Congestion probability routing in virtual path ATM network

This dissertation focuses on the problem of providing mechanisms for routing point to point and multipoint connections in ATM networks. In general the notion of multipoint connection refers to connections that involve a group of users with more than two members. The main objective of this dissertation is to contribute to design efficient routing protocols with alterative routes in fully connected VP-based ATM Networks for call establishment of point to point and multipoint VC connections. An efficient route should be computed during this connection establishment phase.

Dynamic management and restoration of virtual paths in broadband networks based on distributed software agents

La gestió de xarxes és un camp molt ampli i inclou molts aspectes diferents. Aquesta tesi doctoral està centrada en la gestió dels recursos en les xarxes de banda ampla que disposin de mecanismes per fer reserves de recursos, com per exemple Asynchronous Transfer Mode (ATM) o Multi-Protocol Label Switching (MPLS). Es poden establir xarxes lògiques utilitzant els Virtual Paths (VP) d'ATM o els Label Switched Paths (LSP) de MPLS, als que anomenem genèricament camins lògics. Els usuaris de la xarxa utilitzen doncs aquests camins lògics, que poden tenir recursos assignats, per establir les seves comunicacions. A més, els camins lògics són molt flexibles i les seves característiques es poden canviar dinàmicament. Aquest treball, se centra, en particular, en la gestió dinàmica d'aquesta xarxa lògica per tal de maximitzar-ne el rendiment i adaptar-la a les connexions ofertes. En aquest escenari, hi ha diversos mecanismes que poden afectar i modificar les característiques dels camins lògics (ample de banda, ruta, etc.). Aquests mecanismes inclouen els de balanceig de la càrrega (reassignació d'ample de banda i reencaminament) i els de restauració de fallades (ús de camins lògics de backup). Aquests dos mecanismes poden modificar la xarxa lògica i gestionar els recursos (ample de banda) dels enllaços físics. Per tant, existeix la necessitat de coordinar aquests mecanismes per evitar possibles interferències. La gestió de recursos convencional que fa ús de la xarxa lògica, recalcula periòdicament (per exemple cada hora o cada dia) tota la xarxa lògica d'una forma centralitzada. Això introdueix el problema que els reajustaments de la xarxa lògica no es realitzen en el moment en què realment hi ha problemes. D'altra banda també introdueix la necessitat de mantenir una visió centralitzada de tota la xarxa. En aquesta tesi, es proposa una arquitectura distribuïda basada en un sistema multi agent. L'objectiu principal d'aquesta arquitectura és realitzar de forma conjunta i coordinada la gestió de recursos a nivell de xarxa lògica, integrant els mecanismes de reajustament d'ample de banda amb els mecanismes de restauració preplanejada, inclosa la gestió de l'ample de banda reservada per a la restauració. Es proposa que aquesta gestió es porti a terme d'una forma contínua, no periòdica, actuant quan es detecta el problema (quan un camí lògic està congestionat, o sigui, quan està rebutjant peticions de connexió dels usuaris perquè està saturat) i d'una forma completament distribuïda, o sigui, sense mantenir una visió global de la xarxa. Així doncs, l'arquitectura proposada realitza petits rearranjaments a la xarxa lògica adaptant-la d'una forma contínua a la demanda dels usuaris. L'arquitectura proposada també té en consideració altres objectius com l'escalabilitat, la modularitat, la robustesa, la flexibilitat i la simplicitat. El sistema multi agent proposat està estructurat en dues capes d'agents: els agents de monitorització (M) i els de rendiment (P). Aquests agents estan situats en els diferents nodes de la xarxa: hi ha un agent P i diversos agents M a cada node; aquests últims subordinats als P. Per tant l'arquitectura proposada es pot veure com una jerarquia d'agents. Cada agent és responsable de monitoritzar i controlar els recursos als que està assignat. S'han realitzat diferents experiments utilitzant un simulador distribuït a nivell de connexió proposat per nosaltres mateixos. Els resultats mostren que l'arquitectura proposada és capaç de realitzar les tasques assignades de detecció de la congestió, reassignació dinàmica d'ample de banda i reencaminament d'una forma coordinada amb els mecanismes de restauració preplanejada i gestió de l'ample de banda reservat per la restauració. L'arquitectura distribuïda ofereix una escalabilitat i robustesa acceptables gràcies a la seva flexibilitat i modularitat.

Supporting Computer-supported collaborative work (CSCW) in conceptual design

In order to gain a better understanding of online conceptual collaborative design processes this paper investigates how student designers make use of a shared virtual synchronous environment when engaged in conceptual design. The software enables users to talk to each other and share sketches when they are remotely located. The paper describes a novel methodology for observing and analysing collaborative design processes by adapting the concepts of grounded theory. Rather than concentrating on narrow aspects of the final artefacts, emerging “themes” are generated that provide a broader picture of collaborative design process and context descriptions. Findings on the themes of “grounding – mutual understanding” and “support creativity” complement findings from other research, while important themes associated with “near-synchrony” have not been emphasised in other research. From the study, a series of design recommendations are made for the development of tools to support online computer-supported collaborative work in design using a shared virtual environment.

Design for design: support for creative practice in computer-supported collaborative work (CSCW) in design

This paper describes a novel methodology for observing and analysing collaborative design by using the concepts of cognitive dimensions related to concept-based misfit analysis. The study aims at gaining an insight into support for creative practice of graphical communication in collaborative design processes of designers while sketching within a shared white board and audio conferencing environment. Empirical data on design processes have been obtained from observation of groups of student designers solving an interior space-planning problem of a lounge-diner in a shared virtual environment. The results of the study provide recommendations for the design and development of interactive systems to support such collaborative design activities.

Using historical lesion volume data in the design of a new phase II clinical trial in acute stroke

Background and Purpose-Clinical research into the treatment of acute stroke is complicated, is costly, and has often been unsuccessful. Developments in imaging technology based on computed tomography and magnetic resonance imaging scans offer opportunities for screening experimental therapies during phase II testing so as to deliver only the most promising interventions to phase III. We discuss the design and the appropriate sample size for phase II studies in stroke based on lesion volume. Methods-Determination of the relation between analyses of lesion volumes and of neurologic outcomes is illustrated using data from placebo trial patients from the Virtual International Stroke Trials Archive. The size of an effect on lesion volume that would lead to a clinically relevant treatment effect in terms of a measure, such as modified Rankin score (mRS), is found. The sample size to detect that magnitude of effect on lesion volume is then calculated. Simulation is used to evaluate different criteria for proceeding from phase II to phase III. Results-The odds ratios for mRS correspond roughly to the square root of odds ratios for lesion volume, implying that for equivalent power specifications, sample sizes based on lesion volumes should be about one fourth of those based on mRS. Relaxation of power requirements, appropriate for phase II, lead to further sample size reductions. For example, a phase III trial comparing a novel treatment with placebo with a total sample size of 1518 patients might be motivated from a phase II trial of 126 patients comparing the same 2 treatment arms. Discussion-Definitive phase III trials in stroke should aim to demonstrate significant effects of treatment on clinical outcomes. However, more direct outcomes such as lesion volume can be useful in phase II for determining whether such phase III trials should be undertaken in the first place. (Stroke. 2009;40:1347-1352.)

Developing an engaging virtual action learning programme for SME managers – A UK perspective

In this paper we present results from an EU-funded project with the aim of examining the adaptation of e-learning to meet the needs of managers in different contexts. A set of design considerations is elucidated. These principles were derived from an analysis of five completed projects. This was followed by focus group discussion in the UK to test the principles derived.. These focus group were planned so as to gain greater clarity in the design of e-learning programmes aimed at UK-based SME leaders and managers. This paper starts by looking at the importance of SME management development for the economic wellbeing of the community and goes on to review research into issues in engaging managers in development activities. The results of a review of an earlier experimental programme (ESeN) are presented as it formed part of the process which led to the identification of theoretical design principles then tested in the focus groups. Finally, recommendations are presented for SME e-learning providers as well as areas for further research.

Finite element aided design evolution of composite leaf spring

This paper shows the process of the virtual production development of the mechanical connection between the top leaf of a dual composite leaf spring system to a shackle using finite element methods. The commercial FEA package MSC/MARC has been used for the analysis. In the original design the joint was based on a closed eye-end. Full scale testing results showed that this configuration achieved the vertical proof load of 150 kN and 1 million cycles of fatigue load. However, a problem with delamination occurred at the interface between the fibres going around the eye and the main leaf body. To overcome this problem, a second design was tried using transverse bandages of woven glass fibre reinforced tape to wrap the section that is prone to delaminate. In this case, the maximum interlaminar shear stress was reduced by a certain amount but it was still higher than the material’s shear strength. Based on the fact that, even with delamination, the top leaf spring still sustained the maximum static and fatigue loads required, the third design was proposed with an open eye-end, eliminating altogether the interface where the maximum shear stress occurs. The maximum shear stress predicted by FEA is reduced significantly and a safety factor of around 2 has been obtained. Thus, a successful and safe design has been achieved.

Virtual reality Post Traumatic Stress Disorder (PTSD) exposure therapy results with active duty Iraq war combatants

Post Traumatic Stress Disorder (PTSD) is reported to be caused by traumatic events that are outside the range of usual human experience including (but not limited to) military combat, violent personal assault, being kidnapped or taken hostage and terrorist attacks. Initial data suggests that at least 1 out of 6 Iraq War veterans are exhibiting symptoms of depression, anxiety and PTSD. Virtual Reality (VR) delivered exposure therapy for PTSD has been used with reports of positive outcomes. The aim of the current paper is to present the rationale and brief description of a Virtual Iraq PTSD VR therapy application and present initial findings from its use with PTSD patients. Thus far, Virtual Iraq consists of a series of customizable virtual scenarios designed to represent relevant Middle Eastern VR contexts for exposure therapy, including a city and desert road convoy environment. User-centered design feedback needed to iteratively evolve the system was gathered from returning Iraq War veterans in the USA and from a system deployed in Iraq and tested by an Army Combat Stress Control Team. Results from an open clinical trial at San Diego Naval Medical Center of the first 18 treatment completers indicate that 14 no longer meet PTSD diagnostic criteria at post-treatment, with only one not maintaining treatment gains at 3 month follow-up. Clinical tests are also currently underway at Ft. Lewis, Emory University, Weill Cornell Medical College, Walter Reed Army Medical Center and 10 other sites. Other sites are preparing to use the application for a variety of PTSD and VR research purposes.

Design and development of a haptic dental training system - hapTEL

This paper presents a novel design of a virtual dental training system (hapTEL) using haptic technology. The system allows dental students to learn and practice procedures such as dental drilling, caries removal and cavity preparation for tooth restoration. This paper focuses on the hardware design, development and evaluation aspects in relation to the dental training and educational requirements. Detailed discussions on how the system offers dental students a natural operational position are documented. An innovative design of measuring and connecting the dental tools to the haptic device is also shown. Evaluation of the impact on teaching and learning is discussed.

A virtual head-stick rehabilitation robot system

For individuals with upper-extremity motor disabilities, the head-stick is a simple and intuitive means of performing manipulations because it provides direct proprioceptive information to the user. Through practice and use of inherent proprioceptive cues, users may become quite adept at using the head-stick for a number of different tasks. The traditional head-stick is limited, however, to the user's achievable range of head motion and force generation, which may be insufficient for many tasks. The authors describe an interface to a robot system which emulates the proprioceptive qualities of a traditional head-stick while also allowing for augmented end-effector ranges of force and motion. The design and implementation of the system in terms of coordinate transforms, bilateral telemanipulator architecture, safety systems, and system identification of the master is described, in addition to preliminary evaluation results.

Virtual reality as a visualisation tool: benefits and constraints

The benefits and applications of virtual reality (VR) in the construction industry have been investigated for almost a decade. However, the practical implementation of VR in the construction industry has yet to reach maturity owing to technical constraints. The need for effective information management presents challenges: both transfer of building data to, and organisation of building information within, the virtual environment require consideration. This paper reviews the applications and benefits of VR in the built environment field and reports on a collaboration between Loughborough University and South Bank University to overcome constraints on the use of the overall VR model for whole lifecycle visualisation. The work at each research centre is concerned with an aspect of information management within VR applications for the built environment, and both data transfer and internal data organisation have been investigated. In this paper, similarities and differences between computer-aided design (CAD) and VR packages are first discussed. Three different approaches to the creation of VR models during the design stage are identified and described, with a view to providing sharing understanding across the interdiscipliary groups involved. The suitable organisation of building information within the virtual environment is then further investigated. This work focused on the visualisation of the degradation of a building, through its lifespan, with the view to provide a visual aid for developing an effective and economic project maintenance programme. Finally consideration is given to the potential of emerging standards to facilitate an integrated use of VR. The convergence towards similar data structures in VR and other construction packages may enable visualisation to be better utilised in the overall lifecycle model.

Construction safety and digital design: a review

As digital technologies become widely used in designing buildings and infrastructure, questions arise about their impacts on construction safety. This review explores relationships between construction safety and digital design practices with the aim of fostering and directing further research. It surveys state-of-the-art research on databases, virtual reality, geographic information systems, 4D CAD, building information modeling and sensing technologies, finding various digital tools for addressing safety issues in the construction phase, but few tools to support design for construction safety. It also considers a literature on safety critical, digital and design practices that raises a general concern about ‘mindlessness’ in the use of technologies, and has implications for the emerging research agenda around construction safety and digital design. Bringing these strands of literature together suggests new kinds of interventions, such as the development of tools and processes for using digital models to promote mindfulness through multi-party collaboration on safety

Virtual reality Post Traumatic Stress Disorder (PTSD) exposure therapy results with active duty OIF/OEF service members

Posttraumatic stress disorder (PTSD) is reported to be caused by exposure to traumatic events including (but not limited to) military combat, violent personal assault, being kidnapped or taken hostage and terrorist attacks. Initial data suggest that at least 1 out of 6 Iraq War veterans are exhibiting symptoms of depression, anxiety and PTSD. Virtual reality (VR) delivered exposure therapy for PTSD has been used with reports of positive outcomes. The aim of the current paper, is to present the rationale and brief description of a Virtual Iraq/Afghanistan PTSD VR therapy application and present initial findings from its use with PTSD patients. Thus far, Virtual Iraq/Afghanistan consists of a series of customizable virtual scenarios designed to represent relevant Middle Eastern VR contexts for exposure therapy, including a city and desert road convoy environment. User-centered design feedback, needed to iteratively evolve the system, was gathered from returning Iraq War veterans in the USA and from a system deployed in Iraq and tested by an Army Combat Stress Control Team. Results from an open clinical trial at San Diego Naval Medical Center of the first 20 treatment completers indicate that 16 no longer met PTSD screening criteria at post-treatment, with only one not maintaining treatment gains at 3 month follow-up.

"Where am I?" Impact of display and content variables on spatial presence and comprehension in virtual environments

Forgetting immediate physical reality and having awareness of one�s location in the simulated world is critical to enjoyment and performance in virtual environments be it an interactive 3D game such as Quake or an online virtual 3d community space such as Second Life. Answer to the question "where am I?" at two levels, whether the locus is in the immediate real world as opposed to the virtual world and whether one is aware of the spatial co-ordinates of that locus, hold the key to any virtual 3D experience. While 3D environments, especially virtual environments and their impact on spatial comprehension has been studied in disciplines such as architecture, it is difficult to determine the relative contributions of specific attributes such as screen size or stereoscopy towards spatial comprehension since most of them treat the technology as monolith (box-centered). Using a variable-centered approach put forth by Nass and Mason (1990) which breaks down the technology into its component variables and their corresponding values as its theoretical basis, this paper looks at the contributions of five variables (Stereoscopy, screen size, field of view, level of realism and level of detail) common to most virtual environments on spatial comprehension and presence. The variable centered approach can be daunting as the increase in the number of variables can exponentially increase the number of conditions and resources required. We overcome this drawback posed by adoption of such a theoretical approach by the use of a fractional factorial design for the experiment. This study has completed the first wave of data collection and starting the next phase in January 2007 and expected to complete by February 2007. Theoretical and practical implications of the study are discussed.

Using virtual environments for trigger identification in addiction treatment

This paper presents a novel application of virtual environments to assist in encouraging behavior change in individuals who misuse drugs or alcohol. We describe the user-centered design of a series of scenes to engage users in the identification of triggers and to encourage discussions about relevant coping skills. Results from the initial testing of this application with six service users showed variation in user responses. Results also suggested that the system should encourage group discussion and that it was linked to a small improvement in users’ confidence in understanding and identifying triggers.