Effects of incomplete combustion on atmospheric chemistry: Black carbon climate forcing and global carbon monoxide emissions

This thesis is actually the composition of two separate studies aimed at further understanding the role of incomplete combustion products on atmospheric chemistry. The first explores the sensitivity of black carbon (BC) forcing to aerosol vertical location since BC has an increased forcing per unit mass when it is located above reflective clouds. We used a column radiative transfer model to produce globally-averaged values of normalized direct radiative forcing (NDRF) for BC over and under different types of clouds. We developed a simple column-weighting scheme based on the mass fractions of BC that are over and under clouds in measured vertical profiles. The resulting NDRF is in good agreement with global 3-D model estimates, supporting the column-weighted model as a tool for exploring uncertainties due to diversity in vertical distribution. BC above low clouds accounts for about 20% of the global burden but 50% of the forcing. We estimate maximum-minimum spread in NDRF due to modeled profiles as about 40% and uncertainty as about 25%. Models overestimate BC in the upper troposphere compared with measurements; modeled NDRF might need to be reduced by about 15%. Redistributing BC within the lowest 4 km of the atmosphere affects modeled NDRF by only about 5% and cannot account for very high forcing estimates. The second study estimated global year 2000 carbon monoxide (CO) emissions using a traditional bottom-up inventory. We applied literature-derived emission factors to a variety of fuel and technology combinations. Combining these with regional fuel use and production data we produced CO emissions estimates that were separable by sector, fuel type, technology, and region. We estimated year 2000 stationary source emissions of 685.9 Tg/yr and 885 Tg/yr if we included adopted mobile sources from EDGAR v3.2FT2000. Open/biomass burning contributed most significantly to global CO burden, while the residential sector, primarily in Asia and Africa, were the largest contributors with respect to contained combustion sources. Industry production in Asia, including brick, cement, iron and steel-making, also contributed significantly to CO emissions. Our estimates of biofuel emissions are lower than most previously published bottom-up estimates while our other fuel emissions are generally in good agreement. Our values are also universally lower than recently estimated CO emissions from models using top-down methods.

Seismic waveform inversion for core-mantle boundary topography

International audience

Combination of Evolutionary Algorithms with Experimental Design, Traditional Optimization and Machine Learning

Evolutionary algorithms alone cannot solve optimization problems very efficiently since there are many random (not very rational) decisions in these algorithms. Combination of evolutionary algorithms and other techniques have been proven to be an efficient optimization methodology. In this talk, I will explain the basic ideas of our three algorithms along this line (1): Orthogonal genetic algorithm which treats crossover/mutation as an experimental design problem, (2) Multiobjective evolutionary algorithm based on decomposition (MOEA/D) which uses decomposition techniques from traditional mathematical programming in multiobjective optimization evolutionary algorithm, and (3) Regular model based multiobjective estimation of distribution algorithms (RM-MEDA) which uses the regular property and machine learning methods for improving multiobjective evolutionary algorithms.

Diseño de un modelo de nivelación de la producción en la empresa Lácteos San Antonio C. A. bajo metodología de manufactura esbelta

El presente trabajo de titulación tiene como propósito diseñar para la empresa Lácteos San Antonio C.A., un modelo que le permita eliminar los desniveles en la carga de trabajo u operaciones irregulares en el proceso de producción (Heijunka-Pull). El primer capítulo describe la situación actual de la empresa en relación a sus procesos de planificación de la producción. Además establece los problemas y objetivos a alcanzar, para finalmente exponer las herramientas que se utilizarán en la consecución de los mismos. En el segundo capítulo se detalla no sólo los principales conceptos y principios teóricos en los que se ha basado el modelo propuesto sino también se presenta el proceso que ha servido de guía para su elaboración. En el capítulo 3 se desarrolla el modelo de nivelación de la producción bajo la metodología de Manufactura esbelta (“Lean Manufacturing”), el cual le permitirá a la organización una mejor planificación de inventarios. Para ello se ha elaborado un presupuesto de ventas ajustado, cuyos datos han sido corregidos para una mejor aproximación a la demanda real mediante el cálculo del valor de los productos faltantes. Adicionalmente, se ha aplicado dos métodos de planificación para nivelar las órdenes de producción, los cuales buscan incrementar el nivel de disponibilidad mediante la reducción del tamaño de los lotes de producción y a través del incremento de la cantidad de productos por carga de trabajo.

Toppling Analysis of Precariously Balanced Rocks under Earthquake Excitation

Toppling analysis of a precariously balanced rock (PBR) can provide insights into the nature of ground motion that has not occurred at that location in the past and, by extension, realistic constraints on peak ground motions for use in engineering design. Earlier approaches have targeted simplistic 2-D models of the rock or modeled the rock-pedestal contact using spring-damper assemblies that require re-calibration for each rock. These analyses also assume that the rock does not slide on the pedestal. Here, a method to model PBRs in three dimensions is presented. The 3-D model is created from a point cloud of the rock, the pedestal, and their interface, obtained using Terrestrial Laser Scanning (TLS). The dynamic response of the model under earthquake excitation is simulated using a rigid body dynamics algorithm. The veracity of this approach is demonstrated by comparisons against data from shake table experiments. Fragility maps for toppling probability of the Echo Cliff PBR and the Pacifico PBR as a function of various ground motion parameters, rock-pedestal interface friction coefficient, and excitation direction are presented. The seismic hazard at these PBR locations is estimated using these maps. Additionally, these maps are used to assess whether the synthetic ground motions at these locations resulting from scenario earthquakes on the San Andreas Fault are realistic (toppling would indicate that the ground motions are unrealistically high).

Amazon forest structure generates diurnal and seasonal variability in light utilization.

The complex three-dimensional (3-D) structure of tropical forests generates a diversity of light environments for canopy and understory trees. Understanding diurnal and seasonal changes in light availability is critical for interpreting measurements of net ecosystem exchange and improving ecosystem models. Here, we used the Discrete Anisotropic Radiative Transfer (DART) model to simulate leaf absorption of photosynthetically active radiation (lAPAR) for an Amazon forest. The 3-D model scene was developed from airborne lidar data, and local measurements of leaf reflectance, aerosols, and PAR were used to model lAPAR under direct and diffuse illumination conditions. Simulated lAPAR under clear-sky and cloudy conditions was corrected for light saturation effects to estimate light utilization, the fraction of lAPAR available for photosynthesis. Although the fraction of incoming PAR absorbed by leaves was consistent throughout the year (0.80?0.82), light utilization varied seasonally (0.67?0.74), with minimum values during the Amazon dry season. Shadowing and light saturation effects moderated potential gains in forest productivity from increasing PAR during dry-season months when the diffuse fraction from clouds and aerosols was low. Comparisons between DART and other models highlighted the role of 3-D forest structure to account for seasonal changes in light utilization. Our findings highlight how directional illumination and forest 3-D structure combine to influence diurnal and seasonal variability in light utilization, independent of further changes in leaf area, leaf age, or environmental controls on canopy photosynthesis. Changing illumination geometry constitutes an alternative biophysical explanation for observed seasonality in Amazon forest productivity without changes in canopy phenology.

Healing effect of Terminalia chebula Retz extract on second-degree burns in rats

Purpose: To investigate the healing effect of Terminalia chebula Retz Extract (TCRE) on seconddegree burns in rats. Methods: Male Sprague Dawley (SD) rats, weighing 200 – 220 g, were subjected to deep seconddegree skin burns by electrical scald instrument. The animals were divided into three groups as follows: (1) second-degree burns model (control) group, (2) burns model treated with 1 % silver sulfadiazine (SSD) group, and (3) burns model treated with 100 mg·mL-1 TCRE group. On days 3, 7 and 14 following the administration of the drug/extract, the wound area and histopathological changes in rat epidermis were evaluated for the various groups. The minimum inhibitory concentration (MIC) of TCRE on Staphyloccocus aureus, Pseudomonas aeruginosa and Escherichia coli were also assessed separately. Results: On day 14, the mean wound area of TCRE treatment group (0.25 ± 0.06 cm2) was significantly smaller than that of the control rats (2.71 ± 0.20 cm2, p < 0.01). The histological results indicate that the inflammatory cells disappeared and were replaced by new granulation tissue in the group treated with 100 mg·mL-1 TCRE by day 14. Compared with SSD group rats, the inflammatory cells and fibroblast and granulation tissues of burnt rats treated with 100 mg·mL-1 TCRE were same as those of rats that had no burns. The antibacterial results revealed that the MIC of TCRE on Staphyloccocus aureus, Pseudomonas aeruginosa and Escherichia coli was 3.13, 12.5 and 6.25 mg·mL-1, respectively. Conclusion: Terminalia chebula Retz. has potentials to be developed as an effective medicinal herb for the treatment of second-degree burns.

Incentive based policies on climate change: taxes and tradable emssions permits

The reduction of Greenhouse Gases (GHG) plays a central role in the environmental policies considered by countries for implementation not only at its own level but also at supranational levels. This thesis is dedicated to investigate some aspects of two of the most relevant climate change policies. The first part is dedicated to emission permit markets and the second part to optimal carbon taxes. On emission permit markets we explore the strategic behavior of oligopolistic firms operating in polluting industrial sectors that are regulated by cap and trade systems. Our aim is to identify how market power influences the main results obtained under perfect competition assumptions and to understand how actions taken in one market affects the outcome of the other related market. A partial equilibrium model is developed for this purpose with specific abatement cost functions. In Chapter 2 we use the model to explain some of the most relevant literature results. In Chapter 3 the model is used to analyze different oligopolistic structures in the product market under the assumption of competitive permits market. There are two significant findings. Firstly, under the assumption of a Stackelberg oligopoly, firms have no incentives for lobbying in order to manipulate permit prices up, as they have under Cournot competition...

Modelling and predictive control techniques for building heating systems

Model predictive control (MPC) has often been referred to in literature as a potential method for more efficient control of building heating systems. Though a significant performance improvement can be achieved with an MPC strategy, the complexity introduced to the commissioning of the system is often prohibitive. Models are required which can capture the thermodynamic properties of the building with sufficient accuracy for meaningful predictions to be made. Furthermore, a large number of tuning weights may need to be determined to achieve a desired performance. For MPC to become a practicable alternative, these issues must be addressed. Acknowledging the impact of the external environment as well as the interaction of occupants on the thermal behaviour of the building, in this work, techniques have been developed for deriving building models from data in which large, unmeasured disturbances are present. A spatio-temporal filtering process was introduced to determine estimates of the disturbances from measured data, which were then incorporated with metaheuristic search techniques to derive high-order simulation models, capable of replicating the thermal dynamics of a building. While a high-order simulation model allowed for control strategies to be analysed and compared, low-order models were required for use within the MPC strategy itself. The disturbance estimation techniques were adapted for use with system-identification methods to derive such models. MPC formulations were then derived to enable a more straightforward commissioning process and implemented in a validated simulation platform. A prioritised-objective strategy was developed which allowed for the tuning parameters typically associated with an MPC cost function to be omitted from the formulation by separation of the conflicting requirements of comfort satisfaction and energy reduction within a lexicographic framework. The improved ability of the formulation to be set-up and reconfigured in faulted conditions was shown.

1H NMR Relaxation Characterization Of Hydrates

To distinguish the components of NMR signals from hydrated materials and to monitor their evolution after the addition of water to the powders, during the first two days of hydration. To implement the 3 Tau Model in a MATLAB script, called 3TM, provided with a Graphical User Interface (GUI), to easily use the 3 Tau Model with NMRD profiles. The 3 Tau Model, developed a few years ago is used for interpreting the dispersion (NMRD profiles, dependence on the Larmor frequency) of the longitudinal relaxation times, for liquids confined in porous media. This model describes the molecular dynamics of confined molecules by introducing three characteristic correlation times and additional outputs.

A planar geometrical model for representing multidimensional discrete spaces and multiple-valued logic functions /

Bibliography: p. 37-38.

Every normal logic program has a 2-valued semantics: theory, extensions, applications, implementations

Trabalho apresentado no âmbito do Doutoramento em Informática, como requisito parcial para obtenção do grau de Doutor em Informática

Control of a solar dryer through using a fuzzy logic and low-cost model-based sensor

Solar drying is one of the important processes used for extending the shelf life of agricultural products. Regarding consumer requirements, solar drying should be more suitable in terms of curtailing total drying time and preserving product quality. Therefore, the objective of this study was to develop a fuzzy logic-based control system, which performs a ?human-operator-like? control approach through using the previously developed low-cost model-based sensors. Fuzzy logic toolbox of MatLab and Borland C++ Builder tool were utilized to develop a required control system. An experimental solar dryer, constructed by CONA SOLAR (Austria) was used during the development of the control system. Sensirion sensors were used to characterize the drying air at different positions in the dryer, and also the smart sensor SMART-1 was applied to be able to include the rate of wood water extraction into the control system (the difference of absolute humidity of the air between the outlet and the inlet of solar dryer is considered by SMART-1 to be the extracted water). A comprehensive test over a 3 week period for different fuzzy control models has been performed, and data, obtained from these experiments, were analyzed. Findings from this study would suggest that the developed fuzzy logic-based control system is able to tackle difficulties, related to the control of solar dryer process.

A new approach to a model of the mammalian retina with optically programmable logic cells

This paper reports a model of the mammalian retina as well as an interpretation of some functions of the visual cortex. Its main objective is to simulate some of the behaviors observed at the different retina cells depending on the characteristics of the light impinging onto the photoreceptors. This simulation is carried out with a simple structure employed previously as basic building block of some optical computer architectures. Its possibility to perform any type of Boolean function allows a wide range of behaviors.

SYM-1, a program that detects symmetry of variable-valued logic functions /

Mode of access: Internet.