Estudo de falhas por fadiga em caldeiras

In recent years, increasing demand for energy has led to studies to increase the amount of electricity produced. Due to this fact, more and more boilers are becoming important sources of electricity generation. To raise the efficiency of energy generated in the boilers is necessary to raise the steam pressure and temperature to values previously unimaginable. The use of more resistant materials and maintenance practices and most appropriate operation made it possible. The objective of this study is to test the main types of failure in a chemical recovery boiler, in particular due to fatigue in the superheater, because it is a component subjected to high temperatures and thus more subject to different failures. In this manner this study aims to reduce the incidence of unscheduled maintenance shutdowns, increasing the operation time under appropriate conditions. Modeling performed in this study, the failure did not occur, because we considered only the mechanical stress. Under normal conditions, mechanical stress in combination with thermal stresses can cause cracks in the tubes due to cyclical stresses, leading to fatigue failure

Análise de fadiga em rodas automotivas utilizando método dos elementos finitos

The increasing search for better performance at the automotive industry, especially on the matter of fuel consumption, caused a progressive evolution of industrial technology. For the wheel this study is based on the try of reducing mass and decreasing the moment of inertia, characteristics that directly reflect on the performance parameter, as consumption and acceleration, so that it also is effective on the growth of the profit margin, since it reduces the costs of the locomotion. In this paper will be applied the Finite Element Analysis to explain the wheel behavior and identify ways to improve the performance. To the analyze it will be simulated a test condition established by ABNT NBR 6751:2009 foreseeing a possible collapse through general yielding and fatigue. The load here presented results from the equation presented on the norms and in the datas provided by the manufacturer

Fadiga axial do aço inoxidável 15-5 PH tratado pela implantação iônica por imersão em plasma

When materials for application in aircraft structural components are studied, it must be considered that they will be submitted to cyclic loading, and this is an important parameter to design the study in fatigue life of the materials. Whereas, for example, a landing gear operation, the study of fatigue life and corrosion in the materials used in it is essential, especially when you want to use new techniques for surface treatments. The objective is to study the influence of surface treatment of immersion ion implantation nitrogen plasma, in axial fatigue of Stainless steel 15-5 PH in 39-42 HRC condition. Stainless steel 15-5 PH was tested in axial fatigue and corrosion in salt spray. It was also performed microindentation tests, optical microscopy for microstructural analysis and scanning electron microscopy for fractographic analysis. It was observed that the 3IP had no effect on the thickness of the material and not the hardness of it, and still provided a significant increase in fatigue life of the material

Estudo do efeito do processo de shot peening na taxa de propagação de trinca por fadiga na liga aeronáutica 2024 - T3

Pós-graduação em Engenharia Mecânica - FEG

Fadiga em compósitos 5HS carbono/epóxi processados via RTM: relação entre cargas axiais no plano e modos de delaminação

Pós-graduação em Engenharia Mecânica - FEG

Influência de três tratamentos de superfície para cerâmicas a base de zircônia na resistência adesiva e no comportamento à fadiga do material

Pós-graduação em Odontologia Restauradora - ICT

Estudo da fadiga em liga de alumínio aeronáutico 7475-T761

This work will address the study of fatigue conditions with constant load in an alloy of aluminum analysis 7475 - T761, so we can better understand the conditions of the aircrafts which contain this alloy in their structures. A literature review, which was discussed the concepts of fracture mechanics, fatigue, aeronautical components, chemical analysis of aluminum alloys, fatigue problems that appears in the aircrafts, metallographic analysis, and testing of optical microscopy tensile, fatigue and microhardness, surface analysis (MEV) study of the chemical composition of the alloy in question, the main causes of crashes, was performed, completing the work, analysis of data from tensile test, hardness and fatigue together with the interpretation of images of optical microscopy and scanning electron was taken. The data indicated the high mechanical strength of the alloy, along with its microstructure indicating elongated grains and high surface contour, which shows such resistance by hindering the movement of dislocations. The grooves are clearly shown in the MEV images as well as the classic with increased fatigue loading and subsequent reduction of the number of cycles to rupture behavior shown in the graphs. Therefore we observed the optimal behavior is supported by the league when subjected to fatigue loadings

Estudo do comportamento em fadiga das ligas AA6005, AA6063 e AA6351

Aluminum alloys have shown great potential for the automotive industry, especially aluminum alloys 6xxx series. This category has good mechanical strength and excellent corrosion resistance, important for the areas of construction and transport. The automotive industry has always shown great interest in the study of fatigue behavior, because structural components are subjected to cyclic and vibration loads, generating cracks and fracturing. The mechanical response depends on the material properties, applications, surface condition and microstructure. In this work was study the fatigue behavior of high cycle of machined bodies (not polished) and the effect of roughness on the fatigue life for three aluminum alloys of 6xxx series: AA6005, AA6351 and AA606, all in the T6 condition . S / N curves were made from fatigue tests in rotating bending (R = -1). The influence of roughness was studied by measuring the roughness of each specimen. Was compare the fatigue behavior of polished specimen and not polished specimens. The fractured surfaces of samples were observed by MEV, and it was observed that most of nucleation sites for fatigue crack is initiated below the surface

O paradigmático caso do processo às juntas militares argentinas

This article analyzes the case of the proceedings against Argentina’s Military Juntas that led to jail those responsible for heinous crimes committed during the military dictatorship. The said proceeding has a high symbolic value in the struggle for human rights in Latin America and is relevant and timely in Brazil where the right to the truth regarding the missing people during the military dictatorship is in debate, as well as the invalidation of the Amnesty Act regarding the common crimes of torture, rape and / or kidnapping, among others. In the case of Argentina, following Roxin’s doctrine of mediate authorship, the Court held that the crimes were committed by the military through the use of an organized power apparatus and emphatically dismissed allegations that such crimes were justified in the so-called “dirty war”. Thus, the case against the Military Juntas has become a paradigmatic one, not only in Argentina, where many military leaders had to respond to criminal actions, but for all countries in the region that faced similar situations in recent history.

Resistência à flexão em porcelana feldspática: efeito da ciclagem mecânica e limite de fadiga pelo método escada

This study evaluated the fatigue limit (FL) by the staircase method and the effect of mechanical cycling on the flexural strength (FS) of Duceragold feldspathic porcelain. Specimens (25 x 5 x 2 mm) were made according to manufacturer’s directions and submitted to three-point flexural strength test (n = 10). To determine FL (n = 30; 10,000 cycles; 2 Hz), an initial loading of 60% of the FS and an incremental loading (step) of 3% of the FS were used. Data were analyzed by Anova and Tukey´s test (p < 0.05). Although the proposed cycles have not reduced FS significantly, fractography analysis showed striation, characteristic signs of mechanical fatigue.

Influência do tratamento superficial 3IP na vida em fadiga dos aços ABNT 4340 e 15-5PH para aplicação aeronáutica

Pós-graduação em Engenharia Mecânica - FEG

Análise estrutural e fadiga em prótese implanto-suportada unitária através do método dos elementos finitos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Confiabilidade de coroas com infraestrutura em zircônia sob fadiga deslizante: efeito do tipo de tratamento interno para cimentação

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efeito de métodos de desgaste com pontas diamantadas e da ressinterização sobre o limite de fadiga flexural de uma zircônia parcialmente estabilizada por ítria

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação dos parâmetros tempo, corrente e pressão na soldagem por resistência elétrica de compósitos PEI/fibras contínuas: influência na resistência mecânica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)