Geotechnical properties of Lau Basin sediments

Distribution of pore space and degree of cementation appear to be the main factors controlling the permeability of sediments retrieved from the Lau Basin. The undisturbed microfabrics of two lithologies, nannofossil ooze and vitric sandy silt, commonly found at Holes 834A, 835A, 838A, and 839Aof Leg 135 were examined by scanning electron microscopy equipped with energy dispersive X-ray spectral analysis and image analysis systems. The results of these analyses were compared with laboratory determinations of porosity, grain-size distribution, and permeability on discrete samples from the same sediment depths. The permeability of the vitric sandy silt is 3-5 orders of magnitude higher than the nannofossil ooze samples. The porosity of nannofossil ooze ranges from 6% to 12% greater than the porosity of vitric sandy silt, which partially reflects the finer texture of nannofossil ooze. Although the correlation of higher porosity with lower permeability is not surprising, factors other than simply grain-size distribution must be invoked to explain the large differences in permeability found in these samples.

In-situ geotechnical measurements with the dynamic penetrometer Nimrod on the continental shelf off the Coromandel Peninsula, New Zealand

We tested the ability of a small dynamic penetrometer, Nimrod, to infer geotechnical properties of sediment mixtures in the inner shelf. The penetrometer is light and easy to operate, and its operation by scuba divers ensures a greater degree of precision than ship-based penetrometer deployments. We have studied selected positions along a sorted bedform (~ 100 m wide) on the continental shelf off the Coromandel Peninsula close to Tairua, North Island of New Zealand, and additionally took sediment samples at the exact positions of penetrometer impact, also by scuba divers. The derived dynamic penetrometer signatures (i) measured deceleration of the probe and estimated quasi-static bearing capacity as a measure of sediment strength, (ii) reflected changes in grain-size distribution ranging from very fine to very coarse sands, and (iii) revealed the uppermost seafloor stratification (top layer 2-6 cm) potentially being an indicator for sediment dynamics. In this manner, the device proved to be suitable for spatially fine-scaled surveys using divers' support and might deliver complementary information about sediment dynamics, in this case sorted-bedform maintenance.

Geotechnical properties of sediments at DSDP Site 75-532

During Leg 75 of the Deep Sea Drilling Project (DSDP) from the D/V Glomar Challenger, a 200-m deep hole was drilled at Hole 532A on the eastern side of Walvis Ridge at a water depth of 1331 m. Sediment cores were obtained by means of a hydraulic piston corer. All of the cores from this boring were designated for geotechnical studies and were distributed among eight institutions. The results of laboratory studies on these sediment cores were compiled and analyzed. Sediment properties, including physical characteristics, strength, consolidation, and permeability were studied to evaluate changes as a function of depth of burial. It was concluded that the sediment profile to the explored depth of 200 m at Walvis Ridge consists of approximately 50 m of foram-nannofossil marl (Subunit 1a) over 64 m of diatom-nannofossil marl (Subunit 1b) over nannofossil marl (Subunit 1c) to the depth explored. All three sediment units appear to be normally consolidated, although some anomalies seem to exist to a depth of 120 m. No distinct differences were found among the sediment properties of the three subunits (1a, 1b, and 1c) identified at this site.

Range charts of stratigraphically important radiolarian species in sediments of ODP Leg 165 sites

The Paleogene sequences from three sites in the Caribbean were examined for radiolarians. In general, samples are highly lithified, requiring lengthy and repetitive cleaning procedures, and the assemblages are usually fragmented and/or partially dissolved. Both abundances and preservation of the assemblages vary considerably from site to site and within a single site; even within a single sample more than one degree of preservation was observed. It was possible, however, to construct at least partial stratigraphies for each of the three sites. Because the abundance of radiolarians is high even in extremely poorly preserved assemblages, we conclude that the differences in biogenic silica preservation are the result of postdepositional processes and not productivity. In both Sites 999 and 1001, near the Paleocene/Eocene boundary (Bekoma bidartensis Zone [RP7]), there is a short interval in which the abundance and preservation state of the radiolarians improves relative to overlying and underlying assemblages. In each case the intervals corresponds to the level, identified by calcareous microfossils, as representing changes in paleoceanographic conditions associated with the late Paleocene thermal maximum.