Propagation of the Ignition Front against Airflow in Packed Beds of Wood Particles

Combustion of wood is increasing because of the needs of decreasing the emissions of carbon dioxide and the amount of waste going to landfills. Wood based fuels are often scattered on a large area. The transport distances should be short enough to prevent too high costs, and so the size of heating and power plants using wood fuels is often rather small. Combustion technologies of small-size units have to be developed to reach efficient and environmentally friendly energy production. Furnaces that use different packed bed combustion or gasification techniques areoften most economic in small-scale energy production. Ignition front propagation rate affects the stability, heat release rate and emissions of packed bed combustion. Ignition front propagation against airflow in packed beds of wood fuels has been studied. The research has been carried out mainly experimentally. Theoretical aspects have been considered to draw conclusions about the experimental results. The effects of airflow rate, moisture content of the fuel, size, shape and density of particles, and porosity of the bed on the propagation rate of the ignition front have been studied. The experiments were carried out in a pot furnace. The fuels used in the experiments were mainly real wood fuels that are often burned in the production of energy. The fuel types were thin wood chips, saw dust, shavings, wood chips, and pellets with different sizes. Also a few mixturesof the above were tested. Increase in the moisture content of the fuel decreases the propagation rates of the ignition front and makes the range of possible airflow rates narrower because of the energy needed for the evaporation of water and the dilution of volatile gases due to evaporated steam. Increase in the airflow rate increases the ignition rate until a maximum rate of propagation is reached after which it decreases. The maximum flame propagation rate is not always reached in stoichiometric combustion conditions. Increase in particle size and density transfers the optimum airflow rate towards fuel lean conditions. Mixing of small and large particles is often advantageous, because small particles make itpossible to reach the maximum ignition rate in fuel rich conditions, and large particles widen the range of possible airflow rates. A correlation was found forthe maximum rate of ignition front propagation in different wood fuels. According to the correlation, the maximum ignition mass flux is increased when the sphericity of the particles and the porosity of the bed are increased and the moisture content of the fuel is decreased. Another fit was found between sphericity and porosity. Increase in sphericity decreases the porosity of the bed. The reasons of the observed results are discussed.

Valamo a short handbook for travellers - [Front cover]

Helsinki : The Finnish Tourist Association 1926

Reconstruction of Fresnel Holograms using partial wave front information

n this work we analyze the behavior of complex information in Fresnel domain taking into account the limited capability to display complex transmittance values of current liquid crystal devices, when used as holographic displays. In order to do this analysis we compute the reconstruction of Fresnel holograms at several distances using the different parts of the complex distribution (real and imaginary parts, amplitude and phase) as well as using the full complex information adjusted with a method that combines two configurations of the devices in an adding architecture. The RMS error between the amplitude of these reconstructions and the original amplitude is used to evaluate the quality of the information displayed. The results of the error analysis show different behavior for the reconstructions using the different parts of the complex distribution and using the combined method of two devices. Better reconstructions are obtained when using two devices whose configurations densely cover the complex plane when they are added. Simulated and experimental results are also presented.

Fibroblast surface-associated FGF-2 promotes contact-dependent colorectal cancer cell migration and invasion through FGFR-SRC signaling and integrin αvβ5-mediated adhesion.

Carcinoma-associated fibroblasts were reported to promote colorectal cancer (CRC) invasion by secreting motility factors and extracellular matrix processing enzymes. Less is known whether fibroblasts may induce CRC cancer cell motility by contact-dependent mechanisms. To address this question we characterized the interaction between fibroblasts and SW620 and HT29 colorectal cancer cells in 2D and 3D co-culture models in vitro. Here we show that fibroblasts induce contact-dependent cancer cell elongation, motility and invasiveness independently of deposited matrix or secreted factors. These effects depend on fibroblast cell surface-associated fibroblast growth factor (FGF) -2. Inhibition of FGF-2 or FGF receptors (FGFRs) signaling abolishes these effects. FGFRs activate SRC in cancer cells and inhibition or silencing of SRC in cancer cells, but not in fibroblasts, prevents fibroblasts-mediated effects. Using an RGD-based integrin antagonist and function-blocking antibodies we demonstrate that cancer cell adhesion to fibroblasts requires integrin αvβ5. Taken together, these results demonstrate that fibroblasts induce cell-contact-dependent colorectal cancer cell migration and invasion under 2D and 3D conditions in vitro through fibroblast cell surface-associated FGF-2, FGF receptor-mediated SRC activation and αvβ5 integrin-dependent cancer cell adhesion to fibroblasts. The FGF-2-FGFRs-SRC-αvβ5 integrin loop might be explored as candidate therapeutic target to block colorectal cancer invasion.

A Generic Framework Architecture for Portal Front End

A modem software development requires quick results and excellent quality, which leads to high demand for reusability in design and implementation of software components. The purpose of this thesis was to design and implement a reusable framework for portal front ends, including common portal features, such as authentication and authorization. The aim was also to evaluate frameworks as components of reuse and compare them to other reuse techniques. As the result of this thesis, a goo'd picture of framework's life cycle, problem domain and the actual implementation process of the framework, was obtained. It was also found out that frameworks fit well to solve recurrent and similar problems in a restricted problem domain. The outcome of this thesis was a prototype of a generic framework and an example application built on it. The implemented framework offered an abstract base for the portal front ends, using object-oriented methods and wellknown design patterns. The example application demonstrated the speed and ease of the application development based on the application frameworks.

Is the Front Line Prepared for the Changing Faces of Patients? Predictors of Cross-Cultural Preparedness Among Clinical Nurses and Resident Physicians in Lausanne, Switzerland.

UNLABELLED: Phenomenon: Assuring quality medical care for all persons requires that healthcare providers understand how sociocultural factors affect a patient's health beliefs/behaviors. Switzerland's changing demographics highlight the importance of provider cross-cultural preparedness for all patients-especially those at risk for social/health precarity. We evaluated healthcare provider cross-cultural preparedness for commonly encountered vulnerable patient profiles. APPROACH: A survey on cross-cultural care was mailed to Lausanne University hospital's "front-line healthcare providers": clinical nurses and resident physicians at our institution. Preparedness items asked "How prepared do you feel to care for ... ?" (referring to example patient profiles) on an ascending 5-point Likert scale. We examined proportions of "4 - well/5 - very well prepared" and the mean composite score for preparedness. We used linear regression to examine the adjusted effect of demographics, work context, cultural-competence training, and cross-cultural care problem awareness, on preparedness. FINDINGS: Of 885 questionnaires, 368 (41.2%) were returned: 124 (33.6%) physicians and 244 (66.4%) nurses. Mean preparedness composite was 3.30 (SD = 0.70), with the lowest proportion of healthcare providers feeling prepared for patients "whose religious beliefs affect treatment" (22%). After adjustment, working in a sensitized department (β = 0.21, p = .01), training on the history/culture of a specific group (β = 0.25, p = .03), and awareness regarding (a) a lack of practical experience caring for diverse populations (β = 0.25, p = .004) and (b) inadequate cross-cultural training (β = 0.18, p = .04) were associated with higher preparedness. Speaking French as a dominant language and physician role (vs. nurse) were negatively associated with preparedness (β = -0.26, p = .01; β = -0.22, p = .01). Insights: The state of cross-cultural care preparedness among Lausanne's front-line healthcare providers leaves room for improvement. Our study points toward institutional strategies to improve preparedness: notably, making sure departments are sensitized to cross-cultural care resources and increasing provider diversity to reflect the changing Swiss demographic.

Are patients with non-invasive papillary thyroid carcinoma, follicular variant (niFV-PTC) and minimally invasive follicular thyroid carcinoma with capsular invasion only (miFTC-CIO) overtreated?An institutional experience

Background. Recently several meetings and position papers advocate a change in terminology regarding thyroid neoplasms with indolent behavior, proposing the term "tumor" instead of "carcinoma". This change concerns non-invasive papillary thyroid carcinoma, follicular variant (niFV-PTC) and minimally invasive follicular thyroid carcinoma with capsular invasion only (miFTC-CIO). The aim of our study was to evaluate the impact of considering niFV-PTC and miFTC-CIO as lesions of low malignant potential, and to see how this change would influence patient management at our institution. Methods. A 32 months retrospective review of all well differentiated thyroid carcinomas (WDTC) (papillary and follicular carcinomas) diagnosed at our institution was performed, excluding tumors of uncertain malignant potential as well as poorly differentiated and anaplastic carcinomas. We retrieved cases of niFV-PTC and miFTC-CIO, reviewed histological slides to confirm diagnosis and recorded patient treatment. Results. A total of 9 (7.3%) niFV-PTC (4 males and 5 females, aged between 30 and 68 years, mean: 50.8 years old) and 2 (1.6%) cases of miFTC-CIO (2 females, 31 and 51 years old) were identified out of 122 WDTC diagnosed in the study period. The initial treatment consisted in 5 lobectomies and 6 total thyroidectomies (3 because of a compressive goiter, 2 because of a fine-needle aspiration diagnosis of suspicious for papillary thyroid carcinoma and 1 because of a fine-needle aspiration diagnosis of papillary carcinoma). The treatment following the histological diagnosis consisted in 4 thyroidectomy completions among patients who underwent simple lobectomy (4/5, 80%) and 9/11 (82%) radioablations with I131. Conclusions. The incidence of niFV-PTC is low at our institution, probably because we apply strict diagnostic criteria for this lesion. Simple lobectomy with negative margins is the treatment of choice in cases diagnosed as niFV-PTC and miFTC-CIO, due to the indolent course of these neoplasms. All cases with thyroidectomy completions and radioablations could have been avoided. As a consequence, the change of such terminology heavily impacts the malignancy risk evaluated cytologically as well as patients' management.

Architectural characterization of a delta-front reservoir analogue combining ground penetrating radar and electrical resistivity tomography: Roda Sandstone (Lower Eocene, Graus-Tremp basin, Spain)

Three-dimensional reconstruction of reservoir analogues can be improved combining data from different geophysical methods. Ground Penetrating Radar (GPR) and Electrical Resistivity Tomography (ERT) data are valuable tools, since they provide subsurface information from internal architecture and facies distribution of sedimentary rock bodies, enabling the upgrading of depositional models and heterogeneity reconstruction. The Lower Eocene Roda Sandstone is a well-known deltaic complex widely studied as a reservoir analogue that displays a series of sandstone wedges with a general NE to SW progradational trend. To provide a better understanding of internal heterogeneity of a 10m-thick progradational delta-front sandstone unit, 3D GPR data were acquired. In addition, common midpoints (CMP) to measure the sandstone subsoil velocity, test profiles with different frequency antennas (25, 50 and 100MHz) and topographic data for subsequent correction in the geophysical data were also obtained. Three ERT profiles were also acquired to further constrain GPR analysis. These geophysical results illustrate the geometry of reservoir analogue heterogeneities both depositional and diagenetic in nature, improving and complementing previous outcrop-derived data. GPR interpretation using radar stratigraphy principles and attributes analysis provided: 1)tridimensional geometry of major stratigraphic surfaces that define four units in the GPR Prism, 2) image the internal architecture of the units and their statistical study of azimuth and dips, useful for a quick determination of paleocurrent directions. These results were used to define the depositional architecture of the progradational sandbody that shows an arrangement in very-high-frequency sequences characterized by clockwise paleocurrent variations and decrease of the sedimentary flow, similar to those observed at a greater scale in the same system. This high-frequency sequential arrangement has been attributed to the autocyclic dynamics of a supply-dominated delta- front where fluvial and tidal currents are in competition. The resistivity models enhanced the viewing of reservoir quality associated with cement distribution caused by depositional and early diagenetic processes related to the development of transgressive and regressive systems tracts in igh-frequency sequences.

Applying Active Front End To Multilevel Inverter

The aim of this work was to make an active front end from IGBTs for a multilevel inverter. The work was done for Mosart II, a long term still ongoing Vacon Oyj project. The purpose of the AFE is to balance the DC-voltage and to put the returning power back to the grid instead of the breaking chopper and the capacitor. With a diode rectifier the bridge only allows power to pass in one direction and the switching times are not controllable. That means the rectifier always takes the highest phase and the phases are always conducting the same 120◦. With an AFE it is possible to actively change the rectifiers switching pattern. A diode bridge also generates much greater losses than an IGBT bridge. With these arguments it is rational to start researching the possibility of an AFE in a multilevel inverter.

Progress in front propagation research

We review the progress in the field of front propagation in recent years. We survey many physical, biophysical and cross-disciplinary applications, including reduced-variable models of combustion flames, Reid's paradox of rapid forest range expansions, the European colonization of North America during the 19th century, the Neolithic transition in Europe from 13 000 to 5000 years ago, the description of subsistence boundaries, the formation of cultural boundaries, the spread of genetic mutations, theory and experiments on virus infections, models of cancer tumors, etc. Recent theoretical advances are unified in a single framework, encompassing very diverse systems such as those with biased random walks, distributed delays, sequential reaction and dispersion, cohabitation models, age structure and systems with several interacting species. Directions for future progress are outlined

Tracking Invasion Histories in the Sea: Facing Complex Scenarios Using Multilocus Data

In recent years, new analytical tools have allowed researchers to extract historical information contained in molecular data, which has fundamentally transformed our understanding of processes ruling biological invasions. However, the use of these new analytical tools has been largely restricted to studies of terrestrial organisms despite the growing recognition that the sea contains ecosystems that are amongst the most heavily affected by biological invasions, and that marine invasion histories are often remarkably complex. Here, we studied the routes of invasion and colonisation histories of an invasive marine invertebrate Microcosmus squamiger (Ascidiacea) using microsatellite loci, mitochondrial DNA sequence data and 11 worldwide populations. Discriminant analysis of principal components, clustering methods and approximate Bayesian computation (ABC) methods showed that the most likely source of the introduced populations was a single admixture event that involved populations from two genetically differentiated ancestral regions - the western and eastern coasts of Australia. The ABC analyses revealed that colonisation of the introduced range of M. squamiger consisted of a series of non-independent introductions along the coastlines of Africa, North America and Europe. Furthermore, we inferred that the sequence of colonisation across continents was in line with historical taxonomic records - first the Mediterranean Sea and South Africa from an unsampled ancestral population, followed by sequential introductions in California and, more recently, the NE Atlantic Ocean. We revealed the most likely invasion history for world populations of M. squamiger, which is broadly characterized by the presence of multiple ancestral sources and non-independent introductions within the introduced range. The results presented here illustrate the complexity of marine invasion routes and identify a cause-effect relationship between human-mediated transport and the success of widespread marine non-indigenous species, which benefit from stepping-stone invasions and admixture processes involving different sources for the spread and expansion of their range.

Front Speed of Language Replacement

We use two coupled equations to analyze the space-time dynamics of two interacting languages. Firstly, we introduce a cohabitation model, which is more appropriate for human populations than classical (non-cohabitation) models. Secondly, using numerical simulations we nd the front speed of a new language spreading into a region where another language was previously used. Thirdly, for a special case we derive an analytical formula that makes it possible to check the validity of our numerical simulations. Finally, as an example, we nd that the observed front speed for the spread of the English language into Wales in the period 1961-1981 is consistent with the model predictions. We also nd that the e¤ects of linguistic parameters are much more important than those of parameters related to population dispersal and reproduction. If the initial population densities of both languages are similar, they have no e¤ect on the front speed. We outline the potential of the new model to analyze relationships between language replacement and genetic replacement

Managing the Front End of Innovation in a Networked Company Environment - Combining Strategy, Processes and Systems of Innovation

The objective of the thesis is to enhance the understanding about the management of the front end phases of the innovation process in a networked environment. The thesis approaches the front end of innovation from three perspectives, including the strategy, processes and systems of innovation. The purpose of the use of different perspectives in the thesis is that of providing an extensive systemic view of the front end, and uncovering the complex nature of innovation management. The context of the research is the networked operating environment of firms. The unit of analysis is the firm itself or its innovation processes, which means that this research approaches the innovation networks from the point of view of a firm. The strategy perspective of the thesis emphasises the importance of purposeful innovation management, the innovation strategy of firms. The role of innovation processes is critical in carrying out innovation strategies in practice, supporting the development of organizational routines for innovation, and driving the strategic renewal of companies. The primary focus of the thesis from systems perspective is on idea management systems, which are defined as a part of innovation management systems, and defined for this thesis as any working combination of methodology and tools (manual or IT-supported) that enhance the management of innovations within their early phases. The main contribution of the thesis are the managerial frameworks developed for managing the front end of innovation, which purposefully “wire” the front end of innovation into the strategy and business processes of a firm. The thesis contributes to modern innovation management by connecting the internal and external collaboration networks as foundational elements for successful management of the early phases of innovation processes in a dynamic environment. The innovation capability of a firm is largely defined by its ability to rely on and make use of internal and external collaboration already during the front end activities, which by definition include opportunity identification and analysis, idea generation, profileration and selection, and concept definition. More specifically, coordination of the interfaces between these activities, and between the internal and external innovation environments of a firm is emphasised. The role of information systems, in particular idea management systems, is to support and delineate the innovation-oriented behaviour and interaction of individuals and organizations during front end activities. The findings and frameworks developed in the thesis can be used by companies for purposeful promotion of their front end processes. The thesis provides a systemic strategy framework for managing the front end of innovation – not as a separate process, but as an elemental bundle ofactivities that is closely linked to the overall innovation process and strategy of a firm in a distributed environment. The theoretical contribution of the thesis relies on the advancement of the open innovation paradigm in the strategic context of a firm within its internal and external innovation environments. This thesis applies the constructive research approach and case study methodology to provide theoretically significant results, which are also practically beneficial.