A rapid staining-assisted wood sampling method for PCR-based detection of pine wood nematode Bursaphelenchus xylophilus in Pinus massoniana wood tissue

For reasons of unequal distribution of more than one nematode species in wood, and limited availability of wood samples required for the PCR-based method for detecting pinewood nematodes in wood tissue of Pinus massoniana, a rapid staining-assisted wood sampling method aiding PCR-based detection of the pine wood nematode Bursaphelenchus xylophilus (Bx) in small wood samples of P. massoniana was developed in this study. This comprised a series of new techniques: sampling, mass estimations of nematodes using staining techniques, and lowest limit Bx nematode mass determination for PCR detection. The procedure was undertaken on three adjoining 5-mg wood cross-sections, of 0.5 · 0.5 · 0.015 cm dimension, that were cut from a wood sample of 0.5 · 0.5 · 0.5 cm initially, then the larger wood sample was stained by acid fuchsin, from which two 5-mg wood cross-sections (that adjoined the three 5-mg wood cross-sections, mentioned above) were cut. Nematode-staining-spots (NSSs) in each of the two stained sections were counted under a microscope at 100· magnification. If there were eight or more NSSs present, the adjoining three sections were used for PCR assays. The B. xylophilus – specific amplicon of 403 bp (DQ855275) was generated by PCR assay from 100.00% of 5-mg wood cross-sections that contained more than eight Bx NSSs by the PCR assay. The entire sampling procedure took only 10 min indicating that it is suitable for the fast estimation of nematode numbers in the wood of P. massonina as the prelimary sample selections for other more expensive Bx-detection methods such as PCR assay.

The Pine Wood Nematode: a personal view

The first report of the disease (“pine wilt disease”) associated with the pinewood nematode, goes back to 1905, when Yano reported an unusual decline of pines from Nagasaki. For a long time thereafter, the cause of he disease was sought, but without success. Because of the large number of insect species that were usually seen around and on infected trees, it had always been assumed that the causal agent would prove to be one of these. However, in 1971, Kiyohara and Tokushike found a nematode of the genus Bursaphelenchus in infected trees. The nematode found was multiplied on fungal culture, inoculated into healthy trees and then re-isolated from the resulting wilted trees. The subsequent published reports were impressive: this Bursaphelenchus species could kill fully-grown trees within a few months in the warmer areas of Japan, and could destroy complete forests of susceptible pine species within a few years. Pinus densiflora, P. thunbergii und P. luchuensis were particularly affected. In 1972, Mamiya and Kiyohara described the new species of nematode extracted from the wood of diseased pines; it was a named Bursaphelenchus lignicolus. Since 1975, the species has spread to the north of Japan, with the exception of the most northerly prefectures. In 1977, the loss of wood in the west of the country reached 80%. Probably as a result of unusually high summer temperatures and reduced rainfall in the years 1978 and 1979, the losses were more than 2 million m3 per year. From the beginning, B. lignicolus was always considered by Japanese scientists to be an exotic pest. But where did it come from? That this nematode could also cause damage in the USA became clear in 1979 when B. lignicolus was isolated in great numbers from wood of a 39 year-old pine tree (Pinus nigra) in Missouri which had suddenly died after the colour of its needles changed to a reddish-brown colour (Dropkin und Foudin, 2 1979). In 1981, B. lignicolus was synonymised by Nickle et al. with B. xylophilus which had been found for the first time in the USA as far back as 1929, and reported by Steiner and Buhrer in 1934. It had originally been named Aphelenchoides xylophilus, the wood-inhabiting Aphelenchoides but was recognised by Nickle, in 1970,to belong in the genus Bursaphelenchus. Its common name in the USA was the "pine wood nematode" (PWN. After its detection in Missouri, it became known that B. xylophilus was widespread throughout the USA and Canada. It occurred there on native species of conifers where, as a rule, it did not show the symptoms of pine wilt disease unless susceptible species were stressed eg., by high temperature. This fact was an illuminating piece of evidence that North America could be the homeland of PWN. Dwinell (1993) later reported the presence of B. xylophilus in Mexico. The main vector of the PWN in Japan was shown to be the long-horned beetle Monochamus alternatus, belonging to the family Cerambycidae. This beetle lays its eggs in dead or dying trees where the developing larvae then feed in the cambium layer. It was already known in Japan in the 19th century but in the 1930s, it was said to be present in most areas of Japan, but was generally uncommon. However, with the spread of the pine wilt disease, and the resulting increase of weakened trees that could act as breeding sites for beetles, the populations of Monochamus spp. increased significantly In North America, other Monochamus species transmit PWN, and the main vector is M. carolinensis. In Japan, there are also other, less efficient vectors in the genus Monochamus. Possibly, all Monochamus species that breed in conifers can transmit the PWN. The occasional transmission by less efficient species of Monochamus or by some of the many other beetle genera in the bark or wood is of little significance. In Europe, M. galloprovincialis and M. sutor transmits the closely related species B. mucronatus. Some speculate that these two insect species are “standing by” and waiting for the arrival of B. xylophilus. In 1982, the nematode was detected and China. It was first found in dead pines near the Zhongshan Monument of Nanjing (CHENG et. al. 1983); 265 trees were then killed by pine wilt disease. Despite great efforts at eradication in China, the nematode spread further and pine wilt disease has been 3 reported from parts of the provinces of Jiangsu, Anhui, Guangdong, Shandong, Zhejiang and Hubei (YANG, 2003). In 1986, the spread of the PWN to Taiwan was discovered and in 1989, the nematode was reported to be present in the Republic of Korea where it had first been detected in Pinus thunbergii and P. densiflora. It was though to have been introduced with packing material from Japan. PWN was advancing. In 1984, B. xylophilus was found in wood chips imported into Finland from the USA and Canada, and this was the impetus to establish phytosanitary measures to prevent any possible spread into Europe. Finland prohibited the import of coniferous wood chips from these sources, and the other Nordic countries soon followed suit. EPPO (the European and Mediterranean Plant Protection Organization) made a recommendation to its member countries in 1986 to refuse wood imports from infested countries. With its Directive of 1989 (77/93 EEC), the European Community (later called the European Union or EU) recognised the potential danger of B. xylophilus for European forests and imposed restrictions on imports into the Europe. PWN was placed on the quarantine list of the EU and also of other European countries. Later, in 1991, a dispensation was allowed by the Commission of the EU(92/13 EEC) for coniferous wood from North America provided that certain specified requirements were fulfilled that would prevent introduction.

Hygrothermal performance of wood-hemp insulation in timber frame wall panels with and without a vapour barrier

An in situ experiment on a full-scale timber frame test building was carried out to study the hygrothermal performance of wood-hemp composite insulation in timber frame wall panels with and without a vapour barrier. The heat transfer properties and the likelihood of mould growth and condensation in the panels were compared. Step changes in the internal relative humidity were performed to explore the effects of high, normal and low internal moisture loads on the wall panels. No significant difference in the average equivalent thermal transmittance (U-values) between the panels with and without a vapour barrier was observed. The average equivalent U-values of the panels were close to the U-values calculated from the manufacturers’ declared thermal conductivity values of the insulation. The likelihood of condensation was higher at the interface of the wood-hemp insulation and the oriented strand board (OSB) in the panel without a vapour barrier. In terms of the parametric assessment of the mould germination potential, the relative humidity, the temperature and the exposure conditions in the insulation-OSB interfaces of the panel without a vapour barrier were found to be more favourable to the germination of mould spores. Nonetheless, when the insulations were dismantled, no mould was visually detected.

Experimental and numerical evaluation of composite repairs on wood beams damaged by cross-graining

An experimental and Finite Element study was performed on the bending behaviour of wood beams of the Pinus Pinaster species repaired with adhesively-bonded carbon–epoxy patches, after sustaining damage by cross-grain failure. This damage is characterized by crack growth at a small angle to the beams longitudinal axis, due to misalignment between the wood fibres and the beam axis. Cross-grain failure can occur in large-scale in a wood member when trees that have grown spirally or with a pronounced taper are cut for lumber. Three patch lengths were tested. The simulations include the possibility of cohesive fracture of the adhesive layer, failure within the wood beam in two propagation planes and patch interlaminar failure, by the use of cohesive zone modelling. The respective cohesive properties were estimated either by an inverse method or from the literature. The comparison with the tests allowed the validation of the proposed methodology, opening a good perspective for the reduction of costs in the design stages of these repairs due to extensive experimentation.

Experimental Reinforcement of Wood Beams

Rehabilitation is becoming more and more usual in the construction sector in Portugal. The introduction of newer construction materials and technical know-how of integrating different materials for achieving desired engineering goals is an important step to the development of the sector. Wood industry is also getting more and more adapted to composite technologies with the introduction of the so called “highly engineered wood products” and with the use of modification treatments. This work is an attempt to explain the viability of using stainless steel and glass fibre reinforced polymer (GFRP) as reinforcements in wood beams. This thesis specifically focuses on the flexural behaviour of Portuguese Pine unmodified and modified wood beams. Two types of modification were used: 1,3-dimethylol-4,5- dihydroxyethyleneurea (DMDHEU) resin and amid wax. The behaviour of the material was analysed with a nonlinear model. The latter model simulates the behaviour of the reinforced wood beams under flexural loading. Small-scale beams (1:15) were experimented in flexural bending and the experimental results obtained were compared with the analytical model results. The experiments confirm the viability of the reinforcing schemes and the working procedures. Experimental results showed fair agreement with the nonlinear model. A strength increase between 15% and 80% was achieved. Stiffness increased by 40% to 50% in beams reinforced with steel but no significant increase was achieved with the glass fibre reinforcement.

Enhancement of ultrafiltration process by pretreatment in recovery of hemicelluloses from wood extracts

Hemicelluloses are potential raw material for several items produced in future wood-based biorefineries. One possible method for recovering hemicelluloses from wood extracts is ultrafiltration (UF). However, low filtration capacities and severe fouling restrict the use of tight UF membranes in the treatment of wood extracts. The lack of suitable commercial membranes creates a need for pretreatment which would decrease fouling and increase the filtration capacity. This thesis focuses on the evaluation of the possibility to improve the filtration capacity and decrease fouling with the pretreatment of wood extracts. Methods which remove harmful compounds and methods which degrade them are studied, as well as combinations of the methods. The tested pretreatments have an influence on both the concentration of different compounds and the molecular mass distribution of the compounds in the extract. This study revealed that in addition to which kind of compounds were removed, also the change in molecular size distribution affected the filtration capacity significantly. It was shown that the most harmful compounds for the filtration capacity of the hydrophobic 5 kDa membrane were the ones capable of permeating the membrane and fouling also the inner membrane structure. Naturally, the size of the most harmful compounds depends on the used UF membrane and is thus case-specific. However, in the choice of the pretreatment method, the focus should be on the removal of harmful compound sizes rather than merely on the total amount of removed foulants. The results proved that filtration capacity can be increased with both adsorptive and oxidative pretreatments even by hundreds of per cents. For instance, the use of XAD7 and XAD16 adsorbents increased the average flux in the UF of a birch extract from nearly zero to 107 kg/(m2h) and 175 kg/(m2h), respectively. In the treatment of a spruce extract, oxidation by pulsed corona discharge (PCD) increased the flux in UF from 46 kg/(m2h) to 158 kg/(m2h). Moreover, when a birch extract batch was treated with laccase enzyme, the flux in UF increased from 15 kg/(m2h) to 36 kg/(m2h). However, fouling was decreased only by adsorptive pretreatment while oxidative methods had a negligible or even negative impact on it. This demonstrates that filtration capacity and fouling are affected by different compounds and mechanisms. The results of this thesis show that filtration capacity can be improved and fouling decreased through appropriate pretreatment. However, the choice of the best possible pretreatment is case-specific and depends on the wood extract and the membrane used. Finding the best option requires information on the extract content and membrane characteristics as well as on the filtration performance of the membrane in the prevailing conditions and a multivariate approach. On the basis of this study, it can be roughly concluded that adsorptive pretreatment improves the filtration capacity and decreases fouling rather reliably, but it may lead to significant hemicellulose losses. Oxidation reduces the loss of valuable hemicelluloses and could improve the filtration capacity, but fouling challenges may remain. Combining oxidation with adsorptive pretreatment was not a solution for avoiding hemicellulose losses in the tested cases.

The efficacy of anti-predator behaviour in the wood fog tadpole (Rana sylvatica) /

Activity has been suggested as an important behaviour that is tightly linked with predator avoidance in tadpoles. In this thesis I examine predator-prey relationships using wood frog tadpoles {Rana sylvaticd) as prey and dragonfly larvae {AnaxJunius) and backswimmers {Notonecta undulatd) as predators. I explore the role of prey activity in predator attack rates, prey response to single and multiple predator introductions, and prey survivorship. The data suggest that Anax is the more successful predator, able to capture both active and inactive tadpoles. In contrast, Notonecta strike at inactive prey less frequently and are seldom successftil when they do. A mesocosm study revealed that the presence of any predator resulted in reduced activity level of tadpoles. Each predator species alone had similar effects on tadpole activity, as did the combined predator treatment. Tadpole survivorship, however, differed significantly among both predator treatments and prey populations. Tadpwles in the combined predator treatment had enhanced risk; survivorship was lower than that expected if the two predators had additive effects. Differences in survivorship among wood frog populations showed that tadpoles from a lake habitat had the lowest survivorship, those from a shallow pond habitat had an intermediate survivorship, and tadpoles from a marsh habitat had the highest survivorship. The frequency of interactions with predators in the native habitat may be driving the population differences observed. In conclusion, results from this study show that complex interactions exist between predators, prey, and the environment, with activity playing a key role in the survival of tadpoles.

Welland Canal Survey of Lands Samuel Wood Esquire, 1828

Survey map and description of Samuel Wood's land created by The Welland Canal Company. Included is a written description of the land along with a drawing of the land. The same description of the land is also in a deed dated Septmeber 16, 1828 (see county registry 739). Noteable features include; the canal, the tow path, the tow path bridge. Surveyor notes are seen in pencil on the map. The original deed for the land is dated May 16, 1828.

Joanna E. Wood short stories, 1898-1900

Joanna Ellen Wood (1867-1927) was an acclaimed Canadian author who wrote several novels and short stories. Wood was born in Scotland, but emigrated to Canada with her family in 1869. In 1874 her father purchased a farm overlooking the Niagara River at Queenston. It is believed she was supported by her brother William, who encouraged her writing. She was based in New York City from 1887-1901, using William’s business address there to receive correspondence while she traveled or spent time in Queenston. Around 1906, Wood moved with her mother to Niagara-on-the-Lake, where she joined the Niagara Historical Society. By 1914, she was living in Buffalo, but later spent time at her sisters’ homes. It was at her sister’s home in Detroit where she suffered a stroke and died in 1927. Wood’s literary career was short-lived. She published her first novel, The Untempered Wind , in 1894, and a second novel, Judith Moore …, in 1898. Both novels received critical acclaim, and a third novel, Farden Ha', followed in 1902. Unfortunately the majority of Wood’s numerous and award-winning writings cannot be found. Her career peaked in 1901, when she was the highest paid Canadian fiction writer. For unknown reasons, her career abruptly ceased in 1902, with no further publications or mention made of her in the Canadian Magazine.

Letter to the Honourable William Dickson at Wood Lawn, Youngstown, New York from W. Bushby

Letter to the Honourable William Dickson at Wood Lawn, Youngstown, New York from W. Bushby. He says that Mary is probably going to marry Mr. Lyon and he asks if there is any chance that Mr. Dickson could come for the wedding. He says he heard about the death of George Hamilton from John Hamilton (3 ½ pages, handwritten), Sept. 29, 1836.

Inventory of goods and chattels belonging to Samuel Wood and delivered to the Honourable William Dickson

Inventory of goods and chattels belonging to Samuel Wood and delivered to the Honourable William Dickson (double-sided, handwritten page), Dec. 10, 1828.

Rubber Solution Adhesives for Wood-to-Wood Bonding

Rubber solutions were prepared and used for bonding wood pieces. The effect of the variation of chlorinated natural rubber (CNR) and phenolformaldehyde (PF) resin in the adhesive solutions on lap shear strength was determined. Natural rubber and neoprene-based adhesive solutions were compared for their lap shear strength. The storage stability of the adhesive prepared was determined. The change in lap shear strength before and after being placed in cold water, hot water, acid, and alkali was tested. The bonding character of these adhesives was compared with different commercially available solution adhesives. The room-temperature aging resistance of wood joints was also determined. In all the studies, the adhesive prepared in the laboratory was found to be superior compared to the commercial adhesives.

Environmental Impacts of Chromated Copper Arsenate (CCA) Treated Rubber Wood for Aquatic Applications

Faculty of Marine Sciences, Cochin University of Science and Technology