Influence of ball-milled low purity boron powder on the superconductivity of MgB2

MgB2 samples were prepared using as-supplied commercial 96% boron with strong crystalline phase and the same 96% boron (B) after ball milling. The effects of the properties of the starting B powder on the superconductivity were evaluated. We observed that samples using ball-milled 96% B, in comparison with the one made from the as-supplied 96% B, were character- ized by small grain size, broadened full width at half maximum (FWHM), and enhanced magnetic critical current density (J(c)). J(c) reached 2 x 10(3) Acm(-2) at 5 K and 8 T. The improved pinning of these samples seems to be caused by enhanced grain boundary pinning at high field.

Existence and stability of new nanoreactors: Highly swollen hexagonal liquid crystals

We report the preparation of direct hexagonal liquid crystals, constituted of oil-swollen cylinders arranged on a triangular lattice in water. The volume ratio of oil over water, rho, can be as large as 3.8. From the lattice parameter measured by small-angle X-ray scattering, we show that all the oil is indeed incorporated into the cylinders, thus allowing the diameter of the cylinders to be controlled over one decade range, provided that the ionic strength of the aqueous medium and rho are varied concomitantly. These hexagonal swollen liquid crystals (SLCs) have been first reported with sodium dodecyl sulfate as anionic surfactant, cyclohexane as solvent, 1-pentanol as co-surfactant, and sodium chloride as salt (Ramos, L.; Fabre, P. Langmuir 1997, 13, 13). The stability of these liquid crystals is investigated when the pH of the aqueous medium or the chemical nature of the components (salt and surfactant) is changed. We demonstrate that the range of stability is quite extended, rendering swollen hexagonal phases potentially useful for the fabrication of nanomaterials. As illustrations, we finally show that gelation of inorganic particles in the continuous aqueous medium of a SLC and polymerization within the oil-swollen cylinders of a SLC can be conducted without disrupting the hexagonal order of the system.

Action of auxins and/or boron, in the process of formation of roots in cuttings of coffee (Coffea-Arabica L CV Mundo-Novo)

The objective of present research was to verify the IBA and/or NAA effects with boron, on rooting of coffee (Coffea arabica L. cv 'Mundo Novo') stem cuttings. Therefore it were used stem cuttings from semi-hardwood orthotropous branches, having two nodes, with aproximately 10 cm of lenght. The cuttings were treateds during 24 hours with IBA and/or NAA plus boron solutions. The treatments' effect was observed trough the following observation, 90 days after planting: rooting percentage and number of cuttings with ''callus''. Trough the resultS obtained, it was concluded that, for obtaining more rooting of cuttings, the best treatment was NAA at 200 ppm plus boron or, the combination of IBA and NAA at 200 ppm plus boron.

Boron translocation in coffee trees

Boron deficiency in coffee trees ( Coffea arabica) is widespread, however, responses to B fertilizer have been erratic, depending on the year, method, and time of application. A better understanding of B uptake, distribution, and remobilization within the plant is important in developing a rational fertilization program. Field and greenhouse experiments were conducted to study B distribution and remobilization in coffee trees. Boron was provided either in the nutrient solution or sprayed on the leaves of trees grown under adequate or transient B deficiency. There was clear evidence for B translocation via symplast ( remobilization) to coffee grains, even in well-nourished plants. When 10 B was present in the nutrient solution during most part of fruit filling, from 33 to 40% of the B found in coffee fruits was absorbed during this period, depending on the timing and duration of the B deficiency treatment. In the field, when B was sprayed once on the leaves, around 4% of the fruit B was derived from the foliar fertilizer. Boron remobilization within coffee trees is limited in well nourished plants, but it can be significant during periods of temporary B deficiency in plants otherwise well nourished with B. The implications of these findings for B fertilization practice, are discussed.

Zirconia needles synthesized inside hexagonal swollen liquid crystals

We report the synthesis of zirconia microneedles by the direct nucleation of particles inside a hexagonal swollen liquid crystal (SLC) (cell parameter a = 27 nm) prepared by mixing with the proper ratio, an aqueous solution of sulfated zirconium colloids, a cationic surfactant (cetylpyridinium chloride), cychlohexane as swelling agent with an oil over water ratio of 2.5 (vol.), and 1-pentanol as cosurfactant. After a slow crystallogenesis that can be enhanced by an initial induction step under moderate temperature, particles in the centimeter range can be obtained, with a very high shape ratio (over 100). These particles are made of crystalline octahydrate zirconium oxychloride containing pores of 20 nm diameter, aligned along the main axis of the liquid crystal, as the fingerprint of the oil cylinders present in the hexagonal phase. The morphology of these particles confirms that the shaping mechanism is based on true liquid crystal templating (TLCT). Further thermal treatment of these particles, after extraction from the SLC, leads to the crystallization of zirconia with the same needlelike morphology as the zirconium oxychloride.

Effect of boron powder purity on superconducting properties of MgB2

The effect of the properties of starting boron powders on the superconducting properties of MgB2 has been studied. The 92% and 96% pure powders produce lower surface reactivity and larger particle size than the 99% boron powder, as can be seen from Brunauer - Emmett - Teller (BET) and scanning electron microscopy (SEM) results, indicating that the low purity powders cannot be used to archive the same superconducting properties as those of samples made from pure 99% boron powder. However, the purity of 92% and 96% boron powders can be improved by using a simple chemical process, leading to enhanced magnetic critical current densities J(c). From x-ray diffraction (XRD) measurement, oxide impurity has been observed, which might be originated from the B2O3 phase in the boron powders. In order to get high performance MgB2, it is obviously important to control the phase composition and microstructure of amorphous boron starting powders and solid reaction conditions.

The azomethine-H modified colorimetric method of boron determination at fertilizers.

The present work studied the azomethine-H colorimetric method for boron determination to fertilizers analysis applications. The reagent azomethine-H needs lights conditions of reaction that, jointed to the big sensibility and specificity, diffused its use in boron's dosage in many materials. The most suitable experimental parameters were established for such colorimetry, and analysis conditions: standard curve between 0,200 e 2,25 mg. L(-1) boron, in maximum absorption at 415nm, I cm cell and reading between 30 and 90 minutes standing after the final homogenization of the boron's solution in analyse and with dye reactive (azomethine If 0,90 % m/v solution at buffer ammonium acetate 1,82 mol . L(-1) - potassium acetate 0,10 mol . L(-1) - acetic acid 1,67 mol . L(-1)-EDTA 2,7 . 10(-2) mol . L(-1)-NTA 2,1.10(-2) mol . L(-1) pH 5,5). Statistics analysis of the results didn't present big differences when the same results were got by the colorimetric method offered and by the potentiometric, from AOAG, whatever in manufactured fertilizers or in lab sintetized fertilizers.

Effects of auxins and boron on rooting of kiwi stem cuttings (Actinidia chinensis Pl cv Matua)

This work studies the effects of some synthetical auxins and boron in the rooting of stem cuttings of kiwi (Actinidia chinensis Planch cv Matua). The stems used had two nodes and two leaves cut in half. The auxin effect was observed through seven different treatments: T1 (H2O); T2 (NAA 300 ppm); T3 (IBA 300 ppm); T4 (NAA 300 ppm + B); T5 (IBA 300 ppm + B); T6 (NAA 0,5%-talc) and T7 (IBA 0,5%-talc), applied to the bases of stem cuttings. After these treatments, the cuttings were placed in suitable rooting dishes, with pure vermiculite in misty nebulization chamber for 120 days until collection day. The evaluation of auxin and boric acid effects were made based on the following observations: 1. The percentage of rooted stem cuttings; 2. reducing sugar and total sugar analyses; and 3. tryptophan analyses. The effects of such treatments were observed in the four seasons. The results showed that winter is best for rooting. Application of IBA talc 0,5% to the cuttings bases increased rooting.

Action of auxins, boron and harvest season on the rooting of kiwi fruit stem cuttings (Actinidia chinensis Pl cv Monty)

Action of auxins on the rooting of stem cuttings of kiwi (Actinidia chinensis P. cv Monty). This work studies the effects of some synthetic auxins and B in the rooting of kiwi (Actinidia chinensis Planch cv Monty) stem cuttings. The treatments used were as follows: T1 (H2O); T2 (NAA 300 ppm); T3 (IBA 300 ppm); T4 (NAA 300 ppm + B); T5 (IBA 300 ppm + B); T6 (NAA 0,5%-talc) and T7 (IBA 0,5%-talc), applied to the bases of the cuttings. These were then placed in rooting dishes with pure vermiculite in a misty nebulization chamber until collection day (120 days). The evaluation of auxin and boric acid effects on kiwi stem cuttings were made based on the following observations: 1. The percentage of rooted stem cuttings; 2. reducing sugars and total sugar analyses (in g/100 g of dry matter); and 3. tryptophan analyses (in mu g/100 mg of dry matter). The results show that summer is the best season for rooting Actinidia chinensis Planch cv Monty stem cuttings. The use of IBA talc 0,5% on the bases of the cuttings shamed positive results too.

Boron deficiency inhibits petiole and peduncle cell development and reduces growth of cotton

The effect of boron (B) on cotton growth and fruit shedding may be due not only to physiological or biochemical effects, but also to vascular tissue malformation. This experiment investigated petiole and floral peduncle anatomical alterations and growth of cotton supplied with deficient and sufficient B in nutrient solution. Cotton (Gossypium hirsutum cv. 'Delta Opal') plants were grown in solutions containing 0, 1.5, 3.0, 4.5, and 6.0 mu mol L-1 of B from 22 to 36 d after plant emergence (DAPE). From 36 to 51 DAPE, B was omitted from the nutrient solution. Petioles from young leaves and floral bud peduncles (first position of the first sympodial) were sampled and the cross-section anatomy observed under an optical microscope. The number of vascular bundles of the petiole was decreased in B-deficient plants and the xylem was disorganized. Phloem elements in the peduncle vascular cylinder of B-deficient plants did not show clear differentiation. The few xylem elements that were formed were also disorganized. Modifications caused by B deficiency may have impaired B and photosynthate translocation into new cotton growth. Boron accumulation in the shoot of B-deficient plants suggested that there was some B translocation within the plant. It could be inferred that cotton growth would be impaired by the decrease in carbohydrate translocation rather than by B deficiency in the tissue alone.

Electron field emission from boron doped microcrystalline diamond

Field emission properties of hot filament chemical vapor deposited boron doped polycrystalline diamond have been studied. Doping level (N-B) of different samples has been varied by the B/C concentration in the gas feed during the growth process and doping saturation has been observed for high B/C ratios. Threshold field (E-th) for electron emission as function of B/C concentration has been measured, and the influences of grain boundaries, doping level and surface morphology on field emission properties have been investigated. Carrier transport through conductive grains and local emission properties of surface sites have been figured out to be two independent limiting effects in respect of field emission. Emitter current densities of 500 nA cm(-2) were obtained using electric fields less than 8 V/mu m. (c) 2007 Elsevier B.V. All rights reserved.

Controlled growth of anodic aluminium oxide films with hexagonal array of nanometer-sized pores filled with textured copper nanowires

Anodic aluminium oxide (AAO) films exhibiting a homogeneous morphology of parallel pores perpendicular to the surface were prepared in a two-step anodization process and filled with copper by electrochemical deposition. The optimum growth conditions for the formation of freestanding AAO films with hexagonal compact array of cylindrical pores were studied by field emission scanning electron microscopy and small angle X-ray scattering. The results show well-defined periodic structures with uniform pores size distribution for films with pore diameters between 40 and 70 nm prepared using different voltages and temperatures during the second anodization step. X-ray photoelectron spectroscopy and X-ray diffraction analysis of AAO films filled with copper show the formation of nanowires with high structural order, exhibiting a preferential crystalline orientation along the (2 2 0) axis and only small fraction of copper oxides. The best results for textured Cu nanowires were obtained at a reduction potential of -300 mV. (C) 2009 Elsevier Ltd. All rights reserved.

Hexagonal-shaped tin glycolate particles: A preliminary study of their suitability as li-ion insertion electrodes

Tin glycolate particles were prepared by a simple, one-step, polyol-mediated synthesis in air in which tin oxalate precursor was added to ethylene glycol and heated at reflux. Hexagonal-shaped, micron-sized tin glycolate particles were formed when the solution had cooled. A series of tin oxides was produced by calcination of the synthesized tin glycolate at 600-800 degrees C. It was revealed that the micron-sized, hexagonal-shaped tin glycolate now consisted of nanosized tin-based particles (80-120 nm), encapsulated within a tin glycolate shell. XRD, TGA, and FT-IR measurements were conducted to account for the three-dimensional growth of the tin glycolate particles. When applied as an anode material for Li-ion batteries, the synthesized tin glycolate particles showed good electro-chemical reactivity in Li-ion insertion/ deinsertion, retaining a specific capacity of 416mAhg(-1) beyond 50cycles. Ibis performance was significantly better than those of all the other tin oxides nanoparticles (< 160mAhg(-1)) obtained after heat treatment in air. We strongly believe that the buffering of the volume expansion by the glycolate upon Li-Sn alloying is the main factor for the improved cycling of the electrode.

Cotton growth and boron distribution in the plant as affected by a temporary deficiency of boron

The knowledge of nutrient mobility is an important tool to define the best fertilizer management and diagnosis techniques. Patterns of boron (B) mobility in plants have been reviewed, but there is very little information on B distribution and mobility in cotton. An experiment was conducted to study plant growth and B distribution in cotton when the nutrient was applied in the nutrient solution or to the leaves, and when a temporary deficiency was imposed. Cotton (Gossypium hirsutum, Latifolia, cv. IAC 22) was grown in nutrient solutions where B was omitted or not for 15 days. Boron was applied to young or mature cotton leaves in some of the minus B treatments. Root growth decreased when the plants were transferred to B solutions, but there was a full recovery when B was replaced in the nutrient medium. Boron deficiency, even when temporary, reduced cotton shoot dry matter yields, plant height and flower and fruit set, and these could not be prevented by foliar application of B. Because of decreased dry matter production, leaves of deficient cotton plants actually showed higher B concentrations than non deficient leaves. This would be misleading when a mature leaf is sampled for diagnosis. If there is any B mobility in cotton phloem, it is very low.

Effect of Boron powder purity on superconducting properties of bulk MgB2

In order to study the influence of the amorphous Boron powder on the superconducting properties, MgB2 bulk samples were prepared using 96% and 99% pure commercial Boron powder as well as 92% commercial Boron powder after purification process. The results showed that the original 96% and the purified 92% powders have larger particle size compared to the pure 99% Boron powder, which leads to reduce magnetic critical current densities. In order to get higher performance MgB2, the purified low grade Boron powder need further control of their microstructure such as smaller particle size to enhance flux pinning from the grain boundaries which represent effective pinning centers. © 2007 Elsevier B.V. All rights reserved.