Interference in transport through double barriers in interacting quantum wires

We investigate interference effects of the backscattering current through a double-barrier structure in an interacting quantum wire attached to noninteracting leads. Depending on the interaction strength and the location of the barriers, the backscattering current exhibits different oscillation and scaling characteristics with the applied voltage in the strong and weak interaction cases. However, in both cases, the oscillation behaviors of the backscattering current are mainly determined by the quantum mechanical interference due to the existence of the double barriers.

Paired interference 3-dB coupler based on SOI rib waveguides with anisotropic chemical wet etching

A 3-dB paired interference (PI) optical coupler in silicon-on-insulator (SOI) based on rib waveguides with trapezoidal cross section was designed with simulation by a modified finite-difference beam propagation method (FD-BPM) and fabricated by potassium hydroxide (KOH) anisotropic chemical wet etching. Theoretically, tolerances of width, length, and port distance are more than 1, 100, and 1 mu m, respectively. Smooth interface was obtained with the propagation loss of 1.1 dB/cm at the wavelength of 1.55 mu m. The coupler has a good uniformity of 0.2 dB and low excess loss of less than 2 dB.

Coulomb blockade double-dot Aharonov-Bohm interferometer: Harmonic decomposition of the interference pattern

For the solid-state double-dot interferometer, the phase shifted interference pattern induced by the interplay of inter-dot Coulomb correlation and multiple reflections is analyzed by harmonic decomposition. Unexpected result is uncovered, and is discussed in connection with the which-path detection and electron loss. (C) 2009 Elsevier B.V. All rights reserved.

New type of multimode-interference-type thermo-optic variable optical attenuator

A thermo-optic variable optical attenuator (VOA) based on a Mach-Zehnder interferometer and multimode-interference coupler is fabricated. Not a single-mode but a multimode waveguide is used as the input and output structures of the optical field, which greatly reduces the coupling loss of the VOA with a normal single-mode fiber. The insertion loss of the fabricated VOA is 2.52 to 2.82 dB at the wavelength of 1520 to 1570 nm. The polarization dependent loss is 0.28 to 0.45 dB at the same wavelength range. Its maximum attenuation range is up to 26.3 dB when its power consumption is 369 mW. The response frequency of the fabricated VOA is about 10 kHz. (C) 2004 Society of Photo-Optical Instrumentation Engineers.

Study on the internal reflection of the multimode-interference-type device

The internal reflection of the multimode-interference (MMI)-type device is calculated with the bidirectional beam propagation method. The calculated results indicate that the difference of the effective refractive indices between the core region and the surrounding region has a determining effect on the internal reflection of the MMI-type device. The output taper for the MMI-type combiner and splitter has a more evident effect on the internal reflection than the input taper. The internal reflection decreases with increasing the end width of the taper. For the MMI-type device with appropriate tapers, the internal reflection does not show evident degradation with the deviation of the length of the MMI region from its optimal value. (C) 2004 Society of Photo-Optical Instrumentation Engineers.

1x8 cascaded multimode interference splitter in silicon-on-insulator

A cascaded multimode interference 1 x 8 power splitter is proposed and fabricated in silicon-on-insulator material. The device consists of seven 1 x 2 power splitters arranged in a tree configuration. The cascaded splitter and its 1 x 2 splitter element have the power uniformity of approximately 1.5 dB and 0.3 dB, respectively.

Multimode interference 3-dB coupler in silicon-on-insulator based on silicon rib waveguides with trapezoidal cross section

A 3-dB multimode interference optical coupler based on rib waveguides with trapezoidal cross section was designed and fabricated on silicon-on-insulator wafer. Potassium hydroxide (KOH) anisotropic chemical etching of silicon was used to fabricate the waveguides to obtain smooth interface. A modified finite-difference beam propagation method was used to simulate the multimode rib waveguide with slope interfaces. The rms roughness of etching interface is as small as 1.49 nm. The propagation loss of the waveguide is 1.3 dB/cm at wavelength of 1.55 mum. The fabricated 3-dB coupler has a good uniformity of 0.2 dB.

Interference and non-interference of sidebands in a quantum dot with oscillating levels

When a quantum dot is suffering an AC gate voltage, the sidebands turn up beside the static levels of the dot. We formularized the conductance and current when the effective coupling between levels in the quantum dot induced by the hybrid terms is included using a bi-unitary transform method, and we investigated the interference of the photon sidebands of deferent levels. The interference occurs if the same sidebands of deferent levels overlap, which is possible only when the static levels lie close to and overlap with each other. The overlap of different photon sidebands leads to a simple non-coherent superposition. (C) 2005 Elsevier Ltd. All rights reserved.

Size tolerance analysis of a 4X4 tapered multimode interference coupler in a silicon-on-insulator structure

Size tolerance of a 4X4 general interference tapered multimode interference (MMI) coupler in a silicon-on-insulator (SOI) structure is investigated by means of a 2-D finite difference beam propagation method (2D-FDBPM), together with an effective refractive index method (EIM). The results show that the tapered multimode interference coupler exhibits relatively larger size tolerance when light is launched from the edgeport than from midport, though it has much better output power uniformity when light is launched from midport. Besides that, it can reduce the device length greatly. The 4X4 general interference tapered MMI coupler has a slightly larger size tolerance compared with a conventional straight multimode interference coupler. (C) 2003 Society of Photo-Optical Instrumentation Engineers.

Multimode-interference-type thermo-optic variable optical attenuator with a response frequency of 10 kHz

A thermo-optic variable optical attenuator based on a multimode interference coupler principle is fabricated. The propagation loss of the fabricated device is 1.6 to 3.8 dB at the wavelength range 1510 to 1610 nm, which is very near the calculated value (1.2 dB) by the finite difference beam propagation method. The maximum power consumption is 363 mW and the dynamic attenuation range is 0 to 26 dB. The response frequency of the fabricated attenuator is about 10 kHz. (C) 2003 Society of Photo-Optical Instrumentation Engineers.

Simulation and fabrication of thermo-optic variable optical attenuators based on multimode interference coupler

A type of thermo-optic variable optical attenuator based on multimode interference coupler is proposed. The optical field propagation properties of the devices are simulated using finite difference beam propagation method. The propagation loss of the fabricated device is 2-4.2 dB at the wavelength range 1510-1610 nm. The total power consumption is 370 mW and the maximum attenuation is more than 25 dB, which almost can meet the requirements of optical fiber communication systems.

Theory and experiment of two-photon 'direct' interference for type-II spontaneous parametric down-conversion with an ultrafast pulse laser pump

Fourth-order spatial interference of entangled photon pairs generated in the process of spontaneous parametric down-conversion pumped by a femtosecond pulse laser has been performed for the first time. In theory, it takes into account the transverse correlation between the two photons and is used to calculate the dependence of the visibility of the interference pattern obtained in Young's double-slit experiment. In this experiment, a short focal length tens and two narrow band interference filters were adopted to eliminate the effects of the broadband pump laser and improve the visibility of the interference pattern under the condition of nearly collinear light and degenerate phase matching.

Spatial interference effect of two-photon in femtosecond-pulse pumped spontaneous parametric down-conversion

We have used the transverse correlated properties of the entangled photon pairs generated in the process of spontaneous parametric down-conversion, which is pumped by a femtosecond pulse laser, to perform Young's interference experiment. Unlike the case of a continuous wave laser pump, a broadband pulse laser pump can submerge an interference pattern. In order to obtain a high visibility interference pattern, we used a lens with a tunable focal length and two interference filters to eliminate the effects of the broadband pump laser. It is proven that the process of two-photon direct interference is a post-selection process.

Compact 3-dB tapered multimode interference coupler in silicon-on-insulator

We have fabricated a compact 3-dB multimode interference coupler with a large silicon-on-insulator cross section. To reduce the length of the usual symmetric interference multimode interference coupler, we propose using a parabolically tapered structure. The length of the device is 398 mum. The device has a uniformity of 0.28 dB. (C) 2001 Optical Society of America.

Signal bandwidth of general N x N multimode interference couplers

Analytical expression of signal bandwidth of general straight and tapered N x N multimode interference (MMI) couplers is presented. The signal bandwidth is characterized as a function of mode relative energy, mode propagation delay time, and mode pulse broadening in the multimode section of MMI coupler. The model is used to evaluate the signal bandwidth of specific couplers. Results indicate that the signal bandwidth decreases seriously with the increase of channel number and channel guide space. Compared with the straight MMI coupler, the tapered MMI coupler has an improved signal bandwidth.