Studies on the Quality of Rainwater at Various Land Use Locations and Variations by Interaction with Domestic Rainwater Harvesting Systems

The present study focused on the quality of rainwater at various land use locations and its variations on interaction with various domestic rainwater harvesting systems.Sampling sites were selected based upon the land use pattern of the locations and were classified as rural, urban, industrial and sub urban. Rainwater samples were collected from the south west monsoon of May 2007 to north east monsoon of October 2008, from four sampling sites namely Kothamangalam, Emakulam, Eloor and Kalamassery, in Ernakulam district of the State of Kerala, which characterized typical rural, urban, industrial and suburban locations respectively. Rain water samples at various stages of harvesting were also collected. The samples were analyzed according to standard procedures and their physico-chemical and microbiological parameters were determined. The variations of the chemical composition of the rainwater collected were studied using statistical methods. It was observed that 17.5%, 30%, 45.8% and 12.1% of rainwater samples collected at rural, urban, industrial and suburban locations respectively had pH less than 5.6, which is considered as the pH of cloud water at equilibrium with atmospheric CO,.Nearly 46% of the rainwater samples were in acidic range in the industrial location while it was only 17% in the rural location. Multivariate statistical analysls was done using Principal Component Analysis, and the sources that inf1uence the composition of rainwater at each locations were identified .which clearly indicated that the quality of rain water is site specific and represents the atmospheric characteristics of the free fall The quality of harvested rainwater showed significant variations at different stages of harvesting due to deposition of dust from the roof catchment surface, leaching of cement constituents etc. Except the micro biological quality, the harvested rainwater satisfied the Indian Standard guide lines for drinking water. Studies conducted on the leaching of cement constituents in water concluded that tanks made with ordinary portland cement and portland pozzolana cement could be safely used for storage of rain water.

Lightweight monitoring of label switched paths for bandwidth management

The purpose of resource management is the efficient and effective use of network resources, for instance bandwidth. In this article, a connection oriented network scenario is considered, where a certain amount of bandwidth is reserved for each label switch path (LSP), which is a logical path, in a MPLS or GMPLS environment. Assuming there is also some kind of admission control (explicit or implicit), these environments typically provide quality of service (QoS) guarantees. It could happen that some LSPs become busy, thus rejecting connections, while other LSPs may be under-utilised. We propose a distributed lightweight monitoring technique, based on threshold values, the objective of which is to detect congestion when it occurs in an LSP and activate the corresponding alarm which will trigger a dynamic bandwidth reallocation mechanism

A lightweight technique for assessing risks in requirements analysis

A simple and practical technique for assessing the risks, that is, the potential for error, and consequent loss, in software system development, acquired during a requirements engineering phase is described. The technique uses a goal-based requirements analysis as a framework to identify and rate a set of key issues in order to arrive at estimates of the feasibility and adequacy of the requirements. The technique is illustrated and how it has been applied to a real systems development project is shown. How problems in this project could have been identified earlier is shown, thereby avoiding costly additional work and unhappy users.

Nitrogen budgets for three cropping systems fertilised with cattle manure

A field plot experiment was set up on a sandy loam soil of SW England in order to determine the efficiency of nitrogen use from different cattle manures. The manure treatments were low and high dry matter cattle slurries and one farmyard manure applied at a target rate of 200 kg total Nha(-1) year(-1), and an untreated control. There were three different cropping systems: ryegrass/clover mixture, maize/rye and maize/bare soil, which were evaluated during 1998/99 and 1999/00. Measurements were made of N losses, N uptake and herbage DM yields. Result showed that manure type had a significant effect on N utilisation only for maize. N balances were negative in maize (approximately -247 to -10 kg N) compared to grass (approximately 5-158 kg N). Agronomic management was more important than manure type in influencing N losses, where soil cultivation appeared to be a key factor when comparing maize and grass systems. (C) 2004 Elsevier Ltd. All rights reserved.

A lightweight technique for assessing risks in requirements analysis

A simple and practical technique for assessing the risks, that is, the potential for error, and consequent loss, in software system development, acquired during a requirements engineering phase is described. The technique uses a goal-based requirements analysis as a framework to identify and rate a set of key issues in order to arrive at estimates of the feasibility and adequacy of the requirements. The technique is illustrated and how it has been applied to a real systems development project is shown. How problems in this project could have been identified earlier is shown, thereby avoiding costly additional work and unhappy users.

Styx grid services: lightweight middleware for efficient scientific workflows

The service-oriented approach to performing distributed scientific research is potentially very powerful but is not yet widely used in many scientific fields. This is partly due to the technical difficulties involved in creating services and workflows and the inefficiency of many workflow systems with regard to handling large datasets. We present the Styx Grid Service, a simple system that wraps command-line programs and allows them to be run over the Internet exactly as if they were local programs. Styx Grid Services are very easy to create and use and can be composed into powerful workflows with simple shell scripts or more sophisticated graphical tools. An important feature of the system is that data can be streamed directly from service to service, significantly increasing the efficiency of workflows that use large data volumes. The status and progress of Styx Grid Services can be monitored asynchronously using a mechanism that places very few demands on firewalls. We show how Styx Grid Services can interoperate with with Web Services and WS-Resources using suitable adapters.

Hardware development of the Yorick series of active vision systems

This paper presents a review of the design and development of the Yorick series of active stereo camera platforms and their integration into real-time closed loop active vision systems, whose applications span surveillance, navigation of autonomously guided vehicles (AGVs), and inspection tasks for teleoperation, including immersive visual telepresence. The mechatronic approach adopted for the design of the first system, including head/eye platform, local controller, vision engine, gaze controller and system integration, proved to be very successful. The design team comprised researchers with experience in parallel computing, robot control, mechanical design and machine vision. The success of the project has generated sufficient interest to sanction a number of revisions of the original head design, including the design of a lightweight compact head for use on a robot arm, and the further development of a robot head to look specifically at increasing visual resolution for visual telepresence. The controller and vision processing engines have also been upgraded, to include the control of robot heads on mobile platforms and control of vergence through tracking of an operator's eye movement. This paper details the hardware development of the different active vision/telepresence systems.

Influence of Post and Resin Cement on Stress Distribution of Maxillary Central Incisors Restored with Direct Resin Composite

The current study evaluated the influence of two endodontic post systems and the elastic modulus and film thickness of resin cement on stress distribution in a maxillary central incisor (MCI) restored with direct resin composite using finite element analysis (FEA). A three-dimensional model of an MCI with a coronary fracture and supporting structures was performed. A static chewing pressure of 2.16 N/mm(2) was applied to two areas on the palatal surface of the composite restoration. Zirconia ceramic (ZC) and glass fiber (GF) posts were considered. The stress distribution was analyzed in the post, dentin and cement layer when ZC and GF posts were fixed to the root canals using resin cements of different elastic moduli (7.0 and 18.6 GPa) and different layer thicknesses (70 and 200 mu m). The different post materials presented a significant influence on stress distribution with lesser stress concentration when using the GF post. The higher elastic modulus cement created higher stress levels within itself. The cement thicknesses did not present significant changes.

Bond Strength of Fiber Posts in Different Root Thirds Using Resin Cement

Purpose: The aim of the study was to assess the in vitro bond strength (BS) of glass fiber posts (GF) and carbon fiber posts (CF) in the cervical, middle, and apical thirds of root canals cemented with RelyX-Unicem (RX) and Cement-Post (CP). Materials and Methods: Forty maxillary canines were divided into 4 groups (n = 10) according to the cement and post used: group 1: GF and RX; group 2: CF and RX; group 3: GF and CP; group 4: CF and CP. The push-out test was applied in the cervical, middle and apical thirds of each specimen to assess bond strength of the cement/post complex to the root canal wall. The data obtained were submitted to ANOVA (Bonferroni test, p < 0.05), and fracture analysis was done with SEM. Results: The GF posts presented the best results when cemented with RX and with CF (p < 0.05). RX presented the highest BS values for both GF and CF (p < 0.05). For all the groups, BS was higher in the cervical third, followed by the middle and apical thirds. Fracture analysis showed a predominance of cohesive fracture of posts for RX, and a predominance of adhesive fracture between dentin/cement, and mixed failure mode for CP. Conclusion: GF posts cemented with RX presented the highest BS values in all root thirds.

Environmental Assessment of Rammed Earth Construction Systems

Present concerns for sustainable development have led to a revival of traditional building practices using natural or recycled resources. There is a perception that buildings constructed from such materials are environmentally benign. This perception is questionable, as often no evaluation is undertaken to assess the associated environmental impacts. Rammed earth is one such construction technology that has seen renewed interest in recent years. The energy required to manufacture materials (i.e. embodied energy) is a significant component of the life cycle energy associated with buildings. This paper assesses the embodied energy of rammed earth construction relative to brick veneer and cavity brick construction. Rammed earth was found to have significantly less embodied energy than cavity brick construction (to which it is closer in thermal performance), but was approximately equivalent to brick veneer construction. Topics of further research identified include thermal performance and strategies for reducing the embodied energy of cement used for earth stabilisation.

A lightweight intrusion alert fusion system

In this paper, we present some practical experience on implementing an alert fusion mechanism from our project. After investigation on most of the existing alert fusion systems, we found the current body of work alternatively weighed down in the mire of insecure design or rarely deployed because of their complexity. As confirmed by our experimental analysis, unsuitable mechanisms could easily be submerged by an abundance of useless alerts. Even with the use of methods that achieve a high fusion rate and low false positives, attack is also possible. To find the solution, we carried out analysis on a series of alerts generated by well-known datasets as well as realistic alerts from the Australian Honey-Pot. One important finding is that one alert has more than an 85% chance of being fused in the following 5 alerts. Of particular importance is our design of a novel lightweight Cache-based Alert Fusion Scheme, called CAFS. CAFS has the capacity to not only reduce the quantity of useless alerts generated by IDS (Intrusion Detection System), but also enhance the accuracy of alerts, therefore greatly reducing the cost of fusion processing. We also present reasonable and practical specifications for the target-oriented fusion policy that provides a quality guarantee on alert fusion, and as a result seamlessly satisfies the process of successive correlation. Our experimental results showed that the CAFS easily attained the desired level of survivable, inescapable alert fusion design. Furthermore, as a lightweight scheme, CAFS can easily be deployed and excel in a large amount of alert fusions, which go towards improving the usability of system resources. To the best of our knowledge, our work is a novel exploration in addressing these problems from a survivable, inescapable and deployable point of view.

CAFS : a novel lightweight cache-based scheme for large-scale intrusion alert fusion

In this paper, we present some practical experiences on implementing an alert fusion mechanism from our project. After investigation on most of the existing alert fusion systems, we found the current body of work alternatively weighed down in the mire of insecure design or rarely deployed because of their complexity. As confirmed by our experimental analysis, unsuitable mechanisms could easily be submerged by an abundance of useless alerts. Even with the use of methods that achieve a high fusion rate and low false positives, attack is also possible. To find the solution, we carried out analysis on a series of alerts generated by well-known datasets as well as realistic alerts from the Australian Honey-Pot. One important finding is that one alert has more than an 85% chance of being fused in the following five alerts. Of particular importance is our design of a novel lightweight Cache-based Alert Fusion Scheme, called CAFS. CAFS has the capacity to not only reduce the quantity of useless alerts generated by intrusion detection system, but also enhance the accuracy of alerts, therefore greatly reducing the cost of fusion processing. We also present reasonable and practical specifications for the target-oriented fusion policy that provides a quality guarantee on alert fusion, and as a result seamlessly satisfies the process of successive correlation. Our experiments compared CAFS with traditional centralized fusion. The results showed that the CAFS easily attained the desired level of simple, counter-escapable alert fusion design. Furthermore, as a lightweight scheme, CAFS can easily be deployed and excel in a large amount of alert fusions, which go towards improving the usability of system resources. To the best of our knowledge, our work is a practical exploration in addressing problems from the academic point of view. Copyright © 2011 John Wiley & Sons, Ltd.

A serverless ultra-lightweight secure search protocol for EPC Class-1 Gen-2 UHF RFID tags

Radio Frequency Identification (RFID) is a technology that enables the non-contact, automatic and unique identification of objects using radio waves. Its use for commercial applications has recently become attractive with RFID technology seen as the replacement for the optical barcode system that is currently in widespread use. RFID has many advantages over the traditional barcode and these advantages have the potential to significantly increase the efficiency of decentralised business environments such as logistics and supply chain management. One of the important features of an RFID system is its ability to search for a particular tag among a group of tags. In order to ensure the privacy and security of the tags, the search has to be conducted in a secure fashion. To our knowledge not much work has been done in this secure search area of RFID. The limited work that has been done does not comply with the EPC Class-1 Gen-2 standards since most of them use expensive hash operations or sophisticated encryption schemes that cannot be implemented on low-cost passive tags that are highly resource constrained. Our work aims to fill this gap by proposing a serverless ultra-lightweight secure search protocol that does not use the expensive hash functions or any complex encryption schemes but achieves compliance with EPC Class-1 Gen-2 standards while meeting the required security requirements. Our protocol is based on XOR encryption and random numbers - operations that are easily implemented on low-cost RFID tags. Our protocol also provides additional protection using a blind-factor to prevent tracking attacks. Since our protocol is EPC Class-1 Gen-2 compliant it makes it possible to implement it on low-cost passive RFID tags.

Designing architectural morphing skins with elastic modular systems

This paper discusses the issues of designing architectural skins that can be physically morphed to adapt to changing needs. To achieve this architectural vision, designers have focused on developing mechanical joints, components, and systems for actuation and kinetic transformation. However, the unexplored approach of using lightweight elastic form-changing materials provides an opportunity for designing responsive architectural skins and skeletons with fewer mechanical operations. This research aims to develop elastic modular systems that can be applied as a second skin or brise-soleil to existing buildings.The use of the second skin has the potential to allow existing buildings to perform better in various climatic conditions and to provide a visually compelling skin. This approach is evaluated through three design experiments with prototypes, namely Tent, Curtain and Blind, to serve two fundamental purposes: Comfort and Communication. These experimental prototypes explore the use of digital and physical computation embedded in form-changing materials to design architectural morphing skins that manipulate sunlight and act as responsive shading devices.