Development of Preliminary Load and Resistance Factor Design of Drilled Shafts in Iowa, RB03-012, 2014

The Federal Highway Administration (FHWA) mandated utilizing the Load and Resistance Factor Design (LRFD) approach for all new bridges initiated in the United States after October 1, 2007. To achieve part of this goal, a database for Drilled Shaft Foundation Testing (DSHAFT) was developed and reported on by Garder, Ng, Sritharan, and Roling in 2012. DSHAFT is aimed at assimilating high-quality drilled shaft test data from Iowa and the surrounding regions. DSHAFT is currently housed on a project website (http://srg.cce.iastate.edu/dshaft) and contains data for 41 drilled shaft tests. The objective of this research was to utilize the DSHAFT database and develop a regional LRFD procedure for drilled shafts in Iowa with preliminary resistance factors using a probability-based reliability theory. This was done by examining current design and construction practices used by the Iowa Department of Transportation (DOT) as well as recommendations given in the American Association of State Highway and Transportation Officials (AASHTO) LRFD Bridge Design Specifications and the FHWA drilled shaft guidelines. Various analytical methods were used to estimate side resistance and end bearing of drilled shafts in clay, sand, intermediate geomaterial (IGM), and rock. Since most of the load test results obtained from O-cell do not pass the 1-in. top displacement criterion used by the Iowa DOT and the 5% of shaft diameter for top displacement criterion recommended by AASHTO, three improved procedures are proposed to generate and extend equivalent top load-displacement curves that enable the quantification of measured resistances corresponding to the displacement criteria. Using the estimated and measured resistances, regional resistance factors were calibrated following the AASHTO LRFD framework and adjusted to resolve any anomalies observed among the factors. To illustrate the potential and successful use of drilled shafts in Iowa, the design procedures of drilled shaft foundations were demonstrated and the advantages of drilled shafts over driven piles were addressed in two case studies.

Design of Piles for Integral Abutment Bridges, HR-252, 1984

More and more, integral abutment bridges are being used in place of the more traditional bridge designs with expansion releases. In this study, states which use integral abutment bridges were surveyed to determine their current practice in the design of these structures. To study piles in integral abutment bridges, a finite element program for the soil-pile system was developed (1) with materially and geometrically nonlinear, two and three dimensional beam elements and (2) with a nonlinear, Winkler soil model with vertical, horizontal, and pile tip springs. The model was verified by comparison to several analytical and experimental examples. A simplified design model for analyzing piles in integral abutment bridges is also presented. This model grew from previous analytical models and observations of pile behavior. The design model correctly describes the essential behavioral characteristics of the pile and conservatively predicts the vertical load-carrying capacity. Analytical examples are presented to illustrate the effects of lateral displacements on the ultimate load capacity of a pile. These examples include friction and end-bearing piles; steel, concrete, and timber piles; and bending about the weak, strong, and 45° axes for H piles. The effects of cyclic loading are shown for skewed and nonskewed bridges. The results show that the capacity of friction piles is not significantly affected by lateral displacements, but the capacity of end-bearing piles is reduced. Further results show that the longitudinal expansion of the bridge can introduce a vertical preload on the pile.

Maintenance and Design of Steel Abutment Piles in Iowa Bridges, TR-622, 2014

Soil consolidation and erosion caused by roadway runoff have exposed the upper portions of steel piles at the abutments of numerous bridges, leaving them susceptible to accelerated corrosion rates due to the abundance of moisture, oxygen, and chlorides at these locations. This problem is compounded by the relative inaccessibility of abutment piles for close-up inspection and repair. The objective of this study was to provide bridge owners with recommendations for effective methods of addressing corrosion of steel abutment piles in existing and future bridges A review of available literature on the performance and protection of steel piles exposed to a variety of environments was performed. Eight potential coating systems for use in protecting existing and/or new piles were selected and subjected to accelerated corrosion conditions in the laboratory. Two surface preparation methods were evaluated in the field and three coating systems were installed on three piles at an existing bridge where abutment piles had been exposed by erosion. In addition, a passive cathodic protection (CP) system using sacrificial zinc anodes was tested in the laboratory. Several trial flowable mortar mixes were evaluated for use in conjunction with the CP system. For existing abutment piles, application of a protective coating system is a promising method of mitigating corrosion. Based on its excellent performance in accelerated corrosion conditions in the laboratory on steel test specimens with SSPC-SP3, -SP6, and -SP10 surface preparations, glass flake polyester is recommended for use on existing piles. An alternative is epoxy over organic zinc rich primer. Surface preparation of existing piles should include abrasive blast cleaning to SSPC-SP6. Although additional field testing is needed, based on the results of the laboratory testing, a passive CP system could provide an effective means of protecting piles in existing bridges when combined with a pumped mortar used to fill voids between the abutment footing and soil. The addition of a corrosion inhibitor to the mortar appears to be beneficial. For new construction, shop application of thermally sprayed aluminum or glass flake polyester to the upper portion of the piles is recommended.

Randomized comparison of biodegradable polymer sirolimus-eluting stents versus durable polymer everolimus-eluting stents for percutaneous coronary revascularization: Rationale and design of the BIOSCIENCE trial.

BACKGROUND: Biodegradable polymers for release of antiproliferative drugs from metallic drug-eluting stents aim to improve long-term vascular healing and efficacy. We designed a large scale clinical trial to compare a novel thin strut, cobalt-chromium drug-eluting stent with silicon carbide-coating releasing sirolimus from a biodegradable polymer (O-SES, Orsiro; Biotronik, Bülach, Switzerland) with the durable polymer-based Xience Prime/Xpedition everolimus-eluting stent (EES) (Xience Prime/Xpedition stent, Abbott Vascular, IL) in an all-comers patient population. DESIGN: The multicenter BIOSCIENCE trial (NCT01443104) randomly assigned 2,119 patients to treatment with biodegradable polymer sirolimus-eluting stents (SES) or durable polymer EES at 9 sites in Switzerland. Patients with chronic stable coronary artery disease or acute coronary syndromes, including non-ST-elevation and ST-elevation myocardial infarction, were eligible for the trial if they had at least 1 lesion with a diameter stenosis >50% appropriate for coronary stent implantation. The primary end point target lesion failure (TLF) is a composite of cardiac death, target vessel myocardial infarction, and clinically driven target lesion revascularization within 12 months. Assuming a TLF rate of 8% at 12 months in both treatment arms and accepting 3.5% as a margin for noninferiority, inclusion of 2,060 patients would provide more than 80% power to detect noninferiority of the biodegradable polymer SES compared with the durable polymer EES at a 1-sided type I error of 0.05. Clinical follow-up will be continued through 5 years. CONCLUSION: The BIOSCIENCE trial will determine whether the biodegradable polymer SES is noninferior to the durable polymer EES with respect to TLF.

EADock : design of a new molecular docking algorithm and some of its applications

3 Summary 3. 1 English The pharmaceutical industry has been facing several challenges during the last years, and the optimization of their drug discovery pipeline is believed to be the only viable solution. High-throughput techniques do participate actively to this optimization, especially when complemented by computational approaches aiming at rationalizing the enormous amount of information that they can produce. In siiico techniques, such as virtual screening or rational drug design, are now routinely used to guide drug discovery. Both heavily rely on the prediction of the molecular interaction (docking) occurring between drug-like molecules and a therapeutically relevant target. Several softwares are available to this end, but despite the very promising picture drawn in most benchmarks, they still hold several hidden weaknesses. As pointed out in several recent reviews, the docking problem is far from being solved, and there is now a need for methods able to identify binding modes with a high accuracy, which is essential to reliably compute the binding free energy of the ligand. This quantity is directly linked to its affinity and can be related to its biological activity. Accurate docking algorithms are thus critical for both the discovery and the rational optimization of new drugs. In this thesis, a new docking software aiming at this goal is presented, EADock. It uses a hybrid evolutionary algorithm with two fitness functions, in combination with a sophisticated management of the diversity. EADock is interfaced with .the CHARMM package for energy calculations and coordinate handling. A validation was carried out on 37 crystallized protein-ligand complexes featuring 11 different proteins. The search space was defined as a sphere of 15 R around the center of mass of the ligand position in the crystal structure, and conversely to other benchmarks, our algorithms was fed with optimized ligand positions up to 10 A root mean square deviation 2MSD) from the crystal structure. This validation illustrates the efficiency of our sampling heuristic, as correct binding modes, defined by a RMSD to the crystal structure lower than 2 A, were identified and ranked first for 68% of the complexes. The success rate increases to 78% when considering the five best-ranked clusters, and 92% when all clusters present in the last generation are taken into account. Most failures in this benchmark could be explained by the presence of crystal contacts in the experimental structure. EADock has been used to understand molecular interactions involved in the regulation of the Na,K ATPase, and in the activation of the nuclear hormone peroxisome proliferatoractivated receptors a (PPARa). It also helped to understand the action of common pollutants (phthalates) on PPARy, and the impact of biotransformations of the anticancer drug Imatinib (Gleevec®) on its binding mode to the Bcr-Abl tyrosine kinase. Finally, a fragment-based rational drug design approach using EADock was developed, and led to the successful design of new peptidic ligands for the a5ß1 integrin, and for the human PPARa. In both cases, the designed peptides presented activities comparable to that of well-established ligands such as the anticancer drug Cilengitide and Wy14,643, respectively. 3.2 French Les récentes difficultés de l'industrie pharmaceutique ne semblent pouvoir se résoudre que par l'optimisation de leur processus de développement de médicaments. Cette dernière implique de plus en plus. de techniques dites "haut-débit", particulièrement efficaces lorsqu'elles sont couplées aux outils informatiques permettant de gérer la masse de données produite. Désormais, les approches in silico telles que le criblage virtuel ou la conception rationnelle de nouvelles molécules sont utilisées couramment. Toutes deux reposent sur la capacité à prédire les détails de l'interaction moléculaire entre une molécule ressemblant à un principe actif (PA) et une protéine cible ayant un intérêt thérapeutique. Les comparatifs de logiciels s'attaquant à cette prédiction sont flatteurs, mais plusieurs problèmes subsistent. La littérature récente tend à remettre en cause leur fiabilité, affirmant l'émergence .d'un besoin pour des approches plus précises du mode d'interaction. Cette précision est essentielle au calcul de l'énergie libre de liaison, qui est directement liée à l'affinité du PA potentiel pour la protéine cible, et indirectement liée à son activité biologique. Une prédiction précise est d'une importance toute particulière pour la découverte et l'optimisation de nouvelles molécules actives. Cette thèse présente un nouveau logiciel, EADock, mettant en avant une telle précision. Cet algorithme évolutionnaire hybride utilise deux pressions de sélections, combinées à une gestion de la diversité sophistiquée. EADock repose sur CHARMM pour les calculs d'énergie et la gestion des coordonnées atomiques. Sa validation a été effectuée sur 37 complexes protéine-ligand cristallisés, incluant 11 protéines différentes. L'espace de recherche a été étendu à une sphère de 151 de rayon autour du centre de masse du ligand cristallisé, et contrairement aux comparatifs habituels, l'algorithme est parti de solutions optimisées présentant un RMSD jusqu'à 10 R par rapport à la structure cristalline. Cette validation a permis de mettre en évidence l'efficacité de notre heuristique de recherche car des modes d'interactions présentant un RMSD inférieur à 2 R par rapport à la structure cristalline ont été classés premier pour 68% des complexes. Lorsque les cinq meilleures solutions sont prises en compte, le taux de succès grimpe à 78%, et 92% lorsque la totalité de la dernière génération est prise en compte. La plupart des erreurs de prédiction sont imputables à la présence de contacts cristallins. Depuis, EADock a été utilisé pour comprendre les mécanismes moléculaires impliqués dans la régulation de la Na,K ATPase et dans l'activation du peroxisome proliferatoractivated receptor a (PPARa). Il a également permis de décrire l'interaction de polluants couramment rencontrés sur PPARy, ainsi que l'influence de la métabolisation de l'Imatinib (PA anticancéreux) sur la fixation à la kinase Bcr-Abl. Une approche basée sur la prédiction des interactions de fragments moléculaires avec protéine cible est également proposée. Elle a permis la découverte de nouveaux ligands peptidiques de PPARa et de l'intégrine a5ß1. Dans les deux cas, l'activité de ces nouveaux peptides est comparable à celles de ligands bien établis, comme le Wy14,643 pour le premier, et le Cilengitide (PA anticancéreux) pour la seconde.

Rationale and design of a randomized, double-blind, parallel-group study of terutroban 30 mg/day versus aspirin 100 mg/day in stroke patients: the prevention of cerebrovascular and cardiovascular events of ischemic origin with terutroban in patients with a history of ischemic stroke or transient ischemic attack (PERFORM) study.

BACKGROUND: Ischemic stroke is the leading cause of mortality worldwide and a major contributor to neurological disability and dementia. Terutroban is a specific TP receptor antagonist with antithrombotic, antivasoconstrictive, and antiatherosclerotic properties, which may be of interest for the secondary prevention of ischemic stroke. This article describes the rationale and design of the Prevention of cerebrovascular and cardiovascular Events of ischemic origin with teRutroban in patients with a history oF ischemic strOke or tRansient ischeMic Attack (PERFORM) Study, which aims to demonstrate the superiority of the efficacy of terutroban versus aspirin in secondary prevention of cerebrovascular and cardiovascular events. METHODS AND RESULTS: The PERFORM Study is a multicenter, randomized, double-blind, parallel-group study being carried out in 802 centers in 46 countries. The study population includes patients aged > or =55 years, having suffered an ischemic stroke (< or =3 months) or a transient ischemic attack (< or =8 days). Participants are randomly allocated to terutroban (30 mg/day) or aspirin (100 mg/day). The primary efficacy endpoint is a composite of ischemic stroke (fatal or nonfatal), myocardial infarction (fatal or nonfatal), or other vascular death (excluding hemorrhagic death of any origin). Safety is being evaluated by assessing hemorrhagic events. Follow-up is expected to last for 2-4 years. Assuming a relative risk reduction of 13%, the expected number of primary events is 2,340. To obtain statistical power of 90%, this requires inclusion of at least 18,000 patients in this event-driven trial. The first patient was randomized in February 2006. CONCLUSIONS: The PERFORM Study will explore the benefits and safety of terutroban in secondary cardiovascular prevention after a cerebral ischemic event.

Needs assessment and design of the intervention for high risk sex offenders social reintegration

Executive report of the adaptation study "Needs assessment and design of the intervention for high risk sex offenders social reintegration: Adaptation of the Circles of Support and Accountability to the Penal Enforcement System of Catalonia".

Design of new tools to improve the efficacy of DNA-damaging drugs used in cancer therapy

Résumé Les tumeurs sont diverses et hétérogènes, mais toutes partagent la capacité de proliférer sans contrôle. Une prolifération dérégulée de cellules couplée à une insensibilité à une réponse apoptotique constitue une condition minimale pour que l'évolution d'une tumeur se produise. Un des traitements les plus utilisés pour traité le cancer à l'heure actuelle sont les chimiothérapies, qui sont fréquemment des composés chimiques qui induisent des dommages dans l'ADN. Les agents anticancéreux sont efficaces seulement quand les cellules tumorales sont plus aisément tuées que le tissu normal environnant. L'efficacité de ces agents est en partie déterminée par leur capacité à induire l'apoptose. Nous avons récemment démontré que la protéine RasGAP est un substrat non conventionnel des caspases parce elle peut induire à la fois des signaux anti et pro-apoptotiques, selon l'ampleur de son clivage par les caspases. A un faible niveau d'activité des caspases, RasGAP est clivé, générant deux fragments (le fragment N et le fragment C). Le fragment N semble être un inhibiteur général de l'apoptose en aval de l'activation des caspases. À des niveaux plus élevés d'activité des caspases, la capacité du fragment N de contrecarrer l'apoptose est supprimée quand il est clivé à nouveau par les caspases. Ce dernier clivage produit deux nouveaux fragments, N 1 et N2, qui contrairement au fragment N sensibilisent efficacement des cellules cancéreuses envers des agents chimiothérapeutiques. Dans cette étude nous avons prouvé qu'un peptide, appelé par la suite TAT-RasGAP317-326, qui est dérivé du fragment N2 de RasGAP et est rendu perméable aux cellules, sensibilise spécifiquement des cellules cancéreuses à trois génotoxines différentes utilisées couramment dans des traitements anticancéreux, et cela dans des modèles in vitro et in vivo. Il est important de noté que ce peptide semble ne pas avoir d'effet sur des cellules non cancéreuses. Nous avons également commencé à caractériser les mécanismes moléculaires expliquant les fonctions de sensibilisation de TAT-RasGAP317-326. Nous avons démontré que le facteur de transcription p53 et une protéine sous son activité transcriptionelle, nommée Puma, sont indispensables pour l'activité de TAT-RasGAP317-326. Nous avons également prouvé que TAT-RasGAP317-326 exige la présence d'une protéine appelée G3BP1, une protéine se liant a RasGAP, pour potentialisé les effets d'agents anticancéreux. Les données obtenues dans cette étude montrent qu'il pourrait être possible d'augmenter l'efficacité des chimiothérapies à l'aide d'un composé capable d'augmenter la sensibilité des tumeurs aux génotoxines et ainsi pourrait permettre de traiter de manière plus efficace des patients sous traitement chimiothérapeutiques. Summary Tumors are diverse and heterogeneous, but all share the ability to proliferate without control. Deregulated cell proliferation coupled with suppressed apoptotic sensitivity constitutes a minimal requirement upon which tumor evolution occurs. One of the most commonly used treatments is chemotherapy, which frequently uses chemical compounds that induce DNA damages. Anticancer agents are effective only when tumors cells are more readily killed than the surrounding normal tissue. The efficacy of these agents is partly determined by their ability to induce apoptosis. We have recently demonstrated that the protein RasGAP is an unconventional caspase substrate because it can induce both anti- and pro-apoptotic signals, depending on the extent of its cleavage by caspases. At low levels of caspase activity, RasGAP is cleaved, generating an N-terminal fragment (fragment N) and a C-terminal fragment (fragment C). Fragment N appears to be a general Mocker of apoptosis downstream of caspase activation. At higher levels of caspase activity, the ability of fragment N to counteract apoptosis is suppressed when it is further cleaved. This latter cleavage event generates two fragments, N1 and N2, which in contrast to fragment N potently sensitizes cancer cells toward DNA-damaging agents induced apoptosis. In the present study we show that a cell permeable peptide derived from the N2 fragment of RasGAP, thereafter called TAT-RasGAP317-326, specifically sensitizes cancer cells to three different genotoxins commonly used in chemotherapy in vitro and in vivo models. Importantly this peptide seems not to have any effect on non cancer cells. We have also started to characterize the molecular mechanisms underlying the sensitizing functions of TAT-RasGAP317-326. We have demonstrated that the p53 transcription factor and a protein under its transcriptional activity, called Puma, are required for the activity of TATRasGAP317-326. We have also showed that TAT-RasGAP317-326 requires the presence of a protein called G3BP1, which have been shown to interact with RasGAP, to increase the effect of the DNA-damaging drug cisplatin. The data obtained in this study showed that it is possible to increase the efficacy of current used chemotherapies with a compound able to increase the efficacy of genotoxins which could be beneficial for patients subjected to chemotherapy.

Joint physical-MAC layer design of the broadcast channel protocol in adhoc networks

Broadcast transmission mode in ad hoc networks is critical to manage multihop routing or providing medium accesscontrol (MAC)-layer fairness. In this paper, it is shown that ahigher capacity to exchange information among neighbors may beobtained through a physical-MAC cross-layer design of the broadcastprotocol exploiting signal separation principles. Coherentdetection and separation of contending nodes is possible throughtraining sequences which are selected at random from a reducedset. Guidelines for the design of this set are derived for a lowimpact on the network performance and the receiver complexity.

Handbook for the design of intercultural policies: summary of the original Spanish version

Local governments need minimum common criteria to manage the social dynamics of diversity. This Handbook defends the strategy of interculturality as a public political approach, based on a way to interpret interculturality as a positive resource, as a public cultural and a collective good. It is an approach that promotes the equitative interaction as a way to generate a cohesive common public space. This Handbook provides the reader with the conceptual and practical instruments to help (and inspire) those territories which would like to integrate interculturality as an urban project.It aims to serve as a ground for discussion to jointly work in local administrations and other government levels, fororganizations and institutions, as well as for cultural, political and citizens collectives. Results are presented asan action by the Red de Ciudades Interculturales (RECI), within the Intercultural Cities framework by the Councilof Europe, with the collaboration of Obra Social "La Caixa".

Design of adjustable packaging line

Diplomityön tavoite oli tutkia, mitä toimintoja ja tekniikoita uusi, joustava kartonkipakkauslinja sisältää ja mitkä suuntaukset pakkausteollisuudessa tulevat olemaan tärkeitä tulevaisuudessa. Pakkauslinjan päätoimintoja tarkasteltiin nykyisten jatulevaisuuden tekniikoiden pohjalta. Erityisesti tarkasteltiin laser-sovellusten käytön mahdollisuutta pakkauslinjan eri osatoiminnoissa. Katsaus pakkausteollisuuden tulevaisuuden näkymiin luotiin kirjallisuuden ja aikaisempien tutkimusten pohjalta, minkä perusteella työssä oletetaan, että yksilölliset ja monitoimipakkaukset tulevat lisääntymään tulevaisuudessa. Eri tuotantoerien välillä olevat asetusajat tulee saada minimoitua, mutta millä keinoin joustavuus on saavutettavissa? Yksi ratkaisu pakkausten valmistamisessa on käyttää robottisolua, mikä on mahdollista luultavasti ainakin kuppimuotoisten pakkausten kohdalla. Muutenkin robotiikka on lisääntymässä pakkausteollisuudessa. Digitaalisten painotekniikoiden kehitys on mahdollistanut yksilölliset painatukset. Tulevaisuudessa painatus on mahdollista tehdä pakkauslinjan loppupäässä, jopa vasta täytön ja suljennan jälkeen. Laserleikkaus on jo nyt käytössä, mutta tulevaisuudessa myös saumaus ja perinteinen nuuttaus on mahdollista tehdä lasersovelluksia käyttäen. Kehittynyt, väyläpohjainen ohjausjärjestelmä on tulevaisuudessa välttämätön joustavassa pakkauslinjassa. Internetin välityksellä toimiva etäohjattu virheenkorjausdiagnostiikka tulee myös olemaan itsestäänselvyys tulevaisuudessa. Kustannussäästöjä voidaan saavuttaa käyttämälläpakkauslinjassa modulaarista rakennetta. Standardiosien ja standardiosajärjestelmien käyttäminen pienentää myös käyttö- ja huoltokustannuksia. Tärkeää on kuitenkin muistaa, ettei joustavuutta voida saavuttaa pelkästään yhtä ominaisuutta tai tekniikkaa hyödyntäen vaan monia menetelmiä yhdistäen. Suunniteltavan pakkauslinjan toiminta on myös hyvä varmistaa käyttäen apuna mallinnusta ja simulointia.

Design of an Embedded Computer Board for Networking Applications

Tämä diplomityö tehtiin Convergens Oy:lle. Convergens on elektroniikan suunnittelutoimisto, joka on erikoistunut sulautettuihin järjestelmiin sekä tietoliikennetekniikkaan. Diplomityön tavoitteena oli suunnitella tietokonekortti tietoliikennesovelluksia varten asiakkaalle, jolta vaatimusmäärittelyt tulivat. Työ on rajattu koskemaan laitteen prototyypin suunnittelua. Työssä suunnitellaan pääasiassa WLAN-tukiaseman tietokone. Tukiasema onasennettavissa toimistoihin, varastoihin, kauppoihin sekä myös liikkuvaan ajoneuvoon. Suunnittelussa on otettu nämä asiat huomioon, ja laitteen akun pystyy lataamaan muun muassa auton akulla. Langattomat tekniikat ovat voimakkaasti yleistymässä, ja tämän työn tukiasema tarjoaakin varteenotettavan vaihtoehdon lukuisilla ominaisuuksillaan. Mukana on mm. GPS, Bluetooth sekä Ethernet-valmius. Langattomien tekniikoiden lisäksi myös sulautetut järjestelmät ovat voimakkaasti yleistymässä, ja nykyään mikroprosessoreita löytääkin lähesmistä vain. Tässä projektissa käytetty prosessori on nopeutensa puolesta kilpailukykyinen, ja siitä löytyy useita eri rajapintoja. Jatkossa tietokonekortille on myös tulossa WiMAX-tuki, joka lisää tukiaseman tulevaisuuden arvoa asiakkaalle. Projektiin valittu Freescalen MPC8321E-prosessori on PowerPC-arkkitehtuuriin perustuva ja juuri markkinoille ilmestynyt. Tämä toi mukanaan lisähaasteen, sillä kyseisestä prosessorista ei ollut vielä kaikkea tietoa saatavilla. Mekaniikka toi omat haasteensa mukanaan, sillä se rajoitti piirilevyn koonniin, että ylimääräistä piirilevytilaa ei juurikaan jäänyt. Tämän takia esimerkiksi DDR-muistit olivat haastavia reitittää, sillä muistivetojen on oltava melko samanpituisia keskenään. Käyttöjärjestelmänä projektissa käytetään Linuxia. Suunnittelu alkoi keväällä 2007 ja toimiva prototyyppi oli valmis alkusyksystä. Prototyypin testaus osoitti, että tietokonekortti kykenee täyttämään kaikki asiakkaan vaatimukset. Prototyypin testauksessa löytyneet viat ja optimoinnit on tarkoitus korjata tuotantomalliin, joten se antaa hyvän pohjan jatkosuunnittelua varten.

Customization, transparency and proximity: a user- centered content strategy applied to the design of a virtual library website

We present a case study of the redesign of the organizational presentation and content of the Virtual Library website at the Universitat Oberta de Catalunya (Open University of Catalonia, UOC), based on a user-centered design strategy. The aim of the redesign was to provide users with more intuitive, usable and understandable content (textual content, resources and services) by implementing criteria of customization, transparency and proximity. The study also presents a selection of best practices for applying these criteria to the design of other library websites.