Analise técnico-econômica de um gaseificador Downdraft e de filtros para limpeza de gás de síntese

The biomass gasification systems have been used for a long time and prove to be a good alternative to the generation of energy problems. This type of management requires a simple installation and maintenance which gives them a high availability. In Biomass project via Call CTEnerg 33/2006-1, funded by the Ministry of Science and Technology - MCT - Brazil, the Group Energy Systems Optimization – GOSE - at FEG - UNESP built and tested two prototypes of gasifiers. These is fed with 25 kg / h of dry wood (chips), and 50 Nm3 / h of air to produce gas at a flow rate of approximately 70 Nm3 / h of wood (syngas) at a temperature approximately 600 ° C. In this work of graduation, studies were conducted on the materials used in both the gasifier as well as cleaning the filter synthesis gases. The system of gas cleaning and conditioning is vital to ensure the life of the Internal Combustion Engine. In this case the studies of different filters for small gasification systems (properties, materials used, characteristics, types, etc.) are very relevant to its use in the prototype of the college campus. Were also performed a technical and economic analysis of a cogeneration system that consists in the combination of the downdraft gasifier studied in this work, an internal combustion engine, two heat exchangers and a SRA (absorption system refrigerator). Were calculated the costs of electricity generation, hot water and cold water. Finally, we analyzed the economic feasibility of the project

Estudo das características fluidodinâmicas do bagaço de cana de açúcar para aplicações da gaseificação no setor sucroalcooleiro

In this work is studied the fluid dynamic characteristics of sugarcane bagasse for gasification applications and use of syngas in the sugarcane sector. This is an experimental work, which is initially performed the particle size separation of sugarcane bagasse particles, using appropriate equipment. Through the experiment is possible to determine the average diameter of particles pomace typical sugarcane mill. The equipment used for the grading sieve separation assembly consists of several dimensions, arranged vertically and which shows adequate for good separation from the pulp. Later, it makes immediate analysis for the determination of moisture, ash, volatile materials and fixed carbon. The study also determines the gross calorific value and allows analysis of densities of particles of sugar cane bagasse. Also studied the bagasse morphology using electron microscopes, where it was possible to visualize the geometry of the particles of bagasse. The use of Electronic Scanning Microscopy (SEM) provided better understand the morphology and particle size measured by using photography methods. Two methods for determining the sphericity of the particles were also used. The experiments carried out using appropriate standards and specific equations, allowing compare the present results with the values found by several researchers. Subsequently, fluid dynamic simulations were performed for the determination of porosity and minimum fluidization velocity theoretical. It follows that the sphericity and porosity of the bagasse particles influence the minimum fluidization velocity of biomass

Thermodynamic, Economic and Emissions Analysis of a Micro Gas Turbine Cogeneration System operating on Biofuels

Pós-graduação em Engenharia Mecânica - FEG

Partial oxidation of methane on NiO-MgO-ZrO2 catalysts

Catalysts containing mixtures of NiO, MgO and ZrO2 were synthesized by the polymerization method. They were characterized by X-ray diffraction (XRD), physisorption of N-2 (BET), X-ray photoelectron spectroscopy (XPS) and X-ray absorption near-edge structure (XANES), and then tested in the partial oxidation of methane (POM) in the presence of air (2CH(4):1O(2)) at 750 degrees C for 6 h. Among the ternary oxides, the catalyst with 40 mol% MgO showed the highest conversion rates in the catalytic processes, but also the highest carbon deposition values (48 mmol h (1)). The greater the amount of NiO-MgO solid solution formed, the higher was the conversion rate of reactants (CH4), peaking at 40 mol% of MgO. Catalysts with lower Ni content on the surface achieved a high rate of CH4 conversion into synthesis gas (H-2 + CO). The formation of more NiO-MgO solid solution seemed to inhibit the deactivation of Ni degrees during reaction. The values of the H-2/CO product ratio were generally found to be slightly lower than stoichiometric. (C) 2012 Elsevier Ltd. All rights reserved.

Biomass Gasification - Process analysis and dimensioning aspects for downdraft units and gas cleaning lines

In such territories where food production is mostly scattered in several small / medium size or even domestic farms, a lot of heterogeneous residues are produced yearly, since farmers usually carry out different activities in their properties. The amount and composition of farm residues, therefore, widely change during year, according to the single production process periodically achieved. Coupling high efficiency micro-cogeneration energy units with easy handling biomass conversion equipments, suitable to treat different materials, would provide many important advantages to the farmers and to the community as well, so that the increase in feedstock flexibility of gasification units is nowadays seen as a further paramount step towards their wide spreading in rural areas and as a real necessity for their utilization at small scale. Two main research topics were thought to be of main concern at this purpose, and they were therefore discussed in this work: the investigation of fuels properties impact on gasification process development and the technical feasibility of small scale gasification units integration with cogeneration systems. According to these two main aspects, the present work was thus divided in two main parts. The first one is focused on the biomass gasification process, that was investigated in its theoretical aspects and then analytically modelled in order to simulate thermo-chemical conversion of different biomass fuels, such as wood (park waste wood and softwood), wheat straw, sewage sludge and refuse derived fuels. The main idea is to correlate the results of reactor design procedures with the physical properties of biomasses and the corresponding working conditions of gasifiers (temperature profile, above all), in order to point out the main differences which prevent the use of the same conversion unit for different materials. At this scope, a gasification kinetic free model was initially developed in Excel sheets, considering different values of air to biomass ratio and the downdraft gasification technology as particular examined application. The differences in syngas production and working conditions (process temperatures, above all) among the considered fuels were tried to be connected to some biomass properties, such elementary composition, ash and water contents. The novelty of this analytical approach was the use of kinetic constants ratio in order to determine oxygen distribution among the different oxidation reactions (regarding volatile matter only) while equilibrium of water gas shift reaction was considered in gasification zone, by which the energy and mass balances involved in the process algorithm were linked together, as well. Moreover, the main advantage of this analytical tool is the easiness by which the input data corresponding to the particular biomass materials can be inserted into the model, so that a rapid evaluation on their own thermo-chemical conversion properties is possible to be obtained, mainly based on their chemical composition A good conformity of the model results with the other literature and experimental data was detected for almost all the considered materials (except for refuse derived fuels, because of their unfitting chemical composition with the model assumptions). Successively, a dimensioning procedure for open core downdraft gasifiers was set up, by the analysis on the fundamental thermo-physical and thermo-chemical mechanisms which are supposed to regulate the main solid conversion steps involved in the gasification process. Gasification units were schematically subdivided in four reaction zones, respectively corresponding to biomass heating, solids drying, pyrolysis and char gasification processes, and the time required for the full development of each of these steps was correlated to the kinetics rates (for pyrolysis and char gasification processes only) and to the heat and mass transfer phenomena from gas to solid phase. On the basis of this analysis and according to the kinetic free model results and biomass physical properties (particles size, above all) it was achieved that for all the considered materials char gasification step is kinetically limited and therefore temperature is the main working parameter controlling this step. Solids drying is mainly regulated by heat transfer from bulk gas to the inner layers of particles and the corresponding time especially depends on particle size. Biomass heating is almost totally achieved by the radiative heat transfer from the hot walls of reactor to the bed of material. For pyrolysis, instead, working temperature, particles size and the same nature of biomass (through its own pyrolysis heat) have all comparable weights on the process development, so that the corresponding time can be differently depending on one of these factors according to the particular fuel is gasified and the particular conditions are established inside the gasifier. The same analysis also led to the estimation of reaction zone volumes for each biomass fuel, so as a comparison among the dimensions of the differently fed gasification units was finally accomplished. Each biomass material showed a different volumes distribution, so that any dimensioned gasification unit does not seem to be suitable for more than one biomass species. Nevertheless, since reactors diameters were found out quite similar for all the examined materials, it could be envisaged to design a single units for all of them by adopting the largest diameter and by combining together the maximum heights of each reaction zone, as they were calculated for the different biomasses. A total height of gasifier as around 2400mm would be obtained in this case. Besides, by arranging air injecting nozzles at different levels along the reactor, gasification zone could be properly set up according to the particular material is in turn gasified. Finally, since gasification and pyrolysis times were found to considerably change according to even short temperature variations, it could be also envisaged to regulate air feeding rate for each gasified material (which process temperatures depend on), so as the available reactor volumes would be suitable for the complete development of solid conversion in each case, without even changing fluid dynamics behaviour of the unit as well as air/biomass ratio in noticeable measure. The second part of this work dealt with the gas cleaning systems to be adopted downstream the gasifiers in order to run high efficiency CHP units (i.e. internal engines and micro-turbines). Especially in the case multi–fuel gasifiers are assumed to be used, weightier gas cleaning lines need to be envisaged in order to reach the standard gas quality degree required to fuel cogeneration units. Indeed, as the more heterogeneous feed to the gasification unit, several contaminant species can simultaneously be present in the exit gas stream and, as a consequence, suitable gas cleaning systems have to be designed. In this work, an overall study on gas cleaning lines assessment is carried out. Differently from the other research efforts carried out in the same field, the main scope is to define general arrangements for gas cleaning lines suitable to remove several contaminants from the gas stream, independently on the feedstock material and the energy plant size The gas contaminant species taken into account in this analysis were: particulate, tars, sulphur (in H2S form), alkali metals, nitrogen (in NH3 form) and acid gases (in HCl form). For each of these species, alternative cleaning devices were designed according to three different plant sizes, respectively corresponding with 8Nm3/h, 125Nm3/h and 350Nm3/h gas flows. Their performances were examined on the basis of their optimal working conditions (efficiency, temperature and pressure drops, above all) and their own consumption of energy and materials. Successively, the designed units were combined together in different overall gas cleaning line arrangements, paths, by following some technical constraints which were mainly determined from the same performance analysis on the cleaning units and from the presumable synergic effects by contaminants on the right working of some of them (filters clogging, catalysts deactivation, etc.). One of the main issues to be stated in paths design accomplishment was the tars removal from the gas stream, preventing filters plugging and/or line pipes clogging At this scope, a catalytic tars cracking unit was envisaged as the only solution to be adopted, and, therefore, a catalytic material which is able to work at relatively low temperatures was chosen. Nevertheless, a rapid drop in tars cracking efficiency was also estimated for this same material, so that an high frequency of catalysts regeneration and a consequent relevant air consumption for this operation were calculated in all of the cases. Other difficulties had to be overcome in the abatement of alkali metals, which condense at temperatures lower than tars, but they also need to be removed in the first sections of gas cleaning line in order to avoid corrosion of materials. In this case a dry scrubber technology was envisaged, by using the same fine particles filter units and by choosing for them corrosion resistant materials, like ceramic ones. Besides these two solutions which seem to be unavoidable in gas cleaning line design, high temperature gas cleaning lines were not possible to be achieved for the two larger plant sizes, as well. Indeed, as the use of temperature control devices was precluded in the adopted design procedure, ammonia partial oxidation units (as the only considered methods for the abatement of ammonia at high temperature) were not suitable for the large scale units, because of the high increase of reactors temperature by the exothermic reactions involved in the process. In spite of these limitations, yet, overall arrangements for each considered plant size were finally designed, so that the possibility to clean the gas up to the required standard degree was technically demonstrated, even in the case several contaminants are simultaneously present in the gas stream. Moreover, all the possible paths defined for the different plant sizes were compared each others on the basis of some defined operational parameters, among which total pressure drops, total energy losses, number of units and secondary materials consumption. On the basis of this analysis, dry gas cleaning methods proved preferable to the ones including water scrubber technology in al of the cases, especially because of the high water consumption provided by water scrubber units in ammonia adsorption process. This result is yet connected to the possibility to use activated carbon units for ammonia removal and Nahcolite adsorber for chloride acid. The very high efficiency of this latter material is also remarkable. Finally, as an estimation of the overall energy loss pertaining the gas cleaning process, the total enthalpy losses estimated for the three plant sizes were compared with the respective gas streams energy contents, these latter obtained on the basis of low heating value of gas only. This overall study on gas cleaning systems is thus proposed as an analytical tool by which different gas cleaning line configurations can be evaluated, according to the particular practical application they are adopted for and the size of cogeneration unit they are connected to.

Sistemi Rh/CeO2-Al2O3 per l'ossidazione catalitica del metano

L’ossidazione catalitica parziale (CPO) del metano è un processo di elevato interesse scientifico ed industriale, permettendo la produzione su piccola scala di H2 o la produzione di syngas con un rapporto H2/CO = 2, utile per la produzione di metanolo o la sintesi di Fischer-Tropsch di idrocarburi. Inoltre, si possono raggiungere elevate conversioni del metano e selettività in syngas operando a bassi valori del tempo di contatto, riducendo così le dimensioni dei reattori. Tuttavia, gli elevati flussi e le temperature raggiunte nel letto possono condurre rapidamente alla disattivazione del catalizzatore; pertanto, è necessario lo sviluppo di materiali non soltanto attivi, ma anche stabili nelle condizioni di reazione. Lo scopo di questo lavoro è stato lo sviluppo di catalizzatori a base di Rh e ceria, utilizzati sia come pellets che supportati su una schiuma metallica. In particolare, il lavoro è stato focalizzato sulla sintesi, caratterizzazione ed attività catalitica di materiali Rh-CeO2-Al2O3. La presenza di CeO2 può modificare la dispersione del Rh metallico e la sua stabilità nei confronti della sinterizzazione e della formazione del carbone, mentre la stabilità termica è favorita dalla presenza di Al2O3. Poiché queste proprietà e, di conseguenza, le prestazione catalitiche dipendono dalla dimensioni delle particelle di CeO2 sono stati preparati catalizzatori con diverso contenuto di CeO2 (10 e 20 p/p %) ed utilizzando differenti metodi di preparazione per modularne le proprietà. Le sintesi sono effettuate per coprecipitazione e per sintesi con urea per trattamento micronde-idrotermale. Le prestazione dei catalizzatori in pellets sono state analizzate in un impianto di laboratorio operando a bassi valori del tempo di contatto e modificando la temperatura e la concentrazione della miscela gassosa, i.e. sia in condizioni lontane dall’equilibrio termodinamico che in condizioni prossime a quelle industriali. Un catalizzatore con lo stesso contenuto di Rh ed ottenuto da precursori tipo idrotalcite (HT) è stato utilizzato come riferimento. Per incrementare ulteriormente le prestazioni catalitiche, in particolare il trasferimento del calore lungo il letto catalitico, la migliore composizione individuata delle prove precedenti è stata depositata su pellets di una schiuma metallica (FeCrAlloy). E’ stato utilizzato il metodo dell’elettrosintesi per la deposizione di idrossidi di Rh, Ce e Al, ottenendo dopo calcinazione catalizzatori strutturati. Si è valutato l’effetto dei parametri di sintesi, potenziale applicato e tempo, sulle proprietà catalitiche. Anche in questo caso i risultati sono stati confrontati quelli ottenuti con un catalizzatori di riferimento ottenuti da un precursore HT preparati per elettrosintesi.

Impianto pilota per la pirolisi di PFU: ottimizzazione dei parametri di processo, studio e caratterizzazione dei prodotti ottenuti

In questo lavoro sono descritte le attività svolte a partire dal primo avviamento dell’impianto pilota di pirolisi di pneumatici, le ottimizzazioni impiantistiche e di processo effettuate, la caratterizzazione dei materiali di partenza e dei prodotti. Particolare attenzione è stata posta alla variabilità dei prodotti in uscita in funzione di parametri di processo quali operazioni preliminari, temperatura, pressione, quantità di materiale trattato e tempo di residenza, allo scopo di ottimizzare il processo e individuare le condizioni per l’ottenimento di specifici prodotti a livello quali- e quantitativo.

Ruolo della composizione e metodo di preparazione nelle proprietà di catalizzatori contenenti cerio per l'ossidazione parziale catalitica del metano

Questo a lavoro di tesi si è incentrato sullo sviluppo di catalizzatori attivi nella reazione di ossidazione parziale catalitica (CPO) del metano per la produzione di idrogeno o/e syngas, con un rapporto ottimale di H2/CO, utile per la produzione idrocarburi attraverso la reazione di Fischer-Tropsch o per l’alimentazione delle fuels cells. La scarsa diffusione di questo processo è da attribuirsi alla mancanza di catalizzatori adatti a resistere agli elevati flussi e alle elevate temperature raggiunte nel letto senza subire processi di disattivazione; pertanto, è necessario lo sviluppo di nuovi catalizzatori non soltanto attivi, ma anche stabili nelle condizioni di reazione. In questa tesi si sono studiati catalizzatori con differenti fasi attive Rh e Ru supportati su CeO2-Al2O3, utilizzati in pellets. L'attenzione di questo lavoro di tesi si è focalizzata sullo studio delle proprietà e del ruolo della fase attiva e del promotore ceria nei catalizzatori. Per questo studio sono stati sintetizzati per coprecipitazione due catalizzatori con ugual concentrazione di cerio ma diversa fase attiva, Rodio e Rutenio e se ne sono studiate le proprietà. Della fase attiva con migliori prestazioni, il Rh, se ne è approfondito lo studio, indagando sulla migliore metodologia di attivazione e sul miglior metodo di sintesi del catalizzatore. Infine, per lo studio dell’effetto del cerio sia nelle proprietà chimico-fisiche che nella attività catalitica, sono stati preparati per coprecipitazione diversi catalizzatori di tipo Rh-CeO2-Al2O3, con un contenuto di cerio variabile ma con ugual concentrazione di fase attiva, cosi come dei campioni di riferimento contenti soltanto ceria o allumina. Questi catalizzatori sono stati testati in severe condizioni e per lunghi tempi di reazione per simulare l’utilizzo industriale ed evidenziarne le caratteristiche.

Catalysts and processes for next-generation H2 production

The present study is focused on the development of new VIII group metal on CeO2 – ZrO2 (CZO) catalyst to be used in reforming reaction for syngas production. The catalyst are tested in the oxyreforming process, extensively studied by Barbera [44] in a new multistep process configuration, with intermediate H2 membrane separation, that can be carried out at lower temperature (750°C) with respect the reforming processes (900 – 1000°C). In spite of the milder temperatures, the oxy-reforming conditions (S/C = 0.7; O2/C = 0.21) remain critical regarding the deactivation problems mainly deriving from thermal sintering and carbon formation phenomena. The combination of the high thermal stability characterizing the ZrO2, with the CeO2 redox properties, allows the formation of stable mixed oxide system with high oxygen mobility. This feature can be exploited in order to contrast the carbon deposition on the active metal surface through the oxidation of the carbon by means of the mobile oxygen atoms available at the surface of the CZO support. Ce0.5Zr0.5O2 is the phase claimed to have the highest oxygen mobility but its formation is difficult through classical synthesis (co-precipitation), hence a water-in-oil microemulsion method is, widely studied and characterized. Two methods (IWI and bulk) for the insertion of the active metal (Rh, Ru, Ni) are followed and their effects, mainly related to the metal stability and dispersion on the support, are discussed, correlating the characterization with the catalytic activity. Different parameters (calcination and reduction temperatures) are tuned to obtain the best catalytic system both in terms of activity and stability. Interesting results are obtained with impregnated and bulk catalysts, the latter representing a new class of catalysts. The best catalysts are also tested in a low temperature (350 – 500°C) steam reforming process and preliminary tests with H2 membrane separation have been also carried out.

Biogas and bio-hydrogen: production and uses. A review

The first part of this essay aims at investigating the already available and promising technologies for the biogas and bio-hydrogen production from anaerobic digestion of different organic substrates. One strives to show all the peculiarities of this complicate process, such as continuity, number of stages, moisture, biomass preservation and rate of feeding. The main outcome of this part is the awareness of the huge amount of reactor configurations, each of which suitable for a few types of substrate and circumstance. Among the most remarkable results, one may consider first of all the wet continuous stirred tank reactors (CSTR), right to face the high waste production rate in urbanised and industrialised areas. Then, there is the up-flow anaerobic sludge blanket reactor (UASB), aimed at the biomass preservation in case of highly heterogeneous feedstock, which can also be treated in a wise co-digestion scheme. On the other hand, smaller and scattered rural realities can be served by either wet low-rate digesters for homogeneous agricultural by-products (e.g. fixed-dome) or the cheap dry batch reactors for lignocellulose waste and energy crops (e.g. hybrid batch-UASB). The biological and technical aspects raised during the first chapters are later supported with bibliographic research on the important and multifarious large-scale applications the products of the anaerobic digestion may have. After the upgrading techniques, particular care was devoted to their importance as biofuels, highlighting a further and more flexible solution consisting in the reforming to syngas. Then, one shows the electricity generation and the associated heat conversion, stressing on the high potential of fuel cells (FC) as electricity converters. Last but not least, both the use as vehicle fuel and the injection into the gas pipes are considered as promising applications. The consideration of the still important issues of the bio-hydrogen management (e.g. storage and delivery) may lead to the conclusion that it would be far more challenging to implement than bio-methane, which can potentially “inherit” the assets of the similar fossil natural gas. Thanks to the gathered knowledge, one devotes a chapter to the energetic and financial study of a hybrid power system supplied by biogas and made of different pieces of equipment (natural gas thermocatalitic unit, molten carbonate fuel cell and combined-cycle gas turbine structure). A parallel analysis on a bio-methane-fed CCGT system is carried out in order to compare the two solutions. Both studies show that the apparent inconvenience of the hybrid system actually emphasises the importance of extending the computations to a broader reality, i.e. the upstream processes for the biofuel production and the environmental/social drawbacks due to fossil-derived emissions. Thanks to this “boundary widening”, one can realise the hidden benefits of the hybrid over the CCGT system.

Sviluppo di un sistema integrato innovativo per la contemporanea produzione e separazione di H2 ultrapuro, attraverso oxy-reforming, water-gas shift e membrane al Pd

Il presente lavoro di tesi si è focalizzato sullo studio e sulla ottimizzazione di un sistema integrato, che utilizzi la reazione di oxy-reforming del metano al fine di produrre syngas che venga trattato attraverso la water-gas shift al fine di abbattere il contenuto di CO e al tempo stesso aumentare la resa in H2. Con l’obiettivo di ottenere H2 ad elevata purezza (>99%) da poter essere inviato direttamente a celle a combustible ed in impianti di piccola taglia con possibile delocalizzazione della produzione industriale di energia elettrica e termica “pulita”, la miscela reale uscente dal processo di oxy-reforming è stata processata tramite successiva water-gas shift direttamente all’interno di una membrana ceramica al Pd selettiva nella separazione di H2. L’innovativià di questo progetto di studio è data da diversi parametri quali: 1) l’impiego dell’oxy-reforming in alternativa al normale steam-reforming del CH4, che permette di condurre il processo a temperature decisamente inferiori (700-750°C), utilizzando un minor quantitativo di vapore (S/C = 0.7); 2) l’utilizzo di due nuove formulazioni di catalizzatore di WGS per alte temperature, capace di operare in un unico stadio conversioni di CO ottenibili industrialmente solo attraverso i convenzionali due due stadi di reazione (e due diverse formulazioni di catalizzatori a base di Fe/Cr e Cu); 3) l’utilizzo di supporti ceramici con membrana a base di Pd, capaci di ospitare al loro interno un catalizzatore eterogeneo per la reazione di WGS a 400°C, rendendo quindi possibile la produzione e contemporanea separazione di H2 con un ulteriore effetto positivo poiché la membrana rimuovendo H2 dalla zona di reazione favorisce il superamento dell’equilibrio termodinamico per la conversione del CO, abbassandone il contenuto nel flusso uscente dei gas reazione e rendendo non più necessari sistemi aggiuntivi di separazione quali PSA o PROXY.

Sviluppo di un gassificatore downdraft da 20kWe e analisi dei prodotti

L’elaborato affronta i temi dello sviluppo sostenibile, dell’affrancamento dalle risorse fossili e della produzione di energetica capillare. Nell’ambito di un progetto di ricerca mirato allo sviluppo di un gassificatore downdraft di tipo Imbert da 20kWe alimentato a legno cippato, viene qui presentato l’avviamento della campagna sperimentale su un impianto pilota. Particolare attenzione viene rivolta alla biomassa e ai prodotti di gassificazione (char, tar e syngas), le cui caratterizzazioni hanno contribuito all’evoluzione impiantistica e protocollare, interamente descritte nel testo.

Micro combined heat and power laboratory development

Micro Combined Heat and Power (Micro-CHP) system produces both electricity and heat required for residential or small business applications. Use of Micro-CHP in a residential application not only creates energy and economic savings but also reduces the carbon foot print of the house or small business. Additionally, micro-CHP can subsidize its cost of operation by selling excess electricity produced back to the grid. Even though Micro-CHP remains attractive on paper, high initial cost and optimization issues in residential scale heat and electrical requirement has kept this technology from becoming a success. To understand and overcome all disadvantages posed my Micro-CHP system, a laboratory is developed to test different scenarios of Micro-CHP applications so that we can learn and improve the current technology. This report focuses on the development of this Micro-CHP laboratory including installation of Ecopower micro-CHP unit, developing fuel line and exhaust line for Ecopower unit, design of electrical and thermal loop, installing all the instrumentation required for data collection on the Ecopower unit and developing controls for heat load simulation using thermal loop. Also a simulation of Micro-CHP running on Syngas is done in Matlab. This work was supported through the donation of ‘Ecopower’ a Micro-CHP unit by Marathon Engine and through the support of Michigan Tech REF-IF grand.

Analysis of the Behaviour of Biofuel-Fired Gas Turbine Power Plants

The utilisation of biofuels in gas turbines is a promising alternative to fossil fuels for power generation. It would lead to significant reduction of CO2 emissions using an existing combustion technology, although significant changes seem to be needed and further technological development is necessary. The goal of this work is to perform energy and exergy analyses of the behaviour of gas turbines fired with biogas, ethanol and synthesis gas (bio-syngas), compared with natural gas. The global energy transformation process (i.e. from biomass to electricity) has also been studied. Furthermore, the potential reduction of CO2 emissions attained by the use of biofuels has been determined, considering the restrictions regarding biomass availability. Two different simulation tools have been used to accomplish the aims of this work. The results suggest a high interest and the technical viability of the use of Biomass Integrated Gasification Combined Cycle (BIGCC) systems for large scale power generation.

Estudio energético comparativo de diferentes configuraciones de ciclo combinado

El objetivo del presente proyecto consiste en la modelización y optimización de una planta de gasificación integrada en ciclo combinado de 400 MW de potencia neta, mediante el uso del programa Cycle-Tempo, desarrollado por la Universidad de Delft. Para la modelización de la planta, se ha dividido en sus dos unidades principales: la isla de gasificación y el ciclo combinado. Para la validación del modelo de la isla de gasificación, se ha utilizado una composición de referencia de un combustible gasificable y se ha obtenido la composición del gas de síntesis esperada. Se han modelado y optimizado varias configuraciones de ciclo combinado, variando los parámetros característicos de la caldera de recuperación de calor. Se ha realizado la integración de las dos unidades para maximizar la potencia entregada por la planta. Finalmente, se ha estimado el balance anual de energía del ciclo combinado alimentado con gas natural y con el gas de síntesis, con el fin de comparar las rentabilidades económicas obtenidas. Mediante el estudio realizado, se deduce que la forma más eficiente de producir energía, a partir del uso del carbón, es la tecnología de gasificación integrada en ciclo combinado, pese a que su rendimiento sea inferior al ciclo combinado alimentado con gas natural. ABSTRACT The aim of this project is the modeling and optimization of an integrated gasification combined cycle plant of 400 MW net power, using the Cycle-Tempo program, developed by the University of Delft. For the modeling of the plant, it has been divided into its two main units: the island of gasification and the combined cycle. For the model validation of the gasification island, a reference composition of a gasifiable fuel has been used and the expected synthesis gas composition was obtained. Several configurations of combined cycle have been modeled and optimized by varying the characteristic parameters of the heat recovery steam generator. It has made the integration of the two units to reach maximum optimization of power, which has been delivered by the plant. Finally, it has been estimated the annual energy balance for the combined cycle plant fueled with natural gas and with syngas, in order to compare the profitability obtained with each one. Through the study, it is deduced that the most efficient way to produce energy from the use of coal, is the integrated gasification combined cycle technology, although their performance is lower than that obtained from the combined cycle fueled with natural gas.