Effect of silica coating on flexural strength of fiber posts

Purpose: Fiber-reinforced composite (FRC) posts can be air-abraded to obtain good attachment to the resin cement. This study tested the effect of silica coating on the flexural strength of carbon, opaque, and translucent quartz FRC posts. Materials and Methods: Six experimental groups of FRC posts (n = 10 per group) were tested, either as received from the manufacturer or after chairside silica coating (30-μm CoJet-Sand). Results: There was no significant difference in the flexural strength of nonconditioned (504 to 525 MPa) and silica-coated (514 to 565 MPa) specimens (P > .05) (analysis of variance). The type of post did have a significant effect on flexural strength (P < .05). Conclusion: Chairside silica coating did not affect the flexural strength of both carbon and quartz FRC posts.

Microtensile bond strength of a resin cement to glass infiltrated zirconia-reinforced ceramic: The effect of surface conditioning

This study evaluated the effect of three surface conditioning methods on the microtensile bond strength of resin cement to a glass-infiltrated zirconia-reinforced alumina-based core ceramic. Thirty blocks (5×5×4 mm) of In-Ceram Zirconia ceramics (In-Ceram Zirconia-INC-ZR, VITA) were fabricated according to the manufacturer's instructions and duplicated in resin composite. The specimens were polished and assigned to one of the following three treatment conditions (n=10): (1) Airborne particle abrasion with 110 μm Al2O3 particles + silanization, (2) Silica coating with 110 μm SiOx particles (Rocatec Pre and Plus, 3M ESPE) + silanization, (3) Silica coating with 30 μm SiOx particles (CoJet, 3M ESPE) + silanization. The ceramic-composite blocks were cemented with the resin cement (Panavia F) and stored at 37 °C in distilled water for 7 days prior to bond tests. The blocks were cut under coolant water to produce bar specimens with a bonding area of approximately 0.6 mm2. The bond strength tests were performed in a universal testing machine (cross-head speed: 1 mm/min). The mean bond strengths of the specimens of each block were statistically analyzed using ANOVA and Tukey's test (α≤0.05). Silica coating with silanization either using 110 μm SiOx or 30 μm SiOx particles increased the bond strength of the resin cement (24.6±2.7 MPa and 26.7±2.4 MPa, respectively) to the zirconia-based ceramic significantly compared to that of airborne particle abrasion with 110-μm Al2O3 (20.5±3.8 MPa) (ANOVA, P<0.05). Conditioning the INC-ZR ceramic surfaces with silica coating and silanization using either chairside or laboratory devices provided higher bond strengths of the resin cement than with airborne particle abrasion using 110 μm Al2O3. © 2005 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Microtensile bond strength between a quartz fiber post and a resin cement: Effect of post surface conditioning

Purpose: To test the bond strength between a quartz-fiber-reinforced composite post (FRC) and a resin cement. The null hypothesis was that the bond strength can be increased by using a chairside tribochemical silica-coating system. Materials and Methods: Thirty quartz-FRCs (Light-Post) were divided into 3 groups according to the post surface treatment: G1) Conditioning with 32% phosphoric acid (1 min), applying a silane coupling agent; G2) etching with 10% hydrofluoric acid (1 min), silane application; G3) chairside tribochemical silica coating method (CoJet System): air abrasion with 30-μ SiO x-modified Al2O3 particles, silane application. Thereafter, the posts were cemented into a cylinder (5 mm diameter, 15 mm height) with a resin cement (Duo-Link). After cementation, the specimens were stored in distilled water (37°C/24 h) and sectioned along the x and y axes with a diamond wheel under cooling (Lab-cut 1010) to create nontrimmed bar specimens. Each specimen was attached with cyanoacrylate to an apparatus adapted for the microtensile test. Microtensile testing was conducted on a universal testing machine (1 mm/min). The data obtained were submitted to the one-way ANOVA and Tukey test (α = 0.05). Results: A significant influence of the conditioning methods was observed (p < 0.0001). The bond strength of G3 (15.14 ± 3.3) was significantly higher than the bond strengths of G1 (6.9 ± 2.3) and G2 (12.60 ± 2.8) (p = 0.000106 and p = 0.002631, respectively). Notwithstanding the groups, all the tested specimens showed adhesive failure between the resin cement and FRC. Conclusion: The chairside tribochemical system yielded the highest bond strength between resin cement and quartz-fiber post. The null hypothesis was accepted (p < 0.0001).

Bond strength of a resin cement to high-alumina and zirconia-reinforced ceramics: The effect of surface conditioning

Purpose: The aim of this study was to evaluate the effect of two surface conditioning methods on the microtensile bond strength of a resin cement to three high-strength core ceramics: high alumina-based (In-Ceram Alumina, Procera AllCeram) and zirconia-reinforced alumina-based (In-Ceram Zirconia) ceramics. Materials and Methods: Ten blocks (5 ×6 × 8 mm) of In-Ceram Alumina (AL), In-Ceram Zirconia (ZR), and Procera (PR) ceramics were fabricated according to each manufacturer's instructions and duplicated in composite. The specimens were assigned to one of the two following treatment conditions: (1) airborne particle abrasion with 110-μm Al2O3 particles + silanization, (2) silica coating with 30 μm SiOx particles (CoJet, 3M ESPE) + silanization. Each ceramic block was duplicated in composite resin (W3D-Master, Wilcos, Petrópolis, RJ, Brazil) using a mold made out of silicon impression material. Composite resin layers were incrementally condensed into the mold to fill up the mold and each layer was light polymerized for 40 s. The composite blocks were bonded to the surface-conditioned ceramic blocks using a resin cement system (Panavia F, Kuraray, Okayama, Japan). One composite resin block was fabricated for each ceramic block. The ceramic-composite was stored at 37°C in distilled water for 7 days prior to bond tests. The blocks were cut under water cooling to produce bar specimens (n = 30) with a bonding area of approximately 0.6 mm2. The bond strength tests were performed in a universal testing machine (crosshead speed: 1 mm/min). Bond strength values were statistically analyzed using two-way ANOVA and Tukey's test (≤ 0.05). Results: Silica coating with silanization increased the bond strength significantly for all three high-strength ceramics (18.5 to 31.2 MPa) compared to that of airborne particle abrasion with 110-μm Al2O3 (12.7-17.3 MPa) (ANOVA, p < 0.05). PR exhibited the lowest bond strengths after both Al2O3 and silica coating (12.7 and 18.5 MPa, respectively). Conclusion: Conditioning the high-strength ceramic surfaces with silica coating and silanization provided higher bond strengths of the resin cement than with airborne particle abrasion with 110-μm Al2O3 and silanization.

Resin microtensile bond strength to feldspathic ceramic: Hydrofluoric acid etching vs tribochemical silica coating

This study aimed to compare the microtensile bond strength of resin cement to alumina-reinforced feldspathic ceramic submitted to acid etching or chairside tribochemical silica coating. Ten blocks of Vitadur-α were randomly divided into 2 groups according to conditioning method: (1) etching with 9.6% hydrofluoric acid or (2) chairside tribochemical silica coating. Each ceramic block was luted to the corresponding resin composite block with the resin cement (Panavia F). Next, bar specimens were produced for microtensile testing. No significant difference was observed between the 2 experimental groups (Student t test, P> .05). Both surface treatments showed similar microtensile bond strength values.

Surface conditioning of a composite used for inlay/onlay restorations: Effect on μTBS to resin cement

Purpose: To assess the effect of the composite surface conditioning on the microtensile bond strength of a resin cement to a composite used for inlay/onlay restorations. Materials and Methods: Forty-two blocks (6 × 6 × 4 mm) of a microfilled composite (Vita VMLC) were produced and divided into 3 groups (N = 14) by composite surface conditioning methods: Gr1 - etching with 37% phosphoric acid, washing, drying, silanization; Gr2 - air abrasion with 50-l̀m Al2O3 particles, silanization; Gr3 - chairside tribochemical silica coating (CoJet System), silanization. Single-Bond (one-step adhesive) was applied on the conditioned surfaces and the two resin blocks treated with the same method were cemented using RelyX ARC (dual-curing resin cement). The specimens were stored for 7 days in water at 37°C and then sectioned to produce nontrimmed beam samples, which were submitted to microtensile bond strength testing (μTBS). For statistical analysis (one-way ANOVA and Tukey's test, · = 0.05), the means of the beam samples from each luted specimen were calculated (n = 7). Results: μTBS values (MPa) of Gr2 (62.0 ± 3.9a) and Gr3 (60.5 ± 7.9a) were statistically similar to each other and higher than Gr1 (38.2 ± 8.9b). The analysis of the fractured surfaces revealed that all failures occurred at the adhesive zone. Conclusion: Conditioning methods with 50-l̀m Al2O3 or tribochemical silica coating allowed bonding between resin and composite that was statistically similar and stronger than conditioning with acid etching.

The influence of the mixing time in the rheological behavior of cement pastes

Rheology has the purpose to study the flux and deformation of materials when submitted to some tension or outer mechanical solicitation. In practice, the effective scientific field broached by rheology is restricted only to the study of homogeneous fluids behavior, in which are included eminent liquids, particles suspensions, and emulsions. The viscosity (η) and the yield stress (τ 0) are the two basic values that define the fluids' behavior. The first one is the proportionality constant that relates the shear rate (γ) with the shear stress (τ) applied, while the second indicates the minimal tension for the flowage beginning. The fluids that obey the Newton's relation - Newtonians fluids - display the constant viscosity and the null yield stress. It's the case of diluted suspensions and grate amount of the pure liquids (water, acetone, alcohol, etc.) in which the viscosity is an intrinsic characteristic that depends on temperature and, in a less significant way, pressure. The suspension, titled Cement Paste, is defined as being a mixture of water and cement with, or without, a superplasticizer additive. The cement paste has a non-Newtonian fluid behavior (pseudoplastic), showing a viscosity that varies in accord to the applied shear stress and significant deformations are obtained from a delimited yield stress. In some cases, systems can also manifest the influence of chemical additives used to modify the interactions fluid/particles, besides the introduced modifications by the presence of incorporated air. To the cement paste the rheometric rehearsals were made using the rheometer R/S Brookfield that controls shear stress and shear rate in accord to the rheological model of Herschel-Bulkley that seems to better adapt to this kind of suspension's behavior. This paper shows the results of rheometrical rehearsals on the cement paste that were produced with cements HOLCIM MC-20 RS and CPV-ARI RS with the addition of superplasticizer additives based of napthaline and polycarboxilate, with and without a constant agitation of the mixture. The obtainment of dosages of superplasticizer additives, as well as the water/cement ratio, at the cement at the fluidify rate determination, was done in a total of 12 different mixtures. It's observed that the rheological parameters seem to vary according to the cement type, the superplasticizer type, and the methodology applied at the fluidity rate determination.

Effect of surface treatments on the bond strength of a resin cement to commercially pure titanium

Investigation of the effectiveness of surface treatments that promote a strong bond strength of resin cements to metals can contribute significantly to the longevity of metal-ceramic restorations. This study evaluated the effect of surface treatments on the shear bond strength (SBS) of a resin cement to commercially pure titanium (CP Ti). Ninety cast CP Ti discs were divided into 3 groups (n=30), which received one of the following airborne-particle abrasion conditions: (1) 50 μm Al2O3 particles; (2) 30 μm silica-modified Al2O3 particles (Cojet Sand); (3) 110 μm silica-modified Al2O3 particles (Rocatec). For each airborne-particle abrasion condition, the following post-airborne-particle abrasion treatments were used (n=10): (1) none; (2) adhesive Adper Single Bond 2; (3) silane RelyX Ceramic Primer. RelyX ARC resin cement was bonded to CP Ti surfaces. All specimens were thermally cycled before being tested in shear mode. Failure mode was determined. The best association was Rocatec plus silane. All groups showed 100% adhesive failure. There were combinations that promote higher SBS than the protocol recommended by the manufacturer of RelyX ARC.

Bonding all-ceramic restorations with two resins cement techniques: A clinical report of three-year follow-up

Ceramics have been widely used for esthetic and functional improvements. The resin cement is the material of choice for bonding ceramics to dental substrate and it can also dictate the final esthetic appearance and strength of the restoration. The correct use of the wide spectrum of resin luting agents available depends on the dental tooth substrate. This article presents three-year clinical results of a 41 years old female patient B.H.C complaining about her unattractive smile. Two all-ceramic crowns and two laminates veneers were placed in the maxillary incisors and cemented with a self-adhesive resin luting cement and conventional resin luting cement, respectively. After a three-year follow-up, the restorations and cement/teeth interface were clinically perfect with no chipping, fractures or discoloration. Proper use of different resin luting cements shows clinical appropriate behavior after a three-year follow-up. Self-adhesive resin luting cement may be used for cementing all-ceramic crowns with high predictability of success, mainly if there is a large dentin surface available for bonding and no enamel at the finish line. Otherwise, conventional resin luting agent should be used for achieving an adequate bonding strength to enamel.

Effect of seating forces on cement-ceramic adhesion in microtensile bond tests

Objectives: The aim of this study was to evaluate the effect of different seating forces during cementation in cement-ceramic microtensile bond strength (μTBS). Materials and methods: Forty-five blocks (5 × 5 × 4 mm3) of a glass-infiltrated alumina-based ceramic (In-Ceram Alumina) were fabricated according to the manufacturer's instructions and duplicated in resin composite. Ceramic surfaces were polished, cleaned for 10 min in an ultrasonic bath, silica coated using a laboratory type of air abrasion device, and silanized. Each treated ceramic block was then randomly assigned to five groups (n = 9) and cemented to a composite block under five seating forces (10 g, 50 g, 100 g, 500 g, and 750 g) using a dual-cured resin cement (Panavia F). The ceramic-cement-composite assemblies were cut under coolant water to obtain bar specimens (1 mm × 0. 8 mm2). The μTBS tests were performed in a universal testing machine (1 mm/min). The mean bond strengths values were statistically analyzed using one-way ANOVA (α ≤ 0. 05). Results: Different seating forces resulted in no significant difference in the μTBS results ranging between 13. 1 ± 4. 7 and 18. 8 ± 2. 1 MPa (p = 0. 13) and no significant differences among cement thickness. Conclusions: Excessive seating forces during cementation seem not to affect the μTBS results. Clinical relevance: Excessive forces during the seating of single all-ceramic restorations cementation seem to display the same tensile bond strength to the resin cement. © 2012 Springer-Verlag.

Si-based thin film coating on Y-TZP: Influence of deposition parameters on adhesion of resin cement

This study evaluated the influence of deposition parameters for Si-based thin films using magnetron sputtering for coating zirconia and subsequent adhesion of resin cement. Zirconia ceramic blocks were randomly divided into 8 groups and specimens were either ground finished and polished or conditioned using air-abrasion with alumina particles coated with silica. In the remaining groups, the polished specimens were coated with Si-based film coating with argon/oxygen magnetron discharge at 8:1 or 20:1 flux. In one group, Si-based film coating was performed on air-abraded surfaces. After application of bonding agent, resin cement was bonded. Profilometry, goniometry, Energy Dispersive X-ray Spectroscopy and Rutherford Backscattering Spectroscopy analysis were performed on the conditioned zirconia surfaces. Adhesion of resin cement to zirconia was tested using shear bond test and debonded surfaces were examined using Scanning Electron Microscopy. Si-based film coating applied on air-abraded rough zirconia surfaces increased the adhesion of the resin cement (22.78 ± 5.2 MPa) compared to those of other methods (0-14.62 MPa) (p = 0.05). Mixed type of failures were more frequent in Si film coated groups on either polished or air-abraded groups. Si-based thin films increased wettability compared to the control group but did not change the roughness, considering the parameters evaluated. Deposition parameters of Si-based thin film and after application of air-abrasion influenced the initial adhesion of resin cement to zirconia. © 2013 Elsevier B.V. All rights reserved.

Análise experimental da durabilidade de concretos de alto desempenho com adição de resíduo de borracha de pneu e cinza da casca de arroz

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Avaliação de sistemas de reparo para o problema de abrasão do concreto de superfícies úmidas em usinas hidrelétricas

A área de pesquisa em patologia das construções vem crescendo muito ultimamente, devido à degradação natural observada nos mais diversos tipos de edificações. Neste sentido, grande atenção vem sendo dispendida às estruturas de concreto de obras especiais como usinas hidrelétricas (UHEs) em virtude de sua complexidade e importância, tanto social quanto econômica. Uma das patologias que mais ocorrem nestas estruturas é a abrasão hidráulica do concreto, a qual pode levar a construção à ruína, em casos extremos. Este trabalho visa obter e analisar dados de vários materiais de reparo quanto à resistência à abrasão hidráulica e quanto aos seus respectivos sistemas de aderência. Dividiu-se a pesquisa em três grandes etapas: na primeira verificaria as características físicas e mecânicas dos materiais de reparo, a segunda analisaria a compatibilidade entre reparo e substrato através da aderência obtida no ensaio de compressão na junta diagonal e a terceira forneceria dados sobre a resistência à abrasão dos reparos através do ensaio ASTM C1138. Na primeira etapa foram realizados os ensaios de resistência à compressão axial e consistência dos concretos e argamassas utilizados como reparos profundos e superficiais para as idades de 3, 7 e 28 dias; Na segunda, aos 3 e 28 dias de idade, foram realizados os ensaios de aderência dos sistemas adesivos, abrangendo materiais cimentícios e à base de polímeros; Na última etapa foram utilizados os mesmos materiais de reparo da primeira: argamassas e concretos à base de cimento com e sem adição de pozolanas sílica ativa e metacaulim e argamassa à base de resina epóxi aos 3 e 28 dias. Como resultados, foram obtidas resistências à compressão axial entre 40 e 65 MPa para os materiais cimentícios aos 3 dias de idade e entre 60 e 80 MPa aos 28 dias, enquanto que para a argamassa epóxi a resistência foi de 20 MPa para ambas as idades. A consistência das argamassas foi tixotrópica, enquanto que a dos concretos foi bastante fluida. Quanto à aderência, realizou-se a aplicação dos adesivos em superfícies escarificadas, limpas e encharcadas, o que possibilitou uma expressiva vantagem dos adesivos à base de cimento e relação aos poliméricos, mesmo estes sendo indicados para colagem em substratos úmidos. Na etapa de abrasão dos reparos, utilizou-se uma nova metodologia de preparo dos substratos de concreto e posterior aplicação dos reparos, classificados em profundos ou superficiais. O reparo que apresentou maior resistência à abrasão foi o de argamassa epóxi. Não houve diferença estatística significativa entre os concretos sem adição e com adição de sílica ativa e metacaulim de alta reatividade. Em geral, o desgaste das argamassas, especialmente aos 3 dias, foi maior que o dos concretos, onde se verificou claramente a presença de dois estágios de taxa de desgaste em função da resistência à abrasão dos agregados graúdos. Assim, foi possível identificar diferentes estágios de desgaste para os concretos utilizados.

Opalas gemológicas do Piauí: gênese revelada por microtermometria e minerais associados

As opalas de Pedro II e Buriti dos Montes, no estado do Piauí, constituem as mais importantes ocorrências brasileiras dessa gema, tanto em termos de volume quanto pela qualidade gemológica, que é comparável à das famosas opalas australianas. No entanto, a informalidade na extração e comercialização destas opalas, assim como a falta de informações quanto à gênese destes depósitos não permitem a prospecção por novas jazidas e o estabelecimento de um certificado de procedência para as opalas do Piauí que permitisse sua inserção formal no mercado gemológico internacional. Alguns autores têm se dedicado ao estudo dessas opalas, revelando fortes evidências de sua origem hidrotermal, mas até então, nenhum trabalho abordou as características físico-químicas dos fluidos que teriam originado esses depósitos de opalas. Diante disso, o principal objetivo deste trabalho foi entender o sistema hidrotermal responsável pela gênese das opalas do Piauí, ou seja, caracterizar os fluidos que originaram a mineralização e mostrar sua relação com o contexto geológico da região. Os municípios de Pedro II e Buriti dos Montes se localizam na porção nordeste do estado do Piauí, a aproximadamente 230 km a leste da capital Teresina, e as ocorrências de opala se encontram na porção basal da Bacia do Parnaíba, constituindo veios e vênulas nos arenitos dos grupos Serra Grande (Buriti dos Montes) e Canindé (Pedro II), os quais são seccionados por soleiras e diques de diabásio da Formação Sardinha. Elas também ocorrem cimentando brechas e como depósitos coluvionares e de paleocanal. Associados às opalas, localmente encontram-se veios de quartzo, calcedônia, barita e hematita (ou goethita). De maneira geral, as opalas de Pedro II apresentam jogo de cores, são predominantemente brancas ou azuladas com aspecto leitoso, semitranslúcidas a opacas e com inclusões sólidas pouco aparentes. Em contrapartida, as opalas de Buriti dos Montes não apresentam jogo de cores, a cor varia entre amarelo claro e vermelho amarronzado, são semitransparentes a translúcidas e contêm grande variedade de inclusões sólidas. Os dados obtidos revelam que as opalas de Pedro II são tipicamente do tipo amorfo (opala-A), enquanto as opalas de Buriti dos Montes variam entre amorfas e cristobalita-tridimita (opala-CT). Na opala preciosa, o típico jogo de cores é causado pelo arranjo regular das esferas de sílica que as constituem. A ausência de cimento opalino entre as esferas reforça a beleza desse efeito. Em contrapartida, as opalas laranja não apresentam jogo de cores, mas têm maior transparência devido ao diminuto tamanho das esferas. As inclusões sólidas também produzem belos efeitos nas opalas estudadas, principalmente na variedade laranja, que é mais transparente. Além disso, o conjunto de inclusões sólidas revela características intrínsecas aos processos hidrotermais que originaram as opalas estudadas. Agregados botrioidais, dendríticos e nodulares são exemplos de inclusões formadas por fragmentos dos arenitos hospedeiros carreados pelos fluidos hidrotermais que geraram as opalas. As inclusões sólidas também têm relação direta com a cor das opalas. Nas opalas de Buriti dos Montes, os tons de vermelho, laranja e amarelo são produzidos pela dissolução parcial das inclusões constituídas por oxihidróxidos de Fe. De maneira semelhante, a cor verde nas opalas preciosas está relacionada aos microcristais de Co-pentlandita inclusos nas mesmas. O conjunto de minerais associados às opalas conduz a uma assinatura mineralógicogeoquímica marcada pelos elevados teores de Fe e Al nas opalas com inclusões de hematita/goethita e caulinita, e assim também com aumento considerável dos teores de elementos terras raras nas opalas em que se concentram as inclusões de caulinita e apatita. Entre os elementos-traço, Ba é o mais abundante, e provavelmente foi incorporado pelo fluido hidrotermal, tendo em vista que veios de barita são encontrados com frequência nessa região da Bacia do Parnaíba. Várias feições como estruturas de fluxo nas opalas, corrosão e dissolução parcial dos cristais de quartzo hialino e de inclusões mineralógicas, vênulas de quartzo hidrotermal sobrecrescidas aos grãos detríticos, e zoneamento dos cristais de quartzo confirmam que essas opalas têm origem hidrotermal. A ruptura do Gondwana teria provocado um vasto magmatismo básico fissural, que por sua vez foi responsável pelo aporte de calor que gerou as primeiras células convectivas de fluidos quentes. A água contida nos arenitos certamente alimentou o sistema e se enriqueceu em sílica através da dissolução parcial ou total dos próprios grãos de quartzo dos arenitos. Este fluido hidrotermal foi posteriormente aprisionado em sistemas de fraturas e nelas se resfriou, precipitando a opala e minerais associados.

Paleoambiente e diagênese da formação Itaituba, carbonífero da bacia do Amazonas, com base em testemunho de sondagem, região de Uruará, Pará

A Formação Itaituba de idade carbonífera representa a sedimentação carbonática de depósitos transgressivos do Grupo Tapajós da Bacia do Amazonas. A sucessão Itaituba é interpretada como depósitos de planície de maré mista, constituídos de calcários fossilíferos, dolomitos finos, arenitos finos a grossos e subordinadamente siltitos avermelhados, evaporitos e folhelhos negros. A análise de fácies e microfácies do testemunho de sondagem da região de Uruará, Estado do Pará, permitiu individualizar dezenove fácies agrupadas em cinco associações: planície de maré (AF1), canal de maré (AF2), laguna (AF3), barra bioclástica (AF4) e plataforma externa (AF5). AF1 é composta por arenito fino com rip-up clasts e gretas de contração, marga com grãos de quartzo e feldspato, dolomudstone laminado com grãos terrígenos e dolomito fino silicificado, com intercalação de argilito com grãos de quartzo disseminados, dolomitizado e localmente com sílica microcristalina. AF2 consiste em arenito médio a grosso com estratificação cruzada acanalada, recoberta por filmes pelíticos nos foresets, arenito muito fino a fino com acamamento wavy, siltito laminado com falhas sinsedimentares e acamamento convoluto. AF3 é constituída de siltito vermelho maciço, mudstone com fósseis, floatstone com braquiópodes e pirita disseminada e mudstone maciço com frequentes grãos de quartzo. AF4 e AF5 exibem abundantes bioclastos representados por espinhos e fragmentos de equinodermas, conchas, fragmentos e espinhos de braquiópodes, ostracodes, foraminíferos, algas vermelhas e conchas de bivalves. AF4 é formada por grainstone oolítico fossilífero e grainstone com terrígenos principalmente grãos de quartzo monocristalino e AF5 se compõe de wackestone fossilífero, wackestone com terrígenos e mudstone maciço com grãos de quartzo monocristalino. Subarcósios (AF1), arcósios (AF2) e arcósios líticos (AF2) são os tipos de arenitos da sucessão Itaituba e apresentam como principais constituintes grãos de quartzo monocristalino e policristalino, K-feldspato, plagioclásio, pirita, muscovita detrítica, fragmento de rocha pelítica, metamórfica e chert e raros bioclastos. O cimento é de calcita espática não ferrosa, óxido/hidróxido de ferro e sobrecrescimento de sílica. A porosidade é intergranular, móldica e às vezes alongada, sem permeabilidade perfazendo até 11% da rocha. Os processos diagenéticos dos arenitos são compactação física, sobrecrescimento de sílica, cimentação de calcita, formação de matriz diagenética, compactação química, substituição de grãos, autigênese de pirita, formação de óxido/hidróxido de ferro e alteração do plagioclásio. Os processos diagenéticos dos carbonatos são: micritização, neomorfismo, colomitização, fraturamento, compactação química, cimentação de calcita, dissolução secundária e autigênese de minerais. A sucessão da Formação Itaituba representa um sistema de laguna/planície de maré ligada a uma plataforma marinha carbonática. Planícies de maré desenvolveram-se nas margens das lagunas e eram periodicamente supridas por influxos de terrígenos finos (silte) que inibiam a precipitação carbonática. Barras bioclásticas eram cortadas por canais de maré (inlet) que conectavam a laguna com a plataforma rasa rica em organismos bentônicos.