Total knee arthroplasty - a clinical and numerical study of the micromovements of the tibial implant

Introduction The importance of the micromovements in the mechanism of aseptic loosening is clinically difficult to evaluate. To complete the analysis of a series of total knee arthroplasties (TKA), we used a tridimensional numerical model to study the micromovements of the tibial implant.Material and Methods Fifty one patients (with 57 cemented Porous Coated Anatomic TKAs) were reviewed (mean follow-up 4.5 year). Radiolucency at the tibial bone-cement interface was sought on the AP radiographs and divided in 7 areas. The distribution of the radiolucency was then correlated with the axis of the lower limb as measured on the orthoradiograms.The tridimensional numerical model is based on the finite element method. It allowed the measurement of the cemented prosthetic tibial implant's displacements and the microvements generated at bone-ciment interface. A total load (2000 Newton) was applied at first vertically and asymetrically on the tibial plateau, thereby simulating an axial deviation of the lower limbs. The vector's posterior inclination then permitted the addition of a tangential component to the axial load. This type of effort is generated by complex biomechanical phenomena such as knee flexion.Results 81 per cent of the 57 knees had a radiolucent line of at least 1 mm, at one or more of the tibial cement-epiphysis jonctional areas. The distribution of these lucent lines showed that they came out more frequently at the periphery of the implant. The lucent lines appeared most often under the unloaded margin of the tibial plateau, when axial deviation of lower limbs was present.Numerical simulations showed that asymetrical loading on the tibial plateau induced a subsidence of the loaded margin (0-100 microns) and lifting off at the opposite border (0-70 microns). The postero-anterior tangential component induced an anterior displacement of the tibial implant (160-220 microns), and horizontal micromovements with non homogenous distribution at the bone-ciment interface (28-54 microns).Discussion Comparison of clinical and numerical results showed a relation between the development of radiolucent lines and the unloading of the tibial implant's margin. The deleterious effect of lower limbs' axial deviation is thereby proven. The irregular distribution of lucent lines under the tibial plateau was similar of the micromovements' repartition at the bone-cement interface when tangential forces were present. A causative relation between the two phenomenaes could not however be established.Numerical simulation is a truly useful method of study; it permits to calculate micromovements which are relative, non homogenous and of very low amplitude. However, comparative clinical studies remain as essential to ensure the credibility of results.

Comparing and validating hypothesis test procedures: Graphical and numerical tools

When the behaviour of a specific hypothesis test statistic is studied by aMonte Carlo experiment, the usual way to describe its quality is by givingthe empirical level of the test. As an alternative to this procedure, we usethe empirical distribution of the obtained \emph{p-}values and exploit itsinformation both graphically and numerically.

Selection methods regulate evolution of cooperation in digital evolution.

A key, yet often neglected, component of digital evolution and evolutionary models is the 'selection method' which assigns fitness (number of offspring) to individuals based on their performance scores (efficiency in performing tasks). Here, we study with formal analysis and numerical experiments the evolution of cooperation under the five most common selection methods (proportionate, rank, truncation-proportionate, truncation-uniform and tournament). We consider related individuals engaging in a Prisoner's Dilemma game where individuals can either cooperate or defect. A cooperator pays a cost, whereas its partner receives a benefit, which affect their performance scores. These performance scores are translated into fitness by one of the five selection methods. We show that cooperation is positively associated with the relatedness between individuals under all selection methods. By contrast, the change in the performance benefit of cooperation affects the populations' average level of cooperation only under the proportionate methods. We also demonstrate that the truncation and tournament methods may introduce negative frequency-dependence and lead to the evolution of polymorphic populations. Using the example of the evolution of cooperation, we show that the choice of selection method, though it is often marginalized, can considerably affect the evolutionary dynamics.

From Empirical Bayes to Full Bayes: Methods for Analysing Traffice Safety Data, October 25, 2004

Traffic safety engineers are among the early adopters of Bayesian statistical tools for analyzing crash data. As in many other areas of application, empirical Bayes methods were their first choice, perhaps because they represent an intuitively appealing, yet relatively easy to implement alternative to purely classical approaches. With the enormous progress in numerical methods made in recent years and with the availability of free, easy to use software that permits implementing a fully Bayesian approach, however, there is now ample justification to progress towards fully Bayesian analyses of crash data. The fully Bayesian approach, in particular as implemented via multi-level hierarchical models, has many advantages over the empirical Bayes approach. In a full Bayesian analysis, prior information and all available data are seamlessly integrated into posterior distributions on which practitioners can base their inferences. All uncertainties are thus accounted for in the analyses and there is no need to pre-process data to obtain Safety Performance Functions and other such prior estimates of the effect of covariates on the outcome of interest. In this slight, fully Bayesian methods may well be less costly to implement and may result in safety estimates with more realistic standard errors. In this manuscript, we present the full Bayesian approach to analyzing traffic safety data and focus on highlighting the differences between the empirical Bayes and the full Bayes approaches. We use an illustrative example to discuss a step-by-step Bayesian analysis of the data and to show some of the types of inferences that are possible within the full Bayesian framework.

From Empirical Bayes to Full Bayes: Methods for Analyzubg Traffic Safey Data, October 25, 2004

Traffic safety engineers are among the early adopters of Bayesian statistical tools for analyzing crash data. As in many other areas of application, empirical Bayes methods were their first choice, perhaps because they represent an intuitively appealing, yet relatively easy to implement alternative to purely classical approaches. With the enormous progress in numerical methods made in recent years and with the availability of free, easy to use software that permits implementing a fully Bayesian approach, however, there is now ample justification to progress towards fully Bayesian analyses of crash data. The fully Bayesian approach, in particular as implemented via multi-level hierarchical models, has many advantages over the empirical Bayes approach. In a full Bayesian analysis, prior information and all available data are seamlessly integrated into posterior distributions on which practitioners can base their inferences. All uncertainties are thus accounted for in the analyses and there is no need to pre-process data to obtain Safety Performance Functions and other such prior estimates of the effect of covariates on the outcome of interest. In this light, fully Bayesian methods may well be less costly to implement and may result in safety estimates with more realistic standard errors. In this manuscript, we present the full Bayesian approach to analyzing traffic safety data and focus on highlighting the differences between the empirical Bayes and the full Bayes approaches. We use an illustrative example to discuss a step-by-step Bayesian analysis of the data and to show some of the types of inferences that are possible within the full Bayesian framework.

Prothèses totales de genoux. Analyse clinique et numérique des micromouvements de l'implant tibial [Total knee prosthesis. Clinical and numerical study of micromovements of the tibial implant].

INTRODUCTION: The importance of the micromovements in the mechanism of aseptic loosening is clinically difficult to evaluate. To complete the analysis of a series of total knee arthroplasties (TKA), we used a tridimensional numerical model to study the micromovements of the tibial implant. MATERIAL AND METHODS: Fifty one patients (with 57 cemented Porous Coated Anatomic TKAs) were reviewed (mean follow-up 4.5 year). Radiolucency at the tibial bone-cement interface was sought on the AP radiographs and divided in 7 areas. The distribution of the radiolucency was then correlated with the axis of the lower limb as measured on the orthoradiograms. The tridimensional numerical model is based on the finite element method. It allowed the measurement of the cemented prosthetic tibial implant's displacements and the micromovements generated at bone-ciment interface. A total load (2000 Newton) was applied at first vertically and asymetrically on the tibial plateau, thereby simulating an axial deviation of the lower limbs. The vector's posterior inclination then permitted the addition of a tangential component to the axial load. This type of effort is generated by complex biomechanical phenomena such as knee flexion. RESULTS: 81 per cent of the 57 knees had a radiolucent line of at least 1 mm, at one or more of the tibial cement-epiphysis jonctional areas. The distribution of these lucent lines showed that they came out more frequently at the periphery of the implant. The lucent lines appeared most often under the unloaded margin of the tibial plateau, when axial deviation of lower limbs was present. Numerical simulations showed that asymetrical loading on the tibial plateau induced a subsidence of the loaded margin (0-100 microns) and lifting off at the opposite border (0-70 microns). The postero-anterior tangential component induced an anterior displacement of the tibial implant (160-220 microns), and horizontal micromovements with non homogenous distribution at the bone-ciment interface (28-54 microns). DISCUSSION: Comparison of clinical and numerical results showed a relation between the development of radiolucent lines and the unloading of the tibial implant's margin. The deleterious effect of lower limbs' axial deviation is thereby proven. The irregular distribution of lucent lines under the tibial plateau was similar of the micromovements' repartition at the bone-cement interface when tangential forces were present. A causative relation between the two phenomenaes could not however be established. Numerical simulation is a truly useful method of study; it permits to calculate micromovements which are relative, non homogenous and of very low amplitude. However, comparative clinical studies remain as essential to ensure the credibility of results.

Integrated application of geochemical and geophysical methods for hydrogeological impact assessment for tunneling in fractured rock

The interaction of tunneling with groundwater is a problem both from an environmental and an engineering point of view. In fact, tunnel drilling may cause a drawdown of piezometric levels and water inflows into tunnels that may cause problems during excavation of the tunnel. While the influence of tunneling on the regional groundwater systems may be adequately predicted in porous media using analytical solutions, such an approach is difficult to apply in fractured rocks. Numerical solutions are preferable and various conceptual approaches have been proposed to describe and model groundwater flow through fractured rock masses, ranging from equivalent continuum models to discrete fracture network simulation models. However, their application needs many preliminary investigations on the behavior of the groundwater system based on hydrochemical and structural data. To study large scale flow systems in fractured rocks of mountainous terrains, a comprehensive study was conducted in southern Switzerland, using as case studies two infrastructures actually under construction: (i) the Monte Ceneri base railway tunnel (Ticino), and the (ii) San Fedele highway tunnel (Roveredo, Graubiinden). The chosen approach in this study combines the temporal and spatial variation of geochemical and geophysical measurements. About 60 localities from both surface and underlying tunnels were temporarily and spatially monitored during more than one year. At first, the project was focused on the collection of hydrochemical and structural data. A number of springs, selected in the area surrounding the infrastructures, were monitored for discharge, electric conductivity, pH, and temperature. Water samples (springs, tunnel inflows and rains) were taken for isotopic analysis; in particular the stable isotope composition (δ2Η, δ180 values) can reflect the origin of the water, because of spatial (recharge altitude, topography, etc.) and temporal (seasonal) effects on precipitation which in turn strongly influence the isotopic composition of groundwater. Tunnel inflows in the accessible parts of the tunnels were also sampled and, if possible, monitored with time. Noble-gas concentrations and their isotope ratios were used in selected locations to better understand the origin and the circulation of the groundwater. In addition, electrical resistivity and VLF-type electromagnetic surveys were performed to identify water bearing fractures and/or weathered areas that could be intersected at depth during tunnel construction. The main goal of this work was to demonstrate that these hydrogeological data and geophysical methods, combined with structural and hydrogeological information, can be successfully used in order to develop hydrogeological conceptual models of the groundwater flow in regions to be exploited for tunnels. The main results of the project are: (i) to have successfully tested the application of electrical resistivity and VLF-electromagnetic surveys to asses water-bearing zones during tunnel drilling; (ii) to have verified the usefulness of noble gas, major ion and stable isotope compositions as proxies for the detection of faults and to understand the origin of the groundwater and its flow regimes (direct rain water infiltration or groundwater of long residence time); and (iii) to have convincingly tested the combined application of a geochemical and geophysical approach to assess and predict the vulnerability of springs to tunnel drilling. - L'interférence entre eaux souterraines et des tunnels pose des problèmes environnementaux et de génie civile. En fait, la construction d'un tunnel peut faire abaisser le niveau des nappes piézométriques et faire infiltrer de l'eau dans le tunnel et ainsi créer des problème pendant l'excavation. Alors que l'influence de la construction d'un tunnel sur la circulation régionale de l'eau souterraine dans des milieux poreux peut être prédite relativement facilement par des solution analytiques de modèles, ceci devient difficile dans des milieux fissurés. Dans ce cas-là, des solutions numériques sont préférables et plusieurs approches conceptuelles ont été proposées pour décrire et modéliser la circulation d'eau souterraine à travers les roches fissurées, en allant de modèles d'équivalence continue à des modèles de simulation de réseaux de fissures discrètes. Par contre, leur application demande des investigations importantes concernant le comportement du système d'eau souterraine basées sur des données hydrochimiques et structurales. Dans le but d'étudier des grands systèmes de circulation d'eau souterraine dans une région de montagnes, une étude complète a été fait en Suisse italienne, basée sur deux grandes infrastructures actuellement en construction: (i) Le tunnel ferroviaire de base du Monte Ceneri (Tessin) et (ii) le tunnel routière de San Fedele (Roveredo, Grisons). L'approche choisie dans cette étude est la combinaison de variations temporelles et spatiales des mesures géochimiques et géophysiques. Environs 60 localités situées à la surface ainsi que dans les tunnels soujacents ont été suiviès du point de vue temporel et spatial pendant plus de un an. Dans un premier temps le projet se focalisait sur la collecte de données hydrochimiques et structurales. Un certain nombre de sources, sélectionnées dans les environs des infrastructures étudiées ont été suivies pour le débit, la conductivité électrique, le pH et la température. De l'eau (sources, infiltration d'eau de tunnel et pluie) a été échantillonnés pour des analyses isotopiques; ce sont surtout les isotopes stables (δ2Η, δ180) qui peuvent indiquer l'origine d'une eaux, à cause de la dépendance d'effets spatiaux (altitude de recharge, topographie etc.) ainsi que temporels (saisonaux) sur les précipitations météoriques , qui de suite influencent ainsi la composition isotopique de l'eau souterraine. Les infiltrations d'eau dans les tunnels dans les parties accessibles ont également été échantillonnées et si possible suivies au cours du temps. La concentration de gaz nobles et leurs rapports isotopiques ont également été utilisées pour quelques localités pour mieux comprendre l'origine et la circulation de l'eau souterraine. En plus, des campagnes de mesures de la résistivité électrique et électromagnétique de type VLF ont été menées afin d'identifier des zone de fractures ou d'altération qui pourraient interférer avec les tunnels en profondeur pendant la construction. Le but principal de cette étude était de démontrer que ces données hydrogéologiques et géophysiques peuvent être utilisées avec succès pour développer des modèles hydrogéologiques conceptionels de tunnels. Les résultats principaux de ce travail sont : i) d'avoir testé avec succès l'application de méthodes de la tomographie électrique et des campagnes de mesures électromagnétiques de type VLF afin de trouver des zones riches en eau pendant l'excavation d'un tunnel ; ii) d'avoir prouvé l'utilité des gaz nobles, des analyses ioniques et d'isotopes stables pour déterminer l'origine de l'eau infiltrée (de la pluie par le haut ou ascendant de l'eau remontant des profondeurs) et leur flux et pour déterminer la position de failles ; et iii) d'avoir testé d'une manière convainquant l'application combinée de méthodes géochimiques et géophysiques pour juger et prédire la vulnérabilité de sources lors de la construction de tunnels. - L'interazione dei tunnel con il circuito idrico sotterraneo costituisce un problema sia dal punto di vista ambientale che ingegneristico. Lo scavo di un tunnel puô infatti causare abbassamenti dei livelli piezometrici, inoltre le venute d'acqua in galleria sono un notevole problema sia in fase costruttiva che di esercizio. Nel caso di acquiferi in materiale sciolto, l'influenza dello scavo di un tunnel sul circuito idrico sotterraneo, in genere, puô essere adeguatamente predetta attraverso l'applicazione di soluzioni analitiche; al contrario un approccio di questo tipo appare inadeguato nel caso di scavo in roccia. Per gli ammassi rocciosi fratturati sono piuttosto preferibili soluzioni numeriche e, a tal proposito, sono stati proposti diversi approcci concettuali; nella fattispecie l'ammasso roccioso puô essere modellato come un mezzo discreto ο continuo équivalente. Tuttavia, una corretta applicazione di qualsiasi modello numerico richiede necessariamente indagini preliminari sul comportamento del sistema idrico sotterraneo basate su dati idrogeochimici e geologico strutturali. Per approfondire il tema dell'idrogeologia in ammassi rocciosi fratturati tipici di ambienti montani, è stato condotto uno studio multidisciplinare nel sud della Svizzera sfruttando come casi studio due infrastrutture attualmente in costruzione: (i) il tunnel di base del Monte Ceneri (canton Ticino) e (ii) il tunnel autostradale di San Fedele (Roveredo, canton Grigioni). L'approccio di studio scelto ha cercato di integrare misure idrogeochimiche sulla qualité e quantité delle acque e indagini geofisiche. Nella fattispecie sono state campionate le acque in circa 60 punti spazialmente distribuiti sia in superficie che in sotterraneo; laddove possibile il monitoraggio si è temporalmente prolungato per più di un anno. In una prima fase, il progetto di ricerca si è concentrato sull'acquisizione dati. Diverse sorgenti, selezionate nelle aree di possibile influenza attorno allé infrastrutture esaminate, sono state monitorate per quel che concerne i parametri fisico-chimici: portata, conduttività elettrica, pH e temperatura. Campioni d'acqua sono stati prelevati mensilmente su sorgenti, venute d'acqua e precipitazioni, per analisi isotopiche; nella fattispecie, la composizione in isotopi stabili (δ2Η, δ180) tende a riflettere l'origine delle acque, in quanto, variazioni sia spaziali (altitudine di ricarica, topografia, etc.) che temporali (variazioni stagionali) della composizione isotopica delle precipitazioni influenzano anche le acque sotterranee. Laddove possibile, sono state campionate le venute d'acqua in galleria sia puntualmente che al variare del tempo. Le concentrazioni dei gas nobili disciolti nell'acqua e i loro rapporti isotopici sono stati altresi utilizzati in alcuni casi specifici per meglio spiegare l'origine delle acque e le tipologie di circuiti idrici sotterranei. Inoltre, diverse indagini geofisiche di resistività elettrica ed elettromagnetiche a bassissima frequenza (VLF) sono state condotte al fine di individuare le acque sotterranee circolanti attraverso fratture dell'ammasso roccioso. Principale obiettivo di questo lavoro è stato dimostrare come misure idrogeochimiche ed indagini geofisiche possano essere integrate alio scopo di sviluppare opportuni modelli idrogeologici concettuali utili per lo scavo di opere sotterranee. I principali risultati ottenuti al termine di questa ricerca sono stati: (i) aver testato con successo indagini geofisiche (ERT e VLF-EM) per l'individuazione di acque sotterranee circolanti attraverso fratture dell'ammasso roccioso e che possano essere causa di venute d'acqua in galleria durante lo scavo di tunnel; (ii) aver provato l'utilità di analisi su gas nobili, ioni maggiori e isotopi stabili per l'individuazione di faglie e per comprendere l'origine delle acque sotterranee (acque di recente infiltrazione ο provenienti da circolazioni profonde); (iii) aver testato in maniera convincente l'integrazione delle indagini geofisiche e di misure geochimiche per la valutazione della vulnérabilité delle sorgenti durante lo scavo di nuovi tunnel. - "La NLFA (Nouvelle Ligne Ferroviaire à travers les Alpes) axe du Saint-Gothard est le plus important projet de construction de Suisse. En bâtissant la nouvelle ligne du Saint-Gothard, la Suisse réalise un des plus grands projets de protection de l'environnement d'Europe". Cette phrase, qu'on lit comme présentation du projet Alptransit est particulièrement éloquente pour expliquer l'utilité des nouvelles lignes ferroviaires transeuropéens pour le développement durable. Toutefois, comme toutes grandes infrastructures, la construction de nouveaux tunnels ont des impacts inévitables sur l'environnement. En particulier, le possible drainage des eaux souterraines réalisées par le tunnel peut provoquer un abaissement du niveau des nappes piézométriques. De plus, l'écoulement de l'eau à l'intérieur du tunnel, conduit souvent à des problèmes d'ingénierie. Par exemple, d'importantes infiltrations d'eau dans le tunnel peuvent compliquer les phases d'excavation, provoquant un retard dans l'avancement et dans le pire des cas, peuvent mettre en danger la sécurité des travailleurs. Enfin, l'infiltration d'eau peut être un gros problème pendant le fonctionnement du tunnel. Du point de vue de la science, avoir accès à des infrastructures souterraines représente une occasion unique d'obtenir des informations géologiques en profondeur et pour échantillonner des eaux autrement inaccessibles. Dans ce travail, nous avons utilisé une approche pluridisciplinaire qui intègre des mesures d'étude hydrogéochimiques effectués sur les eaux de surface et des investigations géophysiques indirects, tels que la tomographic de résistivité électrique (TRE) et les mesures électromagnétiques de type VLF. L'étude complète a été fait en Suisse italienne, basée sur deux grandes infrastructures actuellement en construction, qui sont le tunnel ferroviaire de base du Monte Ceneri, une partie du susmentionné projet Alptransit, situé entièrement dans le canton Tessin, et le tunnel routière de San Fedele, situé a Roveredo dans le canton des Grisons. Le principal objectif était de montrer comment il était possible d'intégrer les deux approches, géophysiques et géochimiques, afin de répondre à la question de ce que pourraient être les effets possibles dû au drainage causés par les travaux souterrains. L'accès aux galeries ci-dessus a permis une validation adéquate des enquêtes menées confirmant, dans chaque cas, les hypothèses proposées. A cette fin, nous avons fait environ 50 profils géophysiques (28 imageries électrique bidimensionnels et 23 électromagnétiques) dans les zones de possible influence par le tunnel, dans le but d'identifier les fractures et les discontinuités dans lesquelles l'eau souterraine peut circuler. De plus, des eaux ont été échantillonnés dans 60 localités situées la surface ainsi que dans les tunnels subjacents, le suivi mensuelle a duré plus d'un an. Nous avons mesurés tous les principaux paramètres physiques et chimiques: débit, conductivité électrique, pH et température. De plus, des échantillons d'eaux ont été prélevés pour l'analyse mensuelle des isotopes stables de l'hydrogène et de l'oxygène (δ2Η, δ180). Avec ces analyses, ainsi que par la mesure des concentrations des gaz rares dissous dans les eaux et de leurs rapports isotopiques que nous avons effectués dans certains cas spécifiques, il était possible d'expliquer l'origine des différents eaux souterraines, les divers modes de recharge des nappes souterraines, la présence de possible phénomènes de mélange et, en général, de mieux expliquer les circulations d'eaux dans le sous-sol. Le travail, même en constituant qu'une réponse partielle à une question très complexe, a permis d'atteindre certains importants objectifs. D'abord, nous avons testé avec succès l'applicabilité des méthodes géophysiques indirectes (TRE et électromagnétiques de type VLF) pour prédire la présence d'eaux souterraines dans le sous-sol des massifs rocheux. De plus, nous avons démontré l'utilité de l'analyse des gaz rares, des isotopes stables et de l'analyses des ions majeurs pour la détection de failles et pour comprendre l'origine des eaux souterraines (eau de pluie par le haut ou eau remontant des profondeurs). En conclusion, avec cette recherche, on a montré que l'intégration des ces informations (géophysiques et géochimiques) permet le développement de modèles conceptuels appropriés, qui permettant d'expliquer comment l'eau souterraine circule. Ces modèles permettent de prévoir les infiltrations d'eau dans les tunnels et de prédire la vulnérabilité de sources et des autres ressources en eau lors de construction de tunnels.

Optimization of Snow Drifting Mitigation and Control Methods for Iowa Conditions Part II, TR-626, 2015

Blowing and drifting of snow is a major concern for transportation efficiency and road safety in regions where their development is common. One common way to mitigate snow drift on roadways is to install plastic snow fences. Correct design of snow fences is critical for road safety and maintaining the roads open during winter in the US Midwest and other states affected by large snow events during the winter season and to maintain costs related to accumulation of snow on the roads and repair of roads to minimum levels. Of critical importance for road safety is the protection against snow drifting in regions with narrow rights of way, where standard fences cannot be deployed at the recommended distance from the road. Designing snow fences requires sound engineering judgment and a thorough evaluation of the potential for snow blowing and drifting at the construction site. The evaluation includes site-specific design parameters typically obtained with semi-empirical relations characterizing the local transport conditions. Among the critical parameters involved in fence design and assessment of their post-construction efficiency is the quantification of the snow accumulation at fence sites. The present study proposes a joint experimental and numerical approach to monitor snow deposits around snow fences, quantitatively estimate snow deposits in the field, asses the efficiency and improve the design of snow fences. Snow deposit profiles were mapped using GPS based real-time kinematic surveys (RTK) conducted at the monitored field site during and after snow storms. The monitored site allowed testing different snow fence designs under close to identical conditions over four winter seasons. The study also discusses the detailed monitoring system and analysis of weather forecast and meteorological conditions at the monitored sites. A main goal of the present study was to assess the performance of lightweight plastic snow fences with a lower porosity than the typical 50% porosity used in standard designs of such fences. The field data collected during the first winter was used to identify the best design for snow fences with a porosity of 50%. Flow fields obtained from numerical simulations showed that the fence design that worked the best during the first winter induced the formation of an elongated area of small velocity magnitude close to the ground. This information was used to identify other candidates for optimum design of fences with a lower porosity. Two of the designs with a fence porosity of 30% that were found to perform well based on results of numerical simulations were tested in the field during the second winter along with the best performing design for fences with a porosity of 50%. Field data showed that the length of the snow deposit away from the fence was reduced by about 30% for the two proposed lower-porosity (30%) fence designs compared to the best design identified for fences with a porosity of 50%. Moreover, one of the lower-porosity designs tested in the field showed no significant snow deposition within the bottom gap region beneath the fence. Thus, a major outcome of this study is to recommend using plastic snow fences with a porosity of 30%. It is expected that this lower-porosity design will continue to work well for even more severe snow events or for successive snow events occurring during the same winter. The approach advocated in the present study allowed making general recommendations for optimizing the design of lower-porosity plastic snow fences. This approach can be extended to improve the design of other types of snow fences. Some preliminary work for living snow fences is also discussed. Another major contribution of this study is to propose, develop protocols and test a novel technique based on close range photogrammetry (CRP) to quantify the snow deposits trapped snow fences. As image data can be acquired continuously, the time evolution of the volume of snow retained by a snow fence during a storm or during a whole winter season can, in principle, be obtained. Moreover, CRP is a non-intrusive method that eliminates the need to perform man-made measurements during the storms, which are difficult and sometimes dangerous to perform. Presently, there is lots of empiricism in the design of snow fences due to lack of data on fence storage capacity on how snow deposits change with the fence design and snow storm characteristics and in the estimation of the main parameters used by the state DOTs to design snow fences at a given site. The availability of such information from CRP measurements should provide critical data for the evaluation of the performance of a certain snow fence design that is tested by the IDOT. As part of the present study, the novel CRP method is tested at several sites. The present study also discusses some attempts and preliminary work to determine the snow relocation coefficient which is one of the main variables that has to be estimated by IDOT engineers when using the standard snow fence design software (Snow Drift Profiler, Tabler, 2006). Our analysis showed that standard empirical formulas did not produce reasonable values when applied at the Iowa test sites monitored as part of the present study and that simple methods to estimate this variable are not reliable. The present study makes recommendations for the development of a new methodology based on Large Scale Particle Image Velocimetry that can directly measure the snow drift fluxes and the amount of snow relocated by the fence.

Numerical procedure for estimating temperature in solarized soils

The objective of this work was to develop a simplified numerical procedure for the estimation of accumulated monthly hours of solarized soil temperatures. The proposed model requires monthly means of daily solar radiation and maximum air temperature as input data, and a daily pattern of temperature variation assumed to be sine-shaped. The procedure was verified using observations made during the years 1992 and 1993 in Jaguariúna, SP. The proposed procedure can predict monthly temperature hours at 10 cm depth in the solarized soil, with acceptable accuracy, in the region for which it was developed.

Direct numerical simulations of interface dynamics to link capillary pressure and total surface energy

The flow of two immiscible fluids through a porous medium depends on the complex interplay between gravity, capillarity, and viscous forces. The interaction between these forces and the geometry of the medium gives rise to a variety of complex flow regimes that are difficult to describe using continuum models. Although a number of pore-scale models have been employed, a careful investigation of the macroscopic effects of pore-scale processes requires methods based on conservation principles in order to reduce the number of modeling assumptions. In this work we perform direct numerical simulations of drainage by solving Navier-Stokes equations in the pore space and employing the Volume Of Fluid (VOF) method to track the evolution of the fluid-fluid interface. After demonstrating that the method is able to deal with large viscosity contrasts and model the transition from stable flow to viscous fingering, we focus on the macroscopic capillary pressure and we compare different definitions of this quantity under quasi-static and dynamic conditions. We show that the difference between the intrinsic phase-average pressures, which is commonly used as definition of Darcy-scale capillary pressure, is subject to several limitations and it is not accurate in presence of viscous effects or trapping. In contrast, a definition based on the variation of the total surface energy provides an accurate estimate of the macroscopic capillary pressure. This definition, which links the capillary pressure to its physical origin, allows a better separation of viscous effects and does not depend on the presence of trapped fluid clusters.

Improved Methods for Determining Wind Loads on Highway Sign and Traffic-Signal Structures, TR-559, 2007

The main objective of the proposed study is to use Computational Fluid Dynamics (CFD) tools to determine the wind loads by accurate numerical simulations of air flow characteristics around large highway sign structures under severe wind speeds conditions. Fully three-dimensional Reynolds- Averaged Navier-Stokes (RANS) simulations are used to estimate the total force on different panels, as well as the actual pressure distribution on the front and back faces of the panels. In particular, the present study investigates the effects of aspect ratio and sign spacing for regular panels, the effect of sign depth for the dynamic message signs that are now being used on Iowa highways, the effect induced by the presence of back-to-back signs, the effect of the presence of add-on exit signs, and the effect of the presence of trucks underneath the signs potentially creating “wind tunnel” effect.

Monte Carlo Methods in Parameter Estimation of Nonlinear Models

Yksi keskeisimmistä tehtävistä matemaattisten mallien tilastollisessa analyysissä on mallien tuntemattomien parametrien estimointi. Tässä diplomityössä ollaan kiinnostuneita tuntemattomien parametrien jakaumista ja niiden muodostamiseen sopivista numeerisista menetelmistä, etenkin tapauksissa, joissa malli on epälineaarinen parametrien suhteen. Erilaisten numeeristen menetelmien osalta pääpaino on Markovin ketju Monte Carlo -menetelmissä (MCMC). Nämä laskentaintensiiviset menetelmät ovat viime aikoina kasvattaneet suosiotaan lähinnä kasvaneen laskentatehon vuoksi. Sekä Markovin ketjujen että Monte Carlo -simuloinnin teoriaa on esitelty työssä siinä määrin, että menetelmien toimivuus saadaan perusteltua. Viime aikoina kehitetyistä menetelmistä tarkastellaan etenkin adaptiivisia MCMC menetelmiä. Työn lähestymistapa on käytännönläheinen ja erilaisia MCMC -menetelmien toteutukseen liittyviä asioita korostetaan. Työn empiirisessä osuudessa tarkastellaan viiden esimerkkimallin tuntemattomien parametrien jakaumaa käyttäen hyväksi teoriaosassa esitettyjä menetelmiä. Mallit kuvaavat kemiallisia reaktioita ja kuvataan tavallisina differentiaaliyhtälöryhminä. Mallit on kerätty kemisteiltä Lappeenrannan teknillisestä yliopistosta ja Åbo Akademista, Turusta.

Theoretical and numerical study of thermomagnetic convection in magnetic fluids

In this thesis, the magnetic field control of convection instabilities and heat and mass transfer processesin magnetic fluids have been investigated by numerical simulations and theoretical considerations. Simulation models based on finite element and finite volume methods have been developed. In addition to standard conservation equations, themagnetic field inside the simulation domain is calculated from Maxwell equations and the necessary terms to take into account for the magnetic body force and magnetic dissipation have been added to the equations governing the fluid motion.Numerical simulations of magnetic fluid convection near the threshold supportedexperimental observations qualitatively. Near the onset of convection the competitive action of thermal and concentration density gradients leads to mostly spatiotemporally chaotic convection with oscillatory and travelling wave regimes, previously observed in binary mixtures and nematic liquid crystals. In many applications of magnetic fluids, the heat and mass transfer processes including the effects of external magnetic fields are of great importance. In addition to magnetic fluids, the concepts and the simulation models used in this study may be applied also to the studies of convective instabilities in ordinary fluids as well as in other binary mixtures and complex fluids.

Level Set Methods in Image Processing

This thesis gives an overview of the use of the level set methods in the field of image science. The similar fast marching method is discussed for comparison, also the narrow band and the particle level set methods are introduced. The level set method is a numerical scheme for representing, deforming and recovering structures in an arbitrary dimensions. It approximates and tracks the moving interfaces, dynamic curves and surfaces. The level set method does not define how and why some boundary is advancing the way it is but simply represents and tracks the boundary. The principal idea of the level set method is to represent the N dimensional boundary in the N+l dimensions. This gives the generality to represent even the complex boundaries. The level set methods can be powerful tools to represent dynamic boundaries, but they can require lot of computing power. Specially the basic level set method have considerable computational burden. This burden can be alleviated with more sophisticated versions of the level set algorithm like the narrow band level set method or with the programmable hardware implementation. Also the parallel approach can be used in suitable applications. It is concluded that these methods can be used in a quite broad range of image applications, like computer vision and graphics, scientific visualization and also to solve problems in computational physics. Level set methods and methods derived and inspired by it will be in the front line of image processing also in the future.