Development of an ultra mini-oxygenator for use in low-volume, buffer-perfused preparations

Introduction: Small animal models are widely used in basic research. However, experimental systems requiring extracorporeal circuits are frequently confronted with limitations related to equipment size. This is particularly true for oxygenators in systems with limited volumes. Thus we aimed to develop and validate an ultra mini-oxygenator for low-volume, buffer-perfused systems. Methods: We have manufactured a series of ultra mini-oxygenators with approximately 175 aligned, microporous, polypropylene hollow fibers contained inside a shell, which is sealed at each of the two extremities to isolate perfusate and gas compartments. With this construction, gas passes through hollow fibers, while perfusate circulates around fibers. Performance of ultra mini-oxygenators (oxygen partial pressure (PO2 ), gas and perfusate flow, perfusate pressure and temperature drop) were assessed with modified Krebs-Henseleit buffer in an in vitro perfusion circuit and an ex vivo rat heart preparation. Results: Mean priming volume of ultra mini-oxygenators was 1.2±0.5 mL and, on average, 86±6% of fibers were open (n=17). In vitro, effective oxygenation (PO2=400-500 mmHg) was achieved for all flow rates up to 50 mL/min and remained stable for at least 2 hours (n=5). Oxygenation was also effective and stable (PO2=456±40 mmHg) in the isolated heart preparation for at least 60 minutes ("venous" PO2=151±11 mmHg; n=5). Conclusions: We have established a reproducible procedure for fabrication of ultra mini-oxygenators, which provide reliable and stable oxygenation for at least 60-120 min. These oxygenators are especially attractive for pre-clinical protocols using small, rather than large, animals.

Assessment of Potential Orthodontic Mini-implant Insertion Sites Based on Anatomical Hard Tissue Parameters: A Systematic Review

To estimate the applicability of potential sites for insertion of orthodontic mini-implants (OMIs) by a systematic review of studies that used computed tomography (CT) or cone beam CT to evaluate anatomical bone quality and quantity parameters, such as bone thickness, available space, and bone density.

Oral lichenoid contact lesions induced by areca nut and betel quid chewing: a mini review

Betel quid (BQ) and areca nut chewing is widely prevalent in many parts of Asia and Asian-migrant communities throughout the world. Global reports estimate 600 million users. Sufficient evidence of carcinogenicity has been found for BQ and its main ingredient, areca nut. BQ areca nut users have an increased risk of potentially malignant disorders. Among chewers, BQ remains in contact with the oral mucosa for prolonged periods. This review examines the clinical and pathological aspects of lichenoid lesions caused by areca nut and BQ, a condition that has received little attention in the published literature.

Mutations in the bovine ABCG2 and the ovine MSTN gene added to the few quantitative trait nucleotides identified in farm animals: a mini-review

The progress in molecular genetics in animal breeding is moderately effective as compared to traditional animal breeding using quantitative genetic approaches. There is an extensive disparity between the number of reported quantitative trait loci (QTLs) and their linked genetic variations in cattle, pig, and chicken. The identification of causative mutations affecting quantitative traits is still very challenging and hampered by the cloudy relationship between genotype and phenotype. There are relatively few reports in which a successful identification of a causative mutation for an animal production trait was demonstrated. The examples that have attracted considerable attention from the animal breeding community are briefly summarized and presented in a table. In this mini-review, the recent progress in mapping quantitative trait nucleotides (QTNs) are reviewed, including the ABCG2 gene mutation that underlies a QTL for fat and protein content and the ovine MSTN gene mutation that causes muscular hypertrophy in Texel sheep. It is concluded that the progress in molecular genetics might facilitate the elucidation of the genetic architecture of QTLs, so that also the high-hanging fruits can be harvested in order to contribute to efficient and sustainable animal production.

Mapping the Operation of the Miniature Combustion Aerosol Standard (Mini-CAST) Soot Generator

The Jing Ltd. miniature combustion aerosol standard (Mini-CAST) soot generator is a portable, commercially available burner that is widely used for laboratory measurements of soot processes. While many studies have used the Mini-CAST to generate soot with known size, concentration, and organic carbon fraction under a single or few conditions, there has been no systematic study of the burner operation over a wide range of operating conditions. Here, we present a comprehensive characterization of the microphysical, chemical, morphological, and hygroscopic properties of Mini-CAST soot over the full range of oxidation air and mixing N-2 flow rates. Very fuel-rich and fuel-lean flame conditions are found to produce organic-dominated soot with mode diameters of 10-60nm, and the highest particle number concentrations are produced under fuel-rich conditions. The lowest organic fraction and largest diameter soot (70-130nm) occur under slightly fuel-lean conditions. Moving from fuel-rich to fuel-lean conditions also increases the O:C ratio of the soot coatings from similar to 0.05 to similar to 0.25, which causes a small fraction of the particles to act as cloud condensation nuclei near the Kelvin limit (kappa similar to 0-10(-3)). Comparison of these property ranges to those reported in the literature for aircraft and diesel engine soots indicates that the Mini-CAST soot is similar to real-world primary soot particles, which lends itself to a variety of process-based soot studies. The trends in soot properties uncovered here will guide selection of burner operating conditions to achieve optimum soot properties that are most relevant to such studies.

Mini-arthrotomy for lateral discoid menisci in children

BACKGROUND: Long-term results after partial, extended, or complete resection of lateral discoid meniscus in children revealed knee arthritis. The purpose of this study was to evaluate whether the operative approach, arthrotomy or arthroscopy, has an impact on the outcome and the development of arthritis. METHODS: A retrospective comparison of 2 well matching groups totaling 40 children with symptomatic lateral discoid meniscus (48 knees, mean age 8.9 years, 13 male and 27 female patients). Meniscus resection was performed via mini-arthrotomy in group 1 (n=17 patients, 20 knees) and arthroscopically in group 2 (n=23 patients, 28 knees). RESULTS: In the follow-up (mean 57 months in group 1, 62 months in group 2), functional results indicated a trend to better results in the International Knee Documentation Committee score (P=0.12) and in the Lysholm score for group 1 (P=0.13) but not in the Ikeuchi score (P=0.48). The comparison of the radiographic arthritis grading in the follow-up showed no significant arthritis in either group (P=0.22). The overall complication rate was similar in both groups (2/20, 10% in group 1; 3/28, 12% in group 2). CONCLUSIONS: Most likely because of the appropriate visualization of the children's joint and the easier instrumentation, the mini-arthrotomy led to slightly superior results compared with those after arthroscopic resection regarding functional outcome and 5 years after surgery. We can recommend the mini-arthrotomy for the resection of lateral discoid meniscus particularly in young children with narrow joint spaces and for surgeons that are not familiar with arthroscopies of small joints. LEVEL OF EVIDENCE: III (therapeutic study, case series with control group).