Evaluation of stitched fabric composite processed by RTM in quasi-static test

Stitched fabrics have been widely studied for potential application in aircraft structures since stitch yarns offer improvements in the out-of-plane mechanical properties and also can save time in the lay up process. The down side of stitch yarns came up in the manufacturing process of fabric in which defects introduced by the needle movement creating fiber-free-zones, fiber breakage and misalignment of fibers. The dry stitched carbon fabric preform has mainly been used in the Resin Transfer Molding (RTM) process which high fiber content is aimed, those defects influence negatively the injection behavior reducing the mechanical properties of final material. The purpose of this research work focused on testing in quasi-static mechanical mode (in-plane tension) of a monocomponent resin CYCOM (R) 890 RTM/carbon fiber anti-symmetric quadriaxial fabric stitched by PE 80Dtex yarn processed by RTM. The evaluation consisted in comparing the scatter of the quasi-static test with the attenuation of ultrasonic maps, which show the path of the resin and possible dry spots considering that interference of yarn in resin flow is detectable in ultrasonic measurement. Microscopic analysis was also considered for further evaluation in case of premature failure. (C) 2011 Published by Elsevier Ltd. Selection and peer-review under responsibility of ICM11

Influence of voids on the flexural resistance of the NCF/RTM6 composites

A major difficulty to achieve maximum weight savings in the manufacture of composite structural components, is the tendency of these materials have the formation of voids and cracks in the interior and surface components. In aeronautical applications, controlling the volume fraction of fibers, resins and empty the components of composite is very hard. In this work, composites of epoxy matrix RTM6 reinforced with NCF (non crimp fabric carbon) processed by resin transfer molding (RTM) were characterized for porosity (P-ap) and density (rho(ad)). We used a method based on Archimedes' principle (ASTM C830) and the technique of helium pycnometer. The porosity values were compared with those determined by acid digestion (ASTM D3171). The mechanical properties of processed composites was evaluated by testing on the performing flexural and the results were correlated with the porosity value. All techniques tested to determine void content are satisfactory. The differents results can be justified for heterogeneous void distribution on laminate and differences among techniques characteristics. (C) 2011 Published by Elsevier Ltd. Selection and/or peer-review under responsibility of ICM11

Mechanical properties of HIPS/sugarcane bagasse fiber composites after accelerated weathering

The effect of accelerated weathering on the visual appearance and on mechanical properties of high impact polystyrene (HIPS) as well as HIPS reinforced with mercerized and bleached sugarcane bagasse fibers composites are investigated. After accelerated weathering period of 900 h, under UV-B radiation and moisture regular cycles, changes in mechanical properties are investigated by tensile tests. Materials fracture surfaces are investigated by scanning electron microscopy (SEM). The study showed that the exposure time was sufficient to change the visual appearance of HIPS as the composites. From this study, it was observed that composites reinforced with bleached fibers are less susceptible to accelerated weathering exposure than composites reinforced with mercerized fibers, which is explained by the higher amount of lignin present in mercerized fibers. (C) 2010 Published by Elsevier Ltd. Selection and peer-review under responsibility of [name organizer]

Relative growth and sexual maturity of the stone crab Menippe nodifrons Stimpson, 1859 (Brachyura, Xanthoidea) in southeastern Brazil

O objetivo do presente estudo foi determinar o crescimento relativo e a maturidade sexual morfológica de Menippe nodifrons. As coletas foram realizadas na Praia Grande e Tenório, Ubatuba, São Paulo. Os caranguejos foram separados quanto ao sexo e mensurados na região da largura (LC) e comprimento da carapaça, comprimento e altura dos própodos quelares direito e esquerdo, largura do abdome (LA) nas fêmeas e comprimento do gonopódio (CG) nos machos. Obteve-se 399 indivíduos, sendo 195 machos e 204 fêmeas. Os machos atingiram a maturidade sexual com 29,7mm LC e as fêmeas com 31,6mm LC. Para as fêmeas a melhor relação que indicou a muda da puberdade foi LA vs. LC, sendo que o crescimento foi alométrico negativo na fase jovem e alométrico positivo após a muda da puberdade. Para os machos foi CG vs. LC evidenciando crescimento alométrico positivo na fase jovem e isométrico na fase adulta.

Primeiro registro de predação de Poecilia reticulata Peters, 1859 e Phalloceros caudimaculatus (Hensel, 1868) por Noctilio leporinus (Linnaeus, 1758) (Chiroptera, Noctilionidae)

Noctilio leporinus (Chiroptera, Noctilionidae) has adaptations to piscivorous feeding habits, but also consumes crustaceans and insects. Between June 2005 and May 2006, bats were surveyed with mist nets during two evenings per month in the gallery forest of Corrego dos Tenentes, Pindorama, São Paulo State, Brazil. The objectives were to collect fecal samples and identify the fish species that were consumed by N. leporinus in this fragmented forest landscape. We documented two new fish species to its diet, the guppy Poecilia reticulata, Peters, 1859 and the "guaru" Phalloceros caudimaculatus (Hensel, 1868). Both fish species forage near the surface of water for insects and zooplankton, which is an area also utilized by N. leporinus when foraging for insects, crustaceans and fishs.

Subsistemas de comércio costeiros e internalização de interesses na dissolução do Império Colonial português (Santos, 1788-1822)

Discutem-se os primeiros resultados de uma pesquisa sobre o comércio costeiro e suas relações com o funcionamento do sistema colonial e com o contexto da Independência. A tese é de que em portos menores da costa da capitania de São Paulo, como em Santos, havia um grupo de comerciantes que atuava efetivamente no comércio costeiro e defendeu seus interesses de exclusividade de participação nesse setor contra a presença de comerciantes externos à vila. A discussão apoia-se em documentos da alfândega de Santos, como mapas de exportação-importação, mapas de embarcações, ofícios de governadores e juízes da alfândega e requerimentos de negociantes estrangeiros.

Evaluation of shot peening on the fatigue strength of anodized Ti-6Al-4V alloy

The increasingly design requirements for modern engineering applications resulted in the development of new materials with improved mechanical properties. Low density, combined with excellent weight/strength ratio as well as corrosion resistance, make the titanium attractive for application in landing gears. Fatigue control is a fundamental parameter to be considered in the development of mechanical components. The aim of this research is to analyze the fatigue behavior of anodized Ti-6Al-4V alloy and the influence of shot peening pre treatment on the experimental data. Axial fatigue tests (R = 0.1) were performed, and a significant reduction in the fatigue strength of anodized Ti-6Al-4V was observed. The shot peening superficial treatment, which objective is to create a compressive residual stress field in the surface layers, showed efficiency to increase the fatigue life of anodized material. Experimental data were represented by S-N curves. Scanning electron microscopy technique (SEM) was used to observe crack origin sites.

Coating residual stress effects on fatigue performance of 7050-T7451 aluminum alloy

The tendency of the aircraft industry is to enhance customer value by improving performance and reducing environmental impact. In view of availability, aluminum alloys have a historically tendency to faster insertion due to their lower manufacturing and operated production infrastructure. In landing gear components, wear and corrosion control of many components is accomplished by surface treatments of chrome electroplating on steel or anodizing of aluminum. One of the most interesting environmentally safer and cleaner alternatives for the replacement of hard chrome plating or anodizing is tungsten carbide thermal spray coating, applied by the high velocity oxy fuel (HVOF) process. However, it was observed that residual stresses originating from these coatings reduce the fatigue strength of a component.An effective process as shot peening treatment, considered to improve the fatigue strength, pushes the crack sources beneath the surface in most of medium and high cycle cases, due to the compressive residual stress field induced. The objective of this research is to evaluate a tungsten carbide cobalt (WC-Co) coating applied by the high velocity oxy fuel (HVOF) process, used to replace anodizing. Anodic films were grown on 7050-T7451 aluminum alloy by sulfuric acid anodizing, chromic acid anodizing and hard anodizing. The influence on axial fatigue strength of anodic films grown on the aluminum alloy surface is to degrade the stress-life performance of the base material. Three groups of specimens were prepared and tested in axial fatigue to obtain S-N curves: base material, base material coated by HVOF and base material shot peened and coated.Experimental results revealed increase in the fatigue strength of Al 7050-T7451 alloy associated with the WC 17% Co coating. on the other hand, a reduction in fatigue life occurred in the shot peened and coated condition. Scanning electron microscopy technique and optical microscopy were used to observe crack origin sites, thickness and coating/substrate adhesion. (c) 2007 Elsevier B.V. All rights reserved.

An investigation of electrolytic surface damages and electroplated crhomium effects on fatigue behavior of high strength steel

Fatigue crack initiation occurs at the surface, although sub surface nucleation has also been reported. Localized imperfections like inclusions close to surface and surface small pits can result in crack sources. Coatings are not always beneficial by fatigue point of view too. Mechanical properties of the covering material can change considerably the fatigue behavior of base metal due to residual surface stresses, to micro cracks or to hydrogen embrittlement. This paper is concerned with analysis of electrolytic etch on the fatigue resistance of a 35NCD16 high strength steel in a mechanical condition of (1760 - 1960) MPa, and analysis of electroplated hard chromium effects on the fatigue resistance in a strength condition of 989 MPa. Hardness impression was used as a reference parameter in case of electrolytic etch. In both cases, experimental data showed that fatigue strength of 35NCD16 steel was considerably reduced. Copyright © 2001 Society of Automotive Engineers, Inc.

Structural, cytochemical, immunocytochemical and ultrastructural characterization of blood granulocytes of the roadside hawk Buteo magnirostris (Gmelin, 1788) (Avian, Falconiform)

In the peripheral blood of the roadside hawk, Buteo magnirostris, the following types of granulocytic leucocytes were identified: heterophil, eosinophil and basophil. The heterophils presented acidophilic and spindle shaped granules, the eosinophils possess spherical eosinophilic granules and the basophils showed spherical and basophilic granules. The heterophils and eosinophils presented positive cytochemical reaction to glycogen and basic polyaminoacid, while the eosinophils presented sudanophilic granules, which were also positive for myeloperoxidase. The heterophils, alone, presented positivity for acid phosphatase in some granules and immunoreactivity to TGF-β1 was observed only in the cytoplasm of the eosinophils. Electron microscopy demonstrated the heterophil granules as predominantly spindle shaped, being strongly electron-dense, while the eosinophils had numerous uniformly electron-dense spherical granules and the basophils presented three different types of granules identified according to their electron-density and the aspect of their matrix.

Estudo biológico e biométrico dos estádios ninfais de Rhodnius prolixus Stäl, 1859 (Hemiptera, Reduviidae) sob condições laboratoriais

Eggs and nymphs originated from couples of Rhodnius prolixus obtained from nymphs of the 5th instar were used for biological cycle and biometric studies. The following biological cycle parameters were determined under a temperature of 28°C and relative humidity, varying between 52 - 94% : medium period of incubation: 13.01 days; rate of eggs eclosion: 77.6%; medium period of development of the 1st, 2nd, 3rd, 4 th, 5th instar nymphs : 19.33, 19.09, 20.38, 24.37, 38.14 days, respectively; percentual of deaths in the nymph instar: 26.70, 14.00, 18.26, 17.02, 35.47% respectively; percentual of changes per instar nymphs; 73.30, 86.03, 81.73, 82.97, 64.52%, respectively. Biometric measurements performed, showed that in all the instars the abdomen is the largest segment. In the four first instars, the head is larger than the thorax. In the fifth instar, the head and thorax present are about the same size.

The megalopa stage of Portunus spinimanus Latreille, 1819 and Portunus gibbesii (Stimpson, 1859) (Decapoda, Brachyura, Portunidae) from the southeastern Atlantic coast of the United States

The identification of megalopae from plankton samples is difficult, because this larval stage is the least well known among crab larvae, unknown in some species and poorly described in others. Wild megalopa specimens of some swimming crabs (family Portunidae Rafinesque, 1815) were captured alive from neuston samples obtained during summer surveys near the coast of Charleston, South Carolina (U.S.A). For identification purposes, larvae were reared to the 8th juvenile instar. After reaching the 5th juvenile instar, the juvenile crabs exhibited morphological features suitable for identification to the species level. The specimens belonged to two species of Portunidae, Portunus spinimanus Latreille, 1819 and P. gibbesii (Stimpson, 1859). Their megalopae were described in detail and compared to other portunid megalopae known from the southeastern Atlantic coast of the U.S.A. Species-specific characters of portunid megalopae are the number of carpal spines on the chelipeds, the relative size of the sternal spines (7th sternite), the number of antennal flagellum segments, and the setation of mouthparts. Copyright © 2007 Magnolia Press.

Novel cellulose/NbOPO 4.nH 2O hybrid material from sugarcane bagasse

In recent years studies concerning the applications of lignocellulosic/ inorganic couples have resulted in the development of an interesting class of functional materials. In this work a cellulose/NbOPO 4.nH 2O hybrid using cellulose from surgacane bagasse was prepared and characterized in order to test for adsorption applications. The preparation process was conducted by carrying out metallic niobium dilution in hydrofluoric acid in the presence of nitric acid, then adding boric acid to form the complex and, finally, the cellulose sugar cane bagasse was added. Concentrated phosphoric acid was also inserted to precipitate hydrous niobium phosphate particles in the cellulose fiber. This material was characterized by X-ray diffractometry (XRD), thermogravimetry (TG/DTG), and scanning electronic microscopy (SEM) connected to an energy dispersive spectrophotometer (EDS). Results by SEM/EDS show that NbOPO 4.nH 2O was present in structure of the cellulose. During the preparation of the material, using boric acid it was observed that the formation of precipitate occurred in a shorter time than the material prepared without boric acid.

Characterization of high density polyethylene (HDPE) reinforced with banana peel fibers

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of fiber surface on flexural strength in carbon fabric reinforced epoxy composites

The effect of carbon fiber surface characteristics on flexural properties of structural composites is studied in this work. Two types of intermediate modulus carbon fibers were used: T800HB and IM7. Results revealed that higher mechanical properties are linked with higher interfacial adhesion. Morphologies and chemical compositions of commercial carbon fibers (CF) were characterized by Fourier Transformed Infra Red (FTIR) and Scanning Electronic Microscopy (SEM). Comparing the results, the T800HB apparently has more roughness, since the IM7 seems to be recovered for a polymeric film. On other hand, the IM7 one shows higher interactivity with epoxy resin system Cycom 890 RTM. Composites produced with Resin Transfer Molding (RTM) were tested on a flexural trial. Interfacial adhesion difference was showed with SEM and Dynamic Mechanical Analyses (DMA), justifying the higher flexural behavior of composites made with IM7 fibers. © 2013 Elsevier B.V. All rights reserved.