The preparation of highly ordered single layer ZSM-5 coating on prefabricated stainless steel microchannels

An elegant way to prepare catalytically active microreactors is by applying a coating of zeolite crystals onto a metal microchannel structure. In this study the hydrothermal formation of ZSM-5 zeolitic coatings on AISI 316 stainless steel plates with a microchannel structure has been investigated at different synthesis mixture compositions. The procedures of coating and thermal treatment have also been optimized. Obtaining a uniform thickness of the coating within 0.5 mm wide microchannels requires a careful control of various synthesis variables. The role of these factors and the problems in the synthesis of these zeolitic coatings are discussed. In general, the synthesis is most sensitive to the H2O/Si ratio as well as to the orientation of the plates with respect to the gravity vector. Ratios of H2O/Si=130 and Si/template=13 were found to be optimal for the formation of a zeolitic film with a thickness of one crystal at a temperature of 130 degreesC and a synthesis time of about 35 h. At such conditions, ZSM-5 crystals were formed with a typical size of 1.5 mu mx1.5 mu mx1.0 mum and a very narrow (within 0.2 mum) crystal size distribution. The prepared samples proved to be active in the selective catalytic reduction (SCR) of NO with ammonia. The activity tests have been carried out in a plate-type microreactor. The microreactor shows no mass transfer limitations and a larger SCR reaction rate is observed in comparison with pelletized Ce-ZSM-5 catalysts; (C) 2001 Elsevier Science B.V. All rights reserved.

Structural and magnetic properties of Ni>1-x>Zn>x>Fe>2>O>4> (x=0, 0.5 and 1) nanopowders prepared by sol-gel method

>A series of nanostructured Ni-Zn ferrites Ni1-xZnxFe2O4 (x=0, 0.5 and 1) with a grain size from 24 to 65 nm have been prepared with a sol-gel method. The effect of composition and sintering temperature on morphology, magnetic properties, Curie temperature, specific heating rate at 295 kHz and hysteresis loss have been studied. The highest coercivity of 50 and 40 Oe, were obtained for NiFe2O4 and Ni0.5Zn0.5Fe2O4 samples with the grain size of 35 and 29 nm, respectively. The coercivity of Ni and Ni-Zn mixed ferrites decreased with temperature. The Bloch exponent was 1.5 for all samples. As the grain size increased, the Curie temperature of NiFe2O4 increased from 849 to 859 K. The highest saturation magnetization of 70 emu/g at 298 K and the highest specific heating rate of 1.6 K/s under radiofrequency heating at 295 kHz were observed over NiFe2O4 calcined at 1073 K. Both the magnitude of the hysteresis loss and the temperature dependence of the loss are influenced by the sintering temperature and composition.>

Influence of water flow rate on shear bond strength of resin composite to Er : YAG cavity preparation

Purpose: To evaluate in vitro the influence of water flow rate on shear bond strength of a resin composite to enamel and dentin after Er:YAG cavity preparation. Methods: Ten bovine incisors were selected and roots removed. Crowns were sectioned in four pieces, resulting in 40 samples that were individually embedded in polyester resin (n=10), and ground to plane the enamel and expose the dentin. The bonding site was delimited and samples were randomly assigned according to cavity preparation: (1) Er:YAG/1.0 mL/minute; (2) Er:YAG/1.5 mL/minute; (3) Er:YAG/2.0 mL/minute and (4) High speed handpiece/bur (control group). Samples were fixed to a metallic device, where composite resin cylinders were prepared. Subsequently, they were stored for 24 hours and subjected to a shear bond strength test (500N at 0.5 mm/minute). Results: Means (MPa) were: enamel: 1: 12.8; 2: 16.8; 3: 17.5; 4: 36.0 and Dentin: 1: 13.6; 2: 18.7; 3: 12.1; 4: 21.3. Data were submitted to ANOVA and Tukey`s test. Adhesion to enamel was more efficient than for dentin. The cavities prepared with conventional bur (control) presented higher statistically significant bond strength values (P<0.05) than for Er:YAG laser for both enamel and dentin. No significant differences were observed between water flow rates employed during enamel ablation. For dentin, the shear bond strength of 2.0 mL/minute water flow rate was lower than for 1.5 mL/minute and 1.0 mL/minute rates. The Er:YAG laser adversely affected shear bond strength of resin composite to both enamel and dentin, regardless of the water flow rate used.

Bloqueio do nervo alveolar mandibular com ropivacaína a 0,5 % em gatos

Objetivou-se, com este experimento, avaliar a ação da ropivacaína a 0,5% no bloqueio do nervo alveolar mandibular de gatos. Vinte gatos adultos, sem raça definida, machos ou fêmeas, receberam clorpromazina (1,0mg kg-1, VO) e propofol (3,0mg kg-1, IV). Ropivacaína a 0,5% foi administrada com uma agulha 13x3,8 em forma de L, inserida no ângulo da mandíbula direita, aproximadamente 1,0cm rostral ao processo angular e 0,5cm dorsal à superfície medial do ramo da mandíbula, a fim de depositá-la próximo ao nervo alveolar mandibular, no forame mandibular. As freqüências cardíaca e respiratória foram mensuradas antes da administração da clorpromazina, 20 minutos após administração desta (T0), 20 minutos após o bloqueio do nervo alveolar mandibular com ropivacaína (T20) e, em intervalos de 20 minutos, até a volta da sensibilidade na região anestesiada. Observou-se o período de latência e a duração da anestesia por meio do pinçamento da pele e gengiva da região lateral direita da mandíbula. Encontrou-se início da anestesia após 22 minutos, com duração de 164,25 minutos. Os parâmetros de freqüência cardíaca e freqüência respiratória tiveram alterações, porém sem significado clínico para a espécie. A ropivacaína a 0,5% anestesia a região dos dentes pré-molares, molares, caninos, incisivos, pele e mucosa oral e lábio inferior, sem causar efeitos colaterais.

Electrochemical studies with a Cu-5wt.%Ni alloy in 0.5 M H2SO4

The electrochemical behavior of the annealed Cu-5wt.%Ni alloy in 0.5 M H2SO4 was studied by means of open-circuit potential (E-OCP) measurements, cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and quasi-stationary linear potential sweep. The hydrodynamics of the system was also studied. This material is constituted by a single a, phase. The anodic behavior of a Cu-Ni alloy in H2SO4 consists fundamentally on the electrodissolution of Cu, its main component, and the formation of a sulfur-containing passive layer. The presence of Ni decreases the rate of Cu oxidation, mostly at high positive potentials. The impedance spectra, obtained for the unrotating electrode, can be interpreted in terms of a simple charge-transfer reaction across a surface layer. When the electrode is rotated, the occurrence of an inductive loop evidenced the existence of an adsorbed layer. All the resistance estimated from the proposed equivalent circuits diminished with the electrode rotation rate, emphasizing the influence of ion transport in the overall electrode process. The system presented two anodic Tafel slopes: 40 mV dec(-1) for E < 255 mV and 67 mV dec(-1) for E > 275 mV. A Tafel slope of 40 mV dec(-1) evidences that copper dissolution can be interpreted in terms of the mechanism proposed by Mattsson and Bockris. The second Tafel suggests that at potentials more positive than 275 mV, copper dissolves according to a mechanism that considers the disproportionation of adsorbed Cu(1) species. (C) 2003 Elsevier Ltd. All rights reserved.

Influence of exercise mode and maximal lactate-steady-state concentration on the validity of OBLA to predict maximal lactate-steady-state in active individuals

The aim of this study was to analyze the effects of exercise mode on the validity of onset of blood lactate accumulation (OBLA-3.5-mM fixed blood lactate concentration) to predict the work-rate at maximal lactate steady state (MLSSwork-rate). Eleven recreationally active mates (21.3 +/- 2.9 years, 72.8 +/- 6.7 kg, 1.78 +/- 0.1 m) performed randomly incremental tests to determine OBLA (stage duration of 3 min), and 2 to 4 constants work-rate exercise tests to directly determine maximal lactate steady state parameters on a cycle-ergometer and treadmill. For both exercise modes, the OBLA was significantly correlated to MLSSwork-rate, (cycling: r = 0.81 p = 0.002; running: r = 0.94, p < 0.001). OBLA (156.2 +/- 41.3 W) was lower than MLSSwork-rate (179.6 +/- 26.4 W) during cycling exercise (p = 0.007). However, for running exercise, there was no difference between OBLA (3.2 +/- 0.6 m s(-1)) and MLSSwork-rate (3.1 +/- 0.4 m s(-1)). The difference between OBLA and MLSSworkrate on the cycle-ergometer (r = 0.86; p < 0.001) and treadmill (r = 0.64; p = 0.048) was significantly related to the specific MLSS. We can conclude that the validity of OBLA on predicting MLSSwork-rate is dependent on exercise mode and that its disagreement is related to individual variations in MLSS. (C) 2007 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

Hysteroscopic myomectomy in a submucous fibroid near from tubal ostia and 5 mm from the serosa: A case report from the Endoscopy Service of Ginendo-RJ

This is a case report of a 27-year-old white woman, nuliparous, single, who presented a heavy menstrual flow with clots, dysmenorrhoea and anaemia. Gynaecological examination of the uterus revealed anteverted position, mobility, no pain, slight enlargement and right displacement. Magnetic resonance imaging of the pelvis showed a 29-mm submucous fibroid with intramural component more than 50%, type 2, in the posterior wall, with a 5-mm distance from serosa. In office hysteroscopy, a 30-mm submucous fibroid with an intramural component with more than 50%, type 2, near around 5 mm from left tubal ostia, classified in STEP-W submucous fibroids classification as score 6, group II, was noted. GnRH analogue was indicated for 3 months before intervention to treat anaemia. The patient was submitted to hysteroscopic myomectomy with direct mobilisation technique, with the fibroid completely removed without complications in a surgery which lasted for 52 min and 20 s. © 2008 Springer-Verlag.

Correlação da coalescência de microcavidades com as propriedades mecânicas e elétricas de fios para Tx e Dx de energia elétrica da liga base Al-0,5%Cu-[0,24-0,28]%Fe modificada com teores de silício

Neste trabalho, é feita uma tentativa para estabelecer a influência dos teores [0,5; 0,7 e 0,9]%Si, como agentes modificadores da liga Al-0,05%Cu-[0,24-0,28]%Fe, avaliada através de aspectos que levaram em conta parâmetros operacionais de vazamentos unidirecionais horizontais tais como velocidades (Vs) e taxas de solidificação (Tx). Após operações de corte e usinagem foram obtidos perfis cilíndricos, com diâmetros de 9,5mm e comprimento de 120mm, a partir dos quais, após operações de trabalho à frio, chegou-se a fios com diâmetros de 2,7; 3,0; 3,8 e 4,0mm. Estes perfis foram submetidos à caracterização elétrica, com base na condutividade elétrica, à caracterização mecânica, com base em ensaios tensão/deformação enfatizando o alongamento, e a caracterização estrutural em seções longitudinais, com ênfase na distribuição das partículas de segunda fase e no aspecto da fratura, na qual a metodologia de avaliação das dimensões das microcavidades se utiliza da razão do cumprimento (L) pela largura (W).

In vitro biomechanical comparison of six different fixation methods following 5-mm sagittal split advancement osteotomies

The sagittal split ramus osteotomy (SSRO) is a surgical technique used widely to treat many congenital and acquired mandibular discrepancies. Stabilization of the osteotomy site and the potential for skeletal relapse after the procedure are still major problems. The aim of this study was to compare the mechanical stability of six methods of rigid fixation in SSRO using a biomechanical test model. Sixty polyurethane replicas of human hemimandibles were divided into six groups. In group I, the osteotomies were fixed with two four-hole titanium miniplates; in group II, with one four-hole miniplate; in group III, with one four-hole miniplate + a bicortical screw; in group IV, with a grid miniplate; in group V, with a four-hole locking miniplate; and in group VI, with a six-hole miniplate. A linear load in the premolar region was applied to the hemimandibles. The resistance forces (N) needed to displace the distal segment by 1, 3, and 5 mm were recorded and the data transmitted from the load cell to a computer. One-way analysis of variance with Tukey's post hoc test was performed to compare the means between groups. For the three displacement conditions, there was a strong tendency for the 2.0-mm plate + screw and the grid plate to have higher values.

Nebulized 0.5, 2.5 and 5 ml L-epinephrine for post-extubation stridor in children: a prospective, randomized, double-blind clinical trial

Nebulized l-epinephrine has been recommended for the treatment of viral croup. However, the few studies assessing its effect on post-extubation stridor (PES) have shown conflicting results. We compared the efficacy and safety of nebulized l-epinephrine at three different doses for the treatment of PES. We conducted a prospective, randomized, double-blind trial including all consecutive children with a PES score of a parts per thousand yen4 (Westley score). The primary efficacy outcome was change in PES score at 40 min. A reduction of a parts per thousand yen2 points in stridor score was defined as clinically significant. A total of 96 patients were randomly assigned to receive one of three doses of nebulized l-epinephrine upon achieving a PES score of 4 or more following extubation. Stridor score and vital signs were recorded before treatment, and at 20, 40, 60 and 180 min after nebulization. Baseline characteristics were similar among all study groups. No significant difference was detected among the treatments based on change in Westley score by intent-to-treat analysis. In addition, the difference in the number of patients who clinically improved among the treatment groups was not significant (p = 0.54). Patients receiving 5 ml nebulized epinephrine had a significant increase of systolic and diastolic blood pressure at 40 and 180 min. Nebulized l-epinephrine at doses of 0.5, 2.5 and 5 ml demonstrated a lack of dose response in effect on PES and a modestly clinically significant increase in undesired side effects (heart rate and blood pressure) at higher doses.

Nitrate reduces the negative effect of UV radiation on photosynthesis and pigmentation in Gracilaria tenuistipitata (Rhodophyta): the photoprotection role of mycosporine-like amino acids

Photoprotection of the agarophyte red alga Gracilaria tenuistipitata against ultraviolet radiation (UVR) was investigated in algae submitted for 1 week to photosynthetically active radiation (PAR, 260 mu mol photons m(-2) s(-1)) or PAR + UVR (UV-A, 8.13 W m(-2) and UV-B, 0.42 W m(-2)) under different nitrogen concentrations: 0, 0.1, and 0.5 mM of NO3-. Photosynthetic pigments decreased during the time of the experiment mainly under low nitrogen supply and UVR. Incubation under high nitrogen supply (0.5 mM) sustained the photosynthetic levels over time. In contrast, mycosporine-like amino acids (MAAs) increased up to eightfold in the presence of UVR and 0.5 mM NO3-. Under PAR + UVR, maximal quantum yield was positively correlated to MAA abundance, whereas under PAR no correlation was found. The photosynthetic yield of algae cultivated during seven days under PAR + UVR was less affected by a 30-min exposure of high UVR (16 W m(-2)) and fully recovered after transferring to low PAR irradiances, whereas algae kept under PAR were more affected by UV exposure and no full recovery was observed. Growth rates decreased after three days in the presence of UVR and under low nitrate supply. However, these rates were similar when compared with treatments of PAR and PAR + UVR after seven days, with the exception of samples in 0 mM NO3-, indicating that the acclimation after one week's exposure is related to nitrate supply. In conclusion, the lowest negative effect of UVR on photosynthesis and growth rate in high N-supply-grown algae could be explained by the stimulation of photoprotection mechanisms, such as accumulation of MAAs. Photostimulation of MAA accumulation by UVR under high N supply was observed in G. tenuistipitata even after 20 years in culture without the induction of this photomorphogenic light signal.

Six-month clinical outcomes following implantation of the bioresorbable everolimus-eluting vascular scaffold in vessels smaller or larger than 2.5 mm

We investigated the 6-month clinical outcomes after implantation of second-generation 3.0-mm bioresorbable everolimus-eluting vascular scaffolds (BVS) in small coronary vessels (<2.5 mm).

In vitro resistance of articular chondrocytes to 5-Aminolevulinic acid based photodynamic therapy

OBJECTIVE: 5-Aminolevulinic acid based photodynamic therapy (5-ALA-PDT) has revealed promising results in the treatment of inflammatory joint diseases due to the sensitivity of inflamed synovial tissue. For 5-ALA-PDT to be safe and beneficial for intra-articular applications, resistance of chondrocytes is essential to prevent cartilage damage. As no data yet exist, the aim of the present study was to assess in vitro the response of the chondrocytes to 5-ALA-PDT and to compare with osteoblasts and synovial tissue derived cells. METHODS: Bovine articular chondrocytes, osteoblasts, and synovial cells were subjected to 5-ALA-PDT in cell culture. The PpIX accumulation and the function of the cells were assessed for up to 12 days. RESULTS: Bovine chondrocytes showed lower PpIX fluorescence upon incubation with 5-ALA (0.0-2.0 mM) for 4 hours as compared to osteoblasts and synovial cells suggesting a low PpIX accumulation. After incubation with 0.5 mM 5-ALA and application of light at a dose of 20 J/cm2, chondrocytes were functionally not affected (collagen type II and aggrecan mRNA, glycosaminoglycan synthesis) whereas a decrease in the proportion of viable cells was observed in osteoblasts and synovial cells (2+/-2% and 14+/-8%, respectively; chondrocytes 91+/-13%). Chondrocytes showed a 58% reduction of 5-ALA uptake using [3H]5-ALA as compared to osteoblasts and a lower mitochondrial content as assessed by the activity of the mitochondrial marker enzyme citrate synthase (9.2+/- 3.6 mU/mg protein) than osteoblasts (32.6+/-10.5 mU/mg) and synovial cells (60.0+/-10.8 mU/mg). The reduced uptake of 5-ALA and/or the low mitochondrial content, an adaptation to their in vivo environment and the site of PpIX synthesis, presumably explains the lower PpIX content in chondrocytes and their resistance against 5-ALA-PDT. CONCLUSION: 5-ALA-PDT might represent a treatment strategy in inflammatory joint diseases without endangering the cartilage function. However, further in vitro and in vivo experiments are required to confirm this data in the authentic environment of chondrocytes, the articular cartilage.

Snow Accumulation Rate on Qomolangma (Mount Everest), Himalaya: Synchroneity With Sites Across the Tibetan Plateau on 50-100 Year Timescales

Annual-layer thickness data, spanning AD 1534-2001, from an ice core from East Rongbuk Coll on Qomolangma (Mount Everest, Himalaya) yield an age-depth profile that deviates systematically from a constant accumulation-rate analytical model. The profile clearly shows that the mean accumulation rate has changed every 50-100 years. A numerical model was developed to determine the magnitude of these multi-decadal-scale rates. The model was used to obtain a time series of annual accumulation. The mean annual accumulation rate decreased from similar to 0.8 m ice equivalent in the 1500s to similar to 0.3 m in the mid-1800s. From similar to 1880 to similar to 1970 the rate increased. However, it has decreased since similar to 1970. Comparison with six other records from the Himalaya and the Tibetan Plateau shows that the changes in accumulation in East Rongbuk Col are broadly consistent with a regional pattern over much of the Plateau. This suggests that there may be an overarching mechanism controlling precipitation and mass balance over this area. However, a record from Dasuopu, only 125 km northwest of Qomolangma and 700 m higher than East Rongbuk Col, shows a maximum in accumulation during the 1800s, a time during which the East Rongbuk Col and Tibetan Plateau ice-core and tree-ring records show a minimum. This asynchroneity may be due to altitudinal or seasonal differences in monsoon versus westerly moisture sources or complex mountain meteorology.

Post-Depositional Movement of Methanesulphonic Acid at Law Dome, Antarctica, and the Influence of Accumulation Rate

A series of ice cores from sites with different snow-accumulation rates across Law Dome, East Antarctica, was investigated for methanesulphonic acid (MSA) movement. The precipitation at these sites (up to 35 km apart) is influenced by the same air masses, the principal difference being the accumulation rate. At the low-accumulation-rate W20k site (0.17 in ice equivalent), MSA was completely relocated from the summer to winter layer. Moderate movement was observed at the intermediate-accumulation-rate site (0.7 in ice equivalent), Dome Summit South (DSS), while there was no evidence of movement at the high-accumulation-rate DE08 site (1.4 in ice equivalent). The main DSS record of MSA covered the epoch AD 1727-2000 and was used to investigate temporal post-depositional changes. Co-deposition of MSA and sea-salt ions was observed of the surface layers, outside of the main summer MSA peak, which complicates interpretation of these peaks as evidence of movement in deeper layers. A seasonal study of the 273 year DSS record revealed MSA migration predominantly from summer into autumn (in the up-core direction), but this migration was suppressed during the Tambora (1815) and unknown (1809) volcanic eruption period, and enhanced during an epoch (1770-1800) with high summer nitrate levels. A complex interaction between the gradients in nss-sulphate, nitrate and sea salts (which are influenced by accumulation rate) is believed to control the rate and extent of movement of MSA.