Export of organic matter, sulphate and base cations from boreal headwater catchments downstream to the coast: impacts of land use and climate

The terrestrial export of dissolved organic matter (DOM) is associated with climate, vegetation and land use, and thus is under the influence of climatic variability and human interference with terrestrial ecosystems, their soils and hydrological cycles. The present study provides an assessment of spatial variation of DOM concentrations and export, and interactions between DOM, catchment characteristics, land use and climatic factors in boreal catchments. The influence of catchment characteristics, land use and climatic drivers on the concentrations and export of total organic carbon (TOC), total organic nitrogen (TON) and dissolved organic phosphorus (DOP) was estimated using stream water quality, forest inventory and climatic data from 42 Finnish pristine forested headwater catchments, and water quality monitoring, GIS land use, forest inventory and climatic data from the 36 main Finnish rivers (and their sub-catchments) flowing to the Baltic Sea. Moreover, the export of DOM in relation to land use along a European climatic gradient was studied using river water quality and land use data from four European areas. Additionally, the role of organic and minerogenic acidity in controlling pH levels in Finnish rivers and pristine streams was studied by measuring organic anion, sulphate (SO4) and base cation (Ca, Mg, K and Na) concentrations. In all study catchments, TOC was a major fraction of DOM, with much lower proportions of TON and DOP. Moreover, most of TOC and TON was in a dissolved form. The correlation between TOC and TON concentrations was strong and TOC concentrations explained 78% of the variation in TON concentrations in pristine headwater streams. In a subgroup of 20 headwater catchments with similar climatic conditions and low N deposition in eastern Finland, the proportion of peatlands in the catchment and the proportion of Norway spruce (Picea abies Karsten) of the tree stand had the strongest correlation with the TOC and TON concentrations and export. In Finnish river basins, TOC export increased with the increasing proportion of peatland in the catchment, whereas TON export increased with increasing extent of agricultural land. The highest DOP concentrations and export were recorded in river basins with a high extent of agricultural land and urban areas, reflecting the influence of human impact on DOP loads. However, the most important predictor for TOC, TON and DOP export in Finnish rivers was the proportion of upstream lakes in the catchment. The higher the upstream lake percentage, the lower the export indicating organic matter retention in lakes. Molar TOC:TON ratio decreased from headwater catchments covered by forests and peatlands to the large river basins with mixed land use, emphasising the effect of the land use gradient on the stoichiometry of rivers. This study also demonstrated that the land use of the catchments is related to both organic and minerogenic acidity in rivers and pristine headwater streams. Organic anion dominated in rivers and streams situated in northern Finland, reflecting the higher extent of peatlands in these areas, whereas SO4 dominated in southern Finland and on western coastal areas, where the extent of fertile areas, agricultural land, urban areas, acid sulphate soils, and sulphate deposition is highest. High TOC concentrations decreased pH values in the stream and river water, whereas no correlation between SO4 concentrations and pH was observed. This underlines the importance of organic acids in controlling pH levels in Finnish pristine headwater streams and main rivers. High SO4 concentrations were associated with high base cation concentrations and fertile areas, which buffered the effects of SO4 on pH.

Thermodynamics of electroweak matter

The electroweak theory is the part of the standard model of particle physics that describes the weak and electromagnetic interactions between elementary particles. Since its formulation almost 40 years ago, it has been experimentally verified to a high accuracy and today it has a status as one of the cornerstones of particle physics. Thermodynamics of electroweak physics has been studied ever since the theory was written down and the features the theory exhibits at extreme conditions remain an interesting research topic even today. In this thesis, we consider some aspects of electroweak thermodynamics. Specifically, we compute the pressure of the standard model to high precision and study the structure of the electroweak phase diagram when finite chemical potentials for all the conserved particle numbers in the theory are introduced. In the first part of the thesis, the theory, methods and essential results from the computations are introduced. The original research publications are reprinted at the end.

Interfacial microrheology as a tool to study viscoelastic transitions in nanoconfined soft matter

We present a method to perform in situ microrheological measurements on monolayers of soft materials undergoing viscoelastic transitions under compression. Using the combination of a Langmuir trough mounted on the inverted microscope stage of a laser scanning confocal microscope we track the motion of individual fluorescent quantum dots partly dispersed in monolayers spread at the air-water interface. From the calculated mean square displacement of the probe particles and extending a well established scheme of the generalized Stokes-Einstein relation in bulk to the interface we arrive at the viscoelastic modulus for the respective monolayers as a function of surface density. Measurements on monolayers of glassy as well as nonglassy polymers and a standard fatty acid clearly show sensitivity of our technique to subtle variations, in the viscoelastic properties of the highly confined materials under compression. Evidence for possible spatial variations of such viscoelastic properties at a given surface density for the fatty acid monolayer is also provided.

Interfacial microrheology as a tool to study viscoelastic transitions in nanoconfined soft matter

We present a method to perform in situ microrheological measurements on monolayers of soft materials undergoing viscoelastic transitions under compression. Using the combination of a Langmuir trough mounted on the inverted microscope stage of a laser scanning confocal microscope we track the motion of individual fluorescent quantum dots partly dispersed in monolayers spread at the air-water interface. From the calculated mean square displacement of the probe particles and extending a well established scheme of the generalized Stokes-Einstein relation in bulk to the interface we arrive at the viscoelastic modulus for the respective monolayers as a function of surface density. Measurements on monolayers of glassy as well as nonglassy polymers and a standard fatty acid clearly show sensitivity of our technique to subtle variations, in the viscoelastic properties of the highly confined materials under compression. Evidence for possible spatial variations of such viscoelastic properties at a given surface density for the fatty acid monolayer is also provided.

Intermolecular interactions in pi -conjugated systems: Application to polyenes

A computational scheme has been developed for strongly interacting systems wherein the intermolecular interaction is introduced as a charge-induced-dipole term. Within this approximation, the model Hamiltonian is exactly solved using a valence-bond basis. The validity of the scheme has been checked by use of exact calculations on small model systems. The method has been applied to finite polyenes to study the shifts in the ground-state energies and dipole-allowed excited-state energies in the presence of neighbors. Our calculations show a red shift in the optical gap of the infinite polyene by 0.124 eV, which is rather small compared to the experimental red shift. This is traced to the larger inaccuracy in the calculated shift in the excited state. The calculated shift in the ground-state energies are more accurate and hence the method is better suited for studying the effect of intermolecular interactions on the properties of the ground state.

CFD Based Design Optimizations of the Diffuser of a Gas Dynamically Driver Laser Cavity

Based on the an earlier CFD analysis of the performance of the gas-dynamically controlled laser cavity [1]it was found that there is possibility of optimizing the geometry of the diffuser that can bring about reductions in both size and cost of the system by examining the critical dimensional requirements of the diffuser. Consequently,an extensive CFD analysis has been carried out for a range of diffuser configurations by simulating the supersonic flow through the arrangement including the laser cavity driven by a bank of converging – diverging nozzles and the diffuser. The numerical investigations with 3D-RANS code are carried out to capture the flow patterns through diffusers past the cavity that has multiple supersonic jet interactions with shocks leading to complex flow pattern. Varying length of the diffuser plates is made to be the basic parameter of the study. The analysis reveals that the pressure recovery pattern during the flow through the diffuser from the simulation, being critical for the performance of the laser device shows its dependence on the diffuser length is weaker beyond a critical lower limit and this evaluation of this limit would provide a design guideline for a more efficient system configuration.The observation based on the parametric study shows that the pressure recovery transients in the near vicinity of the cavity is not affected for the reduction in the length of the diffuser plates up to its 10% of the initial size, indicating the design in the first configuration that was tested experimentally has a large factor of margin. The flow stability in the laser cavity is found to be unaffected since a strong and stable shock is located at the leading edge of the diffuser plates while the downstream shock and flow patterns are changed, as one would expect. Results of the study for the different lengths of diffusers in the range of 10% to its full length are presented, keeping the experimentally tested configuration used in the earlier study [1] as the reference length. The conclusions drawn from the analysis is found to be of significance since it provides new design considerations based on the understanding of the intricacies of the flow, allowing for a hardware optimization that can lead to substantial size reduction of the device with no loss of performance.

Computational Analysis of Flow through a Multiple Nozzle Driven Laser Cavity and Diffuser

Computations have been carried out for simulating supersonic flow through a set of converging-diverging nozzles with their expanding jets forming a laser cavity and flow patterns through diffusers, past the cavity. A thorough numerical investigation with 3-D RANS code is carried out to capture the flow distribution which comprises of shock patterns and multiple supersonic jet interactions. The analysis of pressure recovery characteristics during the flow through the diffusers is an important parameter of the simulation and is critical for the performance of the laser device. The results of the computation have shown a close agreement with the experimentally measured parameters as well as other established results indicating that the flow analysis done is found to be satisfactory.

Exact entanglement studies of strongly correlated systems: role of long-range interactions and symmetries of the system

We study the bipartite entanglement of strongly correlated systems using exact diagonalization techniques. In particular, we examine how the entanglement changes in the presence of long-range interactions by studying the Pariser-Parr-Pople model with long-range interactions. We compare the results for this model with those obtained for the Hubbard and Heisenberg models with short-range interactions. This study helps us to understand why the density matrix renormalization group (DMRG) technique is so successful even in the presence of long-range interactions. To better understand the behavior of long-range interactions and why the DMRG works well with it, we study the entanglement spectrum of the ground state and a few excited states of finite chains. We also investigate if the symmetry properties of a state vector have any significance in relation to its entanglement. Finally, we make an interesting observation on the entanglement profiles of different states (across the energy spectrum) in comparison with the corresponding profile of the density of states. We use isotropic chains and a molecule with non-Abelian symmetry for these numerical investigations.

Guided Wave based Damage Detection in a Composite T-joint using 3D Scanning Laser Doppler Vibrometer

Composite T-joints are commonly used in modern composite airframe, pressure vessels and piping structures, mainly to increase the bending strength of the joint and prevents buckling of plates and shells, and in multi-cell thin-walled structures. Here we report a detailed study on the propagation of guided ultrasonic wave modes in a composite T-joint and their interactions with delamination in the co-cured co-bonded flange. A well designed guiding path is employed wherein the waves undergo a two step mode conversion process, one is due to the web and joint filler on the back face of the flange and the other is due to the delamination edges close to underneath the accessible surface of the flange. A 3D Laser Doppler Vibrometer is used to obtain the three components of surface displacements/velocities of the accessible face of the flange of the T-joint. The waves are launched by a piezo ceramic wafer bonded on to the back surface of the flange. What is novel in the proposed method is that the location of any change in material/geometric properties can be traced by computing a frequency domain power flow along a scan line. The scan line can be chosen over a grid either during scan or during post-processing of the scan data off-line. The proposed technique eliminates the necessity of baseline data and disassembly of structure for structural interrogation.

Supersymmetric Chern-Simons theories with vector matter

In this paper we discuss SU(N) Chern-Simons theories at level k with both fermionic and bosonic vector matter. In particular we present an exact calculation of the free energy of the N = 2 supersymmetric model (with one chiral field) for all values of the `t Hooft coupling in the large N limit. This is done by using a generalization of the standard Hubbard-Stratanovich method because the SUSY model contains higher order polynomial interactions.

Effect of Net-Fluence on waveguide formation in ultrafast laser inscribed chalcogenide glass

Waveguides were fabricated on GeGaSEr chalcogenide glass using ultrafast laser inscription method. The thermal diffusion model is discussed for understanding the light matter interaction and shown the effect of net-fluence in waveguide formation on chalcogenide glass. (C) 2012 Optical Society of America

Guided-wave-based damage detection in a composite T-joint using 3D scanning laser Doppler vibrometer

Composite T-joints are commonly used in modern composite airframe, pressure vessels and piping structures, mainly to increase the bending strength of the joint and prevents buckling of plates and shells, and in multi-cell thin-walled structures. Here we report a detailed study on the propagation of guided ultrasonic wave modes in a composite T-joint and their interactions with delamination in the co-cured co-bonded flange. A well designed guiding path is employed wherein the waves undergo a two step mode conversion process, one is due to the web and joint filler on the back face of the flange and the other is due to the delamination edges close to underneath the accessible surface of the flange. A 3D Laser Doppler Vibrometer is used to obtain the three components of surface displacements/velocities of the accessible face of the flange of the T-joint. The waves are launched by a piezo ceramic wafer bonded on to the back surface of the flange. What is novel in the proposed method is that the location of any change in material/geometric properties can be traced by computing a frequency domain power flow along a scan line. The scan line can be chosen over a grid either during scan or during post-processing of the scan data off-line. The proposed technique eliminates the necessity of baseline data and disassembly of structure for structural interrogation.

Open loop Model for WDM Links

Wavelength Division Multiplexing (WDM) techniques overfibrelinks helps to exploit the high bandwidth capacity of single mode fibres. A typical WDM link consisting of laser source, multiplexer/demultiplexer, amplifier and detectoris considered for obtaining the open loop gain model of the link. The methodology used here is to obtain individual component models using mathematical and different curve fitting techniques. These individual models are then combined to obtain the WDM link model. The objective is to deduce a single variable model for the WDM link in terms of input current to system. Thus it provides a black box solution for a link. The Root Mean Square Error (RMSE) associated with each of the approximated models is given for comparison. This will help the designer to select the suitable WDM link model during a complex link design.

A simplified model for dark matter interacting primarily with gluons

We consider a simple renormalizable model providing a UV completion for dark matter whose interactions with the Standard Model are primarily via the gluons. The model consists of scalar dark matter interacting with scalar colored mediator particles. A novel feature is the fact that (in contrast to more typical models containing dark matter whose interactions are mediated via colored scalars) the colored scalars typically decay into multi-quark final states, with no associated missing energy. We construct this class of models and examine associated phenomena related to dark matter annihilation, scattering with nuclei, and production at colliders.

Effect of dark matter halo on global spiral modes in galaxies

Low surface brightness (LSB) galaxies form a major class of galaxies, and are characterized by low disc surface density and low star formation rate. These are known to be dominated by dark matter halo from the innermost regions. Here, we study the role of the dark matter halo on the grand-design, m = 2, spiral modes in a galactic disc by carrying out a global mode analysis in the WKB approximation. The Bohr-Sommerfeld quantization rule is used to determine how many discrete global spiral modes are permitted. First, a typical superthin, LSB galaxy UGC 7321 is studied by taking only the galactic disc, modelled as a fluid; and then the disc embedded in a dark matter halo. We find that both cases permit the existence of global spiral modes. This is in contrast to earlier results where the inclusion of dark matter halo was shown to nearly fully suppress local, swing-amplified spiral features. Although technically global modes are permitted in the fluid model as shown here, we argue that due to lack of tidal interactions, these are not triggered in LSB galaxies. For comparison, we carried out a similar analysis for the Galaxy, for which the dark matter halo does not dominate in the inner regions. We show that here too the dark matter halo has little effect, hence the disc embedded in a halo is also able to support global modes. The derived pattern speed of the global mode agrees fairly well with the observed value for the Galaxy.