Cancellation of residual ghost VSB components from video IIR deghoster systems

Certain deghosters suffer from the presence of distortion caused by the quadrature forming nature of the IF VSB filter operating on a ghosted IF signal. By analysing this a priori effect, a specific deghoster solution is found by using the phase quadrature detected IF signal to cancel the VSB induced ghost quadrature distortions from the detected inphase signal before deghosting takes place.

Preventing carbon contamination of optical devices for X-rays: the effect of oxygen on photon-induced dissociation of CO on platinum

Platinum is one of the most common coatings used to optimize mirror reflectivity in soft X-ray beamlines. Normal operation results in optics contamination by carbon-based molecules present in the residual vacuum of the beamlines. The reflectivity reduction induced by a carbon layer at the mirror surface is a major problem in synchrotron radiation sources. A time-dependent photoelectron spectroscopy study of the chemical reactions which take place at the Pt(111) surface under operating conditions is presented. It is shown that the carbon contamination layer growth can be stopped and reversed by low partial pressures of oxygen for optics operated in intense photon beams at liquidnitrogen temperature. For mirrors operated at room temperature the carbon contamination observed for equivalent partial pressures of CO is reduced and the effects of oxygen are observed on a long time scale.

Effect of impurities in biodiesel-derived waste glycerol on the performance and feasibility of biotechnological processes

The rapid development of biodiesel production technology has led to the generation of tremendous quantities of glycerol wastes, as the main by-product of the process. Stoichiometrically, it has been calculated that for every 100 kg of biodiesel, 10 kg of glycerol are produced. Based on the technology imposed by various biodiesel plants, glycerol wastes may contain numerous kinds of impurities such as methanol, salts, soaps, heavy metals and residual fatty acids. This fact often renders biodiesel-derived glycerol unprofitable for further purification. Therefore, the utilization of crude glycerol though biotechnological means represents a promising alternative for the effective management of this industrial waste. This review summarizes the effect of various impurities-contaminants that are found in biodiesel-derived crude glycerol upon its conversion by microbial strains in biotechnological processes. Insights are given concerning the technologies that are currently applied in biodiesel production, with emphasis to the impurities that are added in the composition of crude glycerol, through each step of the production process. Moreover, extensive discussion is made in relation with the impact of the nature of impurities upon the performances of prokaryotic and eukaryotic microorganisms, during crude glycerol bioconversions into a variety of high added-value metabolic products. Finally, aspects concerning ways of crude glycerol treatment for the removal of inhibitory contaminants as reported in the literature are given and comprehensively discussed

Recovery and upgrading bovine rumen protein by extrusion: Effect of lipid content on protein disulphide cross-linking, solubility and molecular weight

Bovine rumen protein with two levels of residual lipids (1.9% or 3.8%) was subjected to thermoplastic extrusion under different temperatures and moisture contents. Protein Solubility in different buffers, disulphide cross-linking and molecular weight distribution were determined on the extrudates. After extrusion, samples with 1.9% residual lipids content had a higher concentration of protein insoluble by undetermined forces, irrespective of feed moisture and processing temperature used. Lipid content of 3.8% in the feed material resulted in more protein participating in the extrudate network through non-covalent interactions (hydrophobic and electrostatic) and disulphide bonds. A small dependency of the extrusion process on moisture and temperature and a marked dependency on lipid content, especially phospholipid, was observed, Electrophoresis under non-reducing conditions showed that protein extrusion with low feed moisture promoted high molecular breakdown inside the barrel, probably due to intense shear force, and further protein aggregation at the die end. (C) 2009 Elsevier Ltd. All rights reserved.

Effect of enzymatic pretreatment and increasing the organic loading rate of lipid-rich wastewater treated in a hybrid UASB reactor

This study aimed at evaluating the effect of increasing organic loading rates and of enzyme pretreatment on the stability and efficiency of a hybrid upflow anaerobic sludge blanket reactor (UASBh) treating dairy effluent. The UASBh was submitted to the following average organic loading rates (OLR) 0.98 Kg.m(-3).d(-1), 4.58 Kg.m(-3).d(-1), 8.89 Kg.m(-3).d(-1) and 15.73 Kg.m(-3).d(-1), and with the higher value, the reactor was fed with effluent with and without an enzymatic pretreatment to hydrolyze fats. The hydraulic detention time was 24 h, and the temperature was 30 +/- 2 degrees C. The reactor was equipped with a superior foam bed and showed good efficiency and stability until an OLR of 8.89 Kg.m(-3).d(-1). The foam bed was efficient for solid retention and residual volatile acid concentration consumption. The enzymatic pretreatment did not contribute to the process stability, propitiating loss in both biomass and system efficiency. Specific methanogenic activity tests indicated the presence of inhibition after the sludge had been submitted to the pretreated effluent It was concluded that continuous exposure to the hydrolysis products or to the enzyme caused a dramatic drop in the efficiency and stability of the process, and the single exposure of the biomass to this condition did not inhibit methane formation. (C) 2011 Elsevier B.V. All rights reserved.

The Sphene-Centered Ocellar Texture: An Effect of Grain-Supported Flow and Melt Migration in a Hyperdense Magma Mush

The sphene-centered ocellar texture consists of leucocratic ocelli with sphene (titanite) crystals at the center, enclosed in a biotite-rich matrix. This texture has been recognized worldwide in hybrid intermediate rocks. On the basis of structural, petrological, and geochronological data from selected outcrops of the Variscan Ribadelago pluton (NW Iberian Massif), we propose that the ocelli were formed by migration and accumulation of a residual melt through a plagioclase- and biotite-dominated crystalline framework. At the late stage of crystallization, the magma acted as a hyperdense suspension and reacted to the pressure gradient caused by the regional stress field, entering the domain of grain-supported flow. Microstructures reveal that aligned crystal domains arose in the crystal framework from the shearing and compaction of the crystal mush and behaved as magmatic microshears. Relative displacement of adjacent crystal clusters along these microshears corresponded to the onset of Reynolds dilatancy that generated an expansion of the crystal mush, involving melt migration and pore aperture. The mineralogy of the ocelli, dominated by andesine and sphene, represents the composition of the migrating melt. The chemistry of this late, Ti-rich melt stems from the incongruent melting of biotite. Magmatic sphene from the ocelli yields a U-Pb age of 317 +/- 1 Ma, which represents the final crystallization of the hybridized magmatic system. Moreover, this texture offers an opportunity to better understand the rheological behavior of highly crystallized magmas.

Genetic Control of Residual Variance for Teat Number in Pigs

The genetic improvement in litter size in pigs has been substantial during the last 10-15 years. The number of teats on the sow must increase as well to meet the needs of the piglets, because each piglet needs access to its own teat. We applied a genetic heterogeneity model on teat numberin sows, and estimated medium-high heritability for teat number (0.5), but low heritability for residual variance (0.05), indicating that selection for reduced variance might have very limited effect. A numerically positive correlation (0.8) between additive genetic breeding values for mean and for variance was found, but because of the low heritability for residual variance, the variance will increase very slowly with the mean.

The Effect of Residence Time on the Tensile Properties of Superelastic and Thermal Activated Ni-Ti Orthodontic Wires

Since the 1980s, different devices based on superelastic alloys have been developed to fulfill orthodontic applications. Particularly in the last decades several researches have been carried out to evaluate the mechanical behavior of Ni-Ti alloys, including their tensile, torsion and fatigue properties. However, studies regarding the dependence of elastic properties on residence time of Ni-Ti wires in the oral cavity are scarce. Such approach is essential since metallic alloys are submitted to mechanical stresses during orthodontic treatment as well as pH and temperature fluctuations. The goal of the present contribution is to provide elastic stress-strain results to guide the orthodontic choice between martensitic thermal activated and austenitic superelastic Ni-Ti alloys. From the point of view of an orthodontist, the selection of appropriate materials and the correct maintenance of the orthodontic apparatus are essential needs during clinical treatment. The present work evaluated the elastic behavior of Ni-Ti alloy wires with diameters varying from 0.014 to 0.020 inches, submitted to hysteresis tensile tests with 8% strain. Tensile tests were performed after periods of use of 1, 2 and 3 months in the oral cavity of patients submitted to orthodontic treatment. The results from the hysteresis tests allowed to exam the strain range covered by isostress lines upon loading and unloading, as well as the residual strain after unloading for both superelastic and thermal activated Ni-Ti wires. Superelastic Ni-Ti wires exhibited higher load isostress values compared to thermal activated wires. It was found that such differences in the load isostress values can increase with increasing residence time.

Toxicidade residual de alguns agrotóxicos recomendado na agricultura sobre Neoseiulus californicus (McGregor) (Acari: Phytoseiidae)

O objetivo do trabalho foi avaliar a toxicidade residual de alguns agrotóxicos utilizados em citros sobre Neoseiulus californicus (McGregor) em condições de laboratório. O método de bioensaio adotado foi o de contato residual. Folhas de citros da variedade Pêra, acondicionadas em arenas, foram pulverizadas em torre de Potter. A toxicidade residual dos produtos foi avaliada duas horas e 1; 3; 5; 7; 10; 14 e 21 dias após a aplicação. em cada arena, foram transferidas dez fêmeas adultas de N. californicus, juntamente com uma quantidade suficiente de Tetranychus urticae, como fonte de alimento. As avaliações de mortalidade foram realizadas 72 horas após a transferência dos ácaros para as arenas. Os agrotóxicos acrinathrin, deltamethrin, dinocap, enxofre, fenpropathrin, óxido de fenbutatin e propargite não causaram mortalidades significativas em adultos de N. californicus. Foram registradas mortalidades de 29,8; 24,0 e 34,1% para ácaros N. californicus expostos a resíduos de duas horas de idade de abamectim, azocyclotin e cyhexatin, respectivamente. Dicofol, pyridaben e chlorfenapyr causaram 100% de mortalidade aos ácaros predadores expostos aos resíduos tóxicos dos acaricidas, com duas horas de idade. Abamectin provocou mortalidade significativa por um período inferior a um dia. Resíduos dos acaricidas azocyclotin, cyhexatin, dicofol, pyridaben e chlorfenapyr provocaram mortalidades significativas por períodos de 1; 1; 10; 10 e 21dias, respectivamente. Os resultados obtidos no presente experimento servem de subsídio para a escolha adequada dos agrotóxicos a serem utilizados em pomares de citros nos quais N. californicus esteja presente ou naqueles em que o predador venha a ser liberado. Esses resultados também servem para a escolha do momento mais favorável para a liberação dos ácaros predadores dessa espécie no campo, após a aplicação de agrotóxicos nos pomares. Estudos conduzidos em condições de campo ainda são necessários para se compreender melhor o efeito desses agrotóxicos sobre o ácaro predador.

Lead distribution in organic matter of loamy oxisol treated with manure and its effect on microbial biomass

This paper reports a study regarding the distribution of lead in the organic matter fractions of a loamy oxisol treated with stable manure, and its effect on the soil microbial biomass. The experimental design was a completely randomized factorial with three replicates. Treatments were four lead (Pb) rates (0, 200, 400, and 600 mg kg(-1) soil), two levels of manure (0 and 30 Mg ha(-1)) and two sampling times (30 and 60 days after lead application). Total and soil lead soluble in Mehlich 1 extractant, and Ph in the different fractions of the organic matter (fulvic acid, humic acid, and residual) were evaluated along with the soil microbial biomass. Data showed that lead, applied as PbCl2, was concentrated in the residual fraction. The application of manure at the rate of 30 Mg ha(-1) did not affect lead distribution in the fractions until 60 days after incorporation. Lead extracted by Mehlich 1 increased as function of the quantity applied. Manure stimulated the growth of the soil microbial biomass which was reduced by the 200 mg kg(-1) doses of lead, with manure application, increasing, however, with larger rates. Mehlich 1 extracted only part of the lead present in the residual fraction.

Efeitos da Heterogeneidade de Variância Residual entre Grupos de Contemporâneos na Avaliação Genética de Bovinos de Corte

O objetivo deste estudo foi investigar, por meio de dados simulados, o efeito da heterogeneidade de variância residual entre grupos de contemporâneos (GC) sobre as avaliações genéticas de bovinos de corte, e comparar o uso de uma avaliação genética ponderada (R¹Isigmae²) em relação à avaliação que pressupõe homogeneidade de variância (R=Isigmae²). A característica estudada foi ganho de peso pós-desmame corrigido para 345 dias, sendo esta simulada com variância fenotípica de 300 kg² e herdabilidade igual a 0,4. A estrutura de um conjunto real de dados foi utilizada para fornecer os GC e os pais referentes às observações de cada animal. Cinco níveis de heterogeneidade de variância residual foram considerados de forma que os componentes de variância fossem, na média, iguais aos da situação de homogeneidade de variância. Na medida em que níveis mais acentuados de heterogeneidade de variância residual foram considerados, os animais foram selecionados dos GC com maior variabilidade, especialmente com pressão de seleção intensa. em relação à consistência de predição, os produtos e as vacas tiveram seus valores genéticos preditos mais afetados pela heterogeneidade de variância residual do que os touros. O fator de ponderação utilizado reduziu, mas não eliminou o efeito da heterogeneidade de variância. As avaliações genéticas ponderadas apresentaram resultados iguais ou superiores àqueles obtidos pelas avaliações que assumiram homogeneidade de variância. Mesmo quando não necessário, o uso de avaliações ponderadas produziu resultados não inferiores às avaliações que assumiram homogeneidade de variância.

Genetic and environmental heterogeneity of residual variance of weight traits in Nellore beef cattle

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of pregnancy on the genetic evaluation of dairy cattle

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Potassium Leaching as Affected by Soil Texture and Residual Fertilization in Tropical Soils

Potassium (K) leaching is affected by soil texture and available K, among other factors. In this experiment, effects of soil texture and K availability on K distribution were studied in the presence of roots, with no excess water. Soils from two 6-year field experiments on a sandy clay loam and a clay soil fertilized yearly with 0, 60, 120, and 180 kg ha-1 of K2O were accommodated in pots that received 90 kg ha-1 of K2O. Soybean was grown up to its full bloom (R2). Under field conditions, K leaching below the arable layer increased with K rates, but the effect was less noticeable in the clay soil. Potassium leaching in a sandy clay loam soil was related to soil K contents from prior fertilizations. With no excess water, in the presence of soybean roots, K distribution in the profile was significant in the lighter textured soil but was not apparent on the heavier textured soil.

Métodos de determinação de cálcio e magnésio trocáveis e estimativa do calcário residual em um Latossolo submetido à aplicação de calcário e gesso em superfície

A determinação da fração do calcário remanescente no solo (calcário residual), em área onde foi realizada aplicação de calcário em superfície, sem incorporação, na implantação do sistema plantio direto, pode ser uma ferramenta importante para auxiliar na definição do momento em que se faz necessária a reaplicação de calcário. Nesse sentido, os objetivos deste trabalho foram avaliar: quais os teores de Ca e Mg trocáveis, extraídos por percolação com solução de KCl e resina trocadora de íons; a quantidade do calcário aplicado que ainda não havia reagido no solo, mediante a determinação dos teores de Ca e Mg não-trocáveis; e qual a influência do gesso nos teores de Ca e Mg trocáveis e na dissolução do calcário, 18 meses após a aplicação em superfície. O experimento foi realizado em um Latossolo Vermelho distroférrico, em Botucatu (SP). O delineamento experimental foi de blocos casualizados com parcelas subdivididas e quatro repetições. Nas parcelas, foram aplicadas quatro doses de calcário dolomítico (0, 1.100, 2.700 e 4.300 kg ha-1), com PRNT = 71,2 %, e nas subparcelas, duas doses de gesso agrícola (0 e 2.100 kg ha-1). O calcário e o gesso foram aplicados em superfície, sem incorporação. Houve alta correlação na determinação de Ca e Mg trocável entre os métodos de percolação com solução de KCl e resina trocadora de íons. A extração pelo método da resina trocadora de íons superestimou os teores de Ca e Mg trocáveis em solo com recente aplicação de calcário em superfície. A aplicação de gesso em superfície reduziu a dissolução do calcário na camada superficial (0-0,10 m). Os teores de Ca e Mg não-trocáveis podem ser utilizados para estimar a quantidade de calcário residual no solo.