An investigation of rail condition monitoring by Fibre Bragg Grating sensors

Condition monitoring on rails and train wheels is vitally important to the railway asset management and the rail-wheel interactions provide the crucial information of the health state of both rails and wheels. Continuous and remote monitoring is always a preference for operators. With a new generation of strain sensing devices in Fibre Bragg Grating (FBG) sensors, this study explores the possibility of continuous monitoring of the health state of the rails; and investigates the required signal processing techniques and their limitations.

Measurement of temperature and pressure on the surface of a blunt cone using FBG sensor in hypersonic wind tunnel

Measurement of temperature and pressure exerted on the leeward surface of a blunt cone specimen has been demonstrated in the present work in a hypersonic wind tunnel using fiber Bragg grating (FBG) sensors. The experiments were conducted on a 30 degrees apex-angle blunt cone with 51 mm base diameter at wind flow speeds of Mach 6.5 and 8.35 in a 300 mm hypersonic wind tunnel of Indian Institute of Science, Bangalore. A special pressure insensitive temperature sensor probe along with the conventional bare FBG sensors was used for explicit temperature and aerodynamic pressure measurement respectively on the leeward surface of the specimen. computational fluid dynamics (CFD) simulation of the flow field around the blunt cone specimen has also been carried out to obtain the temperature and pressure at conditions analogous to experiments. The results obtained from FBG sensors and the CFD simulations are found to be in good agreement with each other.

Ultra sensitive NO2 gas detection using the reduced graphene oxide coated etched fiber Bragg gratings

We report a simple and highly sensitive methodology for the room temperature NO2 gas sensing using reduced graphene oxide (RGO) coated clad etched fiber Bragg grating (eFBG). A significant shift (>10 pm) is observed in the reflected Bragg wavelength (lambda(B)) upon exposing RGO coated on the surface of eFBG to the NO2 gas molecules of concentration 0.5 ppm. The shift in Bragg wavelength is due to the change in the refractive index of RGO by charge transfer from the adsorbing NO2 molecules. The range of NO2 concentration is tested from 0.5 ppm to 3 ppm and the estimated time taken for 50% increase in Delta lambda(B) ranges from 20 min (for 0.5 ppm) to 6 min (for 3 ppm). (C) 2015 Elsevier B.V. All rights reserved.

FBG pressure sensor based on the double shell cylinder with temperature compensation

A novel fiber Bragg grating (FBG) pressure sensor based on the double shell cylinder with temperature compensation is presented. in the sensing scheme, a sensing FBG is affixed in the tangential direction on the outer surface of the inner cylinder, and another FBG is affixed in the axial direction to compensate the temperature fluctuation. Based on the theory of elasticity, the theoretical analysis of the strain distribution of the sensing shell is presented. Experiments are carried out to test the performance of the sensor. A pressure sensitivity of 0.0937 nm/MPa has been achieved. The experimental results also demonstrate that the two FBGs have the same temperature sensitivity, which can be utilized to compensate the temperature induced wavelength shift during the pressure measurement. (C) 2008 Elsevier Ltd. All rights reserved.

Temperature-independent FBG pressure sensor with high sensitivity

This study develops a fiber Bragg grating (FBG) pressure sensor partly shielded with a metal tube. The thermal-strain cross effect is avoided and its pressure sensitivity is increased to -2.44 x 10(-3) MPa, about 1200 times as that of a bare fiber grating. Due to its good sensing linearity, this sensor can be applied in the measurement of hydraulic pressure and vibration. (c) 2006 Elsevier Inc. All rights reserved.

Experiment on Qinghai-Tibet railroad subgrade temperature monitoring based on FBG sensors

Qinghai-Tibet Railway is the longest and highest plateau railway in the world. A long term monitoring system of the stability of the subgrade in the permafrost regions should be put forward immediately to prevent damage to the railway. As it's very difficult to set up the long-distance automatic monitoring system which contains a lot of measure points along the 550 kilometers railway in the permafrost area, we present a subgrade temperature monitor system based on fiber Bragg grating (FBG). In this paper the principles of the FBG was presented, and the feasibility of the FBG sensors in the permafrost area of Qinghai-Tibet plateau was analysized. We embedded fifteen FBG temperature sensors and thermal resistance temperature sensors. A contrast experiment is made while the two kinds of sensors are arranged in the same position. The result of the experiment shows that the accuracy of the FBG temperature sensors is less than 0.1 degrees C. and the FBG sensors can do well in the measurement of pattern which the temperature varies with the depth of the permafrost soil. The result also shows the stability of the FBG sensors in the bad environmental condition of Qinghai-Tibet plateau, which proves the feasibility of the application of FBG sensors and our monitoring system on the Qinghai-Tibet railway.

In situ cross-calibration of in-fibre Bragg Grating and Electrical Resistance Strain Gauges for structural monitoring using an extensometer

Special issue on Sensor Systems for Structural Health Monitoring Abstract—This study addresses the direct calibration of optical fiber strain sensors used for structural monitoring and is carried out in situ. The behavior of fiber-Bragg-grating-based sensor systems when attached to metal bars, in a manner representative of their use as reinforcement bars in structures, was examined and their response calibrated. To ensure the validity of the measurements,this was done using an extensometer with a further calibrationagainst the response of electrical resistance strain gauges, often conventionally used, for comparison. The results show a repeatable calibration generating a suitable geometric factor of extension to strain for these sensors, to enable accurate strain data to be obtained when the fiber-optic sensor system is in use in structural monitoring applications.

Aplicações das redes de Bragg na biomecânica

O presente trabalho tem como objectivo o estudo, desenvolvimento e aplicações na área da biomecânica de sensores intrínsecos baseados em redes de Bragg em fibras ópticas (FBG). As aplicações são feitas em modelos biomecânicos in vitro tais como: implantes de anca, prótese de joelho, placas de osteossíntese e implantes dentários. A optimização do desenvolvimento de próteses e respectivos elementos de fixação é actualmente dependente da geração e validação experimental de seus modelos computacionais. A validação destes modelos é normalmente feita utilizando-se dados de ensaios não invasivos e invasivos em modelos sintéticos. Em ensaios in vitro os sensores convencionais têm um princípio de funcionamento eléctrico e apresentam por vezes dimensões inadequadas. Existem situações exploradas no presente trabalho, tais como sensoriamento de superfícies irregulares e junções ou ainda análises de deformações internas, onde é recomendável a utilização de sensores FBG, pois apresentam dimensões reduzidas e flexibilidade o que permite efectuar medidas localizadas. O desenvolvimento de um protocolo de utilização de FBG e a sua aplicação no contexto apresentado demonstrou-se mais adequado, pela precisão e segurança futura oferecidas. Foi desenvolvida uma metodologia experimental para medidas de deformações utilizando FBG ao longo de uma placa de osteossíntese metálica aparafusada a um fémur sintético fracturado. Foi efectuada a monitorização da cura do cimento ósseo utilizado como fixador do prato tibial na artroplastia total do joelho através da medida da sua contracção e temperatura. Foi também desenvolvido um sistema refrigerador com resposta às leituras de temperatura com vista a evitar a necrose do osso. Foram efectuados estudos de deformação nesse cimento após a sua cura, como resultado da aplicação de cargas mecânicas estáticas. Foram efectuados estudos da cura de cimento ósseo aplicado a próteses de anca e também de deformações nestas próteses. Foi ainda efectuado o estudo comparativo de vários implantes dentários através da medida da distribuição de deformações como resposta a excitações mecânicas impulsivas. Para a desmodulação das FBG foram inicialmente utilizados sistemas comerciais. Entretanto algumas aplicações não puderam ser implementadas com estes sistemas comerciais devido à baixa reflectividade das FBG utilizadas, mas fundamentalmente devido à necessidade de executar testes com uma taxa de aquisição maior do que os 5 Hz disponíveis (cerca de 15 kHz). Por estes motivos foi desenvolvido um sistema optoelectrónico completo de desmodulação de FBG baseado num filtro sintonizável e que tem como característica principal a alta taxa de aquisição (até 1,2 MHz) mas também se destaca pela facilidade na reconfiguração dos parâmetros de leitura, pela apresentação duma interface de utilizador amigável e pela capacidade de operar com até 5 FBG na mesma fibra óptica.

Optical fiber accelerometer system for structural dynamic monitoring

In this study, the implementation of an optical accelerometer unit based on fiber Bragg gratings, suitable to monitor structures with frequencies up to 45 Hz, is reported. The developed optical system was used to estimate the structure eigenfrequencies of a steel footbridge, with a total length of 300 m, over the Sao Pedro Creek, located at University of Aveiro Campus, in Portugal. The acceleration records measured with this solution are compared with those obtained by traditional commercial electronic devices, revealing a root-mean-square error of 2.53 x 10(-5) G.

Analysis and Testing of a Novel Oadm Based on FBG and Machzehnder Interferometer

A novel optical add-drop multiplexer (OADM) based on the Mach-Zelauler interferometer (MZI) and the fiber Bragg grating (FBG) is proposed for the first tittle to the authors ' knowledge. In the structure, the Mach-Zehnder interferometer acts as an optical switch. The principle of the OADM is analyzed in this paper. The OADM can add/drop one of the multi-input channels or pass the channel directly by adjusting the difference of the two arms of the interferometer. The channel isolation is more than 20 dB

FBG optimization using spline encoded evolution strategy

ABSTRACT: This paper presents an encoding scheme adapted for Fiber Bragg Grating (FBG) optimization using metaheuristics. The proposed encoding scheme uses spline approximations in order to build softened refractive index profiles from few encoded parameters. This approach is suitable for Fiber Bragg Grating (FBG) synthesis because it ensures both the reduction of the problem dimensionality and the respect of important restrictions associated to the FBG manufacture. Simulations are shown where an ES using the spline encoding was able to converge faster and produce more interesting filters, when compared with conventional encoding schemes.

Integrating optical fiber force sensors into microforceps for ORL microsurgery

The delicate anatomy of the ear require surgeons to use great care when operating on its internal structures. One example for such an intervention is the stapedectomy, where a small crook shaped piston is placed in the oval window of the cochlea and connected to the incus through crimping thus bypassing the diseased stapes. Performing the crimp process with the correct force is necessary since loose crimps poorly transmit sound whereas tight crimps will eventually result in necrosis of the incus. Clinically, demand is high to reproducibly conduct the crimp process through a precise force measurement. For this reason, we have developed a fiber Bragg grating (FBG) integrated microforceps for use in such interventions. This device was calibrated, and tested in cadaver preparations. With this instrument we were able to measure for the first time forces involved in crimping a stapes prosthesis to the incus. We also discuss a method of attaching and actuating such forceps in conjunction with a robot currently under development in our group. Each component of this system can be used separately or combined to improve surgical accuracy, confidence and outcome.

Yellow laser light generation by frequency doubling of the output from a master oscillator fiber power amplifier system

We present a power-scalable approach for yellow laser-light generation based on standard Ytterbium (Yb) doped fibers. To force the cavity to lase at 1154 nm, far above the gain-maximum, measures must be taken to fulfill lasing condition and to suppress competing amplified spontaneous emission (ASE) in the high-gain region. To prove the principle we built a fiber-laser cavity and a fiber-amplifier both at 1154 nm. In between cavity and amplifier we suppressed the ASE by 70 dB using a fiber Bragg grating (FBG) based filter. Finally we demonstrated efficient single pass frequency doubling to 577 nm with a periodically poled lithium niobate crystal (PPLN). With our linearly polarized 1154 nm master oscillator power fiber amplifier (MOFA) system we achieved slope efficiencies of more than 15 % inside the cavity and 24 % with the fiber-amplifier. The frequency doubling followed the predicted optimal efficiency achievable with a PPLN crystal. So far we generated 1.5 W at 1154nm and 90 mW at 577 nm. Our MOFA approach for generation of 1154 nm laser radiation is power-scalable by using multi-stage amplifiers and large mode-area fibers and is therefore very promising for building a high power yellow laser-light source of several tens of Watt.

Single uniform FBG for simultaneous measurement of liquid level and temperature

In this paper, we propose and demonstrate a novel scheme for simultaneous measurement of liquid level and temperature based on a simple uniform fiber Bragg grating (FBG) by monitoring both the short-wavelength-loss peaks and its Bragg resonance. The liquid level can be measured from the amplitude changes of the short-wavelength-loss peaks, while temperature can be measured from the wavelength shift of the Bragg resonance. Both theoretical simulation results and experimental results are presented. Such a scheme has some advantages including robustness, simplicity, flexibility in choosing sensitivity and simultaneous temperature measurement capability.

Extended range interrogation of wavelength division multiplexed fibre Bragg grating sensors using an arrayed waveguide grating

A technique for interrogating multiplexed fibre Bragg grating (FBG) sensors using an arrayed waveguide grating (AWG) is described. The approach considerably extends the sensing range from that achieved previously, while providing a strain resolution of 17nevHz at 30 Hz.