Synthesis of CaCu3Ti4O12 ceramic via a sol-gel method

The novel nano-ultrafine powders for the preparation of CaCu3Ti4O12 ceramic were prepared by the sol-gel method and citrate auto-ignition method. The obtained precursor powders were pressed, sintered at 1000 degrees C to fabricate microcrystal CaCu3Ti4O12 ceramic. The microcrystalline phase of CaCu3Ti4O12 was confirmed by X-ray powder diffraction (XRD). The morphology and size of the grains of the powders and ceramics under different heat treatments were observed using scanning electron microscopy (SEM). The relative dielectric constant of the ceramic sintered at 1000 degrees C was measured with a magnitude of more than 10(4) at room temperature, which was approaching to those of Pb-containing complex perovskite ceramics, and the loss tangent was less than 0.20 in a broad frequency region. The relative dielectric constant and loss tangent were also compared with that of CaCu3Ti4O12 ceramic prepared by other reported methods. (c) 2006 Elsevier B.V. All rights reserved.

Investigation of the spectroscopic properties of Yb3+-doped yttrium lanthanum oxide transparent ceramic

Spectroscopic properties of (Y0.9-xLa0.1Ybx)(2)O-3 transparent ceramic were studied. Two main absorption peaks of the specimen are centered at 940 and 970 nm, which are suitable for InGaAs laser diode pumping. The main emission peaks were located at 1032 and 1075 nm with larger emission cross-section and longer fluorescence lifetime than those of Yb:Y2O3. These properties of (Y0.9-xLa0.1Ybx)(2)O-3 transparent ceramic are favorable to achieve high efficiency and high power laser output. (c) 2007 Elsevier B.V. All rights reserved.

Cooperative up-conversion luminescence of ytterbium doped yttrium lanthanum oxide transparent ceramic

The up-conversion luminescence of Yb3+-doped yttriurn lanthanum oxide transparent ceramic was investigated. It was ascribed to cooperative luminescence originated from the coupled states of the Yb3+ ion pairs. The proper doping of La2O3 can remove the cooperative luminescence of Yb3+ ion. But excessive La2O3 (at least 10 at.%) the cooperative up-conversion of Yb3+:Y2O3 is obtained again, and the intensity of up-conversion luminescence strengthens with the increase of La2O3 content. (c) 2007 Elsevier B.V. All rights reserved.

Species compositions of elasmobranchs caught by three different commercial fishing methods off southwestern Australia, and biological data for four abundant bycatch species

Commercial catches taken in southwestern Australian waters by trawl fisheries targeting prawns and scallops and from gillnet and longline fisheries targeting sharks were sampled at different times of the year between 2002 and 2008. This sampling yielded 33 elasmobranch species representing 17 families. Multivariate statistics elucidated the ways in which the species compositions of elasmobranchs differed among fishing methods and provided benchmark data for detecting changes in the elasmobranch fauna in the future. Virtually all elasmobranchs caught by trawling, which consisted predominantly of rays, were discarded as bycatch, as were approximately a quarter of the elasmobranchs caught by both gillnetting and longlining. The maximum lengths and the lengths at maturity of four abundant bycatch species, Heterodontus portusjacksoni, Aptychotrema vincentiana, Squatina australis, and Myliobatis australis, were greater for females than males. The L50 determined for the males of these species at maturity by using full clasper calcification as the criterion of maturity did not differ significantly from the corresponding L50 derived by using gonadal data as the criterion for maturity. The proportions of the individuals of these species with lengths less than those at which 50% reach maturity were far greater in trawl samples than in gillnet and longline samples. This result was due to differences in gear selectivity and to trawling being undertaken in shallow inshore waters that act as nursery areas for these species. Sound quantitative data on the species compositions of elasmobranchs caught by commercial fisheries and the biological characteristics of the main elasmobranch bycatch species are crucial for developing strategies for conserving these important species and thus the marine ecosystems of which they are part.

Comportamento mecânico de cerâmica produzida a partir de reciclagem de para-brisa de automóvel

É crescente o interesse nos materiais cerâmicos, devido as suas características como baixa massa específica e maior resistência a ambientes agressivos do que a maioria das ligas metálicas. Este trabalho tem o objetivo de produzir a partir de material descartado, cerâmicas em diferentes temperaturas de sinterização e avaliar a sua tensão de ruptura em ensaio de flexão de três pontos e a confiança desta medida. Devido ao custo de produzir pó de vidro, tanto pelo alto gasto de energia para fundir a matéria-prima como pelo consumo de minerais industriais, foi proposto utilizar vidro de para-brisa obsoleto reduzindo despesas operacionais e definindo um destino econômico e ambiental viável para estes rejeitos. A metodologia consistiu-se na obtenção do pó de vidro com características adequadas para ser conformado e sinterizado. Foram usadas duas composições e quatro tratamentos térmicos para obter oito materiais. Uma composição com apenas o pó oriundo da moagem de para-brisa e outra com este pó mais 4% de óxido de nióbio. A resistência à flexão dos produtos obtidos foi avaliada. Utilizou-se a estatística de Weibull para caracterizar estes resultados. Os resultados obtidos indicam que o material de composição pó de vidro e temperatura final de sinterização de 650C obteve a maior resistência mecânica entre os materiais sintetizados. A adição do óxido de nióbio provoca um decréscimo na resistência mecânica se comparada com o material sem a adição deste óxido. Entretanto, comparando as duas composições na mesma temperatura final de sinterização, a adição de óxido de nióbio provocou um aumento no módulo de Weibull, excetuando-se dois de oito materiais obtidos. As diferentes composições e temperaturas de sinterização afetaram as propriedades mecânicas dos materiais obtidos.

Characterisation of impact response of metallic foam/ceramic laminates

The impact response of laminated composites consisting of alternate layers of AI ahoy foam and Al2O3 was studied experimentally in low and intermediate velocity regimes. Low velocity impacts (1.2-2.8 m s(-1)) were conducted using an instrumented falling weight apparatus and were compared with static indentation tests (0.2 x 10(-4) m s(-1)). Intermediate velocity impacts were carried out by means of both Hopkinson bar (60 m s(-1)) and gas gun (200 m s(-1)) tests, Post-impact damage was assessed using X-ray radiography and microscopy, It was found that there is good correlation between low velocity impact and quasi-static responses. In both cases, penetration of the layered targets resulted in the formation of a distinctive plug. Increasing impact velocity (intermediate velocity range) snitched the penetration mode from plugging to fragmentation, giving rise to an increase in the absorbed energy. In this range, impacts led to localisation of damage in the region under the projectile, Furthermore, a comparison has been made between the penetration response of foam laminates and dense metal laminates of equivalent areal density. Preliminary results suggest that the dense metal laminates are superseded by the foam laminates on an energy absorption basis.