List of chemical compounds authorized for use under USDA inspection and grading programs /

Description based on: 1981.

Lumber distribution and consumption.

Compiled by R.V. Reynolds and A.H. Pierson, Division of Forest Economics, Forest Service, U.S. Dept. of Agriculture, in cooperation with the U.S. Bureau of the Census and the Canada Dominion Bureau of Statistics, Forest Products Branch.

Bibliography of wood distillation, 1907-1953.

Mode of access: Internet.

Biomass estimates of eastern redcedar tree components /

"February 1976."

Classroom demonstrations of wood properties,

Mode of access: Internet.

The Log of the Lab

Mode of access: Internet.

Modern connectors for timber construction.

"By Nelson S. Perkins, construction engineer, Peter Landsem, assistant construction engineer, National Committee on Wood Utilization, United States Department of Commerce, and Geo. W. Trayer, senior engineer, Forest Products Laboratory, Branch of Research, Forest Service, United States Department of Agriculture."--P.1.

Research Program

Title Varies: Program of Work

Special Report

Mode of access: Internet.

Leaf morphology scales multi-annual trends in nutrient cycling and leaf, flower, and fruiting phenology among species in the sub-tropical hardwood forests of the northern Florida Keys

The subtropical hardwood forests of southern Florida are formed by 120 frost-sensitive, broadleaved angiosperm species that range throughout the Caribbean. Previous work on a series of small sized forest component patches of a 20 km2, forest preserve in northern Key Largo indicate that a shift in species composition was associated with a 100 year forest developmental sequence, and this shift was associated with an increasingly evergreen canopy. This document investigates the underlying differences of the biology of trees that live in this habitat, and is specifically focused on the impact of leaf morphology on changing nutrient cycling patterns. Measurements of the area, thickness, dry mass, nutrient content and longevity of several leaves from 3-4 individuals of ten species were conducted in combination with a two-year leaf litter collection and nutrient analysis to determine that species with thicker, denser leaves cycled scarce nutrients up to 2-3 times more efficiently than thin leaved tree species, and the leaf thickness/density index predicts role in forest development in a parallel direction as the index predicts nutrient cycling efficiency. A three year set of observations on the relative abundance of new leaves, flowers and fruits of the same tree species provides an opportunity to evaluate the consequences the leaf morphology/nutrient cycling/forest development relationship to forest habitat quality. Results of the three documents support a mechanistic link between forest development and nutrient cycling, and suggests that older forests are likely to be better habitats based on the availability of valuable forest products like new leaves, flowers, and fruits throughout the year.

Avaliação da potencialidade de incorporação de um lodo de uma indústria de produtos de limpeza como adição mineral em concretos de cimento Portland

The generation of industrial wastes has been increased more and more in recent decades, motivating studies about a correct sustainable allocation and that also represents advantages for their generators. In this context, are included two companies of cleaning products niche, located in São José do Mipibu/RN, that produces industrial sludge at a sewage treatment plant, and that is the main approach of this research. Given this, it was studied the incorporation potentiality of this sludge as a mineral addition in cement matrix for concrete production due it high capacity of wastes immobilization inside this material, which are subsequently used in the company for making precast articles. Were added different sludge concentrations (5, 10, 15 and 20%) in a common trait (1: 2: 3), and evaluated their techniques and microstructural implications via workability test in fresh state and compressive strength, full porosity and scanning electron microscopy (SEM) in the hardened state. The results demonstrated the feasibility of the process both from a technical and environmental view as economical. All concretes produced with residue showed an increase of workability given the nature of the waste that had surfactants substances capable of adsorbing tiny particles of air into the batter. However, for all concentrations were obtained lower compressive resistances than standard concrete, with a reduction of 39% for samples with 20% of sludge. This are attributed mainly to an increase of porosity in the transition zone of these material, resulting from increased formation of ettringite at the detriment to the formation of other compounds, but which still allows the use of these for the manufacture of concrete articles with non-structural nature, such as precast floor. In addition, the water absorption and void ratio increased slightly for all samples, except the concrete with 20% of waste that has a reduction for the last parameter. Given this context, the recommended maximum level is 20%, constituting a significant proportion and able to allocate sustainably all waste generated in the industry.

Of Marx and Makers: an Historical Perspective on Generative Justice

In Marxist frameworks “distributive justice” depends on extracting value through a centralized state. Many new social movements—peer to peer economy, maker activism, community agriculture, queer ecology, etc.—take the opposite approach, keeping value in its unalienated form and allowing it to freely circulate from the bottom up. Unlike Marxism, there is no general theory for bottom-up, unalienated value circulation. This paper examines the concept of “generative justice” through an historical contrast between Marx’s writings and the indigenous cultures that he drew upon. Marx erroneously concluded that while indigenous cultures had unalienated forms of production, only centralized value extraction could allow the productivity needed for a high quality of life. To the contrary, indigenous cultures now provide a robust model for the “gift economy” that underpins open source technological production, agroecology, and restorative approaches to civil rights. Expanding Marx’s concept of unalienated labor value to include unalienated ecological (nonhuman) value, as well as the domain of freedom in speech, sexual orientation, spirituality and other forms of “expressive” value, we arrive at an historically informed perspective for generative justice. 

Automatisation de la fonction de façonnage de deux têtes d’abatteuses-façonneuses : Effets sur la productivité et le taux de conformité des billes façonnées

Pour rester compétitives, les entreprises forestières cherchent à contrôler leurs coûts d’approvisionnement. Les abatteuses-façonneuses sont pourvues d’ordinateurs embarqués qui permettent le contrôle et l’automatisation de certaines fonctions. Or, ces technologies ne sont pas couramment utilisées et sont dans le meilleur des cas sous-utilisées. Tandis que l’industrie manifeste un intérêt grandissant pour l’utilisation de ces ordinateurs, peu de travaux de recherche ont porté sur l’apport en productivité et en conformité aux spécifications de façonnage découlant de l’usage de ces systèmes. L’objectif de l’étude était de mesurer les impacts des trois degrés d’automatisation (manuel, semi-automatique et automatique) sur la productivité (m3/hmp) et le taux de conformité des longueurs et des diamètre d’écimage des billes façonnées (%). La collecte de données s’est déroulée dans les secteurs de récolte de Produits forestiers résolu au nord du Lac St-Jean entre les mois de janvier et d’août 2015. Un dispositif en blocs complets a été mis en place pour chacun des cinq opérateurs ayant participé à l’étude. Un seuil de 5 % a été employé pour la réalisation de l’analyse des variances, après la réalisation de contrastes. Un seul cas a présenté un écart significatif de productivité attribuable au changement du degré d’automatisation employé, tandis qu’aucune différence significative n’a été détectée pour la conformité des diamètres d’écimage; des tendances ont toutefois été constatées. Les conformités de longueur obtenues par deux opérateurs ont présenté des écarts significatifs. Ceux-ci opérant sur deux équipements distincts, cela laisse entrevoir l’impact que peut aussi avoir l’opérateur sur le taux de conformité des longueurs.