooth lost (total lost in both dental arch or in one of them, or partial lost in at least six elements in one of the arches); age between 25 and 59; male or female; to live in municipal district of São Tomé/RN or Natal/RN. Based on previous interviews was elaborated the odontological history of each patient. Such narratives, systemized in odontological history, were analyzed taking as base the studies of Souza71 and the proposal of Schutze, suggested for Jovchelovitch, Bauer34. The results show that toothache was the main reason for the search of odontological care. The patients confront the ache with home-made medicaments, allopathic ones, and searching for dental care. The searching for exodontics was stimulated for geographic access difficulties or for repressed demand, which as a result produced the aggravation of the lesions and the discredit in restoration s treatment. The self-care practice of tooth-brush with juá or toothpaste and the controlled ingestion of sugar was not sufficient to avoid dental lost. Guilty sentiments were identified in relation with lack of care with teeth. The acceptance of dental lost as a natural factor is an important motivation in lack of pain and in the belief that it was a simple part of life in old age. Life with dental prosthesis makes clear the difference between which was natural and which was unnatural, and difficulties with the prosthesis appeared. The limitation of the prosthesis in its functional aspect can be compensated by esthetic restitution, making possible smiling expression. Starting with this study and considering the high number of dental lost, mainly in low-rent population, which live with toothless limitations or bad-quality prosthesis which do not rehabilitate adequately, we suggested the realization of qualitative researches which include, also, another actors in heath care services such as professionals and administrators
Resumo:
The objective of this study was to evaluate the quality of housing and the physical and chemical characteristics of meat from sheep raised on pasture Brachiaria brizantha and Panicum maximum. The experiment was conducted in the physical area of the Study Group on Forage (GEFOR), located in the Academic Unit Specialized in Agricultural Sciences - Federal University of Rio Grande do Norte - UFRN in Macaíba, RN, Brazil. We used 32 lambs SPRD, obtained from herds in the state, with liveweight (LW) of 24.5 kg were assigned randomly to four treatments consisting of tropical grasses, two cultivars of Brachiaria brizantha, Marandu and Piatã, and two of Panicum maximum, Aruana and Massai. The experimental area was 2.88 ha, divided into 4 paddocks of 0.72 ha, where each picket consisted of a farm and was divided into six plots of 0.12 ha, where the animals remained under rotational grazing. The period of adaptation to the pickets was seven days. At the beginning of the experiment the animals were weighed, identified with plastic earrings and necklaces colored according to the treatment, and treated against. The lambs were loose in the paddock at 8 am and collected at 16 hours, which returned to collective pens. During the time of grazing animals had free access to mineral supplement with monensin Ovinofós ® and water. Before entering the paddocks of pasture were sampled to characterize the chemical composition. Every seven days occurred at weighing, with fasting, to monitor the weight development. Cultivars Marandu, Aruana, Piatã and Massai were grazed for 133, 129, 143 and 142 days, respectively, until the lambs reach slaughter weight. Arriving at 32 kg lambs were evaluated subjectively for body condition score by, passed through fasting period, diet and water for 16 hours were slaughtered. Measurements were made in the inner and outer casings in addition to subjective evaluations regarding muscling, finish and quantity of pelvic-renal fat, then each was divided longitudinally into two half-carcases and cuts were made in the commercial left half, and after heavy calculated their income. Between the 12th and 13th thoracic vertebrae, was performed a cut to expose the cross section of the Longissimus dorsi, which was drawn on the rib eye area (REA) in transparent film. Fat thickness and extent of AOL GR were determined using a caliper. A tissue composition was determined by dissection of the legs. Analyzes were performed physical (color, cooking loss and shear force) and chemical composition of meat (moisture, ash, protein and lipids) in Longissimus dorsi muscle. Grazing tropical grass Brachiaria brizantha cvs. Marandu and Piatã and Panicum maximum cvs. Aruana and Massai can be used for lambs SRPD in the rainy season, because not alter the physico-chemical and chemical composition of meat
Resumo:
De que forma a evolução da estrutura institucional do Mercosul, desde sua criação até sua atual conformação, facilita a transformação de conflitos econômico-comerciais, de menor e maior grau, em conflitos políticos. Acredita-se que uma parte significativa dos conflitos no Mercosul poderia ser solucionada tecnicamente, sem resvalar nas relações políticas globais dos Estados membros, como tem ocorrido regularmente.
Resumo:
Dans cet article, on cherche la viabilité analytique du Jeu à Deux Niveaux - JDN pour examiner la situation brésilienne dans l'Organisation Mondiale du Commerce - OMC. on cherche à voir, en même temps, si le perfectionnement des institutions démocratiques brésiliennes en ce qui concerne le processus de formulation de la politique extérieure sera capable d'améliorer la réponse aux demandes des groupes d'intérêt et d'élargir la compétence technique de la diplomatie brésilienne dans les négociations commerciales internationales. on cherche aussi à savoir si ce perfectionnement peut faire monter la crédibilité et la légitimité internationale des démarches brésiliennes au sein de l'OMC, dans le sens de tourner en leur faveur les régimes internationaux. Pour cela, on analyse le contentieux des brevets pharmaceutiques mené contre les États-Unis au sein de l'OMC.
Resumo:
Objetivou-se com este estudo rastrear a inclusão de farinha de carne e ossos bovinos em dietas para poedeiras comerciais, por meio da análise dos ovos e de suas frações (gema e albúmen), pela técnica dos isótopos estáveis do carbono e nitrogênio e avaliar o índice analítico mínimo detectável. Foram utilizadas 240 galinhas poedeiras da linhagem Shaver White de 73 semanas de idade, distribuídas em delineamento inteiramente casualizado, com cinco tratamentos e seis repetições. Foram avaliados cinco níveis de inclusão (0; 1,5; 3,0; 4,5 e 6,0%) de farinha de carne e ossos bovinos em uma dieta à base de milho e farelo de soja. No 35º dia, foram tomados aleatoriamente 24 ovos por tratamento: 12 serviram para amostragem de gema e albúmen e os outros 12 para amostragem do ovo (gema + albúmen). Os resultados isotópicos foram submetidos à análise multivariada de variância e, a partir das matrizes de erro, com 95% de confiança, foram determinadas elipses para identificar as diferenças entre os resultados obtidos com o fornecimento das dietas experimentais e a dieta controle, sem farinha de carne e ossos bovinos. No ovo e na gema, a partir do par isotópico da dieta com 3,0% de farinha de carne e ossos, houve diferenciação do par do tratamento controle, enquanto, no albúmen, a diferenciação ocorreu a partir do nível de 1,5% de farinha de carne e ossos bovinos na dieta. Pela técnica dos isótopos estáveis, é possível rastrear o uso de farinha de carne e ossos bovinos na alimentação de poedeiras; no albúmen, o nível mínimo de inclusão detectável é de 1,5% e, no ovo e na gema, 3,0%.
Resumo:
O trabalho foi realizado objetivando-se avaliar o efeito da densidade populacional e da linhagem sobre as características de desempenho, o rendimento de carcaça e a qualidade da carne de peito (perda de peso por cozimento, força de cizalhamento e pH) em frangos de corte. Foram utilizados 2.925 pintos de um dia, sexados, distribuídos em um delineamento experimental inteiramente casualizado, em fatorial 3x3x2, sendo três linhagens (Ross 308, Cobb 500 e Hybro PG), três densidades (10, 13 e 16 aves/m²) e dois sexos, com duas repetições com número variável de aves em função da densidade. A densidade afetou o ganho de peso nas fases inicial e final e no período total, sendo que a densidade de 10 aves/m² apresentou o melhor ganho de peso, porém, as densidades de 13 e 16 aves/m² não diferiram entre si. O aumento da densidade promoveu maior produção de peso vivo/m² de galpão, além de incrementar a renda bruta. No entanto, não afetou o rendimento de carcaça e das partes, bem como as características de qualidade da carne. As linhagens diferiram para ganho de peso em todas as fases e para o consumo de ração na fase final e no período total de criação, porém não diferiram para o rendimento de carcaça, apesar de diferirem para o rendimento de peito, pernas, asas, dorso e gordura abdominal, sendo que para o rendimento de pernas houve diferenças apenas entre os machos e para gordura abdominal apenas entre as fêmeas. As linhagens diferiram para perda de peso da carne de peito por cozimento, mas não para maciez e pH. O sexo das aves influenciou as características de desempenho e rendimento de carcaça, mas não a qualidade da carne do peito.