Improved damage detectability in a wind turbine blade by optimal selection of vibration signal correlation coefficients

Piotr Omenzetter and Simon Hoell’s work within the Lloyd’s Register Foundation Centre for Safety and Reliability Engineering at the University of Aberdeen is supported by Lloyd’s Register Foundation. The Foundation helps to protect life and property by supporting engineering-related education, public engagement and the application of research.

Assessment of the application of automatic vehicle identification technology to traffic management : Appendix C, Evaluation of potential applications of automatic vehicle monitoring to traffic management /

Mode of access: Internet.

A bayesian artificial neural network method to characterise laminar defects using dynamic measurements

This paper reports on the development of an artificial neural network (ANN) method to detect laminar defects following the pattern matching approach utilizing dynamic measurement. Although structural health monitoring (SHM) using ANN has attracted much attention in the last decade, the problem of how to select the optimal class of ANN models has not been investigated in great depth. It turns out that the lack of a rigorous ANN design methodology is one of the main reasons for the delay in the successful application of the promising technique in SHM. In this paper, a Bayesian method is applied in the selection of the optimal class of ANN models for a given set of input/target training data. The ANN design method is demonstrated for the case of the detection and characterisation of laminar defects in carbon fibre-reinforced beams using flexural vibration data for beams with and without non-symmetric delamination damage.

Acoustic emission detection using optical fibre sensors for aerospace applications

Structural Health Monitoring (SHM) ensures the structural health and safety of critical structures covering a wide range of application areas. This thesis presents novel, low-cost and good-performance fibre Bragg grating (FBG) based systems for detection of Acoustic Emission (AE) in aircraft structures, which is a part of SHM. Importantly a key aim, during the design of these systems, was to produce systems that were sufficiently small to install in an aircraft for lifetime monitoring. Two important techniques for monitoring high frequency AE that were developed as a part of this research were, Quadrature recombination technique and Active tracking technique. Active tracking technique was used extensively and was further developed to overcome the limitations that were observed while testing it at several test facilities and with different optical fibre sensors. This system was able to eliminate any low frequency spectrum shift due to environmental perturbation and keeps the sensor always working at optimum operation point. This is highly desirable in harsh industrial and operationally active environments. Experimental work carried out in the laboratory has proved that such systems can be used for high frequency detection and have capability to detect up to 600 kHz. However, the range of frequency depends upon the requirement and design of the interrogation system as the system can be altered accordingly for different applications. Several optical fibre configurations for wavelength detection were designed during the course of this work along with industrial partners. Fibre Bragg grating Fabry-Perot (FBG-FP) sensors have shown higher sensitivity and usability than the uniform FBGs to be used with such system. This was shown experimentally. The author is certain that further research will lead to development of a commercially marketable product and the use of active tracking systems can be extended in areas of healthcare, civil infrastructure monitoring etc. where it can be deployed. Finally, the AE detection system has been developed to aerospace requirements and was tested at NDT & Testing Technology test facility based at Airbus, Filton, UK on A350 testing panels.

A simple remote sensing based information system for monitoring sites of conservation importance

Monitoring is essential for conservation of sites, but capacity to undertake it in the field is often limited. Data collected by remote sensing has been identified as a partial solution to this problem, and is becoming a feasible option, since increasing quantities of satellite data in particular are becoming available to conservationists. When suitably classified, satellite imagery can be used to delineate land cover types such as forest, and to identify any changes over time. However, the conservation community lacks (a) a simple tool appropriate to the needs for monitoring change in all types of land cover (e.g. not just forest), and (b) an easily accessible information system which allows for simple land cover change analysis and data sharing to reduce duplication of effort. To meet these needs, we developed a web-based information system which allows users to assess land cover dynamics in and around protected areas (or other sites of conservation importance) from multi-temporal medium resolution satellite imagery. The system is based around an open access toolbox that pre-processes and classifies Landsat-type imagery, and then allows users to interactively verify the classification. These data are then open for others to utilize through the online information system. We first explain imagery processing and data accessibility features, and then demonstrate the toolbox and the value of user verification using a case study on Nakuru National Park, Kenya. Monitoring and detection of disturbances can support implementation of effective protection, assist the work of park managers and conservation scientists, and thus contribute to conservation planning, priority assessment and potentially to meeting monitoring needs for Aichi target 11.

Studio di un sistema di comunicazione ad alimentazione risonante wireless.

L'elaborato tratta della progettazione di un sistema di alimentazione wireless risonante per i nodi sensori, strumenti fondamentali per il controllo delle strutture(Structural Health Monitoring). Esso si concentra sulla realizzazione di un convertitore flyback risonante (con circuito di snubber incluso per il main switch) in grado di fornire una tensione di 5 Volt in uscita a fronte di una corrente media massima sul carico di 800mA data una tensione di 12 volt in ingresso. Dopo aver introdotto il concetto di Wireless Power Transfer (WPT) e i principi fisici su cui esso poggia (induzione elettromagnetica e risonanza elettromagnetica), si presentano i modelli circuitali più utilizzati in questo ambito. Una volta illustrate le conoscenze allo stato dell'arte dell'accoppiamento induttivo risonante, si analizza il comportamento del modello scelto, al fine di evidenziare i vantaggi dell'utilizzo del circuito alla frequenza di risonanza. Sono state effettuate simulazioni con il simulatore LTspice come controprova. Si passa quindi a dimensionare i vari elementi del circuito a fronte delle specifiche stabilite. Grazie ai risultati ottenuti, si procede alla stesura del Bill Of Materials. La tesi si conclude presentando i possibili campi di ricerca e sviluppo del sistema di alimentazione.

Bridge live loading assessment and load carrying capacity estimation using health monitoring system and dynamic testing

Peer reviewed

Tracing the behaviour of a bridge using time series modelling

Peer reviewed

A seasonal ARIMAX time series model for strain-temperature relationship in an instrumented bridge

Peer reviewed

Improved damage detectability in a wind turbine blade by optimal selection of vibration signal correlation coefficients

Piotr Omenzetter and Simon Hoell’s work within the Lloyd’s Register Foundation Centre for Safety and Reliability Engineering at the University of Aberdeen is supported by Lloyd’s Register Foundation. The Foundation helps to protect life and property by supporting engineering-related education, public engagement and the application of research.